| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The original behavior introduced by commit c6acd629eec7 ("net/mlx5e: Add
support for devlink-port in non-representors mode") correctly
re-instantiated uplink devlink port and related netdevice during devlink
reload. However with migration to auxiliary devices, this behaviour
changed.
Restore the original behaviour and tear down auxiliary devices
completely during devlink reload.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
mlx5_load_one() is always called with recovery==false, so remove the
unneeded function arg.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In case where after reset the PCI link is not ready within timeout, skip
reading device ID as if there is no PCI link up we can't have FW
response to pci config cycles either.
This also fixes err value not used and overwritten in such flow.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Move the param registration and handling code into the fw reset code
as they are related to each other. No point in having the devlink param
registration done in separate file.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When sync reset now event handling fails on mlx5_pci_link_toggle() then
no reset was done. However, since mlx5_cmd_fast_teardown_hca() was
already done, the firmware function is closed and the driver is left
without firmware functionality.
Fix it by setting device error state and reopen the firmware resources.
Reopening is done by the thread that was called for devlink reload
fw_activate as it already holds the devlink lock.
Fixes: 5ec697446f46 ("net/mlx5: Add support for devlink reload action fw activate")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In case PCI reads fail after unload, there is no use in trying to
load the device.
Fixes: 5ec697446f46 ("net/mlx5: Add support for devlink reload action fw activate")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
After firmware reset driver should verify firmware already enabled CRS
and became responsive to pci config cycles before restoring pci state.
Fix that by waiting till device_id is readable through PCI again.
Fixes: eabe8e5e88f5 ("net/mlx5: Handle sync reset now event")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-3-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Refactor fw reset code to have the unload driver part done on
mlx5_fw_reset_complete_reload(), so if it was called by the PF which
initiated the reload fw activate flow, the unload part will be handled
by the mlx5_devlink_reload_fw_activate() callback itself and not by the
reset event work.
This will be used by the downstream patch to invoke devlink reload
callbacks with devlink lock held.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
drivers/net/ethernet/mellanox/mlx5/core/main.c
b33886971dbc ("net/mlx5: Initialize flow steering during driver probe")
40379a0084c2 ("net/mlx5_fpga: Drop INNOVA TLS support")
f2b41b32cde8 ("net/mlx5: Remove ipsec_ops function table")
https://lore.kernel.org/all/20220519040345.6yrjromcdistu7vh@sx1/
16d42d313350 ("net/mlx5: Drain fw_reset when removing device")
8324a02c342a ("net/mlx5: Add exit route when waiting for FW")
https://lore.kernel.org/all/20220519114119.060ce014@canb.auug.org.au/
tools/testing/selftests/net/mptcp/mptcp_join.sh
e274f7154008 ("selftests: mptcp: add subflow limits test-cases")
b6e074e171bc ("selftests: mptcp: add infinite map testcase")
5ac1d2d63451 ("selftests: mptcp: Add tests for userspace PM type")
https://lore.kernel.org/all/20220516111918.366d747f@canb.auug.org.au/
net/mptcp/options.c
ba2c89e0ea74 ("mptcp: fix checksum byte order")
1e39e5a32ad7 ("mptcp: infinite mapping sending")
ea66758c1795 ("tcp: allow MPTCP to update the announced window")
https://lore.kernel.org/all/20220519115146.751c3a37@canb.auug.org.au/
net/mptcp/pm.c
95d686517884 ("mptcp: fix subflow accounting on close")
4d25247d3ae4 ("mptcp: bypass in-kernel PM restrictions for non-kernel PMs")
https://lore.kernel.org/all/20220516111435.72f35dca@canb.auug.org.au/
net/mptcp/subflow.c
ae66fb2ba6c3 ("mptcp: Do TCP fallback on early DSS checksum failure")
0348c690ed37 ("mptcp: add the fallback check")
f8d4bcacff3b ("mptcp: infinite mapping receiving")
https://lore.kernel.org/all/20220519115837.380bb8d4@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case fw sync reset is called in parallel to device removal, device
might stuck in the following deadlock:
CPU 0 CPU 1
----- -----
remove_one
uninit_one (locks intf_state_mutex)
mlx5_sync_reset_now_event()
work in fw_reset->wq.
mlx5_enter_error_state()
mutex_lock (intf_state_mutex)
cleanup_once
fw_reset_cleanup()
destroy_workqueue(fw_reset->wq)
Drain the fw_reset WQ, and make sure no new work is being queued, before
entering uninit_one().
