| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 55c421b364482b61c4c45313a535e61ed5ae4ea3 ]
Using __exit for the remove function results in the remove callback being
discarded with CONFIG_MMC_DAVINCI=y. When such a device gets unbound (e.g.
using sysfs or hotplug), the driver is just removed without the cleanup
being performed. This results in resource leaks. Fix it by compiling in the
remove callback unconditionally.
This also fixes a W=1 modpost warning:
WARNING: modpost: drivers/mmc/host/davinci_mmc: section mismatch in
reference: davinci_mmcsd_driver+0x10 (section: .data) ->
davinci_mmcsd_remove (section: .exit.text)
Fixes: b4cff4549b7a ("DaVinci: MMC: MMC/SD controller driver for DaVinci family")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240324114017.231936-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
T100TA
commit 431946c0f640c93421439a6c928efb3152c035a4 upstream.
The card-detect GPIO for the microSD slot on Asus T100TA / T100TAM models
stopped working under Linux after commit 6fd03f024828 ("gpiolib: acpi:
support bias pull disable").
The GPIO in question is connected to a mechanical switch in the slot
which shorts the pin to GND when a card is inserted.
The GPIO pin correctly gets configured with a 20K pull-up by the BIOS,
but there is a bug in the DSDT where the GpioInt for the card-detect is
configured with a PullNone setting:
GpioInt (Edge, ActiveBoth, SharedAndWake, PullNone, 0x2710,
"\\_SB.GPO0", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0026
}
Linux now actually honors the PullNone setting and disables the 20K pull-up
configured by the BIOS.
Add a new DMI_QUIRK_SD_CD_ENABLE_PULL_UP quirk which when set calls
mmc_gpiod_set_cd_config() to re-enable the pull-up and set this for
the Asus T100TA models to fix this.
Fixes: 6fd03f024828 ("gpiolib: acpi: support bias pull disable")
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-7-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ef3eab75e17191e5665f52e64e85bc29d5705a7b upstream.
On the Toshiba WT10-A the microSD slot always reports the card being
write-protected, just like on the Toshiba WT8-B.
Add a DMI quirk to work around this.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-6-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f3521d7cbaefff19cc656325787ed797e5f6a955 upstream.
The Lenovo Yoga Tablet 2 Pro 1380 sdcard slot has an active high cd pin
and a broken wp pin which always reports the card being write-protected.
Add a DMI quirk to address both issues.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-5-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a92a73b1d9249d155412d8ac237142fa716803ea upstream.
Sort the DMI quirks alphabetically.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-4-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b3855668d98cf9c6aec2db999dd27d872f8ba878 upstream.
Most Bay Trail devices do not enable UHS modes for the external sdcard slot
the Lenovo Yoga Tablet 2 830 / 1050 and Lenovo Yoga Tablet 2 Pro 1380 (8",
10" and 13") models however do enable this.
Using a UHS cards in these tablets results in errors like this one:
[ 225.272001] mmc2: Unexpected interrupt 0x04000000.
[ 225.272024] mmc2: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 225.272034] mmc2: sdhci: Sys addr: 0x0712c400 | Version: 0x0000b502
[ 225.272044] mmc2: sdhci: Blk size: 0x00007200 | Blk cnt: 0x00000007
[ 225.272054] mmc2: sdhci: Argument: 0x00000000 | Trn mode: 0x00000023
[ 225.272064] mmc2: sdhci: Present: 0x01e20002 | Host ctl: 0x00000016
[ 225.272073] mmc2: sdhci: Power: 0x0000000f | Blk gap: 0x00000000
[ 225.272082] mmc2: sdhci: Wake-up: 0x00000000 | Clock: 0x00000107
[ 225.272092] mmc2: sdhci: Timeout: 0x0000000e | Int stat: 0x00000001
[ 225.272101] mmc2: sdhci: Int enab: 0x03ff000b | Sig enab: 0x03ff000b
[ 225.272110] mmc2: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000001
[ 225.272119] mmc2: sdhci: Caps: 0x076864b2 | Caps_1: 0x00000004
[ 225.272129] mmc2: sdhci: Cmd: 0x00000c1b | Max curr: 0x00000000
[ 225.272138] mmc2: sdhci: Resp[0]: 0x00000c00 | Resp[1]: 0x00000000
[ 225.272147] mmc2: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000900
[ 225.272155] mmc2: sdhci: Host ctl2: 0x0000000c
[ 225.272164] mmc2: sdhci: ADMA Err: 0x00000003 | ADMA Ptr: 0x0712c200
[ 225.272172] mmc2: sdhci: ============================================
which results in IO errors leading to issues accessing the sdcard.
0x04000000 is a so-called "Tuning Error" which sofar the SDHCI driver
does not support / enable. Modify the IRQ handler to process these.
This fixes UHS microsd cards not working with these tablets.
Link: https://lore.kernel.org/r/199bb4aa-c6b5-453e-be37-58bbf468800c@intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-3-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 63a7cd660246aa36af263b85c33ecc6601bf04be upstream.
