Age | Commit message (Collapse) | Author | Files | Lines |
|
The memory controller on Tegra132 is very similar to the one found on
Tegra124. But the Denver CPUs don't have an outer cache, so dcache
maintenance is done slightly differently.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Provide clients and swgroups files in debugfs. These files show for
which clients IOMMU translation is enabled and which ASID is associated
with each SWGROUP.
Cc: Hiroshi Doyu <hdoyu@nvidia.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Pull intel iommu updates from David Woodhouse:
"This lays a little of the groundwork for upcoming Shared Virtual
Memory support — fixing some bogus #defines for capability bits and
adding the new ones, and starting to use the new wider page tables
where we can, in anticipation of actually filling in the new fields
therein.
It also allows graphics devices to be assigned to VM guests again.
This got broken in 3.17 by disallowing assignment of RMRR-afflicted
devices. Like USB, we do understand why there's an RMRR for graphics
devices — and unlike USB, it's actually sane. So we can make an
exception for graphics devices, just as we do USB controllers.
Finally, tone down the warning about the X2APIC_OPT_OUT bit, due to
persistent requests. X2APIC_OPT_OUT was added to the spec as a nasty
hack to allow broken BIOSes to forbid us from using X2APIC when they
do stupid and invasive things and would break if we did.
Someone noticed that since Windows doesn't have full IOMMU support for
DMA protection, setting the X2APIC_OPT_OUT bit made Windows avoid
initialising the IOMMU on the graphics unit altogether.
This means that it would be available for use in "driver mode", where
the IOMMU registers are made available through a BAR of the graphics
device and the graphics driver can do SVM all for itself.
So they started setting the X2APIC_OPT_OUT bit on *all* platforms with
SVM capabilities. And even the platforms which *might*, if the
planets had been aligned correctly, possibly have had SVM capability
but which in practice actually don't"
* git://git.infradead.org/intel-iommu:
iommu/vt-d: support extended root and context entries
iommu/vt-d: Add new extended capabilities from v2.3 VT-d specification
iommu/vt-d: Allow RMRR on graphics devices too
iommu/vt-d: Print x2apic opt out info instead of printing a warning
iommu/vt-d: kill bogus ecap_niotlb_iunits()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"Not much this time, but the changes include:
- moving domain allocation into the iommu drivers to prepare for the
introduction of default domains for devices
- fixing the IO page-table code in the AMD IOMMU driver to correctly
encode large page sizes
- extension of the PCI support in the ARM-SMMU driver
- various fixes and cleanups"
* tag 'iommu-updates-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (34 commits)
iommu/amd: Correctly encode huge pages in iommu page tables
iommu/amd: Optimize amd_iommu_iova_to_phys for new fetch_pte interface
iommu/amd: Optimize alloc_new_range for new fetch_pte interface
iommu/amd: Optimize iommu_unmap_page for new fetch_pte interface
iommu/amd: Return the pte page-size in fetch_pte
iommu/amd: Add support for contiguous dma allocator
iommu/amd: Don't allocate with __GFP_ZERO in alloc_coherent
iommu/amd: Ignore BUS_NOTIFY_UNBOUND_DRIVER event
iommu/amd: Use BUS_NOTIFY_REMOVED_DEVICE
iommu/tegra: smmu: Compute PFN mask at runtime
iommu/tegra: gart: Set aperture at domain initialization time
iommu/tegra: Setup aperture
iommu: Remove domain_init and domain_free iommu_ops
iommu/fsl: Make use of domain_alloc and domain_free
iommu/rockchip: Make use of domain_alloc and domain_free
iommu/ipmmu-vmsa: Make use of domain_alloc and domain_free
iommu/shmobile: Make use of domain_alloc and domain_free
iommu/msm: Make use of domain_alloc and domain_free
iommu/tegra-gart: Make use of domain_alloc and domain_free
iommu/tegra-smmu: Make use of domain_alloc and domain_free
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups all over, although there are a few
items that sort of fall into the new feature category.
First off, we have new callbacks for PM domains that should help us to
handle some issues related to device initialization in a better way.
There also is some consolidation in the unified device properties API
area allowing us to use that inferface for accessing data coming from
platform initialization code in addition to firmware-provided data.
