| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, there are lots of minor driver changes across SoC platforms
from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
These usually add support for additional chip variations in existing
drivers, but also add features or bugfixes.
The SCMI firmware subsystem gains a unified raw userspace interface
through debugfs, which can be used for validation purposes.
Newly added drivers include:
- New power management drivers for StarFive JH7110, Allwinner D1 and
Renesas RZ/V2M
- A driver for Qualcomm battery and power supply status
- A SoC device driver for identifying Nuvoton WPCM450 chips
- A regulator coupler driver for Mediatek MT81xxv"
* tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
power: supply: Introduce Qualcomm PMIC GLINK power supply
soc: apple: rtkit: Do not copy the reg state structure to the stack
soc: sunxi: SUN20I_PPU should depend on PM
memory: renesas-rpc-if: Remove redundant division of dummy
soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
MAINTAINERS: Update qcom CPR maintainer entry
dt-bindings: firmware: document Qualcomm SM8550 SCM
dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
soc: qcom: socinfo: Add support for new field in revision 17
soc: qcom: smd-rpm: Add IPQ9574 compatible
soc: qcom: pmic_glink: remove redundant calculation of svid
soc: qcom: stats: Populate all subsystem debugfs files
dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
soc: qcom: pmic_glink: Introduce altmode support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Consolidate iommu_map/unmap functions.
There have been blocking and atomic variants so far, but that was
problematic as this approach does not scale with required new
variants which just differ in the GFP flags used. So Jason
consolidated this back into single functions that take a GFP
parameter.
- Retire the detach_dev() call-back in iommu_ops
- Arm SMMU updates from Will:
- Device-tree binding updates:
- Cater for three power domains on SM6375
- Document existing compatible strings for Qualcomm SoCs
- Tighten up clocks description for platform-specific
compatible strings
- Enable Qualcomm workarounds for some additional platforms that
need them
- Intel VT-d updates from Lu Baolu:
- Add Intel IOMMU performance monitoring support
- Set No Execute Enable bit in PASID table entry
- Two performance optimizations
- Fix PASID directory pointer coherency
- Fix missed rollbacks in error path
- Cleanups
- Apple t8110 DART support
- Exynos IOMMU:
- Implement better fault handling
- Error handling fixes
- Renesas IPMMU:
- Add device tree bindings for r8a779g0
- AMD IOMMU:
- Various fixes for handling on SNP-enabled systems and
handling of faults with unknown request-ids
- Cleanups and other small fixes
- Various other smaller fixes and cleanups
* tag 'iommu-updates-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (71 commits)
iommu/amd: Skip attach device domain is same as new domain
iommu: Attach device group to old domain in error path
iommu/vt-d: Allow to use flush-queue when first level is default
iommu/vt-d: Fix PASID directory pointer coherency
iommu/vt-d: Avoid superfluous IOTLB tracking in lazy mode
iommu/vt-d: Fix error handling in sva enable/disable paths
iommu/amd: Improve page fault error reporting
iommu/amd: Do not identity map v2 capable device when snp is enabled
iommu: Fix error unwind in iommu_group_alloc()
iommu/of: mark an unused function as __maybe_unused
iommu: dart: DART_T8110_ERROR range should be 0 to 5
iommu/vt-d: Enable IOMMU perfmon support
iommu/vt-d: Add IOMMU perfmon overflow handler support
iommu/vt-d: Support cpumask for IOMMU perfmon
iommu/vt-d: Add IOMMU perfmon support
iommu/vt-d: Support Enhanced Command Interface
iommu/vt-d: Retrieve IOMMU perfmon capability information
iommu/vt-d: Support size of the register set in DRHD
iommu/vt-d: Set No Execute Enable bit in PASID table entry
iommu/vt-d: Remove sva from intel_svm_dev
...
|
|
Starting at IPA v5.0, the number of event rings per EE is defined
in a field in a new HW_PARAM_4 GSI register rather than HW_PARAM_2.
Define this new register and its fields, and update the code that
checks the number of rings supported by hardware to use the proper
field based on IPA version.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Starting with IPA v5.0, a channel's event ring index is encoded in
a field in the CH_C_CNTXT_1 GSI register rather than CH_C_CNTXT_0.
