| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Realtek RTL8211F Ethernet PHY supports 3 LED pins which are used to
indicate link status and activity. Add minimal LED controller driver
supporting the most common uses with the 'netdev' trigger.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Realtek RTL8224 PHY is a 2.5Gbps capable PHY. It only uses the
clause 45 MDIO interface and can leverage the support that has already
been added for the other 822x PHYs.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20240611053415.2111723-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Sets ETHTOOL_LINK_MODE_TP_BIT in phydev->supported.
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The value of the register to determine the speed, is retrieved
differently when using Clause 45 only. To use the rtlgen_get_speed()
function in this case, pass the value of the register as argument to
rtlgen_get_speed(). The function would then always return 0, so change it
to void. A better name for this function now is rtlgen_decode_speed().
Replace a call to genphy_read_status() followed by rtlgen_get_speed()
with a call to rtlgen_read_status() in rtl822x_read_status().
Add reading speed to rtl822x_c45_read_status().
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Collected from several commits in [PATCH net-next]
"Realtek RTL822x PHY rework to c45 and SerDes interface switching"
The instances are used by Clause 45 only accessible PHY's on several sfp
modules, which are using RollBall protocol.
Signed-off-by: Marek Behún <kabel@kernel.org>
[ Added matching functions to differentiate C45 instances ]
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Uses vendor register to determine if SerDes is setup in rate-matching mode.
Rate-matching only supported when SerDes is set to 2500base-x.
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rtl8221b and rtl8226b series support switching SerDes mode between
2500base-x and sgmii based on the negotiated copper speed.
Configure this switching mode according to SerDes modes supported by
host.
There is an additional datasheet for RTL8226B/RTL8221B called
"SERDES MODE SETTING FLOW APPLICATION NOTE" where a sequence is
described to setup interface and rate adapter mode.
However, there is no documentation about the meaning of registers
and bits, it's literally just magic numbers and pseudo-code.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
[ refactored, dropped HiSGMII mode and changed commit message ]
Signed-off-by: Marek Behún <kabel@kernel.org>
[ changed rtl822x_update_interface() to use vendor register ]
[ always fill in possible interfaces ]
[ only apply to rtl8221b and rtl8226b phy's ]
[ set phydev->rate_matching in .config_init() ]
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: should come before them, without any blank lines. As the
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/ipv4/udp.c
f796feabb9f5 ("udp: add local "peek offset enabled" flag")
56667da7399e ("net: implement lockless setsockopt(SO_PEEK_OFF)")
Adjacent changes:
net/unix/garbage.c
aa82ac51d633 ("af_unix: Drop oob_skb ref before purging queue in GC.")
11498715f266 ("af_unix: Remove io_uring code for GC.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit bb726b753f75 ("net: phy: realtek: add support for
RTL8211F(D)(I)-VD-CG") extended support of the driver from the existing
support for RTL8211F(D)(I)-CG PHY to the newer RTL8211F(D)(I)-VD-CG PHY.
While that commit indicated that the RTL8211F_PHYCR2 register is not
supported by the "VD-CG" PHY model and therefore updated the corresponding
section in rtl8211f_config_init() to be invoked conditionally, the call to
"genphy_soft_reset()" was left as-is, when it should have also been invoked
conditionally. This is because the call to "genphy_soft_reset()" was first
introduced by the commit 0a4355c2b7f8 ("net: phy: realtek: add dt property
to disable CLKOUT clock") since the RTL8211F guide indicates that a PHY
reset should be issued after setting bits in the PHYCR2 register.
As the PHYCR2 register is not applicable to the "VD-CG" PHY model, fix the
rtl8211f_config_init() function by invoking "genphy_soft_reset()"
conditionally based on the presence of the "PHYCR2" register.
Fixes: bb726b753f75 ("net: phy: realtek: add support for RTL8211F(D)(I)-VD-CG")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240220070007.968762-1-s-vadapalli@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use generic MDIO helpers to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/422ae70f-7305-45fd-ab3e-0dd604b9fd6c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
RTL8126 as an evolution of RTL8125 supports 5Gbps. rtl822x_config_aneg()
is used by the PHY driver for the integrated PHY, therefore add 5Gbps
support to it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/5644ab50-e3e9-477c-96db-05cd5bdc2563@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the ad-hoc MDIO constants used in the driver and use generic
constants instead.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/732a70d6-4191-4aae-8862-3716b062aa9e@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A user reported that first consumer mainboards show up with a RTL8126A
5Gbps MAC/PHY. This adds support for the integrated PHY, which is also
available stand-alone. From a PHY driver perspective it's treated the
same as the 2.5Gbps PHY's, we just have to support the new PHY ID.
