| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- unify AER decoding for native and ACPI CPER sources (Alexandru
Gagniuc)
- add TLP header info to AER tracepoint (Thomas Tai)
- add generic pcie_wait_for_link() interface (Oza Pawandeep)
- handle AER ERR_FATAL by removing and re-enumerating devices, as
Downstream Port Containment does (Oza Pawandeep)
- factor out common code between AER and DPC recovery (Oza Pawandeep)
- stop triggering DPC for ERR_NONFATAL errors (Oza Pawandeep)
- share ERR_FATAL recovery path between AER and DPC (Oza Pawandeep)
- disable ASPM L1.2 substate if we don't have LTR (Bjorn Helgaas)
- respect platform ownership of LTR (Bjorn Helgaas)
- clear interrupt status in top half to avoid interrupt storm (Oza
Pawandeep)
- neaten pci=earlydump output (Andy Shevchenko)
- avoid errors when extended config space inaccessible (Gilles Buloz)
- prevent sysfs disable of device while driver attached (Christoph
Hellwig)
- use core interface to report PCIe link properties in bnx2x, bnxt_en,
cxgb4, ixgbe (Bjorn Helgaas)
- remove unused pcie_get_minimum_link() (Bjorn Helgaas)
- fix use-before-set error in ibmphp (Dan Carpenter)
- fix pciehp timeouts caused by Command Completed errata (Bjorn
Helgaas)
- fix refcounting in pnv_php hotplug (Julia Lawall)
- clear pciehp Presence Detect and Data Link Layer Status Changed on
resume so we don't miss hotplug events (Mika Westerberg)
- only request pciehp control if we support it, so platform can use
ACPI hotplug otherwise (Mika Westerberg)
- convert SHPC to be builtin only (Mika Westerberg)
- request SHPC control via _OSC if we support it (Mika Westerberg)
- simplify SHPC handoff from firmware (Mika Westerberg)
- fix an SHPC quirk that mistakenly included *all* AMD bridges as well
as devices from any vendor with device ID 0x7458 (Bjorn Helgaas)
- assign a bus number even to non-native hotplug bridges to leave
space for acpiphp additions, to fix a common Thunderbolt xHCI
hot-add failure (Mika Westerberg)
- keep acpiphp from scanning native hotplug bridges, to fix common
Thunderbolt hot-add failures (Mika Westerberg)
- improve "partially hidden behind bridge" messages from core (Mika
Westerberg)
- add macros for PCIe Link Control 2 register (Frederick Lawler)
- replace IB/hfi1 custom macros with PCI core versions (Frederick
Lawler)
- remove dead microblaze and xtensa code (Bjorn Helgaas)
- use dev_printk() when possible in xtensa and mips (Bjorn Helgaas)
- remove unused pcie_port_acpi_setup() and portdrv_acpi.c (Bjorn
Helgaas)
- add managed interface to get PCI host bridge resources from OF (Jan
Kiszka)
- add support for unbinding generic PCI host controller (Jan Kiszka)
- fix memory leaks when unbinding generic PCI host controller (Jan
Kiszka)
- request legacy VGA framebuffer only for VGA devices to avoid false
device conflicts (Bjorn Helgaas)
- turn on PCI_COMMAND_IO & PCI_COMMAND_MEMORY in pci_enable_device()
like everybody else, not in pcibios_fixup_bus() (Bjorn Helgaas)
- add generic enable function for simple SR-IOV hardware (Alexander
Duyck)
- use generic SR-IOV enable for ena, nvme (Alexander Duyck)
- add ACS quirk for Intel 7th & 8th Gen mobile (Alex Williamson)
- add ACS quirk for Intel 300 series (Mika Westerberg)
- enable register clock for Armada 7K/8K (Gregory CLEMENT)
- reduce Keystone "link already up" log level (Fabio Estevam)
- move private DT functions to drivers/pci/ (Rob Herring)
- factor out dwc CONFIG_PCI Kconfig dependencies (Rob Herring)
- add DesignWare support to the endpoint test driver (Gustavo
Pimentel)
- add DesignWare support for endpoint mode (Gustavo Pimentel)
- use devm_ioremap_resource() instead of devm_ioremap() in dra7xx and
