summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/mellanox/mlxsw
AgeCommit message (Collapse)AuthorFilesLines
2019-05-25mlxsw: core: Prevent QSFP module initialization for old hardwareVadim Pasternak4-0/+17
[ Upstream commit c52ecff7e6439ca8c9b03282e8869a005aa94831 ] Old Mellanox silicons, like switchx-2, switch-ib do not support reading QSFP modules temperature through MTMP register. Attempt to access this register on systems equipped with the this kind of silicon will cause initialization flow failure. Test for hardware resource capability is added in order to distinct between old and new silicon - old silicons do not have such capability. Fixes: 6a79507cfe94 ("mlxsw: core: Extend thermal module with per QSFP module thermal zones") Fixes: 5c42eaa07bd0 ("mlxsw: core: Extend hwmon interface with QSFP module temperature attributes") Reported-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-18mlxsw: spectrum: Fix autoneg status in ethtoolAmit Cohen1-2/+2
If link is down and autoneg is set to on/off, the status in ethtool does not change. The reason is when the link is down the function returns with zero before changing autoneg value. Move the checking of link state (up/down) to be performed after setting autoneg value, in order to be sure that autoneg will change in any case. Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Amit Cohen <amitc@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-18mlxsw: pci: Reincrease PCI reset timeoutIdo Schimmel1-1/+1
During driver initialization the driver sends a reset to the device and waits for the firmware to signal that it is ready to continue. Commit d2f372ba0914 ("mlxsw: pci: Increase PCI SW reset timeout") increased the timeout to 13 seconds due to longer PHY calibration in Spectrum-2 compared to Spectrum-1. Recently it became apparent that this timeout is too short and therefore this patch increases it again to a safer limit that will be reduced in the future. Fixes: c3ab435466d5 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC") Fixes: d2f372ba0914 ("mlxsw: pci: Increase PCI SW reset timeout") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-18mlxsw: spectrum: Put MC TCs into DWRR modePetr Machata1-1/+1
Both Spectrum-1 and Spectrum-2 chips are currently configured such that pairs of TC n (which is used for UC traffic) and TC n+8 (which is used for MC traffic) are feeding into the same subgroup. Strict prioritization is configured between the two TCs, and by enabling MC-aware mode on the switch, the lower-numbered (UC) TCs are favored over the higher-numbered (MC) TCs. On Spectrum-2 however, there is an issue in configuration of the MC-aware mode. As a result, MC traffic is prioritized over UC traffic. To work around the issue, configure the MC TCs with DWRR mode (while keeping the UC TCs in strict mode). With this patch, the multicast-unicast arbitration results in the same behavior on both Spectrum-1 and Spectrum-2 chips. Fixes: 7b8195306694 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports") Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-10mlxsw: spectrum_buffers: Add a multicast pool for Spectrum-2Ido Schimmel1-8/+11
In Spectrum-1, when a multicast packet is admitted to the shared buffer it increases the quotas of all the ports and {port, TC} to which it is forwarded to. The above means that multicast packets are accounted multiple times in the shared buffer and can therefore cause the associated shared buffer pool to fill up very quickly. To work around this issue, commit e83c045e53d7 ("mlxsw: spectrum_buffers: Configure MC pool") added a dedicated multicast pool in which multicast packets are accounted. The issue is not present in Spectrum-2, but in order to be backward compatible with Spectrum-1, its default behavior is to allow a multicast packet to increase multiple egress quotas instead of one. Until the new (non-backward compatible) mode is supported, configure a dedicated multicast pool as in Spectrum-1. Fixes: fe099bf682ab ("mlxsw: spectrum_buffers: Add Spectrum-2 shared buffer configuration") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-10mlxsw: spectrum_router: Do not check VRF MAC addressIdo Schimmel1-1/+1
