| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, features and cleanup for 5.17
Includes some fixes that were either late breaking, low priority or
complex enough to not be good to rush in late in the cycle.
Tree rebased today to fix up some trivial issues + pull in a fix that
was previously on the fixes-togreg branch. Vast majority have been
in linux-next for some time now.
New device support
* adi,ad7293
- New driver and bindings for this Power Amplifier drain current
controller. A complex device with various related monitoring functions.
* adi,ad75513R
- New driver and bindings for this combined ADC and DAC device.
- A few follow up fixes.
* adi,admv8818
- New driver (and type) for this 2-18GHz filter device. Includes
bindings and ABI documentation to allow clk_notifier based auto
adjustment of the filters in appropriate applications.
* liteon,ltr501
- Support for the ltr303. ID and chip specific info table.
* xilinx,ams
- New generic firmware function fwnode_iomap() as used in this driver.
- New driver and bindings for this ADC and on-chip sensors as found
in various Xilinx devices.
Core
* Introduced IIO_VAL_INT_64 which uses val and val2 in IIO callbacks to
form a 64 bit integer when higher precision needed.
* Allow IIO_ENUM_AVAILABLE to be used with different shared values.
* Fix a long term issue with scheduling whilst atomic when iio_trig_poll()
is called but no trigger consumers are actually enabled and hence the
trigger may be reenabled from the interrupt handler. Seen in the wild
on the tsc2046.
* Mark iio_device_type const.
* buffer: Use a separate index variable to simplify code.
* buffer-dma: Clear out unused struct iio_buffer_block
* buffer-dmaengine: Switch to cheaper round_down() as power of 2 values.
Tests/tools
* format_value
- Check against NULL returns from allocations in tests.
- Add IIO_VAL_INT_64 test case.
* event_monitor
- Flush the output after event to given more consistent latency
when tool output piped to other programs.
Driver Features
* axp20x
- Add support for NTC thermistor channel and document TS pin binding.
* arm,scmi
- Add reading of raw channel values (using IIO_VAL_INT_64)
* liteon,ltr501
- Add proximity-near-level support and dt-binding.
Tree wide cleanup
* Remove no-op trigger ops from multiple drivers.
* Stop using dev_get_drvdata() on the iio_dev->dev in various drivers
and then stop assigning it to allow this to be used for other purposes.
We can always get to the indio_dev using dev_to_iio_dev() which is
a container_of() based approach. Also cleanup up some related unnecessary
convoluted cases.
- atmel,at91-sam5d2
- nxp,imx7d
- meas,ms5611
- st,st_sensors
* Where available (or easy to introduce) use the scan_type.* values
in place of a second copy for read_raw and similar paths.
- adi,ad7266
- bosch,bma220
- fsl,mac3110
- fsl,mma7455
- fsl,mpl3115
- kionix,kcjk-1013
- sensortek,stk8ba50
- sensortek,stk8312
- ti,adc12138
- ti,ads1015
- vti,sca3000
- xilinx,xadc-core
* Switch drives over to generic firmware properties including appropriate
header changes to avoid including of.h
- Various DACs had false CONFIG_OF dependencies.
- dpot-dac
- envelope-detector
- adi,ad5755
- adi,ad5758
- capella,cm3605
- maxim,max9611
- microchip,mcp41010
- microchip,mcp3911
- ti,adc12138
* Trivial clang warning fixes for W=1 warnings.
Driver specific cleanup and minor fixes
* adi,ad7606
- Comment fixes.
* ams,ad3935
- Drop pointless cast to the same type.
* atmel,at91-sama5d2
- Fix wrong cast of iio_dev->dev to platform_device that happened to
be harmless.
* fsl,mma7660
- Stop i2c remove() function returning an error code. Part of a rework
to eventually stop returning anything from these.
* fsl,mma8452
- Use correct type for local irqreturn_t.
* nxp,imx8mq
- Maintainer email address update.
* nxp,lpc18xx_adc
- Ensure clk_prepare_enable() called before clk_get_rate().
- Switch of.h for mod_devicetable.h to reflect no of specific functions,
just the id table.
* renesas,rzg2l
- Drop a dev_err() that just duplicates error printed in platform_get_irq()
* sgx,vz89x
- Drop pointless cast.
* st,lsm6dsx
- Make it possible to disable the sensorhub from DT to avoid a corner
case where the address of a slave device many be accidentally modified.
* st,stm32-adc
- Stop leaking an of_node in an error path.
* st,stmp2
- Avoid wrong sized type for bit field which could result in
over-reading (harmless). Precursor to enabling -Warray-bounds.
* ti,adc081c
- Put back some ACPI support for non standards compliant ADC081C
ID because it is known to be in the wild on some Aaeon boards.
* ti,ads8688
- Cleanup redundant local ret variable assignment.
* ti,ina2xx-adc
- Use helper macro kthread_run() to replace some boilerplate.
- Avoid double reference counting.
- Drop pointless cast.
* xilinx,xadc
- Make the IRQ optional as not always wired to the host system.
* tag 'iio-for-5.17a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (103 commits)
iio: adc: ti-adc081c: Partial revert of removal of ACPI IDs
iio:addac:ad74413r: Fix uninitialized ret in a path that won't be hit.
MAINTAINERS: Add maintainer for xilinx-ams
dt-bindings: iio: adc: Add Xilinx AMS binding documentation
iio: adc: Add Xilinx AMS driver
device property: Add fwnode_iomap()
iio:accel:kxcjk-1013: Mark struct __maybe_unused to avoid warning.
iio:accel:bmc150: Mark structure __maybe_unused as only needed with for pm ops.
iio:dummy: Drop set but unused variable len.
iio:magn:ak8975: Suppress clang W=1 warning about pointer to enum conversion.
iio:imu:inv_mpu6050: Suppress clang W=1 warning about pointer to enum conversion.
iio:imu:inv_icm42600: Suppress clang W=1 warning about pointer to enum conversion.
iio:dac:mcp4725: Suppress clang W=1 warning about pointer to enum conversion.
iio:amplifiers:hmc425a: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:ti-ads1015: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:rcar: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:ina2xx-adc: Suppress clang W=1 warning about pointer to enum conversion.
iio:accel:bma180: Suppress clang W=1 warning about pointer to enum conversion.
drivers:iio:dac: Add AD3552R driver support
dt-bindings: iio: dac: Add adi,ad3552r.yaml
...
|
|
The AMS includes an ADC as well as on-chip sensors that can be used to
sample external voltages and monitor on-die operating conditions, such
as temperature and supply voltage levels. The AMS has two SYSMON blocks.