artpec6 (Gustavo Pimentel)
- fix Qualcomm bitwise NOT issue (Dan Carpenter)
- add Qualcomm runtime PM support (Srinivas Kandagatla)
- fix DesignWare enumeration below bridges (Koen Vandeputte)
- use usleep() instead of mdelay() in endpoint test (Jia-Ju Bai)
- add configfs entries for pci_epf_driver device IDs (Kishon Vijay
Abraham I)
- clean up pci_endpoint_test driver (Gustavo Pimentel)
- update Layerscape maintainer email addresses (Minghuan Lian)
- add COMPILE_TEST to improve build test coverage (Rob Herring)
- fix Hyper-V bus registration failure caused by domain/serial number
confusion (Sridhar Pitchai)
- improve Hyper-V refcounting and coding style (Stephen Hemminger)
- avoid potential Hyper-V hang waiting for a response that will never
come (Dexuan Cui)
- implement Mediatek chained IRQ handling (Honghui Zhang)
- fix vendor ID & class type for Mediatek MT7622 (Honghui Zhang)
- add Mobiveil PCIe host controller driver (Subrahmanya Lingappa)
- add Mobiveil MSI support (Subrahmanya Lingappa)
- clean up clocks, MSI, IRQ mappings in R-Car probe failure paths
(Marek Vasut)
- poll more frequently (5us vs 5ms) while waiting for R-Car data link
active (Marek Vasut)
- use generic OF parsing interface in R-Car (Vladimir Zapolskiy)
- add R-Car V3H (R8A77980) "compatible" string (Sergei Shtylyov)
- add R-Car gen3 PHY support (Sergei Shtylyov)
- improve R-Car PHYRDY polling (Sergei Shtylyov)
- clean up R-Car macros (Marek Vasut)
- use runtime PM for R-Car controller clock (Dien Pham)
- update arm64 defconfig for Rockchip (Shawn Lin)
- refactor Rockchip code to facilitate both root port and endpoint
mode (Shawn Lin)
- add Rockchip endpoint mode driver (Shawn Lin)
- support VMD "membar shadow" feature (Jon Derrick)
- support VMD bus number offsets (Jon Derrick)
- add VMD "no AER source ID" quirk for more device IDs (Jon Derrick)
- remove unnecessary host controller CONFIG_PCIEPORTBUS Kconfig
selections (Bjorn Helgaas)
- clean up quirks.c organization and whitespace (Bjorn Helgaas)
* tag 'pci-v4.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (144 commits)
PCI/AER: Replace struct pcie_device with pci_dev
PCI/AER: Remove unused parameters
PCI: qcom: Include gpio/consumer.h
PCI: Improve "partially hidden behind bridge" log message
PCI: Improve pci_scan_bridge() and pci_scan_bridge_extend() doc
PCI: Move resource distribution for single bridge outside loop
PCI: Account for all bridges on bus when distributing bus numbers
ACPI / hotplug / PCI: Drop unnecessary parentheses
ACPI / hotplug / PCI: Mark stale PCI devices disconnected
ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug
PCI: hotplug: Add hotplug_is_native()
PCI: shpchp: Add shpchp_is_native()
PCI: shpchp: Fix AMD POGO identification
PCI: mobiveil: Add MSI support
PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver
PCI/AER: Decode Error Source Requester ID
PCI/AER: Remove aer_recover_work_func() forward declaration
PCI/DPC: Use the generic pcie_do_fatal_recovery() path
PCI/AER: Pass service type to pcie_do_fatal_recovery()
PCI/DPC: Disable ERR_NONFATAL handling by DPC
...
|
|
Nearby code that also tests port suggests that the P0 constant should be
used when port is zero.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1;
@@
* e ? e1 : e1
// </smpl>
Fixes: 6c3218c6f7e5 ("bnx2x: Adjust ETS to 578xx")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the checkpatch issue of NULL comparison. Replace x == NULL
with !x, by using the following coccinelle script:
@disable is_null@
expression e;
@@
-e==NULL
+!e
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following coccinelle script removes extra parentheses to fix the
clang warning of extraneous parentheses.
