Age | Commit message (Collapse) | Author | Files | Lines |
|
ath.git patches for v5.19. Major changes:
ath11k
* enable keepalive during WoWLAN suspend
* implement remain-on-channel support
|
|
This patch adds the new struct ieee80211_rate_status and replaces
'struct rate_info *rate' in ieee80211_tx_status with pointer and length
annotation.
The struct ieee80211_rate_status allows to:
(1) receive tx power status feedback for transmit power control (TPC)
per packet or packet retry
(2) dynamic mapping of wifi chip specific multi-rate retry (mrr)
chains with different lengths
(3) increase the limit of annotatable rate indices to support
IEEE802.11ac rate sets and beyond
ieee80211_tx_info, control and status buffer, and ieee80211_tx_rate
cannot be used to achieve these goals due to fixed size limitations.
Our new struct contains a struct rate_info to annotate the rate that was
used, retry count of the rate and tx power. It is intended for all
information related to RC and TPC that needs to be passed from driver to
mac80211 and its RC/TPC algorithms like Minstrel_HT. It corresponds to
one stage in an mrr. Multiple subsequent instances of this struct can be
included in struct ieee80211_tx_status via a pointer and a length variable.
Those instances can be allocated on-stack. The former reference to a single
instance of struct rate_info is replaced with our new annotation.
An extension is introduced to struct ieee80211_hw. There are two new
members called 'tx_power_levels' and 'max_txpwr_levels_idx' acting as a
tx power level table. When a wifi device is registered, the driver shall
supply all supported power levels in this list. This allows to support
several quirks like differing power steps in power level ranges or
alike. TPC can use this for algorithm and thus be designed more abstract
instead of handling all possible step widths individually.
Further mandatory changes in status.c, mt76 and ath11k drivers due to the
removal of 'struct rate_info *rate' are also included.
status.c already uses the information in ieee80211_tx_status->rate in
radiotap, this is now changed to use ieee80211_rate_status->rate_idx.
mt76 driver already uses struct rate_info to pass the tx rate to status
path. The new members of the ieee80211_tx_status are set to NULL and 0
because the previously passed rate is not relevant to rate control and
accurate information is passed via tx_info->status.rates.
For ath11k, the txrate can be passed via this struct because ath11k uses
firmware RC and thus the information does not interfere with software RC.
Compile-Tested: current wireless-next tree with all flags on
Tested-on: Xiaomi 4A Gigabit (MediaTek MT7603E, MT7612E) with OpenWrt
Linux 5.10.113
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://lore.kernel.org/r/20220509173958.1398201-2-jelonek.jonas@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The variables vht_mcs and he_mcs are being initialized in the
start of for-loops however they are re-assigned new values in
the loop and not used outside the loop. The initializations
are redundant and can be removed.
Cleans up clang scan warnings:
warning: Although the value stored to 'vht_mcs' is used in the
enclosing expression, the value is never actually read from
'vht_mcs' [deadcode.DeadStores]
warning: Although the value stored to 'he_mcs' is used in the
enclosing expression, the value is never actually read from
'he_mcs' [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220507184155.26939-1-colin.i.king@gmail.com
|
|
Ath11k allocates memory when firmware requests memory in QMI.
Coldboot calibration and firmware recovery uses firmware reload.
On firmware reload, firmware sends memory request again. If Ath11k
allocates memory on first firmware boot, reuse the available
memory. Also check if the segment type and size is same
on the next firmware boot. Reuse if segment type/size is
same as previous firmware boot else free the segment and
allocate the segment with size/type.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.6.0.1-00752-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <quic_akolli@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506141448.10340-1-quic_akolli@quicinc.com
|
|
In case of Passpoint, the WLAN interface may be requested to
remain on a specific channel and then to send some management
frames on that channel. Now chanfreq of wmi_mgmt_send_cmd is set
as 0, as a result firmware may choose a default but wrong channel.
Fix it by assigning chanfreq field with the designated channel.