Some mmc host drivers may need to fixup a card-detection GPIO's config
to e.g. enable the GPIO controllers builtin pull-up resistor on devices
where the firmware description of the GPIO is broken (e.g. GpioInt with
PullNone instead of PullUp in ACPI DSDT).
Since this is the exception rather then the rule adding a config
parameter to mmc_gpiod_request_cd() seems undesirable, so instead
add a new mmc_gpiod_set_cd_config() function. This is simply a wrapper
to call gpiod_set_config() on the card-detect GPIO acquired through
mmc_gpiod_request_cd().
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-2-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 67380251e8bbd3302c64fea07f95c31971b91c22 upstream.
Requesting a retune before switching to the RPMB partition has been
observed to cause CRC errors on the RPMB reads (-EILSEQ).
Since RPMB reads can not be retried, the clients would be directly
affected by the errors.
This commit disables the retune request prior to switching to the RPMB
partition: mmc_retune_pause() no longer triggers a retune before the
pause period begins.
This was verified with the sdhci-of-arasan driver (ZynqMP) configured
for HS200 using two separate eMMC cards (DG4064 and 064GB2). In both
cases, the error was easy to reproduce triggering every few tenths of
reads.
With this commit, systems that were utilizing OP-TEE to access RPMB
variables will experience an enhanced performance. Specifically, when
OP-TEE is configured to employ RPMB as a secure storage solution, it not
only writes the data but also the secure filesystem within the
partition. As a result, retrieving any variable involves multiple RPMB
reads, typically around five.
For context, on ZynqMP, each retune request consumed approximately
8ms. Consequently, reading any RPMB variable used to take at the very
minimum 40ms.
After droping the need to retune before switching to the RPMB partition,
this is no longer the case.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Acked-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240103112911.2954632-1-jorge@foundries.io
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d3182932bb070e7518411fd165e023f82afd7d25 ]
While STRB is currently used for DATA and CRC responses, the CMD
responses from the device to the host still require ITAPDLY for
HS400 timing.
Currently what is stored for HS400 is the ITAPDLY from High Speed
mode which is incorrect. The ITAPDLY for HS400 speed mode should
be the same as ITAPDLY as HS200 timing after tuning is executed.
Add the functionality to save ITAPDLY from HS200 tuning and save
as HS400 ITAPDLY.
Fixes: a161c45f2979 ("mmc: sdhci_am654: Enable DLL only for some speed modes")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-8-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9dff65bb5e09903c27d9cff947dff4d22b6ea6a1 ]
Add ITAPDLYSEL to sdhci_j721e_4bit_set_clock function.
This allows to set the correct ITAPDLY for timings that
do not carry out tuning.
Fixes: 1accbced1c32 ("mmc: sdhci_am654: Add Support for 4 bit IP on J721E")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-7-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 387c1bf7dce0dfea02080c8bdb066b5209e92155 ]
Currently the OTAP/ITAP delay enable functionality is incorrect in
the am654_set_clock function. The OTAP delay is not enabled when
timing < SDR25 bus speed mode. The ITAP delay is not enabled for
timings that do not carry out tuning.
Add this OTAP/ITAP delay functionality according to the datasheet
[1] OTAPDLYENA and ITAPDLYENA for MMC0.
[1] https://www.ti.com/lit/ds/symlink/am62p.pdf
Fixes: 8ee5fc0e0b3b ("mmc: sdhci_am654: Update OTAPDLY writes")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-4-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5cb2f9286a31f33dc732c57540838ad9339393ab ]
ti,otap-del-sel has been deprecated since v5.7 and there are no users of
this property and no documentation in the DT bindings either.
Drop the fallback code looking for this property, this makes
sdhci_am654_get_otap_delay() much easier to read as all the TAP values
can be handled via a single iterator loop.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20231122060215.2074799-1-vigneshr@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Stable-dep-of: 387c1bf7dce0 ("mmc: sdhci_am654: Add OTAP/ITAP delay enable")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d465234493bb6ad1b9c10a0c9ef9881b8d85081a ]
For DDR52 timing, DLL is enabled but tuning is not carried
out, therefore the ITAPDLY value in PHY CTRL 4 register is
not correct. Fix this by writing ITAPDLY after enabling DLL.
Fixes: a161c45f2979 ("mmc: sdhci_am654: Enable DLL only for some speed modes")
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-3-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6231d99dd4119312ad41abf9383e18fec66cbe4b ]
Currently the sdhci_am654 driver only supports one tuning
algorithm which should be used only when DLL is enabled. The
ITAPDLY is selected from the largest passing window and the
buffer is viewed as a circular buffer.
The new algorithm should be used when the delay chain
is enabled. The ITAPDLY is selected from the largest passing
window and the buffer is not viewed as a circular buffer.
This implementation is based off of the following paper: [1].
Also add support for multiple failing windows.
[1] https://www.ti.com/lit/an/spract9/spract9.pdf
Fixes: 13ebeae68ac9 ("mmc: sdhci_am654: Add support for software tuning")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-2-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 77e01b49e35f24ebd1659096d5fc5c3b75975545 upstream.
