| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add support for scanning PHY in PHY package nodes. PHY packages nodes
are just container for actual PHY on the MDIO bus.
Their PHY address defined in the PHY package node are absolute and
reflect the address on the MDIO bus.
mdio_bus.c and of_mdio.c is updated to now support and parse also
PHY package subnode by checking if the node name match
"ethernet-phy-package".
As PHY package reg is mandatory and each PHY in the PHY package must
have a reg, every invalid PHY Package node is ignored and will be
skipped by the autoscan fallback.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IPQ4019 MDIO internally divide the clock feed by AHB based on the
MDIO_MODE reg. On reset or power up, the default value for the
divider is 0xff that reflect the divider set to /256.
This makes the MDC run at a very low rate, that is, considering AHB is
always fixed to 100Mhz, a value of 390KHz.
This hasn't have been a problem as MDIO wasn't used for time sensitive
operation, it is now that on IPQ807x is usually mounted with PHY that
requires MDIO to load their firmware (example Aquantia PHY).
To handle this problem and permit to set the correct designed MDC
frequency for the SoC add support for the standard "clock-frequency"
property for the MDIO node.
The divider supports value from /1 to /256 and the common value are to
set it to /16 to reflect 6.25Mhz or to /8 on newer platform to reflect
12.5Mhz.
To scan if the requested rate is supported by the divider, loop with
each supported divider and stop when the requested rate match the final
rate with the current divider. An error is returned if the rate doesn't
match any value.
On MDIO reset, the divider is restored to the requested value to prevent
any kind of downclocking caused by the divider reverting to a default
value.
To follow 802.3 spec of 2.5MHz of default value, if divider is set at
/256 and "clock-frequency" is not set in DT, assume nobody set the
divider and try to find the closest MDC rate to 2.5MHz. (in the case of
AHB set to 100MHz, it's 1.5625MHz)
While at is also document other bits of the MDIO_MODE reg to have a
clear idea of what is actually applied there.
Documentation of some BITs is skipped as they are marked as reserved and
their usage is not clear (RES 11:9 GENPHY 16:13 RES1 19:17)
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of open coding, use IS_ALIGNED() and ALIGN_DOWN() when dealing
with alignment. Replace also literals with SZ_4K.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Link: https://lore.kernel.org/r/20231229145232.6163-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit cff9c565e65f3622e8dc1dcc21c1520a083dff35.
Revert based on feedback from Russell.
Link: https://lore.kernel.org/all/ZZPtUIRerqTI2%2Fyh@shell.armlinux.org.uk/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The __of_mdiobus_register() function was storing the device node in
dev.of_node without increasing its reference count. It implicitly relied
on the caller to maintain the allocated node until the mdiobus was
unregistered.
Now, __of_mdiobus_register() will acquire the node before assigning it,
and of_mdiobus_unregister_callback() will be called at the end of
mdio_unregister().
Drivers can now release the node immediately after MDIO registration.
Some of them are already doing that even before this patch.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the mii_bus API conversion to a split read() / read_c45(), there
might be MDIO parent buses which only populate the read_c45() and
write_c45() function pointers but not the C22 variants.
We haven't seen these in the wild paired with MDIO multiplexers, but
Andrew points out we should treat the corner case.
Link: https://lore.kernel.org/netdev/4ccd7dc9-b611-48aa-865f-68d3a1327ce8@lunn.ch/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20231213152712.320842-3-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Showing the precise error symbols can help debugging probe issues, such
as the recent -EIO error in of_mdiobus_register() caused by the lack of
bus->read_c45() and bus->write_c45() methods.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20231213152712.320842-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simplify the code by using read_poll_timeout().
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20231213222744.2891184-3-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With a clock interval of 400 nsec and a 64 bit transactions (32 bit
preamble & 16 bit control & 16 bit data), it is reasonable to assume
the mdio transaction will take 25.6 usec. Add a 30 usec delay before
the first poll to reduce the chance of a 1000-2000 usec sleep.
Reduce the timeout from 1000ms to 100ms as it is unlikely for the bus
to take this long.
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20231213222744.2891184-2-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
We expect new_bus->id to be NUL-terminated but not NUL-padded based on
its prior assignment through snprintf:
| snprintf(new_bus->id, MII_BUS_ID_SIZE, "gpio-%x", bus_id);
Due to this, a suitable replacement is `strscpy` [2] due to the fact
that it guarantees NUL-termination on the destination buffer without
unnecessarily NUL-padding.