This change only applies to WCN6855 and QCA6390, other chips are
not affected.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506013614.1580274-4-quic_bqiang@quicinc.com
|
|
Commit 66307ca04057 ("ath11k: fix mgmt_tx_wmi cmd sent to FW for
deleted vdev") wants both of below two conditions are true before
sending management frames:
1: ar->allocated_vdev_map & (1LL << arvif->vdev_id)
2: arvif->is_started
Actually the second one is not necessary because with the first one
we can make sure the vdev is present.
Also use ar->conf_mutex to synchronize vdev delete and mgmt. TX.
This issue is found in case of Passpoint scenario where ath11k
needs to send action frames before vdev is started.
Fix it by removing the second condition.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Fixes: 66307ca04057 ("ath11k: fix mgmt_tx_wmi cmd sent to FW for deleted vdev")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506013614.1580274-3-quic_bqiang@quicinc.com
|
|
Add remain on channel support, it is needed in several
scenarios such as Passpoint etc.
Currently this is supported by QCA6390, WCN6855, IPQ8074,
IPQ6018 and QCN9074.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506013614.1580274-2-quic_bqiang@quicinc.com
|
|
With WoWLAN enabled and after sleeping for a rather long time,
we are seeing that with some APs, it is not able to wake up
the STA though the correct wake up pattern has been configured.
This is because the host doesn't send keepalive command to
firmware, thus firmware will not send any packet to the AP and
after a specific time the AP kicks out the STA.
Fix this issue by enabling keepalive before going to suspend
and disabling it after resume back.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506012540.1579604-1-quic_bqiang@quicinc.com
|
|
When doing simulate_fw_crash operation periodically with a short interval
time such as 10 seconds, it is easy happened WMI command timed out for
WMI_SCAN_CHAN_LIST_CMDID in ath11k_reg_update_chan_list().
log:
[42287.610053] ath11k_pci 0000:01:00.0: wmi command 12291 timeout
[42287.610064] ath11k_pci 0000:01:00.0: failed to send WMI_SCAN_CHAN_LIST cmd
[42287.610073] ath11k_pci 0000:01:00.0: failed to perform regd update : -11
Note that this issue does not occur with a longer interval such as 20 seconds.
The reason the issue occurs with a shorter interval is the following steps:
1) Upon initial boot, or after device recovery, the initial hw scan plus
the 11d scan will run, and when 6 GHz support is present, these scans
can take up to 12 seconds to complete, so ath11k_reg_update_chan_list()
is still waiting the completion of ar->completed_11d_scan.
2) If a simulate_fw_crash operation is received during this time, those
scans do not complete, and ath11k_core_pre_reconfigure_recovery()
complete the ar->completed_11d_scan, then ath11k_reg_update_chan_list()
wakeup and start to send WMI_SCAN_CHAN_LIST_CMDID, but firmware is crashed
at this moment, so wmi timed out occur.
To address this issue, reset the 11d state during device recovery so that
WMI_SCAN_CHAN_LIST_CMDID does not timed out for short interval time such
as 10 seconds.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 1f682dc9fb37 ("ath11k: reduce the wait time of 11d scan and hw scan while add interface")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220505034636.29582-1-quic_wgong@quicinc.com
|
|
The offset of REO register where the RX fragment destination ring
is configured is different in WCN6750 as compared to WCN6855.
Due to this differnce in offsets, on WCN6750, fragment destination
ring will be configured incorrectly, leading to RX fragments not
getting delivered to the driver. Fix this by defining HW specific
offsets for the REO MISC CTL register.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220504083900.31513-1-quic_mpubbise@quicinc.com
|
|
checkpatch warns:
drivers/net/wireless/ath/ath11k/mac.c:7760: line length of 91 exceeds 90 columns
This was introduced by commit 046d2e7c50e3 ("mac80211: prepare sta handling for
MLO support").
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220503060415.24499-1-kvalo@kernel.org
|
|
Add the support to attach WCN6750 and map iommu domain
for targets which do not have the support of TrustZone.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328062032.28881-1-quic_mpubbise@quicinc.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v5.19
First set of patches for v5.19 and this is a big one. We have two new
drivers, a change in mac80211 STA API affecting most drivers and
ath11k getting support for WCN6750. And as usual lots of fixes and
cleanups all over.