We have some new device/CPU IDs in a few drivers, support for new
chips and a new cpufreq driver too.
Specifics:
- Generic PM domains support update including new PM domain callbacks
to handle device initialization better (Russell King, Rafael J
Wysocki, Kevin Hilman)
- Unified device properties API update including a new mechanism for
accessing data provided by platform initialization code (Rafael J
Wysocki, Adrian Hunter)
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano)
- intel_idle update including support for the Silvermont Core in the
Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause)
- New cpufreq driver for Hisilicon ACPU (Leo Yan)
- intel_pstate update including support for the Knights Landing chip
(Dasaratharaman Chandramouli, Kristen Carlson Accardi)
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann)
- powernv cpufreq driver update (Shilpasri G Bhat)
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi)
- powercap RAPL (Running-Average Power Limit) driver update including
support for Intel Broadwell server chips (Jacob Pan, Mathias Krause)
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki)
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng)
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems and
a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede)
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu)
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki)
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu)
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu)
- Configurable delay for the system suspend/resume testing facility
(Brian Norris)
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki)"
* tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
ACPI / scan: Fix NULL pointer dereference in acpi_companion_match()
ACPI / scan: Rework modalias creation when "compatible" is present
intel_idle: mark cpu id array as __initconst
powercap / RAPL: mark rapl_ids array as __initconst
powercap / RAPL: add ID for Broadwell server
intel_pstate: Knights Landing support
intel_pstate: remove MSR test
cpufreq: fix qoriq uniprocessor build
ACPI / scan: Take the PRP0001 position in the list of IDs into account
ACPI / scan: Simplify acpi_match_device()
ACPI / scan: Generalize of_compatible matching
device property: Introduce firmware node type for platform data
device property: Make it possible to use secondary firmware nodes
PM / watchdog: iTCO: stop watchdog during system suspend
cpufreq: hisilicon: add acpu driver
ACPI / EC: Call acpi_walk_dep_device_list() after installing EC opregion handler
cpufreq: powernv: Report cpu frequency throttling
intel_idle: Add support for the Airmont Core in the Cherrytrail and Braswell SOCs
intel_idle: Update support for Silvermont Core in Baytrail SOC
PM / devfreq: tegra: Register governor on module init
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Enumeration
- Read capability list as dwords, not bytes (Sean O. Stalley)
Resource management
- Don't check for PNP overlaps with unassigned PCI BARs (Bjorn Helgaas)
- Mark invalid BARs as unassigned (Bjorn Helgaas)
- Show driver, BAR#, and resource on pci_ioremap_bar() failure (Bjorn Helgaas)
- Fail pci_ioremap_bar() on unassigned resources (Bjorn Helgaas)
- Assign resources before drivers claim devices (Yijing Wang)
- Claim bus resources before pci_bus_add_devices() (Yijing Wang)
Power management
- Optimize device state transition delays (Aaron Lu)
- Don't clear ASPM bits when the FADT declares it's unsupported (Matthew Garrett)
Virtualization
- Add ACS quirks for Intel 1G NICs (Alex Williamson)
IOMMU
- Add ptr to OF node arg to of_iommu_configure() (Murali Karicheri)
- Move of_dma_configure() to device.c to help re-use (Murali Karicheri)
- Fix size when dma-range is not used (Murali Karicheri)
- Add helper functions pci_get[put]_host_bridge_device() (Murali Karicheri)
- Add of_pci_dma_configure() to update DMA configuration (Murali Karicheri)
- Update DMA configuration from DT (Murali Karicheri)
- dma-mapping: limit IOMMU mapping size (Murali Karicheri)
- Calculate device DMA masks based on DT dma-range size (Murali Karicheri)
ARM Versatile host bridge driver
- Check for devm_ioremap_resource() failures (Jisheng Zhang)
Broadcom iProc host bridge driver
- Add Broadcom iProc PCIe driver (Ray Jui)
Marvell MVEBU host bridge driver
- Add suspend/resume support (Thomas Petazzoni)
Renesas R-Car host bridge driver
- Fix position of MSI enable bit (Nobuhiro Iwamatsu)