We can also use sizeof() instead of a length macro as this more closely
ties the maximum buffer size to the destination buffer. Do this for two
instances.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20231211-strncpy-drivers-net-mdio-mdio-gpio-c-v3-1-76dea53a1a52@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if a module is built without a
MODULE_DESCRIPTION(). Fill them in based on the Kconfig text, or
similar.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20231028184458.99448-3-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit a243ecc323b9 ("net: mdio: xgene: Use device_get_match_data()")
dropped the unconditional use of xgene_mdio_of_match resulting in this
warning:
drivers/net/mdio/mdio-xgene.c:303:34: warning: unused variable 'xgene_mdio_of_match' [-Wunused-const-variable]
The fix is to drop of_match_ptr() which is not necessary because DT is
always used for this driver (well, it could in theory support ACPI only,
but CONFIG_OF is always enabled for arm64).
Fixes: a243ecc323b9 ("net: mdio: xgene: Use device_get_match_data()")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310170832.xnVXw1bb-lkp@intel.com/
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231019182345.833136-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
net/mac80211/key.c
02e0e426a2fb ("wifi: mac80211: fix error path key leak")
2a8b665e6bcc ("wifi: mac80211: remove key_mtx")
7d6904bf26b9 ("Merge wireless into wireless-next")
https://lore.kernel.org/all/20231012113648.46eea5ec@canb.auug.org.au/
Adjacent changes:
drivers/net/ethernet/ti/Kconfig
a602ee3176a8 ("net: ethernet: ti: Fix mixed module-builtin object")
98bdeae9502b ("net: cpmac: remove driver to prepare for platform removal")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mii_bus API conversion to read_c45() and write_c45() did not cover
the mdio-mux driver before read() and write() were made C22-only.
This broke arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-13bb.dtso.
The -EOPNOTSUPP from mdiobus_c45_read() is transformed by
get_phy_c45_devs_in_pkg() into -EIO, is further propagated to
of_mdiobus_register() and this makes the mdio-mux driver fail to probe
the entire child buses, not just the PHYs that cause access errors.
Fix the regression by introducing special c45 read and write accessors
to mdio-mux which forward the operation to the parent MDIO bus.
Fixes: db1a63aed89c ("net: phy: Remove fallback to old C45 method")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20231017143144.3212657-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use preferred device_get_match_data() instead of of_match_device() and
acpi_match_device() to get the driver match data. With this, adjust the
includes to explicitly include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
include/net/inet_sock.h
f866fbc842de ("ipv4: fix data-races around inet->inet_id")
c274af224269 ("inet: introduce inet->inet_flags")
https://lore.kernel.org/all/679ddff6-db6e-4ff6-b177-574e90d0103d@tessares.net/
Adjacent changes:
drivers/net/bonding/bond_alb.c
e74216b8def3 ("bonding: fix macvlan over alb bond support")
f11e5bd159b0 ("bonding: support balance-alb with openvswitch")
drivers/net/ethernet/broadcom/bgmac.c
d6499f0b7c7c ("net: bgmac: Return PTR_ERR() for fixed_phy_register()")
23a14488ea58 ("net: bgmac: Fix return value check for fixed_phy_register()")
drivers/net/ethernet/broadcom/genet/bcmmii.c
32bbe64a1386 ("net: bcmgenet: Fix return value check for fixed_phy_register()")
acf50d1adbf4 ("net: bcmgenet: Return PTR_ERR() for fixed_phy_register()")
net/sctp/socket.c
f866fbc842de ("ipv4: fix data-races around inet->inet_id")
b09bde5c3554 ("inet: move inet->mc_loop to inet->inet_frags")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
xgene_mdio_status is declared static, and is only written once by the
driver. It appears to have been this way since the driver was first
added to the kernel tree. No other users can be found, so let's remove
it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on the original code semantic in case of Clause 45 MDIO, the address
command is supposed to be followed by the command sending the MMD address,
not the CSR address. The commit 002dd3de097c ("net: mdio: mdio-bitbang:
Separate C22 and C45 transactions") has erroneously broken that. So most
likely due to an unfortunate variable name it switched the code to sending
the CSR address. In our case it caused the protocol malfunction so the
read operation always failed with the turnaround bit always been driven to
one by PHY instead of zero. Fix that by getting back the correct
behaviour: sending MMD address command right after the regular address
command.