During the initialization to HS400es stage, add a HS400 tuning flow as an
optional process. For Mediatek IP, the HS400es mode requires a specific
tuning to ensure the correct HS400 timing setting.
Signed-off-by: Mengqi Zhang <mengqi.zhang@mediatek.com>
Link: https://lore.kernel.org/r/20231225093839.22931-2-mengqi.zhang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "Lin Gui (桂林)" <Lin.Gui@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f8def10f73a516b771051a2f70f2f0446902cb4f upstream.
Generic sdhci code registers LED device and uses host->runtime_suspended
flag to protect access to it. The sdhci-msm driver doesn't set this flag,
which causes a crash when LED is accessed while controller is runtime
suspended. Fix this by setting the flag correctly.
Cc: stable@vger.kernel.org
Fixes: 67e6db113c90 ("mmc: sdhci-msm: Add pm_runtime and system PM support")
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240321-sdhci-mmc-suspend-v1-1-fbc555a64400@8devices.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cf55a7acd1ed38afe43bba1c8a0935b51d1dc014 upstream.
Commit 4d0c8d0aef63 ("mmc: core: Use mrq.sbc in close-ended ffu") assigns
prev_idata = idatas[i - 1], but doesn't check that the iterator i is
greater than zero. Let's fix this by adding a check.
Fixes: 4d0c8d0aef63 ("mmc: core: Use mrq.sbc in close-ended ffu")
Link: https://lore.kernel.org/all/20231129092535.3278-1-avri.altman@wdc.com/
Cc: stable@vger.kernel.org
Signed-off-by: Mikko Rapeli <mikko.rapeli@linaro.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240313133744.2405325-2-mikko.rapeli@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0cdfe5b0bf295c0dee97436a8ed13336933a0211 upstream.
Commit 4d0c8d0aef63 ("mmc: core: Use mrq.sbc in close-ended ffu") adds
flags uint to struct mmc_blk_ioc_data, but it does not get initialized for
RPMB ioctls which now fails.
Let's fix this by always initializing the struct and flags to zero.
Fixes: 4d0c8d0aef63 ("mmc: core: Use mrq.sbc in close-ended ffu")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218587
Link: https://lore.kernel.org/all/20231129092535.3278-1-avri.altman@wdc.com/
Cc: stable@vger.kernel.org
Signed-off-by: Mikko Rapeli <mikko.rapeli@linaro.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240313133744.2405325-1-mikko.rapeli@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
HS200 mode
commit f9e2a5b00a35f2c064dc679808bc8db5cc779ed6 upstream.
"PM runtime functions" was been added in sdhci-omap driver in commit
f433e8aac6b9 ("mmc: sdhci-omap: Implement PM runtime functions") along
with "card power off and enable aggressive PM" in commit 3edf588e7fe0
("mmc: sdhci-omap: Allow SDIO card power off and enable aggressive PM").
Since then, the sdhci-omap driver doesn't work using mmc-hs200 mode
due to the tuning values being lost during a pm transition.
As for the sdhci_am654 driver, request a new tuning sequence before
suspend (sdhci_omap_runtime_suspend()), otherwise the device will
trigger cache flush error:
mmc1: cache flush error -110 (ETIMEDOUT)
mmc1: error -110 doing aggressive suspend
followed by I/O errors produced by fdisk -l /dev/mmcblk1boot1:
I/O error, dev mmcblk1boot0, sector 64384 op 0x0:(READ) flags 0x80700 phys_seg 1
prio class 2
I/O error, dev mmcblk1boot1, sector 64384 op 0x0:(READ) flags 0x80700 phys_seg 1
prio class 2
I/O error, dev mmcblk1boot1, sector 64384 op 0x0:(READ) flags 0x0 phys_seg 1
prio class 2
Buffer I/O error on dev mmcblk1boot1, logical block 8048, async page read
I/O error, dev mmcblk1boot0, sector 64384 op 0x0:(READ) flags 0x0 phys_seg 1
prio class 2
Buffer I/O error on dev mmcblk1boot0, logical block 8048, async page read
Don't re-tune if auto retuning is supported in HW (when SDHCI_TUNING_MODE_3
is available).
Link: https://lore.kernel.org/all/2e5f1997-564c-44e4-b357-6343e0dae7ab@smile.fr
Fixes: f433e8aac6b9 ("mmc: sdhci-omap: Implement PM runtime functions")
Signed-off-by: Romain Naour <romain.naour@skf.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240315234444.816978-1-romain.naour@smile.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4af59a8df5ea930038cd3355e822f5eedf4accc1 ]
Commit e7794c14fd73 ("mmc: rpmb: fixes pause retune on all RPMB
partitions.") added a mask check for 'part_type', but the mask used was
wrong leading to the code intended for rpmb also being executed for GP3.
