Age | Commit message (Collapse) | Author | Files | Lines |
|
Turning on CONFIG_DMA_API_DEBUG_SG results in the following warning:
DMA-API: mmci-pl18x 48220000.mmc: cacheline tracking EEXIST,
overlapping mappings aren't supported
WARNING: CPU: 1 PID: 51 at kernel/dma/debug.c:568
add_dma_entry+0x234/0x2f4
Modules linked in:
CPU: 1 PID: 51 Comm: kworker/1:2 Not tainted 6.1.28 #1
Hardware name: STMicroelectronics STM32MP257F-EV1 Evaluation Board (DT)
Workqueue: events_freezable mmc_rescan
Call trace:
add_dma_entry+0x234/0x2f4
debug_dma_map_sg+0x198/0x350
__dma_map_sg_attrs+0xa0/0x110
dma_map_sg_attrs+0x10/0x2c
sdmmc_idma_prep_data+0x80/0xc0
mmci_prep_data+0x38/0x84
mmci_start_data+0x108/0x2dc
mmci_request+0xe4/0x190
__mmc_start_request+0x68/0x140
mmc_start_request+0x94/0xc0
mmc_wait_for_req+0x70/0x100
mmc_send_tuning+0x108/0x1ac
sdmmc_execute_tuning+0x14c/0x210
mmc_execute_tuning+0x48/0xec
mmc_sd_init_uhs_card.part.0+0x208/0x464
mmc_sd_init_card+0x318/0x89c
mmc_attach_sd+0xe4/0x180
mmc_rescan+0x244/0x320
DMA API debug brings to light leaking dma-mappings as dma_map_sg and
dma_unmap_sg are not correctly balanced.
If an error occurs in mmci_cmd_irq function, only mmci_dma_error
function is called and as this API is not managed on stm32 variant,
dma_unmap_sg is never called in this error path.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Fixes: 46b723dd867d ("mmc: mmci: add stm32 sdmmc variant")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240207143951.938144-1-christophe.kerello@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The ux500 variant doesn't have a HW based timeout to use for busy-end IRQs.
To avoid hanging and waiting for the card to stop signaling busy, let's
schedule a delayed work, according to the corresponding cmd->busy_timeout
for the command. If the work gets to run, let's kick the IRQ handler to
complete the currently running request/command.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20230620091113.33393-1-ulf.hansson@linaro.org
|
|
On STM32MP25, the delay block is inside the SoC, and configured through
the SYSCFG registers. The algorithm is also different from what was in
STM32MP1 chip.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20230619115120.64474-7-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Create an sdmmc_tuning_ops struct to ease support for another
delay block peripheral.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20230619115120.64474-6-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In stm32 sdmmc variant revision v3.0, a block gap hardware flow control
should be used with bus speed modes SDR104 and HS200.
It is enabled by writing a non-null value to the new added register
MMCI_STM32_FIFOTHRR.
The threshold will be 2^(N-1) bytes, so we can use the ffs() function to
compute the value N to be written to the register. The threshold used
should be the data block size, but must not be bigger than the FIFO size.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20230619115120.64474-5-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The alignment for the IDMA size depends on the peripheral version, it
should then be configurable. Add stm32_idmabsize_align in the variant
structure.
And remove now unused (and wrong) MMCI_STM32_IDMABNDT_* macros.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20230619115120.64474-3-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The feedback clock is used only for SDR104 & HS200 modes, and when
delay block is used (frequency is higher than 50 MHz). The tuning
procedure is then only required for those modes. Skip the procedure
for other modes.
The setting of this feedback clock is done just after enabling delay
block, and before configuring it.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Link: https://lore.kernel.org/r/20230613150148.429828-1-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In SDIO mode, the sg list for requests can be unaligned with what the
STM32 SDMMC internal DMA can support. In that case, instead of failing,
use a temporary bounce buffer to copy from/to the sg list.
This buffer is limited to 1MB. But for that we need to also limit
max_req_size to 1MB. It has not shown any throughput penalties for
SD-cards or eMMC.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20220328145114.334577-1-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use sg and not data->sg when checking sg list elements. Else only the
first element alignment is checked.
The last element should be checked the same way, for_each_sg already set
sg to sg_next(sg).