@disable paren@
identifier i;
expression e;
statement s;
@@
if (
-(i == e)
+i == e
)
s
Suggested-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tx-timeout mostly happens due to some issue in the device. In such cases,
debug dump would be helpful for identifying the cause of the issue.
This patch adds support to spill debug data during the Tx timeout. Here
bnx2x_panic_dump() API is used instead of bnx2x_panic(), since we still
want to allow the Tx-timeout recovery a chance to succeed.
Changes from previous version:
-------------------------------
v2: Fixed a coding error.
Please consider applying this to "net-next".
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously the driver used pcie_get_minimum_link() to warn when the NIC
is in a slot that can't supply as much bandwidth as the NIC could use.
pcie_get_minimum_link() can be misleading because it finds the slowest link
and the narrowest link (which may be different links) without considering
the total bandwidth of each link. For a path with a 16 GT/s x1 link and a
2.5 GT/s x16 link, it returns 2.5 GT/s x1, which corresponds to 250 MB/s of
bandwidth, not the true available bandwidth of about 1969 MB/s for a
16 GT/s x1 link.
Use pcie_print_link_status() to report PCIe link speed and possible
limitations instead of implementing this in the driver itself. This finds
the slowest link in the path to the device by computing the total bandwidth
of each link and compares that with the capabilities of the device.
The dmesg change is:
- PCIe: Speed %s Width x%d
+ %u.%03u Gb/s available PCIe bandwidth (%s x%d link)
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Previously the driver used pcie_get_minimum_link() to warn when the NIC
is in a slot that can't supply as much bandwidth as the NIC could use.
pcie_get_minimum_link() can be misleading because it finds the slowest link
and the narrowest link (which may be different links) without considering
the total bandwidth of each link. For a path with a 16 GT/s x1 link and a
2.5 GT/s x16 link, it returns 2.5 GT/s x1, which corresponds to 250 MB/s of
bandwidth, not the true available bandwidth of about 1969 MB/s for a
16 GT/s x1 link.
Use pcie_print_link_status() to report PCIe link speed and possible
limitations instead of implementing this in the driver itself. This finds
the slowest link in the path to the device by computing the total bandwidth
of each link and compares that with the capabilities of the device.
The dmesg change is:
- %s (%c%d) PCI-E x%d %s found at mem %lx, IRQ %d, node addr %pM
+ %s (%c%d) PCI-E found at mem %lx, IRQ %d, node addr %pM
+ %u.%03u Gb/s available PCIe bandwidth (%s x%d link)
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code already forwards the VF MAC address to the PF, except
in one case. If the VF driver gets a valid MAC address from the firmware
during probe time, it will not forward the MAC address to the PF,
incorrectly assuming that the PF already knows the MAC address. This
causes "ip link show" to show zero VF MAC addresses for this case.
This assumption is not correct. Newer firmware remembers the VF MAC
address last used by the VF and provides it to the VF driver during
probe. So we need to always forward the VF MAC address to the PF.
The forwarded MAC address may now be the PF assigned MAC address and so we
need to make sure we approve it for this case.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For SFP+ modules, 0xA2 page is available only when Diagnostic Monitoring
Type [Address A0h, Byte 92] is implemented. Extend bnxt_get_module_info(),
to read optical diagnostics support at offset 92(0x5c) and set eeprom_len
length to ETH_MODULE_SFF_8436_LEN (to exclude A2 page), if dianostics is
not supported.
Also in bnxt_get_module_info(), module id is read from offset 0x5e which
is not correct. It was working by accident, as offset was not effective
without setting enables flag in the firmware request. SFP module id is
present at location 0. Fix this by removing the offset and read it
from location 0.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only non-NPAR PFs need to actively check and manage unsupported link
speeds. NPAR functions and VFs do not control the link speed and
should skip the unsupported speed detection logic, to avoid warning
messages from firmware rejecting the unsupported firmware calls.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A recent change to reduce delay granularity waiting for firmware
reponse has caused a regression. With a tighter delay loop,
the driver may see the beginning part of the response faster.