Major changes:
new drivers
- wfx: silicon labs devices
- plfxlc: pureLiFi X, XL, XC devices
mac80211
- host based BSS color collision detection
- prepare sta handling for IEEE 802.11be Multi-Link Operation (MLO) support
rtw88
- support TP-Link T2E devices
rtw89
- support firmware crash simulation
- preparation for 8852ce hardware support
ath11k
- Wake-on-WLAN support for QCA6390 and WCN6855
- device recovery (firmware restart) support for QCA6390 and WCN6855
- support setting Specific Absorption Rate (SAR) for WCN6855
- read country code from SMBIOS for WCN6855/QCA6390
- support for WCN6750
wcn36xx
- support for transmit rate reporting to user space
* tag 'wireless-next-2022-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (228 commits)
rtw89: 8852c: rfk: add DPK
rtw89: 8852c: rfk: add IQK
rtw89: 8852c: rfk: add RX DCK
rtw89: 8852c: rfk: add RCK
rtw89: 8852c: rfk: add TSSI
rtw89: 8852c: rfk: add LCK
rtw89: 8852c: rfk: add DACK
rtw89: 8852c: rfk: add RFK tables
plfxlc: fix le16_to_cpu warning for beacon_interval
rtw88: remove a copy of the NAPI_POLL_WEIGHT define
carl9170: tx: fix an incorrect use of list iterator
wil6210: use NAPI_POLL_WEIGHT for napi budget
ath10k: remove a copy of the NAPI_POLL_WEIGHT define
ath11k: Add support for WCN6750 device
ath11k: Datapath changes to support WCN6750
ath11k: HAL changes to support WCN6750
ath11k: Add QMI changes for WCN6750
ath11k: Fetch device information via QMI for WCN6750
ath11k: Add register access logic for WCN6750
ath11k: Add HW params for WCN6750
...
====================
Link: https://lore.kernel.org/r/20220503153622.C1671C385A4@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ath.git patches for v5.19. Major changes:
ath11k
* support setting Specific Absorption Rate (SAR) for WCN6855
* read country code from SMBIOS for WCN6855/QCA6390
* support for WCN6750
|
|
WCN6750 is non-DBS 2x2 11AX chipset. Unlike QCA6390 which is a
DBS (dual band simultaneous) solution (2 LMACs), WCN6750 has a
single LMAC supporting 2G, 5G and 6G bands but will operate only
on one band at any given point.
WCN6750 is a PCIe based solution, but it is attached to the WPSS
(Wireless Processor SubSystem) Q6 processor, hence it is enumerated
by the Q6 processor. It is registered to the APSS processor
(Application Processor SubSystem) as a platform device(AHB) and
remoteproc APIs are used to boot up or shutdown the device like
other AHB devices.
Also, Device information like BAR and it's size is not known to the
APSS processor as the chip is enumerated by WPSS Q6. These details
are fetched over QMI.
STA and AP modes are supported. Verified basic connectivity and ping
in both the modes.
An important point to note is that though WCN6750 is a PCIe device,
it cannot be attached to any other platform except on Qualcomm
Snapdragon SoCs due to the aforementioned reasons.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-10-quic_mpubbise@quicinc.com
|
|
HAL RX descriptor for WCN6750 is same as QCN9074, this
means that the size of the HAL RX decriptor and the DP
APIs that WCN6750 requires to enable datapath should be
initialized with that of QCN9074's RX descriptor size
and the DP APIs respectively. There is one change wrt to
REO configuration though, REO configuration for WCN6750
follows WCN6855, therefore use reo_setup() of WCN6855
for WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-9-quic_mpubbise@quicinc.com
|
|
Add HAL changes required to support WCN6750. Offsets of some registers
for WCN6750 are different from other supported devices; move such
register offsets to platform specific ath11k_hw_regs.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-8-quic_mpubbise@quicinc.com
|
|
In the case of WCN6750, FW doesn't request for DDR memory
via QMI, instead it uses a fixed 12MB reserved Memory region
in the DDR which is called as MSA region. As a result, QMI
message sequence is not same as other ath11k supported devices.