- Write zeroes to reserved PCIEPARL bits (Nobuhiro Iwamatsu)
- Change PCIEPARL and PCIEPARH to PCIEPALR and PCIEPAUR (Nobuhiro Iwamatsu)
- Verify that mem_res is 64K-aligned (Nobuhiro Iwamatsu)
Samsung Exynos host bridge driver
- Fix INTx enablement statement termination error (Jaehoon Chung)
Miscellaneous
- Make a shareable UUID for PCI firmware ACPI _DSM (Aaron Lu)
- Clarify policy for vendor IDs in pci.txt (Michael S. Tsirkin)"
* tag 'pci-v4.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (36 commits)
PCI: Read capability list as dwords, not bytes
PCI: layerscape: Simplify platform_get_resource_byname() failure checking
PCI: keystone: Don't dereference possible NULL pointer
PCI: versatile: Check for devm_ioremap_resource() failures
PCI: Don't clear ASPM bits when the FADT declares it's unsupported
PCI: Clarify policy for vendor IDs in pci.txt
PCI/ACPI: Optimize device state transition delays
PCI: Export pci_find_host_bridge() for use inside PCI core
PCI: Make a shareable UUID for PCI firmware ACPI _DSM
PCI: Fix typo in Thunderbolt kernel message
PCI: exynos: Fix INTx enablement statement termination error
PCI: iproc: Add Broadcom iProc PCIe support
PCI: iproc: Add DT docs for Broadcom iProc PCIe driver
PCI: Export symbols required for loadable host driver modules
PCI: Add ACS quirks for Intel 1G NICs
PCI: mvebu: Add suspend/resume support
PCI: Cleanup control flow
sparc/PCI: Claim bus resources before pci_bus_add_devices()
PCI: Assign resources before drivers claim devices (pci_scan_root_bus())
PCI: Fail pci_ioremap_bar() on unassigned resources
...
|
|
* device-properties:
device property: Introduce firmware node type for platform data
device property: Make it possible to use secondary firmware nodes
driver core: Implement device property accessors through fwnode ones
driver core: property: Update fwnode_property_read_string_array()
driver core: Add comments about returning array counts
ACPI: Introduce has_acpi_companion()
driver core / ACPI: Represent ACPI companions using fwnode_handle
|
|
and 'core' into next
Conflicts:
drivers/iommu/amd_iommu.c
drivers/iommu/tegra-gart.c
drivers/iommu/tegra-smmu.c
|
|
When a default page-size for given level should be mapped,
the level encoding must be 0 rather than 7. This fixes an
issue seen on IOMMUv2 hardware, where this encoding is
enforced.
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Now that fetch_pte returns the page-size of the pte, this
function can be optimized too.
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Now that fetch_pte returns the page-size of the pte, the
call in this function can also be optimized a little bit.
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Now that fetch_pte returns the page-size of the pte, this
function can be optimized a lot.
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Extend the fetch_pte function to also return the page-size
that is mapped by the returned pte.
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Add code to allocate memory from the contiguous memory
allocator to support coherent allocations larger than 8MB.
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Don't explicitly add __GFP_ZERO to the allocator flags.
Leave this up to the caller.
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Detaching a device from its domain at this event is
problematic for several reasons:
* The device might me in an alias group and
detaching it will also detach all other devices in
the group. This removes valid DMA mappings from
the other devices causing io-page-faults and lets
these devices fail.
* Devices might have unity mappings specified by the
IVRS table. These mappings are required for the
device even when no device driver is attached.
Detaching the device from its domain in driver
unbind will also remove these unity mappings.
This patch removes the handling of the BUS_NOTIFY_UNBOUND_DRIVER
event to prevent these issues and align it better with the
behavior of the VT-d driver.
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Use the new device-notifier event instead of the old
BUS_NOTIFY_DEL_DEVICE to make sure the device driver had a
chance to uninit the device before all its mappings are
teared down.
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The SMMU on Tegra30 and Tegra114 supports addressing up to 4 GiB of
physical memory. On Tegra124 the addressable physical memory was
extended to 16 GiB. The page frame number stored in PTEs therefore
requires 20 or 22 bits, depending on SoC generation.