The original 5 usec delay to wait for the rest of the message
is not long enough and some messages are detected as invalid.
Increase the maximum wait time from 5 usec to 20 usec. Also, fix
the debug message that shows the total delay time for the response
when the message times out. With the new logic, the delay time
is not fixed per iteration of the loop, so we define a macro to
show the total delay time.
Fixes: 9751e8e71487 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tg3_free_consistent() calls dma_free_coherent() to free tp->hw_stats
under spinlock and can trigger BUG_ON() in vunmap() because vunmap()
may sleep. Fix it by removing the spinlock and relying on the
TG3_FLAG_INIT_COMPLETE flag to prevent race conditions between
tg3_get_stats64() and tg3_free_consistent(). TG3_FLAG_INIT_COMPLETE
is always cleared under tp->lock before tg3_free_consistent()
and therefore tg3_get_stats64() can safely access tp->hw_stats
under tp->lock if TG3_FLAG_INIT_COMPLETE is set.
Fixes: f5992b72ebe0 ("tg3: Fix race condition in tg3_get_stats64().")
Reported-by: Zumeng Chen <zumeng.chen@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Overlapping changes in selftests Makefile.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to spelling mistake in netdev_warn warning message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add logic to reserve default rings at driver open time if none was
reserved during probe time. This will happen when the PF driver did
not provision minimum rings to the VF, due to more limited resources.
Driver open will only succeed if some minimum rings can be reserved.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For completeness and correctness, the VF driver needs to reserve these
RSS and L2 contexts.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When rings are more limited and the PF has not provisioned minimum
guaranteed rings to the VF, do not reserve rings during driver probe.
Wait till device open before reserving rings when they will be used.
Device open will succeed if some minimum rings can be successfully
reserved and allocated.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code does not reserve rings during ethtool -L when the device
is down. The rings will be reserved when the device is later opened.
Change it to reserve rings during ethtool -L when the device is down.
This provides a better guarantee that the device open will be successful
when the rings are reserved ahead of time.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds debugfs support for bnxt_en with the purpose of allowing users
to examine the current DIM profile in use for each receive queue. This
was instrumental in debugging issues found with DIM and ensuring that
the profiles we expect to use are the profiles being used.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Testing with DIM enabled on older kernels indicated that firmware calls
were slower than expected. More detailed analysis indicated that the
default 25us delay was higher than necessary. Reducing the time spend in
usleep_range() for the first several calls would reduce the overall
latency of firmware calls on newer Intel processors.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This keeps the RING_IDLE flag set in hardware for higher coalesce
settings by default and improved latency.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware does not allow the operation and would return failure, causing
a warning in dmesg. So check for VF and disallow it in the driver.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add counters to display sum of rx/tx_discard_pkts of all rings as
function level statistics via ethtool.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace switch statements printing different messages for every ring type
with a common message.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Older firmware will reject this call and cause an error message to
be printed by the VF driver.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware messages that are forwarded from PF to VFs are encapsulated.
The size of these encapsulated messages must not exceed the maximum
defined message size. Add appropriate checks to avoid oversize
messages. Firmware messages may be expanded in future specs and
this will provide some guardrails to avoid data corruption.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initially, the MQPRIO TCs are mapped 1:1 directly to the hardware
queues. Some of these hardware queues are configured to be lossless.
When PFC is enabled on one of more TCs, we now need to remap the
TCs that have PFC enabled to the lossless hardware queues.
After remapping, we need to close and open the NIC for the new
mapping to take effect. We also need to reprogram all ETS parameters.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current driver maps MQPRIO traffic classes directly 1:1 to the
internal hardware queues (TC0 maps to hardware queue 0, etc). This
direct mapping requires the internal hardware queues to be reconfigured
from lossless to lossy and vice versa when necessary. This
involves reconfiguring internal buffer thresholds which is
disruptive and not always reliable.