On some MMCs (but not all) this would make gp3 partition inaccessible:
armadillo:~# head -c 1 < /dev/mmcblk2gp3
head: standard input: I/O error
armadillo:~# dmesg -c
[ 422.976583] mmc2: running CQE recovery
[ 423.058182] mmc2: running CQE recovery
[ 423.137607] mmc2: running CQE recovery
[ 423.137802] blk_update_request: I/O error, dev mmcblk2gp3, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
[ 423.237125] mmc2: running CQE recovery
[ 423.318206] mmc2: running CQE recovery
[ 423.397680] mmc2: running CQE recovery
[ 423.397837] blk_update_request: I/O error, dev mmcblk2gp3, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 423.408287] Buffer I/O error on dev mmcblk2gp3, logical block 0, async page read
the part_type values of interest here are defined as follow:
main 0
boot0 1
boot1 2
rpmb 3
gp0 4
gp1 5
gp2 6
gp3 7
so mask with EXT_CSD_PART_CONFIG_ACC_MASK (7) to correctly identify rpmb
Fixes: e7794c14fd73 ("mmc: rpmb: fixes pause retune on all RPMB partitions.")
Cc: stable@vger.kernel.org
Cc: Jorge Ramirez-Ortiz <jorge@foundries.io>
Signed-off-by: Dominique Martinet <dominique.martinet@atmark-techno.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240306-mmc-partswitch-v1-1-bf116985d950@codewreck.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e8d1b41e69d72c62865bebe8f441163ec00b3d44 ]
With the to-be-fixed commit, the reset_work handler cleared 'host->mrq'
outside of the spinlock protected critical section. That leaves a small
race window during execution of 'tmio_mmc_reset()' where the done_work
handler could grab a pointer to the now invalid 'host->mrq'. Both would
use it to call mmc_request_done() causing problems (see link below).
However, 'host->mrq' cannot simply be cleared earlier inside the
critical section. That would allow new mrqs to come in asynchronously
while the actual reset of the controller still needs to be done. So,
like 'tmio_mmc_set_ios()', an ERR_PTR is used to prevent new mrqs from
coming in but still avoiding concurrency between work handlers.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Closes: https://lore.kernel.org/all/20240220061356.3001761-1-dirk.behme@de.bosch.com/
Fixes: df3ef2d3c92c ("mmc: protect the tmio_mmc driver against a theoretical race")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Dirk Behme <dirk.behme@de.bosch.com>
Cc: stable@vger.kernel.org # 3.0+
Link: https://lore.kernel.org/r/20240305104423.3177-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
function
[ Upstream commit ae5004a40a262d329039b99b62bd3fe7645b66ad ]
This looks strange to call release_mem_region() in a remove function
without any request_mem_region() in the probe or "struct resource"
somewhere.
So remove the corresponding code.
Fixes: 3a96dff0f828 ("mmc: SD/MMC Host Controller for Wondermedia WM8505/WM8650")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/bb0bb1ed1e18de55e8c0547625bde271e64b8c31.1708983064.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 8e9f25a290ae0016353c9ea13314c95fb3207812 upstream.
Each time SD/mmc phy is initialized, at times, in some of
the attempts, phy fails to completes its initialization
which results into timeout error. Per the HW spec, it is
a pre-requisite to ensure a stable SD clock before a phy
initialization is attempted.
Fixes: 06c8b667ff5b ("mmc: sdhci-xenon: Add support to PHYs of Marvell Xenon SDHC")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Elad Nachman <enachman@marvell.com>
Link: https://lore.kernel.org/r/20240222200930.1277665-1-enachman@marvell.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 09e23823ae9a3e2d5d20f2e1efe0d6e48cef9129 upstream.
AC5X spec says PHY init complete bit must be polled until zero.
We see cases in which timeout can take longer than the standard
calculation on AC5X, which is expected following the spec comment above.
According to the spec, we must wait as long as it takes for that bit to
toggle on AC5X.
Cap that with 100 delay loops so we won't get stuck forever.
Fixes: 06c8b667ff5b ("mmc: sdhci-xenon: Add support to PHYs of Marvell Xenon SDHC")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Elad Nachman <enachman@marvell.com>
Link: https://lore.kernel.org/r/20240222191714.1216470-3-enachman@marvell.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ff3206d2186d84e4f77e1378ba1d225633f17b9b upstream.
Initializing an eMMC that's connected via a 1-bit bus is current failing,
if the HW (DT) informs that 4-bit bus is supported. In fact this is a
regression, as we were earlier capable of falling back to 1-bit mode, when
switching to 4/8-bit bus failed. Therefore, let's restore the behaviour.
Log for Samsung eMMC 5.1 chip connected via 1bit bus (only D0 pin)
Before patch:
[134509.044225] mmc0: switch to bus width 4 failed
[134509.044509] mmc0: new high speed MMC card at address 0001
[134509.054594] mmcblk0: mmc0:0001 BGUF4R 29.1 GiB
[134509.281602] mmc0: switch to bus width 4 failed
[134509.282638] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.282657] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.284598] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.284602] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.284609] ldm_validate_partition_table(): Disk read failed.