PL-SYSMON block is capable of monitoring off chip voltage and
temperature.
PL-SYSMON block has DRP, JTAG and I2C interface to enable monitoring
from an external master. Out of these interfaces currently only DRP is
supported. Other block PS-SYSMON is memory mapped to PS.
The AMS can use internal channels to monitor voltage and temperature as
well as one primary and up to 16 auxiliary channels for measuring
external voltages.
The voltage and temperature monitoring channels also have event capability
which allows to generate an interrupt when their value falls below or
raises above a set threshold.
Co-developed-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Anand Ashok Dumbre <anand.ashok.dumbre@xilinx.com>
Link: https://lore.kernel.org/r/20211203212358.31444-4-anand.ashok.dumbre@xilinx.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
We could probably drop a lot more of these, but for now this removes
unnecessary restrictions on stand alone ADC devices.
For these 3 drivers the false dependency seems to date all
the way back to their initial introduction.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
|
|
Nothing in this driver depends on OF firmware so drop the dependency
and update the headers to remove the false impression such a dependency
exists.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
|
|
Commit 1e23dcaa1a9f ("iio: imx8qxp-adc: Add driver support for NXP IMX8QXP
ADC") adds the config IMX8QXP_ADC for this new driver, which depends on
the non-existing config ARCH_MXC_ARM64.
Hence, ./scripts/checkkconfigsymbols.py warns:
ARCH_MXC_ARM64
Referencing files: drivers/iio/adc/Kconfig
Probably, the existing config ARCH_MXC is intended to be referred here.
So, repair the dependency to refer to that config.
Fixes: 1e23dcaa1a9f ("iio: imx8qxp-adc: Add driver support for NXP IMX8QXP ADC")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20211111083954.6286-1-lukas.bulwahn@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Otherwise most build checks will omit this driver from a compile-test due
to it's dependency only on the BERLIN_ARCH symbol.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210926192642.4051329-2-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add
driver support for this ADC.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210925020555.129-2-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Describe better which driver applies to which SoC, to make configuring
kernel for Samsung SoC easier.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210924133515.112357-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add ADC driver support for Renesas RZ/G2L A/D converter in SW
trigger mode.
A/D Converter block is a successive approximation analog-to-digital
converter with a 12-bit accuracy and supports a maximum of 8 input
channels.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210804202118.25745-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Basically the TI TSC2046 touchscreen controller is 8 channel ADC optimized for
the touchscreen use case. By implementing it as an IIO ADC device, we can
make use of resistive-adc-touch and iio-hwmon drivers.
Polled readings are currently not implemented to keep this patch small, so
iio-hwmon will not work out of the box for now.
So far, this driver was tested with a custom version of resistive-adc-touch driver,
since it needs to be extended to make use of Z1 and Z2 channels. The X/Y
are working without additional changes.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210428073208.19570-4-o.rempel@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Because a dependency on HAS_IOMEM and OF was added for the ADI AXI ADC
driver, this makes the AD9467 driver have some build/dependency issues
when OF is disabled (typically on ACPI archs like x86).
This is because the selection of the AD9467 enforces the ADI_AXI_ADC symbol
which is blocked by the OF (and potentially HAS_IOMEM) being disabled.
To fix this, we make the AD9467 driver depend on the ADI_AXI_ADC symbol.
The AD9467 driver cannot operate on it's own. It requires the ADI AXI ADC
driver to stream data (or some similar IIO interface).
So, the fix here is to make the AD9467 symbol depend on the ADI_AXI_ADC
symbol. At some point this could become it's own subgroup of high-speed
ADCs.
Fixes: be24c65e9fa24 ("iio: adc: adi-axi-adc: add proper Kconfig dependencies")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210324182746.9337-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
"an" should be "and".
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20210401150810.227168-1-jic23@kernel.org
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
1st set of IIO/counter device support, features and cleanup in the 5.13 cycle
Big set in here from Alexandru Ardelean enabling multiple buffer support.
This includes providing a new directory per buffer that combines
what was previously in buffer/ and scan_elements/. Old interfaces still
in place for compatiblity.
Note immuatable branch for scmi patches to allow for some significant
rework going on in that subsystem. Merge required updating to reflect
some changes in IIO.
Late rebase to fix some wrong fixes tags due to some earlier rebases
made necessary by messing up the immutable branch.
IIO New Device Support
* adi,ad5686
- Add info to support AD5673R and AD5677R
* bosch,bmi088
- New driver supporting this accelerometer + gyroscope
* cros_ec_mkbp
- New driver for this proximity sensor that exposes a 'front'
sensor. Very simple switch like device, but driver allows it
to share interface with more sophisticated proximity sensors.
* iio_scmi
- New driver to support ARM SCMI protocol to expose underlying
accelerometers and gyroscopes via this firmware interface.
* st,st_magn
- Add ID for IISMDC magnetometer.
* ti,ads131e0
- New driver supporting ads131e04, ads131e06 and ads131e08 24 bit ADCs
Counter New Device Support
* IRQ or GPIO based counter
- New driver for a conceptually simple counter that uses interrupts
to perform the count.
Features
* core
- Dual buffer supprt including:
Various helpers to centralize handling of bufferer related elements.
Document existing and new IOCTLs
Register the IIO chrdev only if it can actually be used for anything.
Rework attribute group creation in the core (lots of patches)
Merge buffer/ and scan_elements/ entries into one list + maintain
backwards compatible set.
Introduce the internal logic and IOCTL to allow multiple buffers
+ access to an anon FD per buffer to actually read from it.
Tidy up tools/iio/iio_generic_buffer and switch to new interfaces.
Update ABI docs.
A few follow up fixes, unsuprising as this was a huge bit of rework.
- Move common case setting of trig->parent to the core.
- Provide an iio_read_channel_processed_scale() to avoid loss of
precision from iio_read_channel_processed() then applying integer
scale. Use it in ntc_thermistor driver in hwmon.
- Allow drivers to specify labels from elsewhere than DT. Use it for
bmc150 and kxcjk-1013 labels related to position on 2 in one tablets.
- Document label usage for proximity and accelerometer sensors.
- Some local variable renames for consistency
tools
- Add -a parameter to iio_event_monitor to allow autoenabling of events.
* acpi_als
- Add trigger support for devices that don't support notification method.
* adi,ad7124
- Allow more than 8 channels. This is a complex little device, but is
capable of supporting up to 16 channels if the share certain
configuration settings.