Also, M3 firmware will be bundled into the FW and will be
downloaded to the target as part of Q6 boot.
This is the QMI flow in the case of WCN6750,
1) QMI firmware indication REQ/RESP
2) QMI host capability REQ/RESP
3) QMI target capability REQ/RESP
4) QMI device info REQ/RESP
5) QMI BDF download
6) QMI FW ready
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-7-quic_mpubbise@quicinc.com
|
|
Since WPPS Q6 does the PCIe enumeration of WCN6750, device
information like BAR and BAR size is not known to the APPS
processor (Application Processor SubSystem). In order to
fetch these details, a QMI message called device info request
will be sent to the target. Therefore, add logic to fetch
BAR details from the target.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-6-quic_mpubbise@quicinc.com
|
|
WCN6750 uses static window mapping to access the HW registers.
Unlike QCN9074 which uses 3rd window for UMAC and 2nd window
for CE register access, WCN6750 uses 1st window for UMAC
and 2nd window for CE registers.
Also, refactor the code so that WCN6750 can use the existing
ath11k_pci_read32/write32() APIs for accessing the registers.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-5-quic_mpubbise@quicinc.com
|
|
WCN6750 is a PCIe based solution that is attached to and enumerated
by the WPSS (Wireless Processor SubSystem) Q6 processor.
Though it is a PCIe device, since it is not attached to APSS processor
(Application Processor SubSystem), APSS will be unaware of such a decice
and hence it is registered to the APSS processor as a platform device(AHB).
Because of this hybrid nature, it is called as a hybrid bus device.
A new variable hybrid_bus_type is defined in hw_params to indicate the
hybrid nature of the device.
Add HW params for WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-4-quic_mpubbise@quicinc.com
|
|
In ath11k, bus_params were added with an intention to hold
parameters related to bus (AHB/PCI), but this is not true
as some bus parameters being different between chipsets of
the same bus.
With the addition of WCN6750 to ath11k, bus parameters are
going to be entirely different among AHB devices. Therefore,
it is wise to move bus_params to hw_params and get rid of
bus_params entirely.
Also, mhi_support parameter is not used anywhere in the driver,
remove it from bus_params.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-3-quic_mpubbise@quicinc.com
|
|
In the phase of wlan load, it has hw scan and 11d scan which sent to
firmware by ath11k, then hw scan and 11d scan will use about 14 seconds,
and meanwhile ath11k_reg_update_chan_list() is running in workqueue of
ath11k_base, and wait for 11d scan/hw scan finished. When the hw scan
finished, mac80211 will start to connect and send management packet,
at this moment, ath11k_reg_update_chan_list() is still waiting for 11d
scan finished, so wmi_mgmt_tx_work of ath11k will not run and thus the
tx management packet also not send out and lead authentication timed
out.
log:
INFO kernel: [ 187.885322] wlan0: authenticate with 72:6c:57:43:9f:90
INFO kernel: [ 187.937266] wlan0: send auth to 72:6c:57:43:9f:90 (try 1/3)
INFO kernel: [ 188.626944] wlan0: send auth to 72:6c:57:43:9f:90 (try 2/3)
INFO kernel: [ 189.650999] wlan0: send auth to 72:6c:57:43:9f:90 (try 3/3)
INFO kernel: [ 190.651917] wlan0: authentication with 72:6c:57:43:9f:90 timed out
Change wmi_mgmt_tx_work to another queue workqueue_aux of ath11k_base,
then connection success.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220428023320.4007-1-quic_wgong@quicinc.com
|
|
When test connect/disconnect to an AP frequently with WCN6855, sometimes
it show below log.