[134509.286495] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.286500] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.288303] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.288308] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.289540] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.289544] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.289553] mmcblk0: unable to read partition table
[134509.289728] mmcblk0boot0: mmc0:0001 BGUF4R 31.9 MiB
[134509.290283] mmcblk0boot1: mmc0:0001 BGUF4R 31.9 MiB
[134509.294577] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[134509.295835] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.295841] Buffer I/O error on dev mmcblk0, logical block 0, async page read
After patch:
[134551.089613] mmc0: switch to bus width 4 failed
[134551.090377] mmc0: new high speed MMC card at address 0001
[134551.102271] mmcblk0: mmc0:0001 BGUF4R 29.1 GiB
[134551.113365] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21
[134551.114262] mmcblk0boot0: mmc0:0001 BGUF4R 31.9 MiB
[134551.114925] mmcblk0boot1: mmc0:0001 BGUF4R 31.9 MiB
Fixes: 577fb13199b1 ("mmc: rework selection of bus speed mode")
Cc: stable@vger.kernel.org
Signed-off-by: Ivan Semenov <ivan@semenov.dev>
Link: https://lore.kernel.org/r/20240206172845.34316-1-ivan@semenov.dev
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6b1ba3f9040be5efc4396d86c9752cdc564730be upstream.
Turning on CONFIG_DMA_API_DEBUG_SG results in the following warning:
DMA-API: mmci-pl18x 48220000.mmc: cacheline tracking EEXIST,
overlapping mappings aren't supported
WARNING: CPU: 1 PID: 51 at kernel/dma/debug.c:568
add_dma_entry+0x234/0x2f4
Modules linked in:
CPU: 1 PID: 51 Comm: kworker/1:2 Not tainted 6.1.28 #1
Hardware name: STMicroelectronics STM32MP257F-EV1 Evaluation Board (DT)
Workqueue: events_freezable mmc_rescan
Call trace:
add_dma_entry+0x234/0x2f4
debug_dma_map_sg+0x198/0x350
__dma_map_sg_attrs+0xa0/0x110
dma_map_sg_attrs+0x10/0x2c
sdmmc_idma_prep_data+0x80/0xc0
mmci_prep_data+0x38/0x84
mmci_start_data+0x108/0x2dc
mmci_request+0xe4/0x190
__mmc_start_request+0x68/0x140
mmc_start_request+0x94/0xc0
mmc_wait_for_req+0x70/0x100
mmc_send_tuning+0x108/0x1ac
sdmmc_execute_tuning+0x14c/0x210
mmc_execute_tuning+0x48/0xec
mmc_sd_init_uhs_card.part.0+0x208/0x464
mmc_sd_init_card+0x318/0x89c
mmc_attach_sd+0xe4/0x180
mmc_rescan+0x244/0x320
DMA API debug brings to light leaking dma-mappings as dma_map_sg and
dma_unmap_sg are not correctly balanced.
If an error occurs in mmci_cmd_irq function, only mmci_dma_error
function is called and as this API is not managed on stm32 variant,
dma_unmap_sg is never called in this error path.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Fixes: 46b723dd867d ("mmc: mmci: add stm32 sdmmc variant")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240207143951.938144-1-christophe.kerello@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
by BIOS
commit 58aeb5623c2ebdadefe6352b14f8076a7073fea0 upstream.
Driver shall switch clock source from DLL clock to
OPE clock when power off card to ensure that card
can be identified with OPE clock by BIOS.
Signed-off-by: Fred Ai <fred.ai@bayhubtech.com>
Fixes:4be33cf18703 ("mmc: sdhci-pci-o2micro: Improve card input timing at SDR104/HS200 mode")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240203102908.4683-1-fredaibayhubtech@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cc9432c4fb159a3913e0ce3173b8218cd5bad2e0 upstream.
This change uses the appropriate _cansleep or non-sleeping API for
reading GPIO read-only state. This allows users with GPIOs that
never sleepbeing called in atomic context.
Implement the same mechanism as in commit 52af318c93e97 ("mmc: Allow
non-sleeping GPIO cd").
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240206083912.2543142-1-alexander.stein@ew.tq-group.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 84a6be7db9050dd2601c9870f65eab9a665d2d5d upstream.
There is no need to duplicate what SPI core or individual controller
drivers already do, i.e. mapping the buffers for DMA capable transfers.
Note, that the code, besides its redundancy, was buggy: strictly speaking
there is no guarantee, while it's true for those which can use this code
(see below), that the SPI host controller _is_ the device which does DMA.
Also see the Link tags below.
Additional notes. Currently only two SPI host controller drivers may use
premapped (by the user) DMA buffers:
- drivers/spi/spi-au1550.c
- drivers/spi/spi-fsl-spi.c
Both of them have DMA mapping support code. I don't expect that SPI host
controller code is worse than what has been done in mmc_spi. Hence I do
not expect any regressions here. Otherwise, I'm pretty much sure these
regressions have to be fixed in the respective drivers, and not here.
That said, remove all related pieces of DMA mapping code from mmc_spi.