Commit 74bc99397438 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses") enabled the driver to veto router interface (RIF) MAC addresses that it cannot support. This check should only be performed for interfaces for which the driver actually configures a RIF. A VRF upper is not one of them, so ignore it. Without this patch it is not possible to set an IP address on the VRF device and use it as a loopback. Fixes: 74bc99397438 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Alexander Petrovskiy <alexpe@mellanox.com> Tested-by: Alexander Petrovskiy <alexpe@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-10mlxsw: core: Do not use WQ_MEM_RECLAIM for mlxsw workqueueIdo Schimmel1-1/+1
The workqueue is used to periodically update the networking stack about activity / statistics of various objects such as neighbours and TC actions. It should not be called as part of memory reclaim path, so remove the WQ_MEM_RECLAIM flag. Fixes: 3d5479e92087 ("mlxsw: core: Remove deprecated create_workqueue") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-10mlxsw: core: Do not use WQ_MEM_RECLAIM for mlxsw ordered workqueueIdo Schimmel1-1/+1
The ordered workqueue is used to offload various objects such as routes and neighbours in the order they are notified. It should not be called as part of memory reclaim path, so remove the WQ_MEM_RECLAIM flag. This can also result in a warning [1], if a worker tries to flush a non-WQ_MEM_RECLAIM workqueue. [1] [97703.542861] workqueue: WQ_MEM_RECLAIM mlxsw_core_ordered:mlxsw_sp_router_fib6_event_work [mlxsw_spectrum] is flushing !WQ_MEM_RECLAIM events:rht_deferred_worker [97703.542884] WARNING: CPU: 1 PID: 32492 at kernel/workqueue.c:2605 check_flush_dependency+0xb5/0x130 ... [97703.542988] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018 [97703.543049] Workqueue: mlxsw_core_ordered mlxsw_sp_router_fib6_event_work [mlxsw_spectrum] [97703.543061] RIP: 0010:check_flush_dependency+0xb5/0x130 ... [97703.543071] RSP: 0018:ffffb3f08137bc00 EFLAGS: 00010086 [97703.543076] RAX: 0000000000000000 RBX: ffff96e07740ae00 RCX: 0000000000000000 [97703.543080] RDX: 0000000000000094 RSI: ffffffff82dc1934 RDI: 0000000000000046 [97703.543084] RBP: ffffb3f08137bc20 R08: ffffffff82dc18a0 R09: 00000000000225c0 [97703.543087] R10: 0000000000000000 R11: 0000000000007eec R12: ffffffff816e4ee0 [97703.543091] R13: ffff96e06f6a5c00 R14: ffff96e077ba7700 R15: ffffffff812ab0c0 [97703.543097] FS: 0000000000000000(0000) GS:ffff96e077a80000(0000) knlGS:0000000000000000 [97703.543101] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [97703.543104] CR2: 00007f8cd135b280 CR3: 00000001e860e003 CR4: 00000000003606e0 [97703.543109] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [97703.543112] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [97703.543115] Call Trace: [97703.543129] __flush_work+0xbd/0x1e0 [97703.543137] ? __cancel_work_timer+0x136/0x1b0 [97703.543145] ? pwq_dec_nr_in_flight+0x49/0xa0 [97703.543154] __cancel_work_timer+0x136/0x1b0 [97703.543175] ? mlxsw_reg_trans_bulk_wait+0x145/0x400 [mlxsw_core] [97703.543184] cancel_work_sync+0x10/0x20 [97703.543191] rhashtable_free_and_destroy+0x23/0x140 [97703.543198] rhashtable_destroy+0xd/0x10 [97703.543254] mlxsw_sp_fib_destroy+0xb1/0xf0 [mlxsw_spectrum] [97703.543310] mlxsw_sp_vr_put+0xa8/0xc0 [mlxsw_spectrum] [97703.543364] mlxsw_sp_fib_node_put+0xbf/0x140 [mlxsw_spectrum] [97703.543418] ? mlxsw_sp_fib6_entry_destroy+0xe8/0x110 [mlxsw_spectrum] [97703.543475] mlxsw_sp_router_fib6_event_work+0x6cd/0x7f0 [mlxsw_spectrum] [97703.543484] process_one_work+0x1fd/0x400 [97703.543493] worker_thread+0x34/0x410 [97703.543500] kthread+0x121/0x140 [97703.543507] ? process_one_work+0x400/0x400 [97703.543512] ? kthread_park+0x90/0x90 [97703.543523] ret_from_fork+0x35/0x40 Fixes: a3832b31898f ("mlxsw: core: Create an ordered workqueue for FIB offload") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Semion Lisyansky <semionl@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-10mlxsw: core: Do not use WQ_MEM_RECLAIM for EMAD workqueueIdo Schimmel1-1/+1
The EMAD workqueue is used to handle retransmission of EMAD packets that contain configuration data for the device's firmware. Given the workers need to allocate these packets and that the code is not called as part of memory reclaim path, remove the WQ_MEM_RECLAIM flag. Fixes: d965465b60ba ("mlxsw: core: Fix possible deadlock") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-10mlxsw: spectrum_switchdev: Add MDB entries in prepare phaseIdo Schimmel1-1/+1