[ 277.040121] wls1: deauthenticating from 8c:21:0a:b3:5a:64 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 277.050906] ath11k_pci 0000:05:00.0: wmi stats vdev id 0 mac 00:03:7f:29:61:11
[ 277.050944] ath11k_pci 0000:05:00.0: wmi stats bssid 8c:21:0a:b3:5a:64 vif pK-error
[ 277.050954] ath11k_pci 0000:05:00.0: not found station for bssid 8c:21:0a:b3:5a:64
[ 277.050961] ath11k_pci 0000:05:00.0: failed to parse rssi chain -71
[ 277.050967] ath11k_pci 0000:05:00.0: failed to pull fw stats: -71
[ 277.050976] ath11k_pci 0000:05:00.0: wmi stats vdev id 0 mac 00:03:7f:29:61:11
[ 277.050983] ath11k_pci 0000:05:00.0: wmi stats bssid 8c:21:0a:b3:5a:64 vif pK-error
[ 277.050989] ath11k_pci 0000:05:00.0: not found station for bssid 8c:21:0a:b3:5a:64
[ 277.050995] ath11k_pci 0000:05:00.0: failed to parse rssi chain -71
[ 277.051000] ath11k_pci 0000:05:00.0: failed to pull fw stats: -71
[ 278.064050] ath11k_pci 0000:05:00.0: failed to request fw stats: -110
Reason is:
When running disconnect operation, sta_info removed from local->sta_hash
by __sta_info_destroy_part1() from __sta_info_flush(), after this,
ieee80211_find_sta_by_ifaddr() which called by
ath11k_wmi_tlv_fw_stats_data_parse() and ath11k_wmi_tlv_rssi_chain_parse()
cannot find this station, then failed log printed.
steps are like this:
1. when disconnect from AP, __sta_info_destroy() called __sta_info_destroy_part1()
and __sta_info_destroy_part2().
2. in __sta_info_destroy_part1(), it has "sta_info_hash_del(local, sta)"
and "list_del_rcu(&sta->list)", it will remove the ieee80211_sta from the
list of ieee80211_hw.
3. in __sta_info_destroy_part2(), it called drv_sta_state()->ath11k_mac_op_sta_state(),
then peer->sta is clear at this moment.
4. in __sta_info_destroy_part2(), it then called sta_set_sinfo()->drv_sta_statistics()
->ath11k_mac_op_sta_statistics(), then WMI_REQUEST_STATS_CMDID sent to firmware.
5. WMI_UPDATE_STATS_EVENTID reported from firmware, at this moment, the
ieee80211_sta can not be found again because it has remove from list in
step2 and also peer->sta is clear in step3.
6. in __sta_info_destroy_part2(), it then called cleanup_single_sta()->
sta_info_free()->kfree(sta), at this moment, the ieee80211_sta is freed
in memory, then the failed log will not happen because function
ath11k_mac_op_sta_state() will not be called.
Actually this print log is not a real error, it is only to skip parse the
info, so change to skip print by default debug setting.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220428022426.2927-1-quic_wgong@quicinc.com
|
|
We are seeing below warning:
...