Implement a new scheme to map TCs to internal hardware queues by
matching up their PFC requirements. This will eliminate the need
to reconfigure a hardware queue internal buffers at run time. After
remapping, the NIC is closed and opened for the new TC to hardware
queues to take effect.
This patch only adds the basic mapping logic.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While adding the DSA notifier, we will be sending DSA notifications with
info->master that is going to point to a particular net_device instance.
Our logic in bcm_sysport_map_queues() correctly disambiguates net_device
instances that are not covered by our own driver, but it will not make
sure that info->master points to a particular driver instance that we
are interested in. In a system where e.g: two or more SYSTEMPORT
instances are registered, this would lead in programming two or more
times the queue mapping, completely messing with the logic which does
the queue/port allocation and tracking.
Fix this by looking at the notifier_block pointer which is unique per
instance and allows us to go back to our driver private structure, and
in turn to the backing net_device instance.
Fixes: d156576362c0 ("net: systemport: Establish lower/upper queue mapping")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Preparation for introducing adaptive TX to net DIM.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts were simple overlapping changes in microchip
driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some firmware images, the length of BNX_DIR_TYPE_PKG_LOG nvram type
could be greater than the fixed buffer length of 4096 bytes allocated by
the driver. This was causing HWRM_NVM_READ to copy more data to the buffer
than the allocated size, causing general protection fault.
Fix the issue by allocating the exact buffer length returned by
HWRM_NVM_FIND_DIR_ENTRY, instead of 4096. Move the kzalloc() call
into the bnxt_get_pkgver() function.
Fixes: 3ebf6f0a09a2 ("bnxt_en: Add installed-package firmware version reporting via Ethtool GDRVINFO")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
w/ bpf_xdp_adjust_tail helper xdp's data_end pointer could be changed as
well (only "decrease" of pointer's location is going to be supported).
changing of this pointer will change packet's size.
for bnxt driver we will just calculate packet's length unconditionally
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Nikita V. Shirokov <tehnerd@tehnerd.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
When open fails during ethtool -L ring change, for example, the driver
may crash at bnxt_free_irq() because bp->bnapi is NULL.
If we fail to allocate all the new rings, bnxt_open_nic() will free
all the memory including bp->bnapi. Subsequent call to bnxt_close_nic()
will try to dereference bp->bnapi in bnxt_free_irq().
Fix it by checking for !bp->bnapi in bnxt_free_irq().
Fixes: e5811b8c09df ("bnxt_en: Add IRQ remapping logic.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With recent changes to reserve both L2 and RDMA rings, we need to include
the RDMA rings in bnxt_check_rings(). Otherwise we will under-estimate
the rings we need during ethtool -L and may lead to failure.
Fixes: fbcfc8e46741 ("bnxt_en: Reserve completion rings and MSIX for bnxt_re RDMA driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While a VF is configured with a bigger mtu (> 1500), any packets that
are punted to the VF-rep (slow-path) get dropped by OVS kernel-datapath
with the following message: "dropped over-mtu packet". Fix this by
returning the max-mtu value for a VF-rep derived from its corresponding VF.
VF-rep's mtu can be changed using 'ip' command as shown in this example:
$ ip link set bnxt0_pf0vf0 mtu 9000
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver currently uses src port field (along with other fields) in the
decap tunnel key, while looking up and adding tunnel nodes. This leads to
redundant cfa_decap_filter_alloc() requests to the FW and flow-miss in the
flow engine. Fix this by ignoring the src port field in decap tunnel nodes.