Link: https://lore.kernel.org/linux-mmc/c73b9ba9-1699-2aff-e2fd-b4b4f292a3ca@raspberrypi.org/
Link: https://stackoverflow.com/questions/67620728/mmc-spi-issue-not-able-to-setup-mmc-sd-card-in-linux
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231207221901.3259962-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4d0c8d0aef6355660b6775d57ccd5d4ea2e15802 upstream.
Field Firmware Update (ffu) may use close-ended or open ended sequence.
Each such sequence is comprised of a write commands enclosed between 2
switch commands - to and from ffu mode. So for the close-ended case, it
will be: cmd6->cmd23-cmd25-cmd6.
Some host controllers however, get confused when multi-block rw is sent
without sbc, and may generate auto-cmd12 which breaks the ffu sequence.
I encountered this issue while testing fwupd (github.com/fwupd/fwupd)
on HP Chromebook x2, a qualcomm based QC-7c, code name - strongbad.
Instead of a quirk, or hooking the request function of the msm ops,
it would be better to fix the ioctl handling and make it use mrq.sbc
instead of issuing SET_BLOCK_COUNT separately.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231129092535.3278-1-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 09f164d393a6671e5ff8342ba6b3cb7fe3f20208 ]
The sdhci_omap is specific to older TI SoCs, update the
dependencies for those SoCs and compile testing. While we're
at it update the text to reflect the wider range of
supported TI SoCS the driver now supports.
Fixes: 7d326930d352 ("mmc: sdhci-omap: Add OMAP SDHCI driver")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20231220135950.433588-2-pbrobinson@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cb052da7f031b0d2309a4895ca236afb3b4bbf50 ]
The sdhci_am654 is specific to recent TI SoCs, update the
dependencies for those SoCs and compile testing. While we're
at it update the text to reflect the wider range of
supported TI SoCS the driver now supports.
Fixes: 41fd4caeb00b ("mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20231220135950.433588-1-pbrobinson@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 8abf77c88929b6d20fa4f9928b18d6448d64e293 upstream.
Some eMMC devices that do not close the auto clk gate after hw reset will
cause eMMC initialization to fail. Let's fix this.
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Fixes: ff874dbc4f86 ("mmc: sdhci-sprd: Disable CLK_AUTO when the clock is less than 400K")
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231204064934.21236-1-wenchao.chen@unisoc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1036f69e251380573e256568cf814506e3fb9988 upstream.
On RZ/Five SMARC EVK, where probing of SDHI is deferred due to probe
deferral of the vqmmc-supply regulator:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/time/timer.c:1738 __run_timers.part.0+0x1d0/0x1e8
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 6.7.0-rc4 #101
Hardware name: Renesas SMARC EVK based on r9a07g043f01 (DT)
epc : __run_timers.part.0+0x1d0/0x1e8
ra : __run_timers.part.0+0x134/0x1e8
epc : ffffffff800771a4 ra : ffffffff80077108 sp : ffffffc800003e60
gp : ffffffff814f5028 tp : ffffffff8140c5c0 t0 : ffffffc800000000
t1 : 0000000000000001 t2 : ffffffff81201300 s0 : ffffffc800003f20
s1 : ffffffd8023bc4a0 a0 : 00000000fffee6b0 a1 : 0004010000400000
a2 : ffffffffc0000016 a3 : ffffffff81488640 a4 : ffffffc800003e60
a5 : 0000000000000000 a6 : 0000000004000000 a7 : ffffffc800003e68
s2 : 0000000000000122 s3 : 0000000000200000 s4 : 0000000000000000
s5 : ffffffffffffffff s6 : ffffffff81488678 s7 : ffffffff814886c0
s8 : ffffffff814f49c0 s9 : ffffffff81488640 s10: 0000000000000000
s11: ffffffc800003e60 t3 : 0000000000000240 t4 : 0000000000000a52
t5 : ffffffd8024ae018 t6 : ffffffd8024ae038
status: 0000000200000100 badaddr: 0000000000000000 cause: 0000000000000003
[<ffffffff800771a4>] __run_timers.part.0+0x1d0/0x1e8
[<ffffffff800771e0>] run_timer_softirq+0x24/0x4a
[<ffffffff80809092>] __do_softirq+0xc6/0x1fa
[<ffffffff80028e4c>] irq_exit_rcu+0x66/0x84
[<ffffffff80800f7a>] handle_riscv_irq+0x40/0x4e
[<ffffffff80808f48>] call_on_irq_stack+0x1c/0x28
---[ end trace 0000000000000000 ]---
What happens?
renesas_sdhi_probe()
{
tmio_mmc_host_alloc()
mmc_alloc_host()
INIT_DELAYED_WORK(&host->detect, mmc_rescan);
devm_request_irq(tmio_mmc_irq);
/*
* After this, the interrupt handler may be invoked at any time
*
* tmio_mmc_irq()
* {
* __tmio_mmc_card_detect_irq()
* mmc_detect_change()
* _mmc_detect_change()
* mmc_schedule_delayed_work(&host->detect, delay);
* }
*/
tmio_mmc_host_probe()
tmio_mmc_init_ocr()
-EPROBE_DEFER
tmio_mmc_host_free()
mmc_free_host()
}
When expire_timers() runs later, it warns because the MMC host structure
containing the delayed work was freed, and now contains an invalid work
function pointer.