* hrtimer-trigger
- Support sampling frequency below 1Hz.
* mediatek,mt8195-auxadc
- Add compatible to binding docs (always also includes mt8173)
* st,stm32-adc
- Enable timetamps when not using DMA.
* vishay,vcnl3020
- Sampling frequency control.
Cleanup and minor fixes:
* treewide
- Use some getter and setter functions instead of opencoding.
- Set of fixes for pointless casts in various drivers.
- Avoid wrong kernel-doc marking on comment blocks.
- Fix various other minor kernel-doc issues shown by W=1
* core
- Use a signed temporary for IIO_VAL_FRACTIONAL_LOG2 to avoid odd casts.
- Fix IIO_VAL_FRACTIONAL_LOG2 for values between -1.0 and 0.0
- Add unit tests for iio_format_value()
* docs
- Fix formatting/typos in iio_configfs.rst and buffers.rst
- Add documentation of index in buffers.rst
- Fix scan element description
- Avoid some issues with HTML generation from ABI docs by moving
duplicated defintions to more generic files.
- Drop reference to long dead mailing list.
* 104-quad
- Remove left over deprecated IIO counter ABI.
* adi,adi-axi-adc
- Fix wrong bit of docs.
* adi,ad5791
- Typos
* adi,ad9834
- Switch to device managed functions in probe.
* adi,adis*
- Add and use helpers for locking to reduced duplication.
* adi,adis16480
- Fix calculation of sampling frequency when using pulse per second input.
* adi,adis16475
- Calculate the IMU scaled internal sampling rate and runtime depending
on sysfs based configuration rather than getting from DT. Drop now
unnecessary property from DT bindings doc.
* cros_ec
- Fix result of a series of recent changes that means extended buffer
attributes turn up in the wrong place. Too complex to revert the
various patches unfortunately so this is a bit messy.
* fsl,mma3452
- Indentation cleanup.
* hid-sensors
- Size of storage needs to increase for some parts when using quaternions.
- Move the get sensistivity attribute to hid-sensors-common to reduce
duplication. Enable it for more device types.
- Correctly handle relative sensitivity if reported that way including
documenting the new ABI.
* maxim,max517
- Use device managed functions in probe.
* mediatek,mt6360-adc
- Use asm/unaligned.h instead of directly including
unaligned/be_byteshift.h
* novuton,npcm-adc
- Local lock instead of missusing mlock.
* semtech,sx9500
- Typos
* st,sensor
- typo fix
* st,spear-adc
- Local lock instead of missusing mlock.
* st,stm32-adc
- Long standing HAS_IOMEM dependency fix.
* st,stm32-counter
- Remove left over deprecated IIO counter ABI.
* ti,palmas-adc
- Local lock instead of missusing mlock.
* ti,tmp007
- Switch to device managed functions in probe.
Other
* MAINTAINERS
- Move Peter Meerwald-Stadler to Credits at his request
* tag 'iio-for-5.13a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (119 commits)
iio: acpi_als: Add trigger support
iio: acpi_als: Add local variable dev in probe
iio: acpi_als: Add timestamp channel
iio: adc: ad7292: Modify the bool initialization assignment
iio: cros: unify hw fifo attributes without API changes
iio: kfifo: add devm_iio_triggered_buffer_setup_ext variant
iio: event_monitor: Enable events before monitoring
dt-bindings: iio: adc: Add compatible for Mediatek MT8195
iio:magnetometer: Add Support for ST IIS2MDC
dt-bindings: iio: st,st-sensors add IIS2MDC.
staging: iio: ad9832: kernel-doc fixes
iio:dac:max517.c: Use devm_iio_device_register()
iio:cros_ec_sensors: Fix a wrong function name in kernel doc.
iio: buffer: kfifo_buf: kernel-doc, typo in function name.
iio: accel: sca3000: kernel-doc fixes. Missing - and wrong function names.
iio: adc: adi-axi-adc: Drop false marking for kernel-doc
iio: adc: cpcap-adc: kernel-doc fix - that should be _ in structure name
iio: dac: ad5504: fix wrong part number in kernel-doc structure name.
iio: dac: ad5770r: kernel-doc fix case of letter R wrong in structure name
iio: adc: ti-adc084s021: kernel-doc fixes, missing function names
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO and counter fixes for the 5.12 cycle
adi,ad7949
* Fix a wrong bitmask that could lead to an undefined bit being included.
adi,adi-axi-adc
* Add missing Kconfig dependencies
adi,adis16400
* Wrong error code handling in adis16400 that could lead to failed probe.
hid-sensor-humidity, temperature
* Fix alignment and space for timestamp channel.
hid-sensor-prox
* Fix an issue with handling of exponent on the channel scaling.
invensense,mpu3050
* Fix a hole in error handling.
qcom,spi-vadc
* Correct scaling
st,ab8500-adc
* Fix wrong scaling (by factor of 1000)
st,stm32-adc
* Add missing HAS_IOMEM dependency
st,stm32-timer-cnt
* Report count when running off internal clock
* Fix issue with not checking ceiling before trying to write to hardware
* Ensure driver doesn't have stashed state which doesn't match hardware by
rereading from hardware in a slow path.
* tag 'iio-fixes-for-5.12a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: gyro: mpu3050: Fix error handling in mpu3050_trigger_handler
iio: hid-sensor-temperature: Fix issues of timestamp channel
iio: hid-sensor-humidity: Fix alignment issue of timestamp channel
counter: stm32-timer-cnt: fix ceiling miss-alignment with reload register
counter: stm32-timer-cnt: fix ceiling write max value
counter: stm32-timer-cnt: Report count function when SLAVE_MODE_DISABLED
iio: adc: ab8500-gpadc: Fix off by 10 to 3
iio:adc:stm32-adc: Add HAS_IOMEM dependency
iio: adis16400: Fix an error code in adis16400_initial_setup()
iio: adc: adi-axi-adc: add proper Kconfig dependencies
iio: adc: ad7949: fix wrong ADC result due to incorrect bit mask
iio: hid-sensor-prox: Fix scale not correct issue
iio:adc:qcom-spmi-vadc: add default scale to LR_MUX2_BAT_ID channel
|
|
The ADS131E0x are a family of multichannel, simultaneous sampling,
24-bit, delta-sigma, analog-to-digital converters (ADCs) with a
built-in programmable gain amplifier (PGA), internal reference
and an onboard oscillator.