Define a new field ID for the former register and encode the event
ring in the appropriate register.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The GSI channel protocol field in the CH_C_CNTXT_0 GSI register is
widened starting IPA v5.0, making the CHTYPE_PROTOCOL_MSB field
added in IPA v4.5 unnecessary. Update the code to reflect this.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Now that we explicitly define each register field width there is no
need to have a special encoding function for the event ring length.
Add a field for this to the EV_CH_E_CNTXT_1 GSI register, and use it
in place of ev_ch_e_cntxt_1_length_encode() (which can be removed).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Starting at IPA v4.5, almost all GSI registers had their offsets
changed by a fixed amount (shifted downward by 0xd000). Rather than
defining offsets for all those registers dependent on version, an
adjustment was applied for most register accesses. This was
implemented in commit cdeee49f3ef7f ("net: ipa: adjust GSI register
addresses"). It was later modified to be a bit more obvious about
the adjusment, in commit 571b1e7e58ad3 ("net: ipa: use a separate
pointer for adjusted GSI memory").
We now are able to define every GSI register with its own offset, so
there's no need to implement this special adjustment.
So get rid of the "virt_raw" pointer, and just maintain "virt" as
the (non-adjusted) base address of I/O mapped GSI register memory.
Redefine the offsets of all GSI registers (other than the INTER_EE
ones, which were not subject to the adjustment) for IPA v4.5+,
subtracting 0xd000 from their defined offsets instead.
Move the ERROR_LOG and ERROR_LOG_CLR definitions further down in the
register definition files so all registers are defined in order of
their offset.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
I spotted an error in a patch posted this week, unfortunately just
after it got accepted. The effect of the bug is that time-based
interrupt moderation is disabled. This is not technically a bug,
but it is not what is intended. The problem is that a |= assignment
got implemented as a simple assignment, so the previously assigned
value was ignored.
Fixes: edc6158b18af ("net: ipa: define fields for event-ring related registers")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
'x86/vt-d', 'x86/amd' and 'core' into next
|
|
Define field IDs for the remaining GSI registers, and populate the
register definition files accordingly. Use the reg_*() functions to
access field values for those regiters, and get rid of the previous
field definition constants.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The next patch adds a GSI register field that is only valid starting
at IPA v4.11. Create "gsi_v4.11.c" from "gsi_v4.9.c", changing only
the name of the public regs structure it defines.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Define field IDs for the EV_CH_E_CNTXT_0 and EV_CH_E_CNTXT_8 GSI
registers, and populate the register definition files accordingly.
Use the reg_*() functions to access field values for those regiters,
and get rid of the previous field definition constants.
The remaining EV_CH_E_CNTXT_* registers are written with full 32-bit
values (and have no fields).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Beyond the CH_C_QOS register, two other registers whose offset is
related to channel number have fields within them.
Define the fields within the CH_C_CNTXT_0 GSI register, using an
enumerated type to identify the register's fields, and define an
array of field masks to use for that register's reg structure.
For the CH_C_CNTXT_1 GSI register, ch_c_cntxt_1_length_encode()
previously hid the difference in bit width in the channel ring
length field. Instead, define a new field CH_R_LENGTH and encode
the ring size with reg_encode().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Define the fields within the CH_C_QOS GSI register using an array of
field masks in that register's reg structure. Use the reg functions
for encoding values in those fields.
One field in the register is present for IPA v4.0-4.2 only, two
others are present starting at IPA v4.5, and one more is there
starting at IPA v4.9.
Drop the "GSI_" prefix in symbols defined in the gsi_prefetch_mode
enumerated type, and define their values using decimal rather than
hexidecimal values.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Create "gsi_v4.0.c", "gsi_v4.5.c", and "gsi_v4.9.c" as essentially
identical copies of "gsi_v3.5.1.c". The only difference is the name
of the exported "gsi_regs_vX_Y" structure. The next patch will
start differentiating them.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/drivers
More Qualcomm driver updates for 6.3
The qcom_scm.h file is moved into firmware/qcom, to avoid having any
Qualcomm-specific files directly in include/linux.
Support for PMIC GLINK is introduced, which on newer Qualcomm platforms
provides an interface to the firmware implementing battery management
and USB Type-C handling. Together with the base driver comes the custom
altmode support driver.