Fix this by cancelling any pending delayed work before releasing the
MMC host structure.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/205dc4c91b47e31b64392fe2498c7a449e717b4b.1701689330.git.geert+renesas@glider.be
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e7794c14fd73e5eb4a3e0ecaa5334d5a17377c50 upstream.
When RPMB was converted to a character device, it added support for
multiple RPMB partitions (Commit 97548575bef3 ("mmc: block: Convert RPMB to
a character device").
One of the changes in this commit was transforming the variable target_part
defined in __mmc_blk_ioctl_cmd into a bitmask. This inadvertently regressed
the validation check done in mmc_blk_part_switch_pre() and
mmc_blk_part_switch_post(), so let's fix it.
Fixes: 97548575bef3 ("mmc: block: Convert RPMB to a character device")
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231201153143.1449753-1-jorge@foundries.io
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8c124d998ea0c9022e247b11ac51f86ec8afa0e1 upstream.
Commit 4bc31edebde5 ("mmc: core: Set HS clock speed before sending
HS CMD13") set HS clock (52MHz) before switching to HS mode. For this
freq, FCLK_DIV5 will be selected and div value is 10 (reg value is 9).
Then we set rx_clk_phase to 11 or 15 which is out of range and make
hardware frozen. After we send command request, no irq will be
interrupted and the mmc driver will keep to wait for request finished,
even durning rebooting.
So let's set it to Phase 90 which should work in most cases. Then let
meson_mx_sdhc_execute_tuning() to find the accurate value for data
transfer.
If this doesn't work, maybe need to define a factor in dts.
Fixes: e4bf1b0970ef ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host")
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/TYZPR01MB5556A3E71554A2EC08597EA4C9CDA@TYZPR01MB5556.apcprd01.prod.exchangelabs.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 477865af60b2117ceaa1d558e03559108c15c78c ]
With cat regulator_summary, we found that vqmmc was not shutting
down after the card was pulled.
cat /sys/kernel/debug/regulator/regulator_summary
1.before fix
1)Insert SD card
vddsdio 1 1 0 unknown 3500mV 0mA 1200mV 3750mV
71100000.mmc-vqmmc 1 0mA 3500mV 3600mV
2)Pull out the SD card
vddsdio 1 1 0 unknown 3500mV 0mA 1200mV 3750mV
71100000.mmc-vqmmc 1 0mA 3500mV 3600mV
2.after fix
1)Insert SD cardt
vddsdio 1 1 0 unknown 3500mV 0mA 1200mV 3750mV
71100000.mmc-vqmmc 1 0mA 3500mV 3600mV
2)Pull out the SD card
vddsdio 0 1 0 unknown 3500mV 0mA 1200mV 3750mV
71100000.mmc-vqmmc 0 0mA 3500mV 3600mV
Fixes: fb8bd90f83c4 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231115083406.7368-1-wenchao.chen@unisoc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8d91f3f8ae57e6292142ca89f322e90fa0d6ac02 ]
There's a number of drivers (e.g. dw_mmc, meson-gx, mmci, sunxi) using
the same mechanism and a private flag vqmmc_enabled to deal with
enabling/disabling the vqmmc regulator.
Move this to the core and create new helpers mmc_regulator_enable_vqmmc
and mmc_regulator_disable_vqmmc.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/71586432-360f-9b92-17f6-b05a8a971bc2@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Stable-dep-of: 477865af60b2 ("mmc: sdhci-sprd: Fix vqmmc not shutting down after the card was pulled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c616696a902987352426fdaeec1b0b3240949e6b upstream.
STOP command does not guarantee to wait while busy, but subsequent command
MMC_CMDQ_TASK_MGMT to discard the queue will fail if the card is busy, so
be sure to wait by employing mmc_poll_for_busy().
Fixes: 72a5af554df8 ("mmc: core: Add support for handling CQE requests")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Christian Loehle <christian.loehle@arm.com>
Link: https://lore.kernel.org/r/20231103084720.6886-4-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 174925d340aac55296318e43fd96c0e1d196e105 upstream.
During CQE error recovery, error-free data commands get requeued if there
is any data left to transfer, but non-data commands are completed even
though they have not been processed. Requeue them instead.
Note the only non-data command is cache flush, which would have resulted in
a cache flush being lost if it was queued at the time of CQE recovery.
Fixes: 1e8e55b67030 ("mmc: block: Add CQE support")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103084720.6886-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8155d1fa3a747baad5caff5f8303321d68ddd48c upstream.
It is important that MMC_CMDQ_TASK_MGMT command to discard the queue is
successful because otherwise a subsequent reset might fail to flush the
cache first. Retry it and the previous STOP command.
Fixes: 72a5af554df8 ("mmc: core: Add support for handling CQE requests")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103084720.6886-5-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1de1b77982e1a1df9707cb11f9b1789e6b8919d4 upstream.