kernel: [ 5720.362941] BUG: sleeping function called from invalid context at include/linux/sched/mm.h:197
kernel: [ 5720.362943] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 0, name: swapper/4
kernel: [ 5720.362947] CPU: 4 PID: 0 Comm: swapper/4 Tainted: G W 5.10.90 #18 4fa489e3e5c16043994f416310c2f60eff666320
kernel: [ 5720.362949] Hardware name: Google Nipperkin/Nipperkin, BIOS Google_Nipperkin.14316.0.0 10/30/2021
kernel: [ 5720.362950] Call Trace:
kernel: [ 5720.362953] <IRQ>
kernel: [ 5720.362959] dump_stack+0x9c/0xe7
kernel: [ 5720.362964] ___might_sleep+0x14a/0x160
kernel: [ 5720.362967] kmem_cache_alloc+0x46/0x226
kernel: [ 5720.362970] ? __alloc_skb+0x6c/0x19e
kernel: [ 5720.362972] __alloc_skb+0x6c/0x19e
kernel: [ 5720.362985] cfg80211_gtk_rekey_notify+0xa2/0x21d [cfg80211 2c8b5aee0416e7d010d70c332a47990fc843c1c5]
kernel: [ 5720.362995] ath11k_wmi_gtk_offload_status_event+0x102/0x155 [ath11k 4c6bb5f7331c81199d56a7e37bdc10030f167838]
kernel: [ 5720.363002] ath11k_wmi_tlv_op_rx+0x301/0x51b [ath11k 4c6bb5f7331c81199d56a7e37bdc10030f167838]
kernel: [ 5720.363009] ath11k_htc_rx_completion_handler+0xee/0x3f5 [ath11k 4c6bb5f7331c81199d56a7e37bdc10030f167838]
kernel: [ 5720.363017] ath11k_ce_per_engine_service+0x2aa/0x32c [ath11k 4c6bb5f7331c81199d56a7e37bdc10030f167838]
kernel: [ 5720.363024] ath11k_pci_ce_tasklet+0x1a/0x30 [ath11k_pci 9acc399855ea172aa14a892c0bfdba0ce22d6f07]
kernel: [ 5720.363028] tasklet_action_common+0x8d/0x9f
kernel: [ 5720.363032] __do_softirq+0x163/0x29a
kernel: [ 5720.363035] asm_call_irq_on_stack+0x12/0x20
kernel: [ 5720.363037] </IRQ>
kernel: [ 5720.363041] do_softirq_own_stack+0x3c/0x48
kernel: [ 5720.363043] __irq_exit_rcu+0x9b/0x9d
kernel: [ 5720.363046] common_interrupt+0xc9/0x14d
kernel: [ 5720.363049] asm_common_interrupt+0x1e/0x40
kernel: [ 5720.363054] RIP: 0010:cpuidle_enter_state+0x1c5/0x2ac
kernel: [ 5720.363056] Code: 84 f6 4c 8b 75 c0 74 1e 48 c7 45 c8 00 00 00 00 9c 8f 45 c8 0f ba 65 c8 09 0f 82 d1 00 00 00 31 ff e8 4a bb 6c ff fb 45 85 e4 <78> 47 44 89 e0 48 6b d0 68 49 8b 4c 16 48 48 2b 5d b8 49 89 5d 18
kernel: [ 5720.363058] RSP: 0018:ffffa7e640157e78 EFLAGS: 00000206
kernel: [ 5720.363060] RAX: ffff9807ddf29b40 RBX: 00000533e033584c RCX: 00000533e033584c
kernel: [ 5720.363062] RDX: 0000000000000004 RSI: 0000000000000000 RDI: 0000000000000000
kernel: [ 5720.363063] RBP: ffffa7e640157ec0 R08: 0000000000000002 R09: 00000533e171bb7a
kernel: [ 5720.363064] R10: 0000000000000900 R11: fffffffffffffffe R12: 0000000000000003
kernel: [ 5720.363065] R13: ffff9804c2ef6000 R14: ffffffffbe9a7bd0 R15: 0000000000000003
kernel: [ 5720.363069] ? cpuidle_enter_state+0x19a/0x2ac
kernel: [ 5720.363072] cpuidle_enter+0x2e/0x3d
kernel: [ 5720.363074] do_idle+0x163/0x1ee
kernel: [ 5720.363076] cpu_startup_entry+0x1d/0x1f
kernel: [ 5720.363078] secondary_startup_64_no_verify+0xb1/0xbb
...
This is because GFP_KERNEL is used by ath11k_wmi_gtk_offload_status_event
while in atomic context. Fix it by using GFP_ATOMIC instead.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: a16d9b50cfba ("ath11k: support GTK rekey offload")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220427120033.1046759-1-quic_bqiang@quicinc.com
|
|
This read the country code from SMBIOS and send the country code
to firmware, firmware will indicate the regulatory domain info of the
country code and then ath11k will use the info.
dmesg:
[ 1242.637173] ath11k_pci 0000:02:00.0: chip_id 0x2 chip_family 0xb board_id 0xff soc_id 0x400c0200
[ 1242.637176] ath11k_pci 0000:02:00.0: fw_version 0x110b09e5 fw_build_timestamp 2021-06-22 09:32 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HSP.1.1-02533-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
[ 1242.637253] ath11k_pci 0000:02:00.0: worldwide regdomain setting from SMBIOS
[ 1242.637259] ath11k_pci 0000:02:00.0: bdf variant name not found.