In order to cope with this, compute the proper value at runtime.
Reported-by: Joseph Lo <josephl@nvidia.com>
Cc: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The aperture of the domain should always be available, otherwise drivers
need to attach first before they can use the aperture geometry.
Cc: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Each address space in the Tegra SMMU provides 4 GiB worth of addresses.
Cc: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
All drivers have been converted to the new domain_alloc and
domain_free iommu-ops. So remove the old ones and get rid of
iommu_domain->priv too, as this is no longer needed when the
struct iommu_domain is embedded in the private structures of
the iommu drivers.
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Implement domain_alloc and domain_free iommu-ops as a
replacement for domain_init/domain_destroy.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Implement domain_alloc and domain_free iommu-ops as a
replacement for domain_init/domain_destroy.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Implement domain_alloc and domain_free iommu-ops as a
replacement for domain_init/domain_destroy.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Implement domain_alloc and domain_free iommu-ops as a
replacement for domain_init/domain_destroy.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Implement domain_alloc and domain_free iommu-ops as a
replacement for domain_init/domain_destroy.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Implement domain_alloc and domain_free iommu-ops as a
replacement for domain_init/domain_destroy.
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Implement domain_alloc and domain_free iommu-ops as a
replacement for domain_init/domain_destroy.
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Implement domain_alloc and domain_free iommu-ops as a
replacement for domain_init/domain_destroy.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Implement domain_alloc and domain_free iommu-ops as a
replacement for domain_init/domain_destroy.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Implement the new domain_alloc and domain_free call-backs
and remove the old domain_init/destroy ones.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Get rid of domain_init and domain_destroy and implement
domain_alloc/domain_free instead.
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Implement the new iommu-ops function pointers and remove the
obsolete domain_init and domain_destroy functions.
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Check for the new __IOMMU_DOMAIN_PAGING flag before calling
into the iommu drivers ->map and ->unmap call-backs.
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This allows to handle domains differently based on their
type in the future. An IOMMU driver can implement certain
optimizations for DMA-API domains for example.
The domain types can be extended later and some of the
existing domain attributes can be migrated to become domain
flags.
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
These new call-backs defer the allocation and destruction of
'struct iommu_domain' to the iommu driver. This allows
drivers to embed this struct into their private domain
structures and to get rid of the domain_init and
domain_destroy call-backs when all drivers have been
converted.
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Although we set TCR.T1SZ to 0, the input address range covered by TTBR1
is actually calculated using T0SZ in this case on the ARM SMMU. This
could theoretically lead to speculative table walks through physical
address zero, leading to all sorts of fun and games if we have MMIO
regions down there.
This patch avoids the issue by setting EPD1 to disable walks through
the unused TTBR1 register.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
IOMMU groups for PCI devices can correspond to multiple DMA aliases due
to things like ACS and PCI quirks.
This patch extends the ARM SMMU ->add_device callback so that we
consider all of the DMA aliases for a PCI IOMMU group, rather than
creating a separate group for each Requester ID.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Since we use dma_map_page() as an architecture-independent means of
making page table updates visible to non-coherent SMMUs, we need to
have a suitable DMA mask set to discourage the DMA mapping layer from
creating bounce buffers and flushing those instead, if said page tables
happen to lie outside the default 32-bit mask.
Tested-by: Mitchel Humpherys <mitchelh@codeaurora.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
[will: added error checking]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The VMID16 (8.1) extension to SMMUv2 added a 16-bit VMID16 field to the
CBA2R registers. Unfortunately, if software writes this field as zero
after setting an 8-bit VMID in a stage-2 CBAR, then the VMID may also be
overwritten with zero on some early implementations (the architecture
was later updated to fix this issue).
This patch ensures that we initialise CBA2R before CBAR, therefore
ensuring that the VMID is set correctly.
Tested-by: Manish Jaggi <mjaggi@caviumnetworks.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Add a new function iommu_context_addr() which takes care of the
differences and returns a pointer to a context entry which may be
in either format. The formats are binary compatible for all the old
fields anyway; the new one is just larger and some of the reserved
bits in the original 128 are now meaningful.