The driver cannot guarantee in the prepare phase that it will be able to write an MDB entry to the device. In case the driver returned success during the prepare phase, but then failed to add the entry in the commit phase, a WARNING [1] will be generated by the switchdev core. Fix this by doing the work in the prepare phase instead. [1] [ 358.544486] swp12s0: Commit of object (id=2) failed. [ 358.550061] WARNING: CPU: 0 PID: 30 at net/switchdev/switchdev.c:281 switchdev_port_obj_add_now+0x9b/0xe0 [ 358.560754] CPU: 0 PID: 30 Comm: kworker/0:1 Not tainted 5.0.0-custom-13382-gf2449babf221 #1350 [ 358.570472] Hardware name: Mellanox Technologies Ltd. MSN2100-CB2FO/SA001017, BIOS 5.6.5 06/07/2016 [ 358.580582] Workqueue: events switchdev_deferred_process_work [ 358.587001] RIP: 0010:switchdev_port_obj_add_now+0x9b/0xe0 ... [ 358.614109] RSP: 0018:ffffa6b900d6fe18 EFLAGS: 00010286 [ 358.619943] RAX: 0000000000000000 RBX: ffff8b00797ff000 RCX: 0000000000000000 [ 358.627912] RDX: ffff8b00b7a1d4c0 RSI: ffff8b00b7a152e8 RDI: ffff8b00b7a152e8 [ 358.635881] RBP: ffff8b005c3f5bc0 R08: 000000000000022b R09: 0000000000000000 [ 358.643850] R10: 0000000000000000 R11: ffffa6b900d6fcc8 R12: 0000000000000000 [ 358.651819] R13: dead000000000100 R14: ffff8b00b65a23c0 R15: 0ffff8b00b7a2200 [ 358.659790] FS: 0000000000000000(0000) GS:ffff8b00b7a00000(0000) knlGS:0000000000000000 [ 358.668820] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 358.675228] CR2: 00007f00aad90de0 CR3: 00000001ca80d000 CR4: 00000000001006f0 [ 358.683188] Call Trace: [ 358.685918] switchdev_port_obj_add_deferred+0x13/0x60 [ 358.691655] switchdev_deferred_process+0x6b/0xf0 [ 358.696907] switchdev_deferred_process_work+0xa/0x10 [ 358.702548] process_one_work+0x1f5/0x3f0 [ 358.707022] worker_thread+0x28/0x3c0 [ 358.711099] ? process_one_work+0x3f0/0x3f0 [ 358.715768] kthread+0x10d/0x130 [ 358.719369] ? __kthread_create_on_node+0x180/0x180 [ 358.724815] ret_from_fork+0x35/0x40 Fixes: 3a49b4fde2a1 ("mlxsw: Adding layer 2 multicast support") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Alex Kushnarov <alexanderk@mellanox.com> Tested-by: Alex Kushnarov <alexanderk@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-19mlxsw: core: mlxsw: core: avoid -Wint-in-bool-context warningArnd Bergmann1-1/+1
A recently added function in mlxsw triggers a harmless compiler warning: In file included from drivers/net/ethernet/mellanox/mlxsw/core.h:17, from drivers/net/ethernet/mellanox/mlxsw/core_env.c:7: drivers/net/ethernet/mellanox/mlxsw/core_env.c: In function 'mlxsw_env_module_temp_thresholds_get': drivers/net/ethernet/mellanox/mlxsw/reg.h:8015:45: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context] #define MLXSW_REG_MTMP_TEMP_TO_MC(val) (val * 125) ~~~~~^~~~~~ drivers/net/ethernet/mellanox/mlxsw/core_env.c:116:8: note: in expansion of macro 'MLXSW_REG_MTMP_TEMP_TO_MC' if (!MLXSW_REG_MTMP_TEMP_TO_MC(module_temp)) { ^~~~~~~~~~~~~~~~~~~~~~~~~ The warning is normally disabled, but it would be nice to enable it to find real bugs, and there are no other known instances at the moment. Replace the negation with a zero-comparison, which also matches the comment above it. Fixes: d93c19a1d95c ("mlxsw: core: Add API for QSFP module temperature thresholds reading") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-13mlxsw: minimal: Initialize base_macJiri Pirko1-0/+18
Currently base_mac is not initialized which causes wrong reporting of zeroed parent_id to userspace. Fix this by initializing base_mac properly. Fixes: c100e47caa8e ("mlxsw: minimal: Add ethtool support") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-13mlxsw: core: Prevent duplication during QSFP module initializationVadim Pasternak1-10/+11