SMD RPM gains support for IPQ9574, and socinfo is extended with support
for revision 17 of the information format and soc_id for IPQ5332 and
IPQ8064 are added.
The qcom_stats is changes not to fail when not all parts are
initialized.
* tag 'qcom-drivers-for-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
MAINTAINERS: Update qcom CPR maintainer entry
dt-bindings: firmware: document Qualcomm SM8550 SCM
dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
soc: qcom: socinfo: Add support for new field in revision 17
soc: qcom: smd-rpm: Add IPQ9574 compatible
soc: qcom: pmic_glink: remove redundant calculation of svid
soc: qcom: stats: Populate all subsystem debugfs files
dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
soc: qcom: pmic_glink: Introduce altmode support
soc: qcom: pmic_glink: Introduce base PMIC GLINK driver
dt-bindings: soc: qcom: Introduce PMIC GLINK binding
soc: qcom: dcc: Drop driver for now
Link: https://lore.kernel.org/r/20230210182242.2023901-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add the remaining GSI register offset definitions. Use gsi_reg()
rather than the corresponding GSI_*_OFFSET() macros to get the
offsets for these registers, and get rid of the macros.
Note that we are now defining information for the HW_PARAM_2
register, and that doesn't appear until IPA v3.5.1.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The next patch adds a GSI register field that is only valid starting
at IPA v3.5.1. Create "gsi_v3.5.1.c" from "gsi_v3.1.c", changing
only the name of the public regs structure it defines.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add definitions of the offsets for IRQ-related GSI registers. Use
gsi_reg() rather than the corresponding GSI_CNTXT_*_OFFSET() macros
to get the offsets for these registers, and get rid of the macros.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add definitions of the offsets and strides for registers whose
offset depends on an event ring ID, and use gsi_reg() and its
returned value to determine offsets for these registers. Get
rid of the corresponding GSI_EV_CH_E_*_OFFSET() macros.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Continue populating with GSI register definitions, adding remaining
registers whose offset depends on a channel ID. Use gsi_reg() and
reg_n_offset() to determine offsets for those registers, and get rid
of the corresponding GSI_CH_C_*_OFFSET() macros.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a new register definition file in the "reg" subdirectory,
and begin populating it with GSI register definitions based on IPA
version. The GSI registers haven't changed much, so several IPA
versions can share the same GSI register definitions.
As with IPA registers, an array of pointers indexed by GSI register ID
refers to these register definitions, and a new "regs" field in the
GSI structure is initialized in gsi_reg_init() to refer to register
information based on the IPA version (though for now there's only
one). The new function gsi_reg() returns register information for
a given GSI register, and the result can be used to look up that
register's offset.
This patch is meant only to put the infrastructure in place, so only
eon register (CH_C_QOS) is defined for each version, and only the
offset and stride are defined for that register. Use new function
gsi_reg() to look up that register's information to get its offset,
This makes the GSI_CH_C_QOS_OFFSET() unnecessary, so get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a new gsi_reg_id enumerated type, which identifies each GSI
register with a symbolic identifier.
Create a function that indicates whether a register ID is valid.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a new source file "gsi_reg.c", and in it, introduce a new
function to encapsulate initializing GSI registers, including
looking up and I/O mapping their memory.
Create gsi_reg_exit() as the inverse of the init function.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename functions related to register fields so they don't appear to
be IPA-specific, and move their definitions into "reg.h":
ipa_reg_fmask() -> reg_fmask()
ipa_reg_bit() -> reg_bit()
ipa_reg_field_max() -> reg_field_max()
ipa_reg_encode() -> reg_encode()
ipa_reg_decode() -> reg_decode()
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename ipa_reg_offset() to be reg_offset() and move its definition
to "reg.h". Rename ipa_reg_n_offset() to be reg_n_offset() also.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPA register definitions have evolved with each new version. The
changes required to support more than 32 endpoints in IPA v5.0 made
it best to define a unified mechanism for defining registers and
their fields.
GSI register definitions, meanwhile, have remained fairly stable.
And even as the total number of IPA endpoints goes beyond 32, the
number of GSI channels on a given EE that underly endpoints still
remains 32 or less.