Fixes: 002dd3de097c ("net: mdio: mdio-bitbang: Separate C22 and C45 transactions")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When building with clang 18 I see the following warning:
| drivers/net/mdio/mdio-xgene.c:338:13: warning: cast to smaller integer
| type 'enum xgene_mdio_id' from 'const void *' [-Wvoid-pointer-to-enum-cast]
| 338 | mdio_id = (enum xgene_mdio_id)of_id->data;
This is due to the fact that `of_id->data` is a void* while `enum
xgene_mdio_id` has the size of an int. This leads to truncation and
possible data loss.
Link: https://github.com/ClangBuiltLinux/linux/issues/1910
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20230815-void-drivers-net-mdio-mdio-xgene-v1-1-5304342e0659@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No need cast (void*) to (struct xgene_mdio_pdata *).
Signed-off-by: Wu Yunchuan <yunchuan@nfschina.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230717031212.54991-1-yunchuan@nfschina.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add mdio compat string for ASP 2.0 ethernet driver.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the recently added of_property_read_reg() helper to get the
untranslated "reg" address value.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There exists several examples today of devices that embed an ethernet
PHY or PCS directly inside an SoC. In this situation, either the device
is controlled through a vendor-specific register set, or sometimes
exposes the standard 802.3 registers that are typically accessed over
MDIO.
As phylib and phylink are designed to use mdiodevices, this driver
allows creating a virtual MDIO bus, that translates mdiodev register
accesses to regmap accesses.
The reason we use regmap is because there are at least 3 such devices
known today, 2 of them are Altera TSE PCS's, memory-mapped, exposed
with a 4-byte stride in stmmac's dwmac-socfpga variant, and a 2-byte
stride in altera-tse. The other one (nxp,sja1110-base-tx-mdio) is
exposed over SPI.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 87e3bee0f247 ("net: mdio: i2c: Separate C22 and C45 transactions")
separated the non-rollball bus accessors, but left the rollball
accessors as is. As rollball accessors are clause 45, this results
in the rollball protocol being completely non-functional. Fix this.
Fixes: 87e3bee0f247 ("net: mdio: i2c: Separate C22 and C45 transactions")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Should of_mdiobus_register() fail, a previous usb_get_dev() call should be
undone as in the .disconnect function.
Fixes: 04e37d92fbed ("net: phy: add marvell usb to mdio controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A number of MDIO drivers make use of devm_mdiobus_alloc_size(). This
is only available when CONFIG_MDIO_DEVRES is enabled. Add missing
depends or selects, depending on if there are circular dependencies or
not. This avoids linker errors, especially for randconfig builds.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230409150204.2346231-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
6e9d51b1a5cb ("net/mlx5e: Initialize link speed to zero")
1bffcea42926 ("net/mlx5e: Add devlink hairpin queues parameters")
https://lore.kernel.org/all/20230324120623.4ebbc66f@canb.auug.org.au/
https://lore.kernel.org/all/20230321211135.47711-1-saeed@kernel.org/
Adjacent changes:
drivers/net/phy/phy.c
323fe43cf9ae ("net: phy: Improved PHY error reporting in state machine")
4203d84032e2 ("net: phy: Ensure state transitions are processed from phy_stop()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In device_for_each_child_node(), we should add fwnode_handle_put()
when break out of the iteration device_for_each_child_node()
as it will automatically increase and decrease the refcounter.
Fixes: 379d7ac7ca31 ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bus ownership is wrong when using acpi_mdiobus_register() to register an
mdio bus. That function is not inline, so when it calls
mdiobus_register() the wrong THIS_MODULE value is captured.
CC: Maxime Bizon <mbizon@freebox.fr>
Fixes: 803ca24d2f92 ("net: mdio: Add ACPI support code for mdio")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bus ownership is wrong when using of_mdiobus_register() to register an mdio
bus. That function is not inline, so when it calls mdiobus_register() the wrong
THIS_MODULE value is captured.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Fixes: 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support from PHYs")
[florian: fix kdoc, added Fixes tag]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230310144716.1544083-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