So far, nothing actually uses the new fields in the extended context
entry. Modulo hardware bugs with interpreting the new-style tables,
this should basically be a no-op.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Commit c875d2c1 ("iommu/vt-d: Exclude devices using RMRRs from IOMMU API
domains") prevents certain options for devices with RMRRs. This even
prevents those devices from getting a 1:1 mapping with 'iommu=pt',
because we don't have the code to handle *preserving* the RMRR regions
when moving the device between domains.
There's already an exclusion for USB devices, because we know the only
reason for RMRRs there is a misguided desire to keep legacy
keyboard/mouse emulation running in some theoretical OS which doesn't
have support for USB in its own right... but which *does* enable the
IOMMU.
Add an exclusion for graphics devices too, so that 'iommu=pt' works
there. We should be able to successfully assign graphics devices to
guests too, as long as the initial handling of stolen memory is
reconfigured appropriately. This has certainly worked in the past.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@vger.kernel.org
|
|
BIOS can set up x2apic_opt_out bit on some platforms, for various misguided
reasons like insane SMM code with weird assumptions about what descriptors
look like, or wanting Windows not to enable the IOMMU so that the graphics
driver will take it over for SVM in "driver mode".
A user can either disable the x2apic_opt_out bit in BIOS or by kernel
parameter "no_x2apic_optout". Instead of printing a warning, we just
print information of x2apic opt out.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Unused after commit 71684406905f ("iommu/vt-d: Detach domain *only*
from attached iommus"). Reported by 0-day builder.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The of_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Device domains never span IOMMU hardware units, which allows the
domain ID space for each IOMMU to be an independent address space.
Therefore we can have multiple, independent domains, each with the
same domain->id, but attached to different hardware units. This is
also why we need to do a heavy-weight search for VM domains since
they can span multiple IOMMUs hardware units and we don't require a
single global ID to use for all hardware units.
Therefore, if we call iommu_detach_domain() across all active IOMMU
hardware units for a non-VM domain, the result is that we clear domain
IDs that are not associated with our domain, allowing them to be
re-allocated and causing apparent coherency issues when the device
cannot access IOVAs for the intended domain.
This bug was introduced in commit fb170fb4c548 ("iommu/vt-d: Introduce
helper functions to make code symmetric for readability"), but is
significantly exacerbated by the more recent commit 62c22167dd70
("iommu/vt-d: Fix dmar_domain leak in iommu_attach_device") which calls
domain_exit() more frequently to resolve a domain leak.
Fixes: fb170fb4c548 ("iommu/vt-d: Introduce helper functions to make code symmetric for readability")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: stable@vger.kernel.org # v3.17+
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This patch is a fix to "iommu/arm-smmu: add support for iova_to_phys
through ATS1PR".
According to ARM documentation, translation registers are optional even
in SMMUv1, so ID0_S1TS needs to be checked to verify their presence.
Also, we check that the domain is a stage-1 domain.
Signed-off-by: Baptiste Reynal <b.reynal@virtualopensystems.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
* pci/iommu:
of: Calculate device DMA masks based on DT dma-range size
arm: dma-mapping: limit IOMMU mapping size
PCI: Update DMA configuration from DT
of/pci: Add of_pci_dma_configure() to update DMA configuration
PCI: Add helper functions pci_get[put]_host_bridge_device()
of: Fix size when dma-range is not used
of: Move of_dma_configure() to device.c to help re-use
of: iommu: Add ptr to OF node arg to of_iommu_configure()
* pci/resource:
PCI: Fail pci_ioremap_bar() on unassigned resources
PCI: Show driver, BAR#, and resource on pci_ioremap_bar() failure
PCI: Mark invalid BARs as unassigned
PNP: Don't check for overlaps with unassigned PCI BARs
|
|
Now that the ACPI companions of devices are represented by pointers
to struct fwnode_handle, it is not quite efficient to check whether
or not an ACPI companion of a device is present by evaluating the
ACPI_COMPANION() macro.
For this reason, introduce a special static inline routine for that,
has_acpi_companion(), and update the code to use it where applicable.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
"pasid_state->device_state" and "dev_state" are the same, but it's nicer
to use dev_state consistently.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|