summaryrefslogtreecommitdiff
path: root/drivers/mfd/stmpe.h
AgeCommit message (Collapse)AuthorFilesLines
2016-08-10mfd: Add STMPE1600 supportPatrice Chotard1-0/+21
STMPE1600 is a 16-bit port expander. Datasheet is available here : http://www2.st.com/content/st_com/en/products/interfaces-and-transceivers/ i-o-expanders-and-level-translators/i-o-expanders/stmpe1600.html Signed-off-by: Amelie DELAUNAY <amelie.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-08-10mfd: stmpe: Rework registers accessPatrice Chotard1-6/+43
this update allows to use registers map as following : regs[reg_index + offset] instead of regs[reg_index] + offset This makes code clearer and will facilitate the addition of STMPE1600 on which LSB and MSB registers are respectively located at addr and addr + 1. Despite for all others STMPE variant, LSB and MSB registers are respectively located in reverse order at addr + 1 and addr. For variant which have 3 registers's bank, we use LSB,CSB and MSB indexes which contains respectively LSB (or LOW), CSB (or MID) and MSB (or HIGH) register addresses (STMPE1801/STMPE24xx). For variant which have 2 registers's bank, we use LSB and CSB indexes only. In this case the CSB index contains the MSB regs address (STMPE 1601). Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-08-10mfd: stmpe: Use generic bit mask namePatrice Chotard1-4/+2
In order to prepare the ground to STMPE1600, as STMPE1600's SYS_CTRL register has the same layout as STMPE801 variant, unify STMPExxx_REG_SYS_CTRL_RESET/INT_EN/INT_HI bit masks to more generic STMPE_SYS_CTRL_RESET/INT_EN/INT_HI Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-08-10mfd: stmpe: Add reset support for all STMPE variantPatrice Chotard1-2/+5
Reset was only implemented for STMPE1801 variant despite all variant have a SOFT_RESET bit. For STMPE2401/2403/801/1601/1801 SOFT_RESET bit is bit 7 of SYS_CTRL register. For STMPE610/811 (which have the same variant id) SOFT_RESET bit is bit 1 of SYS_CTRL register. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-08-10mfd: stmpe: Add STMPE_IDX_SYS_CTRL/2 enumPatrice Chotard1-0/+2
As STMPE1801/1601/24xx has a SYS_CTRL register and STMPE1601/2403 has even a SYS_CTRL2 register, add STMPE_IDX_SYS_CTRL/2 and update driver code accordingly This update prepares the ground for not yet supported STMPE1600 which share similar REG_SYS_CTRL register. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-12-31Merge branch 'for-linus' of ↵Linus Torvalds1-0/+3
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input layer fixes from Dmitry Torokhov: "Fixes for v7 protocol for ALPS devices and few other driver fixes. Also users can request input events to be stamped with boot time timestamps, in addition to real and monotonic timestamps" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: hil_kbd - fix incorrect use of init_completion Input: alps - v7: document the v7 touchpad packet protocol Input: alps - v7: fix finger counting for > 2 fingers on clickpads Input: alps - v7: sometimes a single touch is reported in mt[1] Input: alps - v7: ignore new packets Input: evdev - add CLOCK_BOOTTIME support Input: psmouse - expose drift duration for IBM trackpoints Input: stmpe - bias keypad columns properly Input: stmpe - enforce device tree only mode mfd: stmpe: add pull up/down register offsets for STMPE Input: optimize events_per_packet count calculation Input: edt-ft5x06 - fixed a macro coding style issue Input: gpio_keys - replace timer and workqueue with delayed workqueue Input: gpio_keys - allow separating gpio and irq in device tree
2014-12-16mfd: stmpe: add pull up/down register offsets for STMPELinus Walleij1-0/+3
This adds the register offsets for pull up/down for the STMPE 1601, 1801 and 24xx expanders. This is used to bias GPIO lines and keypad lines. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2014-11-10mfd: stmpe: Fix STMPE24xx GPMR LSBLinus Walleij1-1/+1
The least significat byte of the GPIO value read register on the STMPE24xx series is on addres 0xA4 not 0xA5. Correct against datasheet and tested on the STMPE2401 hardware. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-09mfd: stmpe: Rid data size incompatibility warn when building for 64bitLee Jones1-1/+1
Extinguishes: ../drivers/mfd/stmpe-i2c.c: In function ‘stmpe_i2c_probe’: ../drivers/mfd/stmpe-i2c.c:88:13: warning: cast from pointer to integer of different size partnum = (int)of_id->data; Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-05-09mfd: stmpe: mask off unused blocks properlyLinus Walleij1-1/+1
The STMPE driver would just read/modify/write the system control register on the STMPE1601, meaning it would not properly mask off the PWM block, which remained active if it was on at boot time. This makes sure the blocks are always masked off if they were active on boot, saving some power. Also rename the inconsistenty named STMPE1601 define for the PWM block activation. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-01-06mfd: stmicro: Constify struct mfd_cell where possibleGeert Uytterhoeven1-1/+1
As of commit 03e361b25ee8dfb1fd9b890072c23c4aae01c6c7 ("mfd: Stop setting refcounting pointers in original mfd_cell arrays"), the "cell" parameter of mfd_add_devices() is "const" again. Hence make all cell data passed to mfd_add_devices() const where possible. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-04-09mfd: support stmpe1801 18 bits enhanced port expanderJean-Nicolas Graux1-0/+49
Provides support for 1801 variant of stmpe gpio port expanders. This chip has 18 gpios configurable as GPI, GPO, keypad matrix, special key or dedicated key function. Note that special/dedicated key function is not supported yet. Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@stericsson.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-01-09mfd: Add support for stmpe variant 801Viresh Kumar1-0/+19
STMPE801 is a GPIO expander. Registers for 801 are much different from other variants. This patch adds support for STMPE801 in stmpe mfd driver. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com> Signed-off-by: Pratyush Anand <pratyush.anand@st.com> Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-01-09mfd: Add support for STMPE SPI interfaceViresh Kumar1-0/+1
Few STMPE controller can have register interface over SPI or I2C. Current implementation only supports I2C. This patch adds support for SPI interface for accessing STMPE's address space. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-01-09mfd: Separate out STMPE controller and interface specific codeViresh Kumar1-0/+33
Few STMPE controller can have register interface over SPI or I2C. Current implementation only supports I2C and all code is present in a single file stmpe.c. It would be better to separate out I2C interface specific code from controller specific code. Later SPI specific code can be added in a separate file. This patch separates out I2C and controller specific code into separate files, making stmpe.c independent of I2C. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-08-01mfd: Fix missing stmpe kerneldocOm Prakash1-0/+1
Generating kerneldoc for STMPE result in warnings, so fix this by adding missing documentation. Signed-off-by: Om Prakash <omprakash.pal@stericsson.com> Reviewed-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-08-12mfd: Add stmpe auto sleep featureSundar R Iyer1-0/+7
Some STMPE devices support entering sleep mode automatically on a specified timeout of inactivity on the I2C bus with the host system. Acked-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-08-12mfd: Add STMPE I/O Expander supportRabin Vincent1-0/+176
Add support for the STMPE family of I/O Expanders from STMicroelectronics. These devices include upto 24 gpios and a varying selection of blocks, including PWM, keypad, and touchscreen controllers. This patch adds the MFD core. [l.fu@pengutronix.de: fix stmpe811 enable hook] [l.fu@pengutronix.de: add touchscreen platform data] Acked-by: Luotao Fu <l.fu@pengutronix.de> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>