The Drain is done before devlink_unregister() since fw_reset, in some
flows, is using devlink API devlink_remote_reload_actions_performed().
Fixes: 38b9f903f22b ("net/mlx5: Handle sync reset request event")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently, health recovery will reload driver to recover it from fatal
errors. During the driver's load process, it would wait for FW to set the
pre-init bit for up to 120 seconds, beyond this threshold it would abort
the load process. In some cases, such as a FW upgrade on the DPU, this
timeout period is insufficient, and the user has no way to recover the
host device.
To solve this issue, introduce a new FW pre-init timeout for health
recovery, which is set to 2 hours.
The timeout for devlink reload and probe will use the original one because
they are user triggered flows, and therefore should not have a
significantly long timeout, during which the user command would hang.
Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Double clear of reset requested state can lead to NULL pointer as it
will try to delete the timer twice. This can happen for example on a
race between abort from FW and pci error or reset. Avoid such case using
test_and_clear_bit() to verify only one time reset requested state clear
flow. Similarly use test_and_set_bit() to verify only one time reset
requested state set flow.
Fixes: 7dd6df329d4c ("net/mlx5: Handle sync reset abort event")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The sync reset flow can lead to the following deadlock when
poll_sync_reset() is called by timer softirq and waiting on
del_timer_sync() for the same timer. Fix that by moving the part of the
flow that waits for the timer to reset_reload_work.
It fixes the following kernel Trace:
RIP: 0010:del_timer_sync+0x32/0x40
...
Call Trace:
<IRQ>
mlx5_sync_reset_clear_reset_requested+0x26/0x50 [mlx5_core]
poll_sync_reset.cold+0x36/0x52 [mlx5_core]
call_timer_fn+0x32/0x130
__run_timers.part.0+0x180/0x280
? tick_sched_handle+0x33/0x60
? tick_sched_timer+0x3d/0x80
? ktime_get+0x3e/0xa0
run_timer_softirq+0x2a/0x50
__do_softirq+0xe1/0x2d6
? hrtimer_interrupt+0x136/0x220
irq_exit+0xae/0xb0
smp_apic_timer_interrupt+0x7b/0x140
apic_timer_interrupt+0xf/0x20
</IRQ>
Fixes: 3c5193a87b0f ("net/mlx5: Use del_timer_sync in fw reset flow of halting poll")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Maher Sanalla <msanalla@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-next 2022-22-02
The following PR includes updates to mlx5-next branch:
Headlines:
==========
1) Jakub cleans up unused static inline functions
2) I did some low level firmware command interface return status changes to
provide the caller with full visibility on the error/status returned by
the Firmware.
3) Use the new command interface in RDMA DEVX usecases to avoid flooding
dmesg with some "expected" user error prone use cases.
4) Moshe also uses the new command interface to grab the specific error
code from MFRL register command to provide the exact error reason for
why SW reset couldn't perform internally in FW.
5) From Mark Bloch: Lag, drop packets in hardware when possible
In active-backup mode the inactive interface's packets are dropped by the
bond device. In switchdev where TC rules are offloaded to the FDB
this can lead to packets being hit in the FDB where without offload
they would have been dropped before reaching TC rules in the kernel.
Create a drop rule to make sure packets on inactive ports are dropped
before reaching the FDB.
Listen on NETDEV_CHANGEUPPER / NETDEV_CHANGEINFODATA events and record
the inactive state and offload accordingly.