Reported-by: Joe Salmeri <jmscdba@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Joe Salmeri <jmscdba@gmail.com>
Link: https://lore.kernel.org/r/0c8e67ea-6505-43d1-bd51-94e7ecd6e222@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For PHYs that call rtl821x_probe() where an external clock can be
configured, make sure that the clock is disabled
when ->suspend() is called and enabled on resume.
The PHY_ALWAYS_CALL_SUSPEND is added to ensure that the suspend function
is actually always called.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some cases, the PHY can use an external clock source instead of a
crystal.
Add an optional clock in the phy node to make sure that the clock source
is enabled, if specified, before probing.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RTL8211F(D)(I)-VD-CG is the pin-to-pin upgrade chip from
RTL8211F(D)(I)-CG.
Add new PHY ID for this chip.
It does not support RTL8211F_PHYCR2 anymore, so remove the w/r operation
of this register.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RTL8365MB-VC ethernet switch controller has 4 internal PHYs for its
user-facing ports. All that is needed is to let the PHY driver core
pick up the IRQ made available by the switch driver.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The comparisons of the u16 values priv->phycr1 and priv->phycr2 to less
than zero always false because they are unsigned. Fix this by using an
int for the assignment and less than zero check.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: 0a4355c2b7f8 ("net: phy: realtek: add dt property to disable CLKOUT clock")
Fixes: d90db36a9e74 ("net: phy: realtek: add dt property to enable ALDPS mode")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHY will delay about 11.5ms to generate RXC clock when switching from
power down to normal operation. Read/write registers would also cause RXC
become unstable and stop for a while during this process. Realtek engineer
suggests 15ms or more delay can workaround this issue.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If enable Advance Link Down Power Saving (ALDPS) mode, it will change
crystal/clock behavior, which cause RXC clock stop for dozens to hundreds
of miliseconds. This is comfirmed by Realtek engineer. For some MACs, it
needs RXC clock to support RX logic, after this patch, PHY can generate
continuous RXC clock during auto-negotiation.
ALDPS default is disabled after hardware reset, it's more reasonable to
add a property to enable this feature, since ALDPS would introduce side effect.
This patch adds dt property "realtek,aldps-enable" to enable ALDPS mode
per users' requirement.
Jisheng Zhang enables this feature, changes the default behavior. Since
mine patch breaks the rule that new implementation should not break
existing design, so Cc'ed let him know to see if it can be accepted.
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CLKOUT is enabled by default after PHY hardware reset, this patch adds
"realtek,clkout-disable" property for user to disable CLKOUT clock
to save PHY power.
Per RTL8211F guide, a PHY reset should be issued after setting these
bits in PHYCR2 register. After this patch, CLKOUT clock output to be
disabled.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RTL9000AA/AN as 100BASE-T1 is following:
- 100 Mbps
- Full duplex
- Link Status Change Interrupt
- Master/Slave configuration
Signed-off-by: Yuusuke Ashizuka <ashiduka@fujitsu.com>
Signed-off-by: Torii Kenichi <torii.ken1@fujitsu.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210121080254.21286-1-ashiduka@fujitsu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The rtl8211f supports downshift and before commit 5502b218e001
("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")
the read-back of register MII_CTRL1000 was used to detect the
negotiated link speed.
The code added in commit d445dff2df60 ("net: phy: realtek: read
actual speed to detect downshift") is working fine also for this
phy and it's trivial re-using it to restore the downshift
detection on rtl8211f.
Add the phy specific read_status() pointing to the existing
function rtlgen_read_status().
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Link: https://lore.kernel.org/r/478f871a-583d-01f1-9cc5-2eea56d8c2a7@huawei.com
Tested-by: Yonglong Liu <liuyonglong@huawei.com>
Link: https://lore.kernel.org/r/20201124230756.887925-1-antonio.borneo@st.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The RTL8401-internal PHY identifies as RTL8201CP, and the init
sequence in r8169, copied from vendor driver r8168, uses paged
operations. Therefore set the same paged operation callbacks as
for the other Realtek PHY's.