Datasheet: https://www.ti.com/lit/ds/symlink/ads131e08.pdf
Signed-off-by: Tomislav Denis <tomislav.denis@avl.com>
Link: https://lore.kernel.org/r/20210202084107.3260-2-tomislav.denis@avl.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Seems that there are config combinations in which this driver gets enabled
and hence selects the MFD, but with out HAS_IOMEM getting pulled in
via some other route. MFD is entirely contained in an
if HAS_IOMEM block, leading to the build issue in this bugzilla.
https://bugzilla.kernel.org/show_bug.cgi?id=209889
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Seems that there are config combinations in which this driver gets enabled
and hence selects the MFD, but with out HAS_IOMEM getting pulled in
via some other route. MFD is entirely contained in an
if HAS_IOMEM block, leading to the build issue in this bugzilla.
https://bugzilla.kernel.org/show_bug.cgi?id=209889
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20210124195034.22576-1-jic23@kernel.org
|
|
The ADI AXI ADC driver requires IO mem access and OF to work. This change
adds these dependencies to the Kconfig symbol of the driver.
This was also found via the lkp bot, as the
devm_platform_ioremap_resource() symbol was not found at link-time on the
S390 architecture.
Fixes: ef04070692a21 ("iio: adc: adi-axi-adc: add support for AXI ADC IP core")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210210105044.48914-1-alexandru.ardelean@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The xilinx-xadc IIO driver currently has support for the XADC in the Xilinx
7 series FPGAs. The system-monitor is the equivalent to the XADC in the
Xilinx UltraScale and UltraScale+ FPGAs.
The IP designers did a good job at maintaining backwards compatibility and
only minor changes are required to add basic support for the system-monitor
core.
The non backwards compatible changes are:
* Register map offset was moved from 0x200 to 0x400
* Only one ADC compared to two in the XADC
* 10 bit ADC instead of 12 bit ADC
* Two of the channels monitor different supplies
Add the necessary logic to accommodate these changes to support the
system-monitor in the XADC driver.
Note that this patch does not include support for some new features found
in the system-monitor like additional alarms, user supply monitoring and
secondary system-monitor access. This might be added at a later time.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Anand Ashok Dumbre <anandash@xilinx.com>
Reviewed-by: Anand Ashok Dumbre <anandash@xilinx.com>
Link: https://lore.kernel.org/r/20200922134624.13191-2-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add MT6360 ADC driver including Charger Current, Voltage, and
Temperature.
Signed-off-by: Gene Chen <gene_chen@richtek.com>
Link: https://lore.kernel.org/r/1603181267-15610-4-git-send-email-gene.chen.richtek@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This tries to solve a warning reported by the lkp bot:
>> drivers/iio/adc/at91_adc.c:1439:34: warning: unused variable
>> 'at91_adc_dt_ids' [-Wunused-const-variable]
static const struct of_device_id at91_adc_dt_ids[] = {
^
1 warning generated.
This warning has appeared after the AT91_ADC driver compilation has been
enabled via the COMPILE_TEST symbol dependency.
The warning is caused by the 'of_match_ptr()' helper which returns NULL if
OF is undefined. This driver should build only for device-tree context, so
a dependency on the OF Kconfig symbol has been added.
Also, the usage of of_match_ptr() helper has been removed since it
shouldn't ever return NULL (because the driver should not be built for the
non-OF context).
Fixes: 4027860dcc4c ("iio: Kconfig: at91_adc: add COMPILE_TEST dependency to driver")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200930135048.11530-4-alexandru.ardelean@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of features and cleanups for IIO in 5.10
We have a couple of changes that apply to large sets of drivers, so
I have grouped those to keep this short.
There are a few late breaking fixes in here that can wait for the
merge window.
dt yaml conversions
-------------------
* adi,ad7768-1
* adi,ad7949
* aspeed,ast2400
* cosmic,10001-adc
* dlg,da9150-gpadc
* fsl,imx25-gcq
* fsl,imx7d-adc
* fsl,vf610
* holt,hi8435
* marvell,berlin2-adc
* motorola,cpcap-adc
* nuvoton,nau7802
* nuvoton,npcm750-adc
* nxp,lpc1850-adc
* nxp,lpc3220
* sprd,sc2720-adc
* st,stmpe-adc
* ti,adc12138
* ti,ads1015
* ti,ads7950
* ti,twl4030-madc
Features
--------
* adxrs290
- Add triggered buffer support and expose data ready signal as a possible
trigger. Includes updating bindings.
- Add debugfs hooks for register access.
* mlx90632
- Add a clear user interface to override the measured ambient temperature.
* vl53l0x
- Add IRQ support including dt bindings.
Cleanups and minor fixes
------------------------
(groups)
Replace mlock with local lock:
* adf4350
* exynos-adc
* fls-imx25-gcq
* stm32-dac
devm use to simplify probe error handling and remove functions.
* adis16201
* adis16203
* adis16209
* adis16240
* adis16136
* adis16260
* adis16400
* adis16460
* adis16480
* adis library - drop unused adis_setup_buffer_and_trigger()
of_match_ptr removal and incorrect ACPI binding removal
of_match_ptr() rarely makes sense in an IIO driver as space saving
is trivial and it breaks ACPI PRP0001 based instantiation.
Mostly this series is about removing examples that get copied into new
drivers.
* ad2s1200
* ad5272
* ad5446
* ad5592r
* ad5593r
* ad5703
* ak8974
* ak8975
* ams-iaq-core
* as3935
* atlas-sensor
* ds1803
* hdc100x
* htu21
* icp10100
* lmp91000
* pulsedlight
* max30102
* max5432
* max5481
* mcp4018
* mcp4131
* mcp4531
* mcp4725
* ms5611
* ms5637
* si7020
* sgp30
* ti-dac082s085
* ti-dac5571
* tmp007
* tsys01
* vz89x
* zpa2326
kernel-doc fixes
* iio-core
* ad7303
* ad7947
* adis16080
* adis16400
* iio_dummy_evgen
* sgp30
Fixes for buffer alignment when passed to iio_push_to_buffers_with_timestamp()
This is a long running effort. There are a few more drivers to come.
* inv_mpu6050
* itg3200
* si1145
* st_lsm6dsx
* ti-adc0832
* ti-adc12138
(not driver focused)
* MAINTAINERS
- Consolidate Analog Device IIO entries whilst removing Beniamin Bia.
- Remove Hartmut Knaack as a listed IIO maintainer as he hasn't been
active for a long time and people are getting intermitted bounces.
* Add __printf() markings to a few functions that were missing them.
* drop some rotted documentation from staging.