Fixes: 46b723dd867d ("mmc: mmci: add stm32 sdmmc variant")
Cc: stable@vger.kernel.org
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20220317111944.116148-2-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use feedback clock for HS200 mode, as for SDR104.
The HS200 mode can be enabled through DT by using mmc-hs200-1_8v.
It is possible to use it on STM32MP13, but not STM32MP15 platforms.
Signed-off-by: Ludovic Barre <ludovic.barre@foss.st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211215141727.4901-5-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
During test campaign, and especially after several unbind/bind sequences,
it has been seen that the SD-card on SDMMC1 thread could freeze.
The freeze always appear on a CMD23 following a CMD19.
Checking SDMMC internal registers shows that the tuning command (CMD19)
has failed.
The freeze is then due to the delay block involved in the tuning sequence.
To correct this, clear the delay block register DLYB_CR register after
the tuning commands.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 1103f807a3b9 ("mmc: mmci_sdmmc: Add execute tuning with delay block")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211215141727.4901-4-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If the card has not been power cycled, it may still be using 1.8V
signaling. This situation is detected in mmc_sd_init_card function and
should be handled in mmci stm32 variant. The host->pwr_reg variable is
also correctly protected with spin locks.
Fixes: 94b94a93e355 ("mmc: mmci_sdmmc: Implement signal voltage callbacks")
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210701143353.13188-1-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Turning on CONFIG_DMA_API_DEBUG_SG results in the following warning:
WARNING: CPU: 1 PID: 85 at kernel/dma/debug.c:1302
debug_dma_map_sg+0x2a0/0x3cc mmci-pl18x 58005000.sdmmc: DMA-API: mapping sg
segment longer than device claims to support [len=126976] [max=65536]
dma api debug checks and compares the segment size to dma_get_max_seg_size
(dev->dma_parms->max_segment_size), the sdmmc variant has an internal DMA
and should define its max_segment_size constraint to avoid this warning.
This Patch defines the dev->dma_parms->max_segment_size with the constraint
already set for mmc core (host->mmc->max_seg_size).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200526155103.12514-3-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Turning on CONFIG_DMA_API_DEBUG_SG results in the following warning:
WARNING: CPU: 1 PID: 20 at kernel/dma/debug.c:500 add_dma_entry+0x16c/0x17c
DMA-API: exceeded 7 overlapping mappings of cacheline 0x031d2645
Modules linked in:
CPU: 1 PID: 20 Comm: kworker/1:1 Not tainted 5.5.0-rc2-00021-gdeda30999c2b-dirty #49
Hardware name: STM32 (Device Tree Support)
Workqueue: events_freezable mmc_rescan
[<c03138c0>] (unwind_backtrace) from [<c030d760>] (show_stack+0x10/0x14)
[<c030d760>] (show_stack) from [<c0f2eb28>] (dump_stack+0xc0/0xd4)
[<c0f2eb28>] (dump_stack) from [<c034a14c>] (__warn+0xd0/0xf8)
[<c034a14c>] (__warn) from [<c034a530>] (warn_slowpath_fmt+0x94/0xb8)
[<c034a530>] (warn_slowpath_fmt) from [<c03bca0c>] (add_dma_entry+0x16c/0x17c)
[<c03bca0c>] (add_dma_entry) from [<c03bdf54>] (debug_dma_map_sg+0xe4/0x3d4)
[<c03bdf54>] (debug_dma_map_sg) from [<c0d09244>] (sdmmc_idma_prep_data+0x94/0xf8)
[<c0d09244>] (sdmmc_idma_prep_data) from [<c0d05a2c>] (mmci_prep_data+0x2c/0xb0)
[<c0d05a2c>] (mmci_prep_data) from [<c0d073ec>] (mmci_start_data+0x134/0x2f0)
[<c0d073ec>] (mmci_start_data) from [<c0d078d0>] (mmci_request+0xe8/0x154)
[<c0d078d0>] (mmci_request) from [<c0cecb44>] (mmc_start_request+0x94/0xbc)
DMA api debug brings to light leaking dma-mappings, dma_map_sg and
dma_unmap_sg are not correctly balanced.
If a request is prepared, the dma_map/unmap are done in asynchronous call
pre_req (prep_data) and post_req (unprep_data). In this case the
dma-mapping is right balanced.