Fixes: cdafdc29ef75 ("r8169: sync support for RTL8401 with vendor driver")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/69882f7a-ca2f-e0c7-ae83-c9b6937282cd@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Willy Liu <willy.liu@realtek.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Willy Liu <willy.liu@realtek.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Realtek single-port 2.5Gbps Ethernet PHYs are list as below:
RTL8226-CG: the 1st generation 2.5Gbps single port PHY
RTL8226B-CG/RTL8221B-CG: the 2nd generation 2.5Gbps single port PHY
RTL8221B-VB-CG: the 3rd generation 2.5Gbps single port PHY
RTL8221B-VM-CG: the 2.5Gbps single port PHY with MACsec feature
This patch adds the minimal drivers to manage these transceivers.
Signed-off-by: Willy Liu <willy.liu@realtek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1604281927-9874-1-git-send-email-willy.liu@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Realtek single-chip Ethernet PHY solutions can be separated as below:
10M/100Mbps: RTL8201X
1Gbps: RTL8211X
2.5Gbps: RTL8226/RTL8221X
RTL8226 is the first version for realtek that compatible 2.5Gbps single PHY.
Since RTL8226 is single port only, realtek changes its name to RTL8221B from
the second version.
PHY ID for RTL8226 is 0x001cc800 and RTL8226B/RTL8221B is 0x001cc840.
RTL8125 is not a single PHY solution, it integrates PHY/MAC/PCIE bus
controller and embedded memory.
Signed-off-by: Willy Liu <willy.liu@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two chip pins named TXDLY and RXDLY which actually adds the 2ns
delays to TXC and RXC for TXD/RXD latching. These two pins can config via
4.7k-ohm resistor to 3.3V hw setting, but also config via software setting
(extension page 0xa4 register 0x1c bit13 12 and 11).
The configuration register definitions from table 13 official PHY datasheet:
PHYAD[2:0] = PHY Address
AN[1:0] = Auto-Negotiation
Mode = Interface Mode Select
RX Delay = RX Delay
TX Delay = TX Delay
SELRGV = RGMII/GMII Selection
This table describes how to config these hw pins via external pull-high or pull-
low resistor.
It is a misunderstanding that mapping it as register bits below:
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Interface Mode Select
2 = RX Delay
1 = TX Delay
0 = SELRGV
So I removed these descriptions above and add related settings as below:
14 = reserved
13 = force Tx RX Delay controlled by bit12 bit11
12 = Tx Delay
11 = Rx Delay
10:0 = Test && debug settings reserved by realtek
Test && debug settings are not recommend to modify by default.
Fixes: f81dadbcf7fd ("net: phy: realtek: Add rtl8211e rx/tx delays config")
Signed-off-by: Willy Liu <willy.liu@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable ALDPS(Advanced Link Down Power Saving) to save power when
link down.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Realtek assigned a new PHY ID for the RTL8125B-internal PHY.
It's however compatible with the RTL8125A-internal PHY.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Internal PHY's from RTL8168h up may not be instantly ready after calling
genphy_resume(). So far r8169 network driver adds the needed delay, but
better handle this in the PHY driver. The network driver may miss other
places where the PHY is resumed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At least some integrated PHY's in RTL8168/RTL8125 chip versions support
downshift, and the actual link speed can be read from a vendor-specific
register. Info about this register was provided by Realtek.
More details about downshift configuration (e.g. number of attempts)
aren't available, therefore the downshift tunable is not implemented.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On RTL8211F the RX and TX delays (2ns) can be configured in two ways:
- pin strapping (RXD1 for the TX delay and RXD0 for the RX delay, LOW
means "off" and HIGH means "on") which is read during PHY reset
- using software to configure the TX and RX delay registers
So far only the configuration using pin strapping has been supported.
Add support for enabling or disabling the RGMII RX delay based on the
phy-mode to be able to get the RX delay into a known state. This is
important because the RX delay has to be coordinated between the PHY,
MAC and the PCB design (trace length). With an invalid RX delay applied
(for example if both PHY and MAC add a 2ns RX delay) Ethernet may not
work at all.
Also add debug logging when configuring the RX delay (just like the TX
delay) because this is a common source of problems.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RGMII requires a delay of 2ns between the data and the clock signal.
There are at least three ways this can happen. One possibility is by
having the PHY generate this delay.
This is a common source for problems (for example with slow TX speeds or
packet loss when sending data). The TX delay configuration of the
RTL8211F PHY can be set either by pin-strappping the RXD1 pin (HIGH
means enabled, LOW means disabled) or through configuring a paged
register. The setting from the RXD1 pin is also reflected in the
register.