* rework buffer sysfs file creation (precursor to multiple buffer support)
(individual drivers)
* ad5592r
- Fix use of true for IIO_SHARED_BY_TYPE
- Tidy up locking and indentation.
* ad9467
- Improve error message on chip-id missmatch.
- Use more appropriate error value if chip-id not recognised.
* adis-library
- Simplify burst mode handling.
* adxrs290
- Make sure to switch device to standby mode during remove.
* as73211
- Increase measurement timeout as seems some devices are slower.
* bma180
- Fix use of true fo IIO_SHARED_BY_TYPE
* exynos_adc
- Update binding to require second interrut with touch screen.
- Update binding to not require syscon on S5Pv210
* hmc5843
- Fix use of true for IIO_SHARED_BY_TYPE
* inv_mpu6050
- Use regmap_noinc_read() for fifo reading.
* palmas_gpadc
- Use module_platform_driver() to remove boilerplate.
* meson-saradc
- style consistency fixes
* rockchip_saradc
- Allow compile testing with !ARM.
* st_lsm6dsx
- Changing scaling factor to use IIO_VAL_INT_PLUS_NANO to improve precision.
- Fix an issue with unchecked return value.
* stm32-adc
- Fix a missing return introduced in dev_err_probe() patch earlier in
cycle.
* sx9310
- Prefer async mode for probe as paticularly slow startup.
* vcnl4000
- Add missing interrupt property to dt binding.
* tag 'iio-for-5.10b-take2' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (126 commits)
dt-bindings: iio: vishay,vcnl4000: add interrupts property
iio:imu:inv_mpu6050: Use regmap_noinc_read for fifo reads.
iio:imu:inv_mpu6050 Fix dma and ts alignment and data leak issues.
iio:adc:ti-adc12138 Fix alignment issue with timestamp
iio:adc:ti-adc0832 Fix alignment issue with timestamp
iio:imu:st_lsm6dsx Fix alignment and data leak issues
iio:light:si1145: Fix timestamp alignment and prevent data leak.
iio:gyro:itg3200: Fix timestamp alignment and prevent data leak.
iio:imu:st_lsm6dsx: check st_lsm6dsx_shub_read_output return
iio: adc: exynos_adc: Replace indio_dev->mlock with own device lock
dt-bindings:iio:adc:holt,hi8435 yaml conversion
dt-bindings:iio:adc:adi,ad7768-1 yaml conversion
dt-bindings:iio:adc:adi,ad7949 yaml conversion
dt-bindings:iio:adc:dlg,da9150-gpadc yaml conversion
dt-bindings:iio:adc:motorola,cpcap-adc yaml conversion
dt-bindings:iio:adc:nxp,lpc3220-adc yaml conversion
dt-bindings:iio:adc:nxp,lpc1850-adc yaml conversion
dt-bindings:iio:adc:fsl,imx25-gcq yaml conversion
dt-bindings:iio:adc:fsl,imx7d-adc yaml conversion
dt-bindings:iio:adc:ti,ads1015 yaml conversion
...
|
|
We want the staging/iio changes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There seems no reason to allow for compile-testing on ARM only, so
remove this restriction.
Build-tested with allyesconfig on x86.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200904170416.16061-1-alex.dewar90@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This driver cannot be instantiated from ACPI due to it's use of
syscon_regmap_lookup_by_phandle() but in the interests of clearing
this anti pattern out of IIO, let us switch to an explicit
check in Kconfig and remove the protections on the of_match_table
The switch of header is because we only use of_device_id
in here and that is defined in mod_devicetable.h not of.h.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
|
|
The kernel fails to compile due to undefined reference to
devm_iio_triggered_buffer_setup() if IIO_TRIGGERED_BUFFER is not
enabled. The original patch [1] had this dependency. But somehow it
didn't make it into the kernel tree. Re-add it.
[1] https://lore.kernel.org/lkml/20200623233011.2319035-3-heiko@sntech.de/
Fixes: 4e130dc7b413 ("iio: adc: rockchip_saradc: Add support iio buffers")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Immutable branch may be needed in input for a joystick set that is
dependent on it.
|
|
The SADC component in JZ47xx SoCs provides support for touchscreen
operations (pen position and pen down pressure) in single-ended and
differential modes.
The touchscreen component of SADC takes a significant time to stabilize
after first receiving the clock and a delay of 50ms has been empirically
proven to be a safe value before data sampling can begin.
Of the known hardware to use this controller, GCW Zero and Anbernic RG-350
utilize the touchscreen mode by having their joystick(s) attached to the
X/Y positive/negative input pins.
JZ4770 and later SoCs introduce a low-level command feature. With it, up
to 32 commands can be programmed, each one corresponding to a sampling
job. It allows to change the low-voltage reference, the high-voltage
reference, have them connected to VCC, GND, or one of the X-/X+ or Y-/Y+
pins.
This patch introduces support for 6 stream-capable channels:
- channel #0 samples X+/GND
- channel #1 samples Y+/GND
- channel #2 samples X-/GND
- channel #3 samples Y-/GND
- channel #4 samples X+/X-
- channel #5 samples Y+/Y-
Being able to sample X-/GND and Y-/GND is useful on some devices, where
one joystick is connected to the X+/Y+ pins, and a second joystick is
connected to the X-/Y- pins.
All the boards which probe this driver have the interrupt provided from
Device Tree, with no need to handle a case where the IRQ was not provided.
Co-developed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Since changes can come from all sort of places, it may make sense to have
this symbol as a dependency to make sure that the 'make allmodconfig' &&
'make allyesconfig' build rules cover this driver as well for a
compile-build/test.
It seemed useful [recently] when trying to apply a change for this.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the large set of staging and IIO driver changes for 5.8-rc1
Nothing major, but a lot of new IIO drivers are included in here,
along with other core iio cleanups and changes.