If a task completion notification (TCN) is received when there is no
outstanding task, the cqhci driver issues a "spurious TCN" warning. This
was observed to happen right after CQE error recovery.
When an error interrupt is received the driver runs recovery logic.
It halts the controller, clears all pending tasks, and then re-enables
it. On some platforms, like Intel Jasper Lake, a stale task completion
event was observed, regardless of the CQHCI_CLEAR_ALL_TASKS bit being set.
This results in either:
a) Spurious TC completion event for an empty slot.
b) Corrupted data being passed up the stack, as a result of premature
completion for a newly added task.
Rather than add a quirk for affected controllers, ensure tasks are cleared
by toggling CQHCI_ENABLE, which would happen anyway if
cqhci_clear_all_tasks() timed out. This is simpler and should be safe and
effective for all controllers.
Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host")
Cc: stable@vger.kernel.org
Reported-by: Kornel Dulęba <korneld@chromium.org>
Tested-by: Kornel Dulęba <korneld@chromium.org>
Co-developed-by: Kornel Dulęba <korneld@chromium.org>
Signed-off-by: Kornel Dulęba <korneld@chromium.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103084720.6886-7-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 35597bdb04ec27ef3b1cea007dc69f8ff5df75a5 upstream.
A correctly operating controller should successfully halt and clear tasks.
Failure may result in errors elsewhere, so promote messages from debug to
warnings.
Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103084720.6886-6-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b578d5d18e929aa7c007a98cce32657145dde219 upstream.
Failing to halt complicates the recovery. Additionally, unless the card or
controller are stuck, which is expected to be very rare, then the halt
should succeed, so it is better to wait. Set a large timeout.
Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103084720.6886-3-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d9ed644f58670865cf067351deb71010bd87a52f upstream.
To address IO performance commit f9e5b33934ce
("mmc: host: Improve I/O read/write performance for GL9763E")
limited LPM negotiation to runtime suspend state.
The problem is that it only flips the switch in the runtime PM
resume/suspend logic.
Disable LPM negotiation in gl9763e_add_host.
This helps in two ways:
1. It was found that the LPM switch stays in the same position after
warm reboot. Having it set in init helps with consistency.
2. Disabling LPM during the first runtime resume leaves us susceptible
to the performance issue in the time window between boot and the
first runtime suspend.
Fixes: f9e5b33934ce ("mmc: host: Improve I/O read/write performance for GL9763E")
Cc: stable@vger.kernel.org
Signed-off-by: Kornel Dulęba <korneld@chromium.org>
Reviewed-by: Sven van Ashbrook <svenva@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20231114115516.1585361-1-korneld@chromium.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 85dd3af64965c1c0eb7373b340a1b1f7773586b0 upstream.
Due to a flaw in the hardware design, the GL9755 replay timer frequently
times out when ASPM is enabled. As a result, the warning messages will
often appear in the system log when the system accesses the GL9755
PCI config. Therefore, the replay timer timeout must be masked.
Fixes: 36ed2fd32b2c ("mmc: sdhci-pci-gli: A workaround to allow GL9755 to enter ASPM L1.2")
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Kai-Heng Feng <kai.heng.geng@canonical.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231107095741.8832-3-victorshihgli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 015c9cbcf0ad709079117d27c2094a46e0eadcdb upstream.
Due to a flaw in the hardware design, the GL9750 replay timer frequently
times out when ASPM is enabled. As a result, the warning messages will
often appear in the system log when the system accesses the GL9750
PCI config. Therefore, the replay timer timeout must be masked.
Fixes: d7133797e9e1 ("mmc: sdhci-pci-gli: A workaround to allow GL9750 to enter ASPM L1.2")
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Kai-Heng Feng <kai.heng.geng@canonical.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231107095741.8832-2-victorshihgli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d7133797e9e1b72fd89237f68cb36d745599ed86 upstream.
When GL9750 enters ASPM L1 sub-states, it will stay at L1.1 and will not
enter L1.2. The workaround is to toggle PM state to allow GL9750 to enter
ASPM L1.2.
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20230912091710.7797-1-victorshihgli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ed9009ad300c0f15a3ecfe9613547b1962bde02c upstream.
Micron MTFC4GACAJCN eMMC supports cache but requires that flush cache
operation be allowed only after a write has occurred. Otherwise, the
cache flush command or subsequent commands will time out.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Rafael Beims <rafael.beims@toradex.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231030224809.59245-1-beanhuo@iokpp.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 71956d0cb56c1e5f9feeb4819db87a076418e930 upstream.
ti,otap-del-sel-legacy/ti,itap-del-sel-legacy passed from DT
are currently ignored for all SD/MMC and eMMC modes. Fix this
by making start loop index to MMC_TIMING_LEGACY.
Fixes: 8ee5fc0e0b3b ("mmc: sdhci_am654: Update OTAPDLY writes")
Signed-off-by: Nitin Yadav <n-yadav@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231026061458.1116276-1-n-yadav@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