Verify during thermal initialization if QSFP module's entry is already configured in order to prevent duplication. Such scenario could happen in case two switch drivers (PCI and I2C based) coexist and if after boot, splitting configuration is applied for some ports and then I2C based driver is re-probed. In such case after reboot same QSFP module, associated with split will be discovered by I2C based driver few times, and it will cause a crash. It could happen for example on system equipped with BMC (Baseboard Management Controller), running I2C based driver, when the next steps are performed: - System boot - Host side configures port spilt. - BMC side is rebooted. Fixes: 6a79507cfe94 ("mlxsw: core: Extend thermal module with per QSFP module thermal zones") Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-04mellanox: Switch to bitmap_zalloc()Andy Shevchenko1-4/+3
Switch to bitmap_zalloc() to show clearly what we are allocating. Besides that it returns pointer of bitmap type instead of opaque void *. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-04mlxsw: i2c: Extend initialization by querying resources dataVadim Pasternak2-6/+17
Extend initialization flow by query requests for chip resources data in order to obtain chip's specific capabilities, like the number of ports. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-04mlxsw: i2c: Extend input parameters list of command APIVadim Pasternak1-19/+101
Extend input parameters list of command API in mlxsw_i2c_cmd() in order to support initialization commands. Up until now, only access commands were supported by I2C driver. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-04mlxsw: i2c: Modify input parameter name in initialization APIVadim Pasternak1-1/+1
Change input parameter name "resource" to "res" in mlxsw_i2c_init() in order to align it with mlxsw_pci_init(). Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-04mlxsw: i2c: Fix comment misspellingVadim Pasternak1-1/+1
Fix comment for mlxsw_i2c_write_cmd(). Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-04mlxsw: core: Move resource query API to common locationVadim Pasternak3-37/+40
Move mlxsw_pci_resources_query() to a common location to allow reuse by the different drivers and over all the supported physical buses. Rename it to mlxsw_core_resources_query(). Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-04mlxsw: minimal: Add ethtool supportVadim Pasternak1-2/+322
The minimal driver is chip independent and uses I2C bus for chip access. Its purpose is to support chassis management on systems equipped with Mellanox switch ASICs. For example from BMC (Board Management Controller) device. Expose a dummy netdev for each front panel port and implement basic ethtool operations to obtain QSFP/SFP module info through ethtool. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-04mlxsw: minimal: Make structures and variables names shorterVadim Pasternak1-18/+18
Replace "mlxsw_minimal" by "mlxsw_m" in order to improve code readability. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-04mlxsw: core: Move ethtool module callbacks to a common locationVadim Pasternak3-107/+139
Move the implementation of ethtool module callbacks - .get_module_info() and .get_module_eeprom() - to a common location to allow reuse by the different mlxsw drivers. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02mlxsw: spectrum_acl: Make mlxsw_sp_acl_tcam_vregion_rehash() return voidJiri Pirko1-8/+4
The return value is ignored anyway, so just return void. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02mlxsw: spectrum_acl: Remember where to continue rehash migrationJiri Pirko1-5/+86
Store pointer to vchunk where the migration was interrupted, as well as ventry pointer to start from and to stop at (during rollback). This saved pointers need to be forgotten in case of ventries list or vchunk list changes, which is done by couple of "changed" helpers. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02mlxsw: spectrum_acl: Allow to interrupt/continue rehash workJiri Pirko1-20/+62
Currently, migration of vregions with many entries may take long time during which insertions and removals of the rules are blocked due to wait to acquire vregion->lock. To overcome this, allow to interrupt and continue rehash work according to the set credits - number of rules to migrate. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02mlxsw: spectrum_acl: Do rollback as another call to ↵Jiri Pirko1-46/+29
mlxsw_sp_acl_tcam_vchunk_migrate_all() In order to simplify the code and to prepare it for interrupted/continued migration process, do the rollback in case of migration error as another call to mlxsw_sp_acl_tcam_vchunk_migrate_all(). It can be understood as "migrate all back". Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02mlxsw: spectrum_acl: Put vchunk migrate start/end code into separate functionsJiri Pirko1-11/+32