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Add clarification on sync reset failure
net/mlx5: Add reset_state field to MFRL register
RDMA/mlx5: Use new command interface API
net/mlx5: cmdif, Refactor error handling and reporting of async commands
net/mlx5: Use mlx5_cmd_do() in core create_{cq,dct}
net/mlx5: cmdif, Add new api for command execution
net/mlx5: cmdif, cmd_check refactoring
net/mlx5: cmdif, Return value improvements
net/mlx5: Lag, offload active-backup drops to hardware
net/mlx5: Lag, record inactive state of bond device
net/mlx5: Lag, don't use magic numbers for ports
net/mlx5: Lag, use local variable already defined to access E-Switch
net/mlx5: E-switch, add drop rule support to ingress ACL
net/mlx5: E-switch, remove special uplink ingress ACL handling
net/mlx5: E-Switch, reserve and use same uplink metadata across ports
net/mlx5: Add ability to insert to specific flow group
mlx5: remove unused static inlines
====================
Link: https://lore.kernel.org/r/20220223233930.319301-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case devlink reload action fw_activate failed in sync reset stage,
use the new MFRL field reset_state to find why it failed and share this
clarification with the user.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Substitute del_timer() with del_timer_sync() in fw reset polling
deactivation flow, in order to prevent a race condition which occurs
when del_timer() is called and timer is deactivated while another
process is handling the timer interrupt. A situation that led to
the following call trace:
RIP: 0010:run_timer_softirq+0x137/0x420
<IRQ>
recalibrate_cpu_khz+0x10/0x10
ktime_get+0x3e/0xa0
? sched_clock_cpu+0xb/0xc0
__do_softirq+0xf5/0x2ea
irq_exit_rcu+0xc1/0xf0
sysvec_apic_timer_interrupt+0x9e/0xc0
asm_sysvec_apic_timer_interrupt+0x12/0x20
</IRQ>
Fixes: 38b9f903f22b ("net/mlx5: Handle sync reset request event")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
mlx5_tout_ms() returns a u64, we can't directly divide it.
This is not a problem here, @timeout which is the value
that actually matters here is already a ulong, so this
implies storing return value of mlx5_tout_ms() on a ulong
should be fine.
This fixes:
ERROR: modpost: "__udivdi3" [drivers/net/ethernet/mellanox/mlx5/core/mlx5_core.ko] undefined!
Fixes: 32def4120e48 ("net/mlx5: Read timeout values from DTOR")
Link: https://lore.kernel.org/r/20211018172608.1069754-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace hard coded timeouts with values stored by firmware in default
timeouts register (DTOR). Timeouts are read during driver load. If DTOR
is not supported by firmware then fallback to hard coded defaults
instead.
Signed-off-by: Amir Tzin <amirtz@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In case driver sent NACK to firmware on sync reset request, it will get
sync reset abort event while it didn't set sync reset requested mode.
Thus, on abort sync reset event handler, driver should check reset
requested is set before trying to stop sync reset poll.
Fixes: 7dd6df329d4c ("net/mlx5: Handle sync reset abort event")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The FW tracer check is called twice, so delete one of them.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The mix between probe/unprobe and reload flows causes to have an extra
mutex lock intf_state_mutex that generates LOCKDEP warning between it
and devlink_mutex. As a preparation for the future removal, separate
those flows.
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Firmware live patch event notifies the driver that the firmware was just
updated using live patch. In such case the driver should not reload or
re-initiate entities, part to updating the firmware version and
re-initiate the firmware tracer which can be updated by live patch with
new strings database to help debugging an issue.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The enable_remote_dev_reset devlink param flags that the host admin
allows resets by other hosts. In case it is cleared mlx5 host PF driver
will send NACK on pci sync for firmware update reset request and the
command will fail.
By default enable_remote_dev_reset parameter is true, so pci sync for
firmware update reset is enabled.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for devlink reload action fw_activate. To activate firmware
image the mlx5 driver resets the firmware and reloads it from flash. If
a new image was stored on flash it will be loaded. Once this reload
command is executed the driver initiates fw sync reset flow, where the
firmware synchronizes all PFs on coming reset and driver reload.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If firmware sends sync_reset_abort to driver the driver should clear the
reset requested mode as reset is not expected any more.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On sync_reset_now event the driver does reload and PCI link toggle to
activate firmware upgrade reset. When the firmware sends this event it
syncs the event on all PFs, so all PFs will do PCI link toggle at once.
To do PCI link toggle, the driver ensures that no other device ID under
the same bridge by checking that all the PF functions under the same PCI
bridge have same device ID. If no other device it uses PCI bridge link
control to turn link down and up.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Once the driver gets sync_reset_request from firmware it prepares for the
coming reset and sends acknowledge.
After getting this event the driver expects device reset, either it will
trigger PCI reset on sync_reset_now event or such PCI reset will be
triggered by another PF of the same device. So it moves to reset
requested mode and if it gets PCI reset triggered by the other PF it
detect the reset and reloads.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add functions to query and set the MFRL reset options supported by
firmware.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