On the staging driver front, again, nothing noticable. No new
deletions or additions, just a ton of tiny cleanups all over the tree
done by a lot of different people. Most coding style, but many actual
real fixes and cleanups that are nice to see.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (618 commits)
staging: rtl8723bs: Use common packet header constants
staging: sm750fb: Add names to proc_setBLANK args
staging: most: usb: init return value in default path of switch/case expression
staging: vchiq: Get rid of VCHIQ_SERVICE_OPENEND callback reason
staging: vchiq: move vchiq_release_message() into vchiq
staging: vchi: Get rid of C++ guards
staging: vchi: Get rid of not implemented function declarations
staging: vchi: Get rid of vchiq_status_to_vchi()
staging: vchi: Get rid of vchi_service_set_option()
staging: vchi: Merge vchi_msg_queue() into vchi_queue_kernel_message()
staging: vchiq: Move copy callback handling into vchiq
staging: vchi: Get rid of vchi_queue_user_message()
staging: vchi: Get rid of vchi_service_destroy()
staging: most: usb: use function sysfs_streq
staging: most: usb: add missing put_device calls
staging: most: usb: use correct error codes
staging: most: usb: replace code to calculate array index
staging: most: usb: don't use error path to exit function on success
staging: most: usb: move allocation of URB out of critical section
staging: most: usb: return 0 instead of variable
...
|
|
Add support for 8-bit resolution ADC readings for input power
supply and battery charging measurement. Provides voltage, current
readings to mp2629 power supply driver.
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new IIO device support, features and cleanup for the 5.8 cycle
Usual mix of new drivers, new support in old drivers and lots of minor
cleanup. Yaml conversions also continue to trickle in (plenty more to go!)
New device support
* ad7476
- Add ad7091 support (ID only)
* ad9467
- New driver for this 200/250 MSPS adi-axi-adc and SPI attached ADC.
* adi-axi-adc
- New driver to support ADIs generic AXI ADC IP core, used to provide
high speed interfaces to ADCs (JESD204B/C or parallel interfaces). Usually
paired with a device using a slow configuration interface (spi etc)
Includes DT bindings and some fixes for fpga headers.
* bmg160
- Add support for BMI088 (ID only)
* max1241
- New driver for this ADC.
* st_sensors
- Add support for LIS2HH12 accelerometer
* sx9310
- New driver supporting sx9310 and sx9311 proximity sensors.
Yaml DT binding conversions
* rockchip-saradc (including adding some missing parts)
* stm32-dac
* tsl2563
* vcnl4000
Features
* st_lsm6dsx
- Add LIS3MDL as a possible sensor hub device.
* vcnl4000
- Add new concept of near level (from DT) to provide to userspace which
often needs to have some calibrated concept of 'near'.
Cleanups, minor fixes etc.
* core
- Use snprintf for functions where strings are built and there is
potential for overflow.
- Correct docs to indicate mlock should not be used directly by drivers.
- Fix up accidental dropping of a patch to use bitmap_zalloc.
- Stop allowing enabling of buffers with no channels enabled.
- Drop unused 'stufftoread' from iio_buffer.
- Drop scan_el_attrs form iio_buffer as unused.
- Reorder sanity checks in __iio_device_register to fail earlier.
- Drop all the devm_ runregister / free functions from IIO as they
were never used and encourage poor design.
* dma-buffer
- Tidy up includes.
* dma-engine-buffer
- Provide dev-managed allocator.
- Fix an issue with printing a size_t
* cross subsystem (kxsd9, bmg160, mpu3050, bmi160, mpu6050, bmc150)
- Replace some unnecessary casts of error ptrs and whilst there.
use the %pe printf parameter to print them in a more useful fashion.
* cross subsystem
- Drop casts in calls to regmap_bulk_read as they make no sense.
- Use devm_platform_ioremap_resource to reduce boilerplate.
- Fix typos in Analog Devices.
* counters/104-quad
- Add Syed Nayyar Waris as an additional maintainer.
* ad7476
- Generate CONVST signal internally rather than requiring external
trigger. Add sysfs read back as can now do so.
- use devm_add_action_or_reset to tidy up error and remove handling.
* ad7793
- Switch to read_avail from explicit attribute. Mostly done to avoid
confusing people with a - sign (without surounding spaces) that
was correct but checkpatch didn't like.
* adis library
- Add missing newlines at end of error messages.
* adis16400
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* adis16460
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* ad_sigma_delta
- Move some channel definitions into individual drivers to avoid
having to deal with complex options.
* ak8974
- Silence an error on deffered probe.
* bmp280
- Harden against IRQ before registration.
- Convert to read_avail instead of opencoding the equivalent.
- Explicitly mark GPIO as optional.
- Cleanup casts.
- Remove line breaks from strings.
* htts221
- Replace direct access to platform_data with dev_get_platdata().
- Use device properties rather than device tree ones to allow ACPI
probing.
- Casting cleanups.
* intel_mrfld_adc
- Don't use unaligned accessor for aligned data.
* isl29125
- Reorder buer pre and post hooks to allow for coming core rework.
* ltc2983
- Remove comp to bool.
* max1363
- Stop using mlock from the iio_dev directly in favour of a local lock
with clearly defined scope.
* max30100
- Use generic device properties to allow ACPI probe.
* mpu6050
- Convert to i2c_new_client_device.
- Add debugfs register access.
* st_lsm6dsx
- Provide means of configuring full scale on slave device if supported.
- Drop include of st_sensors header to get one value. Its not otherwise
used by this driver.
* st-sensors
- Replace direct access to platform_data with dev_get_platdata().
- Casting cleanups.
- Avoid splitting strings.
* st_uvis25
- Casting cleanups.
* tsl2563
- Typo fix.
* tsl2772
- scnprintf in a non obvious string building usecase. Note also 'fixes'
a wrong calculation of remaining space that couldn't actually cause
any trouble as there was lots of room.
* xilinx-xadc
- Fix Lars-Peter spelling his own name wrong :) + additional typos.
* tag 'iio-for-5.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (101 commits)
iio: magnetometer: ak8974: Silence deferred-probe error
Documentation: ABI: document IIO in_proximity_nearlevel file
iio: vcnl4000: Export near level property for proximity sensor
dt-bindings: iio: light: vcnl4000: Add proximity-near-level
dt-bindings: iio: Introduce common properties for iio sensors
dt-bindings: iio: vcnl4000: convert bindings to YAML format
iio: Fix misspellings of "Analog Devices"
iio: light: isl29125: fix iio_triggered_buffer_{predisable,postenable} positions
iio: adc: fsl-imx25-gcq: Use devm_platform_ioremap_resource
iio: adc: at91-adc: Use devm_platform_ioremap_resource
iio: adc: sun4i-gpadc-iio: Use devm_platform_ioremap_resource
iio:light:ltr501: Drop unnecessary cast of parameter in regmap_bulk_read
iio:magn:mmc35240: Drop unnecessary casts of val parameter in regmap_bulk*
iio:imu:mpu6050: Tidy up parameters to regmap_bulk functions.
iio:chemical:bme680: Tidy up parameters to regmap_bulk_read
iio:chemical:atlas-sensor: Drop unnecessary explicit casts in regmap_bulk_read calls
iio:accel:mxc4005: Drop unnecessary explicit casts in regmap_bulk_read calls
iio: imu: st_lsm6dsx: drop huge include in sensor-hub driver
iio: buffer: drop devm_iio_kfifo_free() API call
iio: buffer: drop devm_iio_hw_consumer_free() API call
...
|
|
Add driver for the Maxim MAX1241 12-bit, single-channel ADC.
Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX1240-MAX1241.pdf
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Alexandru Lazar <alazar@startmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The AD9467 is a 16-bit, monolithic, IF sampling analog-to-digital converter
(ADC). It is optimized for high performanceover wide bandwidths and ease of
use. The product operates at a 250 MSPS conversion rate and is designed for
wireless receivers, instrumentation, and test equipment that require a high
dynamic range. The ADC requires 1.8 V and 3.3 V power supplies and a low
voltage differential input clock for full performance operation. No
external reference or driver components are required for many applications.
Data outputs are LVDS compatible (ANSI-644 compatible) and include the
means to reduce the overall current needed for short trace distances.
Since the chip can operate at such high sample-rates (much higher than
classical interfaces), it requires that a DMA controller be used to
interface directly to the chip and push data into memory.
Typically, the AXI ADC IP core is used to interface with it.
Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/AD9467.pdf
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This change adds support for the Analog Devices Generic AXI ADC IP core.
The IP core is used for interfacing with analog-to-digital (ADC) converters
that require either a high-speed serial interface (JESD204B/C) or a source
synchronous parallel interface (LVDS/CMOS).
Usually, some other interface type (i.e SPI) is used as a control interface
for the actual ADC, while the IP core (controlled via this driver), will
interface to the data-lines of the ADC and handle the streaming of data
into memory via DMA.
Because of this, the AXI ADC driver needs the other SPI-ADC driver to
register with it. The SPI-ADC needs to be register via the SPI framework,
while the AXI ADC registers as a platform driver. The two cannot be ordered
in a hierarchy as both drivers have their own registers, and trying to
organize this [in a hierarchy becomes] problematic when trying to map
memory/registers.
There are some modes where the AXI ADC can operate as standalone ADC, but
those will be implemented at a later point in time.
DocLink: https://wiki.analog.com/resources/fpga/docs/axi_adc_ip
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull mfd updates from Lee Jones:
"New Drivers:
- Add support for IQS620A/621/622/624/625 Azoteq IQS62X Sensors
New Device Support:
- Add support for ADC, IRQ, Regulator, RTC and WDT to Ricoh RN5T618 PMIC
- Add support for Comet Lake to Intel LPSS
New Functionality:
- Add support for Charger Detection to Spreadtrum SC27xx PMICs
- Add support for Interrupt Polarity to Dialog Semi DA9062/61 PMIC
- Add ACPI enumeration support to Diolan DLN2 USB Adaptor
Fix-ups:
- Device Tree; iqs62x, rn5t618, cros_ec_dev, stm32-lptimer, rohm,bd71837, rohm,bd71847
- I2C registration; rn5t618
- Kconfig; MFD_CPCAP, AB8500_CORE, MFD_WM8994, MFD_WM97xx, MFD_STPMIC1
- Use flexible-array members; omap-usb-tll, qcom-pm8xxx
- Remove unnecessary casts; omap-usb-host, omap-usb-tll
- Power (suspend/resume/poweroff) enhancements; rk808
- Improve error/sanity checking; dln2
- Use snprintf(); aat2870-core
Bug Fixes:
- Fix PCI IDs in intel-lpss-pci"
* tag 'mfd-next-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (33 commits)
mfd: intel-lpss: Fix Intel Elkhart Lake LPSS I2C input clock
mfd: aat2870: Use scnprintf() for avoiding potential buffer overflow
mfd: dln2: Allow to be enumerated via ACPI
mfd: da9062: Add support for interrupt polarity defined in device tree
dt-bindings: bd718x7: Yamlify and add BD71850
mfd: dln2: Fix sanity checking for endpoints
mfd: intel-lpss: Add Intel Comet Lake PCH-V PCI IDs
mfd: sc27xx: Add USB charger type detection support
dt-bindings: mfd: Document STM32 low power timer bindings
mfd: rk808: Convert RK805 to shutdown/suspend hooks
mfd: rk808: Reduce shutdown duplication
mfd: rk808: Stop using syscore ops
mfd: rk808: Ensure suspend/resume hooks always work
mfd: rk808: Always use poweroff when requested
mfd: omap: Remove useless cast for driver.name
mfd: Kconfig: Fix some misspelling of the word functionality
mfd: pm8xxx: Replace zero-length array with flexible-array member
mfd: omap-usb-tll: Replace zero-length array with flexible-array member
mfd: cpcap: Fix compile if MFD_CORE is not selected
mfd: cros_ec: Check DT node for usbpd-notify add
...
|
|
Both chips have an A/D converter capable of measuring
things like VBAT, VUSB and analog inputs.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Move ad7192 ADC driver out of staging into mainline.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This chip is similar to the LTC2497 ADC, it just uses SPI instead of I2C
and so has a slightly different protocol. Only the actual hardware
access is different. The spi protocol is different enough to not be able
to map the differences via a regmap.
Also generalize the entry in MAINTAINER to cover the newly introduced
file.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Ad7091R5 was added in a non alphabetical order after AD7124 in Makefile and
KConfig. This patch fixes that and place Ad7091R5 before AD7124.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
AD7091R5 is 4-Channel, I2C, Ultra Low Power,12-Bit ADC.
This driver will also support AD7091R2/4/8 in the future.
Datasheet:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ad7091r-5.pdf
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Co-developed-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The AD7292 is a 10-bit monitor and control system with ADC, DACs,
temperature sensor, and GPIOs.
Configure AD7292 devices in direct access mode, enabling single-ended
ADC readings.
Datasheet:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ad7292.pdf
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Immutable branch as considerable overlap with mfd, power and hwmon.
|
|
This is a new driver for the ST-Ericsson AB8500 GPADC, which
replaces the old driver in drivers/mfd/ab8500-gpadc.c and
thus gets rid of another necessarily different custom driver
from the times before IIO existed.
The AB8500 GPADC can convert 10 different channels and these
are used for monitoring voltages in the U8500 chipset, some
are used for battery charging, some for temperature
monitoring.
As this is very core functionality that a lot of drivers
depend on and was formerly compiled in with the AB8500 core
driver, we deafault it to 'y' in Kconfig: it can be compiled
out but it is really not advisible: the platform can
for example overheat if we do.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Exposes the ADC device present on, at least, Intel Merrifield platform.