In preparations of interrupt/continue of rehash work, put the code that is done at the beginning/end of vchunk migrate function into separate functions. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02mlxsw: spectrum_acl: Put this_is_rollback to rehash context structJiri Pirko1-7/+12
Put the this_is_rollback flag into rehash context struct in preparations for interrupt/continue of rehash work. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02mlxsw: spectrum_acl: Rename variables in mlxsw_sp_acl_tcam_ventry_migrate()Jiri Pirko1-7/+7
Remove some of variables in function mlxsw_sp_acl_tcam_ventry_migrate() so the names are aligned with the rest of the code. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02mlxsw: spectrum_acl: assign vchunk->chunk by the newly created chunkJiri Pirko1-8/+10
Make the vchunk->chunk contain pointer of a new chunk we migrate to. In case of a rollback, it contains the original chunk. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02mlxsw: spectrum_acl: assign vregion->region by the newly created regionJiri Pirko1-22/+20
Make the vregion->region contain pointer of a new region we migrate to. In case of a rollback, it contains the original region. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02mlxsw: spectrum_acl: Push code start/end from ↵Jiri Pirko1-39/+35
mlxsw_sp_acl_tcam_vregion_migrate() Push code from the beginning and end of function mlxsw_sp_acl_tcam_vregion_migrate() into rehash_start()/end() functions. Then all the things needed to be done before and after the actual migration process will be grouped together. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02mlxsw: spectrum_acl: Push rehash start/end code into separate functionsJiri Pirko1-9/+32
In preparations for interrupt/continue of rehash work, put the code at the beginning/end of the rehash function into separate functions. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02mlxsw: spectrum_acl: Introduce new rehash context struct and save hint_priv ↵Jiri Pirko1-4/+12
there Prepare for continued migration. Introduce a new structure to track rehash context and save hint_priv into it. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02mlxsw: spectrum_acl: Don't migrate already migrated entryJiri Pirko1-0/+4
Check if the entry is already in a chunk where we want it to be. In that case, skip migration. This is preparation for "per parts" migration where this situation may occur. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02mlxsw: spectrum_acl: Push rehash dw struct into rehash sub-structJiri Pirko1-7/+9
More rehash related fields are going to come. Push "dw" into sub-struct that will accommodate the others as well. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-27route: Add multipath_hash in flowi_common to make user-define hashwenxu1-1/+1
Current fib_multipath_hash_policy can make hash based on the L3 or L4. But it only work on the outer IP. So a specific tunnel always has the same hash value. But a specific tunnel may contain so many inner connections. This patch provide a generic multipath_hash in floi_common. It can make a user-define hash which can mix with L3 or L4 hash. Signed-off-by: wenxu <wenxu@ucloud.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-27net: Remove switchdev_opsFlorian Fainelli3-17/+0
Now that we have converted all possible callers to using a switchdev notifier for attributes we do not have a need for implementing switchdev_ops anymore, and this can be removed from all drivers the net_device structure. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-27mlxsw: spectrum_switchdev: Handle SWITCHDEV_PORT_ATTR_SETFlorian Fainelli1-0/+12
Following patches will change the way we communicate setting a port's attribute and use a notifier to perform those tasks. Prepare mlxsw to support receiving notifier events targeting SWITCHDEV_PORT_ATTR_SET and utilize the switchdev_handle_port_attr_set() to handle stacking of devices. Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-26mlxsw: spectrum: remove set but not used variable 'autoneg_status'YueHaibing1-3/+0