[ 1242.637261] ath11k_pci 0000:02:00.0: SMBIOS bdf variant name not set.
[ 1242.637263] ath11k_pci 0000:02:00.0: DT bdf variant name not set.
[ 1242.927543] ath11k_pci 0000:02:00.0: set current country pdev id 0 alpha2 00
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220421023501.32167-1-quic_wgong@quicinc.com
|
|
When ath11k modules are removed using rmmod with spectral scan enabled,
crash is observed. Different crash trace is observed for each crash.
Send spectral scan disable WMI command to firmware before cleaning
the spectral dbring in the spectral_deinit API to avoid this crash.
call trace from one of the crash observed:
[ 1252.880802] Unable to handle kernel NULL pointer dereference at virtual address 00000008
[ 1252.882722] pgd = 0f42e886
[ 1252.890955] [00000008] *pgd=00000000
[ 1252.893478] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[ 1253.093035] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.89 #0
[ 1253.115261] Hardware name: Generic DT based system
[ 1253.121149] PC is at ath11k_spectral_process_data+0x434/0x574 [ath11k]
[ 1253.125940] LR is at 0x88e31017
[ 1253.132448] pc : [<7f9387b8>] lr : [<88e31017>] psr: a0000193
[ 1253.135488] sp : 80d01bc8 ip : 00000001 fp : 970e0000
[ 1253.141737] r10: 88e31000 r9 : 970ec000 r8 : 00000080
[ 1253.146946] r7 : 94734040 r6 : a0000113 r5 : 00000057 r4 : 00000000
[ 1253.152159] r3 : e18cb694 r2 : 00000217 r1 : 1df1f000 r0 : 00000001
[ 1253.158755] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
[ 1253.165266] Control: 10c0383d Table: 5e71006a DAC: 00000055
[ 1253.172472] Process swapper/0 (pid: 0, stack limit = 0x60870141)
[ 1253.458055] [<7f9387b8>] (ath11k_spectral_process_data [ath11k]) from [<7f917fdc>] (ath11k_dbring_buffer_release_event+0x214/0x2e4 [ath11k])
[ 1253.466139] [<7f917fdc>] (ath11k_dbring_buffer_release_event [ath11k]) from [<7f8ea3c4>] (ath11k_wmi_tlv_op_rx+0x1840/0x29cc [ath11k])
[ 1253.478807] [<7f8ea3c4>] (ath11k_wmi_tlv_op_rx [ath11k]) from [<7f8fe868>] (ath11k_htc_rx_completion_handler+0x180/0x4e0 [ath11k])
[ 1253.490699] [<7f8fe868>] (ath11k_htc_rx_completion_handler [ath11k]) from [<7f91308c>] (ath11k_ce_per_engine_service+0x2c4/0x3b4 [ath11k])
[ 1253.502386] [<7f91308c>] (ath11k_ce_per_engine_service [ath11k]) from [<7f9a4198>] (ath11k_pci_ce_tasklet+0x28/0x80 [ath11k_pci])
[ 1253.514811] [<7f9a4198>] (ath11k_pci_ce_tasklet [ath11k_pci]) from [<8032227c>] (tasklet_action_common.constprop.2+0x64/0xe8)
[ 1253.526476] [<8032227c>] (tasklet_action_common.constprop.2) from [<803021e8>] (__do_softirq+0x130/0x2d0)
[ 1253.537756] [<803021e8>] (__do_softirq) from [<80322610>] (irq_exit+0xcc/0xe8)
[ 1253.547304] [<80322610>] (irq_exit) from [<8036a4a4>] (__handle_domain_irq+0x60/0xb4)
[ 1253.554428] [<8036a4a4>] (__handle_domain_irq) from [<805eb348>] (gic_handle_irq+0x4c/0x90)
[ 1253.562321] [<805eb348>] (gic_handle_irq) from [<80301a78>] (__irq_svc+0x58/0x8c)
Tested-on: QCN6122 hw1.0 AHB WLAN.HK.2.6.0.1-00851-QCAHKSWPL_SILICONZ-1
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1649396345-349-1-git-send-email-quic_haric@quicinc.com
|
|
Currently, WBM idle ring HP is updated much before the shadow
configuration is sent to the FW. Any update to the shadow
registers before FW mode on request would not be reflected
on to the actual HW registers failing to bring up the device.