But if the request was not prepared, the data->host_cookie is define to
zero and the dma_map/unmap must be done in the request. The dma_map is
called by mmci_dma_start (prep_data), but there is no dma_unmap in this
case.
This patch adds dma_unmap_sg when the dma is finalized and the data cookie
is zero (request not prepared).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200526155103.12514-2-ludovic.barre@st.com
Fixes: 46b723dd867d ("mmc: mmci: add stm32 sdmmc variant")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch fix a power-on issue, and avoid to retry the power sequence.
In power off sequence: sdmmc must set pwr_reg in "power-cycle" state
(value 0x2), to prevent the card from being supplied through the signal
lines (all the lines are driven low).
In power on sequence: when the power is stable, sdmmc must set pwr_reg
in "power-off" state (value 0x0) to drive all signal to high before to
set "power-on".
To avoid writing the same value to the power register several times, this
register is cached by the pwr_reg variable. At probe pwr_reg is initialized
to 0 by kzalloc of mmc_alloc_host.
Like pwr_reg value is 0 at probing, the power on sequence fail because
the "power-off" state is not writes (value 0x0) and the lines
remain drive to low.
This patch initializes "pwr_reg" variable with power register value.
This it done in sdmmc variant init to not disturb default mmci behavior.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200420161831.5043-1-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The busyd0 line transition can be very fast. The busy request may be
completed by busy_d0end, without waiting for the busy_d0 steps. Therefore,
clear the busyd0end irq flag, even if no busy_status.
Fixes: 0e68de6aa7b1 ("mmc: mmci: sdmmc: add busy_complete callback")
Cc: stable@vger.kernel.org
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200325143409.13005-2-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
To prepare the voltage switch procedure, the VSWITCHEN bit must be set
before sending the CMD11. To confirm completion of voltage switch, the
VSWEND flag must be checked.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200128090636.13689-9-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The hardware delay block is used to align the sampling clock on the data
received by SDMMC. It is mandatory for SDMMC to support the SDR104 mode.
The delay block is used to generate an output clock which is dephased from
the input clock. The phase of the output clock must be programmed by the
execute tuning interface.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200128090636.13689-7-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch renames sdmmc_priv struct to sdmmc_idma which is assigned to
host->dma_priv.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200128090636.13689-3-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
sg_dma_xxx should be used after a dma_map_sg call has been done to get bus
addresses of each of the SG entries and their lengths. But mmci_host_ops
validate_data can be called before dma_map_sg. This patch replaces theses
macros by sg->offset and sg->length which are always defined.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200128090636.13689-2-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Make sdmmc_idma_validate_data to avoid the following warning
from sparse:
drivers/mmc/host/mmci_stm32_sdmmc.c:28:5: warning: symbol 'sdmmc_idma_validate_data' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adds a specific busy_complete callback for sdmmc variant.
sdmmc has 2 status flags:
-busyd0: This is a hardware status flag (inverted value of d0 line).
it does not generate an interrupt.
-busyd0end: This indicates only end of busy following a CMD response.
On busy to Not busy changes, an interrupt is generated (if unmask)
and BUSYD0END status flag is set. Status flag is cleared by writing
corresponding interrupt clear bit in MMCICLEAR.
The legacy busy completion has no dedicated interrupt for the end
of busy, so it's must monitor step by step the busy progression.
On sdmmc variant, this procedure is not needed, it's just need
to wait the busyd0end interrupt.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch defines get_dctrl_cfg callback for sdmmc variant.
sdmmc variant has specific stm32 transfer modes.
sdmmc data transfer mode selection could be:
-Block data transfer ending on block count.
-SDIO multibyte data transfer.
-MMC Stream data transfer (not used).
-Block data transfer ending with STOP_TRANSMISSION command.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adds a stm32 sdmmc variant, rev 1.1.
Introduces a new Manufacturer id "0x53, ascii 'S' to define
new stm32 sdmmc family with clean range of amba
revision/configurations bits (corresponding to sdmmc_ver
register with major/minor fields).
Add 2 variants properties:
-dma_lli, to enable link list support.
-stm32_idmabsize_mask, defines the range of SDMMC_IDMABSIZER register
which specify the number bytes per buffer.
DT properties for sdmmc:
-Indicate signal directions (only one property
for d0dir, d123dir, cmd_dir)
-Select command and data phase relation.
-Select "clock in" from an external driver.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|