Add debug logging to the TX delay configuration on RTL8211F so it's
easier to spot these issues (for example if the TX delay is enabled for
both, the RTL8211F PHY and the MAC).
This is especially helpful because there is no public datasheet for the
RTL8211F PHY available with all the RX/TX delay specifics.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was reported [0] that since the referenced commit a warning is
triggered in phylib that complains about paged operations being used
with a PHY driver that doesn't support this. The commit isn't wrong,
just for one chip version (RTL8105e) no dedicated PHY driver exists
yet. So add the missing PHY driver.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202103
Fixes: 3a129e3f9ac4 ("r8169: switch to phylib functions in more places")
Reported-by: jhdskag3 <jhdskag3@tutanota.com>
Tested-by: jhdskag3 <jhdskag3@tutanota.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Emulate the 802.3bz MMD EEE registers for 2.5Gbps EEE on RTL8125.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
EEE-related registers on newer integrated PHY's have the standard
layout, but are accessible not via MMD but via vendor-specific
registers. Emulating the standard MMD registers allows to use the
generic functions for EEE control.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Realtek provided information on how the new NIC-integrated PHY's
expose whether they support 2.5G/5G/10G. This allows to automatically
differentiate 1Gbps and 2.5Gbps PHY's, and therefore allows to
remove the fake PHY ID mechanism for RTL8125.
So far RTL8125 supports 2.5Gbps only, but register layout for faster
modes has been defined already, so let's use this information to be
future-proof.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for the integrated 2.5Gbps PHY in Realtek RTL8125.
Advertisement of 2.5Gbps mode is done via a vendor-specific register.
Same applies to reading NBase-T link partner advertisement.
Unfortunately this 2.5Gbps PHY shares the PHY ID with the integrated
1Gbps PHY's in other Realtek network chips and so far no method is
known to differentiate them. As a workaround use a dedicated fake PHY ID
that is set by the network driver by intercepting the MDIO PHY ID read.
v2:
- Create dedicated PHY driver and use a fake PHY ID that is injected by
the network driver. Suggested by Andrew Lunn.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rtl8211e_config_init()
After calling phy_select_page() and until calling phy_restore_page(),
the mutex 'mdio_lock' is already locked, so the driver should use
non-locked version of phy functions. Or there will be a deadlock with
'mdio_lock'.
This replaces phy functions called from rtl8211e_config_init() to avoid
the deadlock issue.
Fixes: f81dadbcf7fd ("net: phy: realtek: Add rtl8211e rx/tx delays config")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When adding missing callbacks I missed that one had them set already.
Interesting that the compiler didn't complain.
Fixes: daf3ddbe11a2 ("net: phy: realtek: add missing page operations")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing page operation callbacks to few Realtek drivers.
This also fixes a NPE after the referenced commit added code to the
RTL8211E driver that uses phy_select_page().
Fixes: f81dadbcf7fd ("net: phy: realtek: Add rtl8211e rx/tx delays config")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reported-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's prone to problems if delay is cleared out for other than RGMII
modes. So lets set/clear the TX-delay in the config register only
if actually RGMII-like interface mode is requested. This only
concerns rtl8211f chips.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two chip pins named TXDLY and RXDLY which actually adds the 2ns
delays to TXC and RXC for TXD/RXD latching. Alas this is the only
documented info regarding the RGMII timing control configurations the PHY
provides. It turns out the same settings can be setup via MDIO registers
hidden in the extension pages layout. Particularly the extension page 0xa4
provides a register 0x1c, which bits 1 and 2 control the described delays.
They are used to implement the "rgmii-{id,rxid,txid}" phy-mode.
The hidden RGMII configs register utilization was found in the rtl8211e
U-boot driver:
https://elixir.bootlin.com/u-boot/v2019.01/source/drivers/net/phy/realtek.c#L99
There is also a freebsd-folks discussion regarding this register:
https://reviews.freebsd.org/D13591
It confirms that the register bits field must control the so called
configuration pins described in the table 12-13 of the official PHY
datasheet:
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Interface Mode Select
2 = RX Delay
1 = TX Delay
0 = SELRGV
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that phylib uses genphy_read_abilities() as fallback, we don't have
to set callback get_features any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use new function genphy_read_abilities(). This allows to remove all
calls to genphy_config_init().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