Fixes: f484f6782e01 ("bnxt_en: add hwrm FW cmds for cfa_encap_record and decap_filter")
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before this patch the following commands would succeed as far as the
user was concerned:
$ tc qdisc add dev p1p1 ingress
$ tc filter add dev p1p1 parent ffff: protocol all \
flower skip_sw action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw src_mac 00:02:00:00:00:01/44 action drop
The current flow offload infrastructure used does not support wildcard
matching for ethernet headers, so do not allow the second or third
commands to succeed. If a user wants to drop traffic on that interface
the protocol and MAC addresses need to be specified explicitly:
$ tc qdisc add dev p1p1 ingress
$ tc filter add dev p1p1 parent ffff: protocol arp \
flower skip_sw action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw action drop
...
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw src_mac 00:02:00:00:00:01 action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw src_mac 00:02:00:00:00:02 action drop
...
There are also checks for VLAN parameters in this patch as other callers
may wildcard those parameters even if tc does not. Using different
flow infrastructure could allow this to work in the future for L2 flows,
but for now it does not.
Fixes: 2ae7408fedfe ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix ethtool .get_rxfh() crash by checking for valid indirection table
address before copying the data.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb->protocol is a __be16 which we would be calling htons() against,
while this is not wrong per-se as it correctly results in swapping the
value on LE hosts, this still upsets sparse. Adopt a similar pattern to
what other drivers do and just assign ip_ver to skb->protocol, and then
use htons() against the different constants such that the compiler can
resolve the values at build time.
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb->protocol is a __be16 which we would be calling htons() against,
while this is not wrong per-se as it correctly results in swapping the
value on LE hosts, this still upsets sparse. Adopt a similar pattern to
what other drivers do and just assign ip_ver to skb->protocol, and then
use htons() against the different constants such that the compiler can
resolve the values at build time.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bgmac_dma_tx_ring_free() assigns the ctl1 word which is a litle endian
32-bit word without using proper accessors, fix this, and because a
length cannot be negative, use unsigned int while at it.
Fixes: 9cde94506eac ("bgmac: implement scatter/gather support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All the members: base, idm_base and nicpm_base should be annotated with
__iomem since they are pointers to register space. This fixes a bunch of
sparse reported warnings.
Fixes: f6a95a24957a ("net: ethernet: bgmac: Add platform device support")
Fixes: dd5c5d037f5e ("net: ethernet: bgmac: add NS2 support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the driver needs to re-initailize the IRQ vectors, we make the
new ulp_irq_stop() call to tell the RDMA driver to disable and free
the IRQ vectors. After IRQ vectors have been re-initailized, we
make the ulp_irq_restart() call to tell the RDMA driver that
IRQs can be restarted.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add additional logic to reserve completion rings for the bnxt_re driver
when it requests MSIX vectors. The function bnxt_cp_rings_in_use()
will return the total number of completion rings used by both drivers
that need to be reserved. If the network interface in up, we will
close and open the NIC to reserve the new set of completion rings and
re-initialize the vectors.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor bnxt_need_reserve_rings() slightly so that __bnxt_reserve_rings()
can call it and remove some duplicated code.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add remapping logic so that bnxt_en can use any arbitrary MSIX vectors.
This will allow the driver to reserve one range of MSIX vectors to be
used by both bnxt_en and bnxt_re. bnxt_en can now skip over the MSIX
vectors used by bnxt_re.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the current code, the range of MSIX vectors allocated for the RDMA
driver is disjoint from the network driver. This creates a problem
for the new firmware ring reservation scheme. The new scheme requires
the reserved completion rings/MSIX vectors to be in a contiguous
range.
Change the logic to allocate RDMA MSIX vectors to be contiguous with
the vectors used by bnxt_en on new firmware using the new scheme.
The new function bnxt_get_num_msix() calculates the exact number of
vectors needed by both drivers.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the driver code makes some assumptions about the group index
and the map index of rings. This makes the code more difficult to
understand and less flexible.
Improve it by adding the grp_idx and map_idx fields explicitly to the
bnxt_ring_struct as a union. The grp_idx is initialized for each tx ring
and rx agg ring during init. time. We do the same for the map_idx for
each cmpl ring.
The grp_idx ties the tx ring to the ring group. The map_idx is the
doorbell index of the ring. With this new infrastructure, we can change
the ring index mapping scheme easily in the future.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