Despite that, GSI v3.0 (which is used with IPA v5.0) extends the
number of channels (and events) it supports to be about 256, and as
a result, many GSI register definitions must change significantly.
To address this, we'll use the same "ipa_reg" mechanism to define
the GSI registers.
As a first step in generalizing the "ipa_reg" to also support GSI
registers, isolate the definitions of the "ipa_reg" and "ipa_regs"
structure types (and some supporting macros) into a new header file,
and remove the "ipa_" and "IPA_" from symbol names.
Separate the IPA register ID validity checking from the generic
check that a register ID is in range. Aside from that, this is
intended to have no functional effect on the code.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move some static inline function definitions out of "gsi_reg.h" and
into "gsi.c", which is the only place they're used. Rename them so
their names identify the register they're associated with.
Move the gsi_channel_type enumerated type definition below the
offset and field definitions for the CH_C_CNTXT_0 register where
it's used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are seven GSI interrupt types that can be signaled by a single
GSI IRQ. These are represented in a bitmask, and the gsi_irq_type_id
enumerated type defines what each bit position represents.
Similarly, the global and general GSI interrupt types each has a set
of conditions it signals, and both types have an enumerated type
that defines which bit that represents each condition.
When used, these enumerated values are passed as an argument to BIT()
in *all* cases. So clean up the code a little bit by defining the
enumerated type values as one-bit masks rather than bit positions.
Rename gsi_general_id to be gsi_general_irq_id for consistency.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When checking the validity of an IPA register ID, compare it against
all possible ipa_reg_id values.
Rename the function ipa_reg_id_valid() to be specific about what's
being checked.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Soon IPA v5.0+ will be supported, and when that happens we will be
able to enable support for the SDX65 (IPA v5.0), SM8450 (IPA v5.1),
and SM8550 (IPA v5.5).
Fix the comment about the GSI version used for IPA v3.1.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reg_addr field in the IPA structure is set but never used.
Get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Starting at IPA v4.11, the GSI_GENERIC_COMMAND GSI register got a
new PARAMS field. The code that encodes a value into that field
sets it unconditionally, which is wrong.
We currently only provide 0 as the field's value, so this error has
no real effect. Still, it's a bug, so let's fix it.
Fix an (unrelated) incorrect comment as well. Fields in the
ERROR_LOG GSI register actually *are* defined for IPA versions
prior to v3.5.1.
Fixes: fe68c43ce388 ("net: ipa: support enhanced channel flow control")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move include/linux/qcom_scm.h to include/linux/firmware/qcom/qcom_scm.h.
This removes 1 of a few remaining Qualcomm-specific headers into a more
approciate subdirectory under include/.
Suggested-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Elliot Berman <quic_eberman@quicinc.com>
Reviewed-by: Guru Das Srinagesh <quic_gurus@quicinc.com>
Acked-by: Mukesh Ojha <quic_mojha@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230203210956.3580811-1-quic_eberman@quicinc.com
|
|
IPA v5.0 uses two memory regions not previously used. Define them
and treat them as valid only for IPA v5.0.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The AP has third pulse generator available starting with IPA v5.0.
Redefine ipa_qtime_val() to support that possibility. Pass the IPA
pointer as an argument so the version can be determined. And stop
using the sign of the returned tick count to indicate which of two
pulse generators to use.
Instead, have the caller provide the address of a variable that will
hold the selected pulse generator for the Qtime value. And for
version 5.0, check whether the third pulse generator best represents
the time period.
Add code in ipa_qtime_config() to configure the fourth pulse
generator for IPA v5.0+; in that case configure both the third and
fourth pulse generators to use 10 msec granularity.
Consistently use "ticks" for local variables that represent a tick
count.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Starting with IPA v5.0, the head-of-line blocking timer has more
than two pulse generators available to define timer granularity.
To prepare for that, change the way the field value is encoded
to use ipa_reg_encode() rather than ipa_reg_bit().
The aggregation granularity selection could (in principle) also use
an additional pulse generator starting with IPA v5.0. Encode the
AGGR_GRAN_SEL field differently to allow that as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IPA v5.0+ separates the configuration of entries in the cached
(previously "hashed") routing and filtering tables into distinct
registers. Previously a single "filter and router" register updated
entries in both tables at once; now the routing and filter table
caches have separate registers that define their content.