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function 'mlxsw_sp_port_get_link_ksettings': drivers/net/ethernet/mellanox/mlxsw/spectrum.c:3062:5: warning: variable 'autoneg_status' set but not used [-Wunused-but-set-variable] It's not used since commit 475b33cb66c9 ("mlxsw: spectrum: Remove unsupported eth_proto_lp_advertise field in PTYS") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-26net: devlink: turn devlink into a built-inJakub Kicinski1-1/+0
Being able to build devlink as a module causes growing pains. First all drivers had to add a meta dependency to make sure they are not built in when devlink is built as a module. Now we are struggling to invoke ethtool compat code reliably. Make devlink code built-in, users can still not build it at all but the dynamically loadable module option is removed. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-26mlxsw: spectrum: acl: Use struct_size() in kzalloc()Gustavo A. R. Silva1-4/+2
One of the more common cases of allocation size calculations is finding the size of a structure that has a zero-sized array at the end, along with memory for some number of elements for that array. For example: struct foo { int stuff; struct boo entry[]; }; size = sizeof(struct foo) + count * sizeof(struct boo); instance = kzalloc(size, GFP_KERNEL) Instead of leaving these open-coded and prone to type mistakes, we can now use the new struct_size() helper: instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL) Notice that, in this case, variable alloc_size is not necessary, hence it is removed. This code was detected with the help of Coccinelle. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25mlxsw: spectrum_acl: Add vregion migration end tracepointJiri Pirko1-3/+8
Hit the new tracepoint once the vregion migration ends. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25mlxsw: spectrum_acl: Don't take mutex in mlxsw_sp_acl_tcam_vregion_rehash_work()Jiri Pirko1-5/+0
Other mutexes are taking care of proper locking for this, no longer needed to take RTNL mutex here. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25mlxsw: spectrum_acl: Remove RTNL lock assertions from ERP codeJiri Pirko1-6/+0
No longer require RTNL lock in this code. Newly introduced mutexes take care of guarding objagg and bloom filter. There is no need to guard gen_pool_alloc()/gen_pool_free() as they are fine to be called lockless. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25mlxsw: spectrum_acl: Don't take rtnl lock during vregion_rehash_intrvl_set()Jiri Pirko2-2/+10
Relax dependency on rtnl mutex during vregion_rehash_intrvl_set(). The vregion list is protected with newly introduced mutex. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25mlxsw: spectrum_acl: Introduce a mutex to guard objagg instance manipulationJiri Pirko1-5/+20
Protect objagg structures by adding a mutex to ERP code and take it during the structure manipulation. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25mlxsw: spectrum_acl: Enable vregion rehash per-profileJiri Pirko1-8/+15
For MR ACL profile is does not make sense to do periodical rehashes, as there is only one mask in use during the whole vregion lifetime. Therefore periodical work is scheduled but the rehash never happens. So allow to enable/disable rehash for the whole group, which is added per-profile. Disable rehashing for MR profile. Addition to the vregion list is done only in case the rehash is enable on the particular vregion. Also, the addition is moved after delayed work init to avoid schedule of uninitialized work from vregion_rehash_intrvl_set(). Symmetrically, deletion from the list is done before canceling the delayed work so it is not scheduled by vregion_rehash_intrvl_set() again. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25mlxsw: spectrum_acl: Introduce mutex to guard Bloom Filter updatesJiri Pirko1-7/+27
Bloom filter is shared within multiple regions. For updates, it needs to be guarded by a separate mutex. Do that in order to not rely on RTNL mutex. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25mlxsw: spectrum_acl: Introduce vregion mutexJiri Pirko1-0/+26
In order to remove dependency on RTNL, introduce a mutex to guard vregion structure, list of chunks and list of entries in chunks. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2024-09-07 09:42:52 +0300