Based on work done by:
Yang Bin <bin.yang@intel.com>
Huiquan Zhong <huiquan.zhong@intel.com>
Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Pavan Kumar S <pavan.kumar.s@intel.com>
Though it has been heavily rewritten for upstream.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Maxim's max12xx series is very similar to the max10xx series, with the
difference of the measurements depth which is upgraded from 10 to 12
bits per channel. Everything else looks the same.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
A driver for ADS1015 with more functionality is available in the iio
subsystem.
Remove the hwmon driver as duplicate. If the chip is used for hardware
monitoring, the iio->hwmon bridge should be used.
Cc: Dirk Eibach <eibach@gdsys.de>
Link: https://lore.kernel.org/r/1562004758-13025-1-git-send-email-linux@roeck-us.net
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO device support, features, cleanups and minor fixes for 5.3.
A few bits for the counters subsystem mixed in here as well.
There are some late breaking fixes as well, which aren't so urgent
they can't wait for the merge window.
New Device Support
* adf4371
- New driver + bindings.
- Support the adf4372 PLL. Mostly ID and bindings.
* ad8366 (note includes rework of driver needed to allow support for these).
- Support the ADL5240 variable gain amplifier (VGA).
- Support the ADA4961 digital gain amplifier (DGA).
* dps310
- New driver, in several parts from different authors for this temp
and pressure sensor.
- Includes errata workaround for a temperature reading issue.
* stk3310
- Support the stk3335, mostly ID.
Features and cleanups
* core
- drop error handling on debugfs registration.
- harden by making sure we don't overrun iio_chan_info_postfix.
* docs
- convert remaining docs to rst. At somepoint we'll fit these few
into the main IIO docs.
- improve sampling_frequency_available docs but explaining the
range form.
* ad_sigma_delta
- Drop a pointless goto.
* ad2s1210
- Drop pointless platform data null check seeing as we don't actually
use platform data anymore.
* ad7124
- Relax limitation on channel numbers to allow pseudo different channels.
- Support control of whether the input is buffered via DT.
- Use dynamic allocation for channel configuration to make it easier
to support new devices.
- YAML binding conversion.
* ad7150
- Comment tidy up.
- Consistent and simple if (ret) handling of i2c errors.
- FIELD_GET and GENMASK.
- Ternary rather than !!(condition) for readability.
- Use macros to avoid repetition of channel definitions.
* ad7606
- Add software channel config (rather that pin controlled)
- Refactor to simplify addition of new part in future.
* ad7746
- of_deivce_id table.
* ad7780
- MAINTAINERS entry
- YAML DT bindings.
* ad8366
- Stop using core mlock in favour of well scoped local lock.
- SPDX + copyright date update.
* ad9834
- of_device_id table
* adf4371
- Add support for output stage muting before lock on has occured.
* adis library
- MAINTAINERS entry to reflect that this now Alexandru's problem ;)
* adis162xx:
- Fix a slightly incorrect set of comments and print statements on
minimum supported voltage.
* adis16203
- of_device_id table.
* adis16240
- Add of_device_id table (in two parts as first patch only used it for
MODULE_DEVICE_TABLE.)
* adt7316-spi
- of_device_id table
* adxl372
- YAML DT binding conversion.
- Cleanup use of buffer callback functions (precursor to core rework).
* bh1710
- Simplify getting the i2c adapter from the client.
* dht11
- Mote to newer GPIO consumer interface.
* kxcjk-1013.c
- Add binding for sensor in display of some ultrabooks after userspace
tools updated for it not be a problem to report two similar sensors.
* imx7d
- drop unused variables.
- white space
- define instead of variable for clock frequency that is fixed.
- drop pointless error message.
* messon_saradc
- SPDX
* sps30
- MAINTAINERS entry
- YAML binding conversion.
* st_accel
- Tidy up ordering in various buffer related callbacks. This is
part of a long running effort to simplify the core code.
* stm32-dfsdm:
- Manage the resolution cleanly in triggerd modes.
- Add fast mode support which allows more flexible filter choices.
- Add a comment on the reason for a 16 bit record when technically
not 'required'.
* st_lsm6dsx
- Embed device name in the sensor_settings struct as i3c doesn't
have a convenient name field to use for this.
* xilinx-adc
- Relax constraints on supported platforms to reflect that this
can used with FPGAs on PCIe cards and hence many architectures.
* counters/ftm-quaddec
- Fix some formatting io MODULE_AUTHOR
- MAINTAINERS entry
Fixes
* tools
- fix incorrect handling of 32 bit channels.
* sca3000
- Potential endian bug that is unlikely to bite anyone (be64 host
seems unlikely for this old part).
* stm32-adc
- Add vdda-supply. On some boards it needs to be turned on to supply
the ADC. DT bindings included.
* stm32-dfsdm
- Fix output resolution to work with filter orders other than 3.
- Fix output datatype as it's signed and previously claimed not to be.
* tag 'iio-for-5.3b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (68 commits)
iio: iio-utils: Fix possible incorrect mask calculation
iio: frequency: adf4371: Add support for output stage mute
dt-bindings: iio: frequency: Add ADF4372 PLL documentation
iio: frequency: adf4371: Add support for ADF4372 PLL
dt-bindings: iio: adc: Add buffered input property
Convert AD7124 bindings documentation to YAML format.
iio: adc: ad7124: Shift to dynamic allocation for channel configuration
iio: adc: ad7124: Add buffered input support
iio: adc: ad7124: Remove input number limitation
MAINTAINERS: add ADIS IMU driver library entry
iio: adis162xx: fix low-power docs & reports
counter/ftm-quaddec: Add missing '>' in MODULE_AUTHOR
iio: core: no need to check return value of debugfs_create functions
docs: iio: convert to ReST
iio: adc: stm32-adc: add missing vdda-supply
dt-bindings: iio: adc: stm32: add missing vdda supply
iio: adc: stm32-dfsdm: add comment for 16 bits record
iio: adc: stm32-dfsdm: add fast mode support
iio: adc: stm32-dfsdm: manage data resolution in trigger mode
iio: adc: stm32-dfsdm: fix data type
...
|
|
Since the XADC logic can be used with standalone Xilinx FPGAs, this
driver can potentially be used with many different platforms, not just
the Zynq and MicroBlaze platforms this driver was allowed to be built
for. There should be no platform-specific code in this driver, so just
delete the platform dependency.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