This patch updates the code that zeroes entries in the cached filter
and router tables to support IPA versions including v5.0+.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the code that causes filter and router table caches to be
flushed so that it supports IPA versions 5.0+. It adds a comment in
ipa_hardware_config_hashing() that explains that cacheing does not
need to be enabled, just as before, because it's enabled by default.
(For the record, the FILT_ROUT_CACHE_CFG register would have been
used if we wanted to explicitly enable these.)
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Define some new registers that appear starting with IPA v5.0, along
with enumerated types identifying their fields. Code that uses
these will be added by upcoming patches.
Most of the new registers are related to filter and routing tables,
and in particular, their "hashed" variant. These tables are better
described as "cached", where a hash value determines which entries
are cached. From now on, naming related to this functionality will
use "cache" instead of "hash", and that is reflected in these new
register names. Some registers for managing these caches and their
contents have changed as well.
A few other new field definitions for registers (unrelated to table
caches) are also defined.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The IP_PACKET_INIT immediate command defines the destination
endpoint to which a packet should be sent. Prior to IPA v5.0, a
5 bit field in that command represents the endpoint, but starting
with IPA v5.0, the field is extended to 8 bits to support more than
32 endpoints.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Increase the number of endpoints supported by the driver to 36,
which IPA v5.0 supports. This makes it impossible to check at build
time whether the supported number is too big to fit within the
(5-bit) PACKET_INIT destination endpoint field. Instead, convert
the build time check to compare against what fits in 8 bits.
Add a check in ipa_endpoint_config() to also ensure the hardware
reports an endpoint count that's in the expected range. Just
open-code 32 as the limit (the PACKET_INIT field mask is not
available where we'd want to use it).
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace the enable_irq_wake() call with one to dev_pm_set_wake_irq()
instead. This will let the dev PM framework automatically manage the
the wakeup capability of the ipa IRQ and ensure that userspace requests
to enable/disable wakeup for the IPA via sysfs are respected.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20230127202758.2913612-1-caleb.connolly@linaro.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Update ipa_status_extract() to support IPA v5.0 and beyond. Because
the format of the IPA packet status depends on the version, pass an
IPA pointer to the function.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stop assuming the IPA packet status has a fixed format (defined by
a C structure). Instead, use a function to extract each field from
a block of data interpreted as an IPA packet status. Define an
enumerated type that identifies the fields that can be extracted.
The current function extracts fields based on the existing
ipa_status structure format (which is no longer used).
Define IPA_STATUS_RULE_MISS, to replace the calls to field_max() to
represent that condition; those depended on the knowing the width of
a filter or router rule in the IPA packet status structure.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The next patch reworks how the IPA packet status structure is
interpreted. This patch does some preparatory work, to make it
easier to see the effect of that change:
- Change a few functions that access fields in a IPA packet status
structure to store field values in local variables with names
related to the field.
- Pass a void pointer rather than an (equivalent) status pointer
to two functions called by ipa_endpoint_status_parse().
- Use "rule" rather than "val" as the name of a variable that
holds a routing rule ID.
- Consistently use "IPA packet status" rather than "status
element" when referring to this data structure.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Define the remaining values for opcode and exception fields in the
IPA packet status structure. Most of these values are powers-of-2,
suggesting they are meant to be used as bitmasks, but that is not
the case. Add comments to be clear about this, and express the
values in decimal format.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename the ipa_nat_en enumerated type to be ipa_nat_type, and rename
its symbols accordingly. Add a comment indicating those values are
also used in the IPA status nat_type field.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a 16 bit status mask defined in the IPA packet status
structure, of which only one (TAG_VALID) is currently used.
Define all other IPA status mask values in an enumerated type whose
numeric values are bit mask values (in CPU byte order) in the status
mask. Use the TAG_VALID value from that type rather than defining a
separate field mask.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IPA packet status structure changes in IPA v5.0 in ways that are
difficult to represent cleanly. As a small step toward redefining
it as a parsed block of data, use a constant to define its size,
rather than the size of the IPA status structure type.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