Send FW mode ON QMI request before WBM idle ring HP update
to fix this problem.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220406094107.17878-12-quic_mpubbise@quicinc.com
|
|
WCN6750 is a single PDEV non-DBS chip which supports 2G, 5G and 6G bands.
It is a single LMAC device which can be either hooked to 2G/5G/6G bands.
Add WMI changes to support WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220406094107.17878-11-quic_mpubbise@quicinc.com
|
|
Though WCN6750 is a single PDEV device, it is not a
DBS solution. So, do not put HW in DBS mode for WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220406094107.17878-10-quic_mpubbise@quicinc.com
|
|
drivers/net/wireless/ath/ath11k/mac.c:8175:13: error: ‘ath11k_mac_op_ipv6_changed’ defined but not used [-Werror=unused-function]
static void ath11k_mac_op_ipv6_changed(struct ieee80211_hw *hw,
^~~~~~~~~~~~~~~~~~~~~~~~~~
Wrap it with #ifdef block to fix this.
Fixes: c3c36bfe998b ("ath11k: support ARP and NS offload")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220411020843.10284-1-yuehaibing@huawei.com
|
|
Add the missing unlock before return from function ath11k_wow_op_resume()
in the error handling case.
Fixes: 90bf5c8d0f7e ("ath11k: purge rx pktlog when entering WoW")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220408030912.3087293-1-yangyingliang@huawei.com
|
|
Add ath11k_mac_op_set_bios_sar_specs() to ath11k_ops, this function is called
when user space application calls NL80211_CMD_SET_SAR_SPECS. ath11k also
registers SAR type and frequency ranges to wiphy so user space can query SAR
capabilities.
This feature is currently enabled for WCN6855.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02431-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401120948.1312956-3-quic_bqiang@quicinc.com
|
|
When the WMI service bits are reported from firmware they are divided into
multiple segments, with 128 bits in each segment. The first segment is
processed by ath11k_wmi_service_bitmap_copy(), the second segment is processed
by ath11k_service_available_event() with WMI_TAG_SERVICE_AVAILABLE_EVENT. When
the service bit exceed 256 bits, then firmware reports it by tag
WMI_TAG_ARRAY_UINT32 in WMI_SERVICE_AVAILABLE_EVENTID.
Currently ath11k does not process the third segment. Upcoming features
need to know if firmware support is available for the features, so add
processing of the third segment.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401120948.1312956-2-quic_bqiang@quicinc.com
|
|
There is a spelling mistake in an ath11k_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220407102820.613881-1-colin.i.king@gmail.com
|
|
Currently in mac80211 each STA object is represented
using sta_info datastructure with the associated
STA specific information and drivers access ieee80211_sta
part of it.
With MLO (Multi Link Operation) support being added
in 802.11be standard, though the association is logically
with a single Multi Link capable STA, at the physical level
communication can happen via different advertised
links (uniquely identified by Channel, operating class,
BSSID) and hence the need to handle multiple link
STA parameters within a composite sta_info object
called the MLD STA. The different link STA part of
MLD STA are identified using the link address which can
be same or different as the MLD STA address and unique
link id based on the link vif.
To support extension of such a model, the sta_info
datastructure is modified to hold multiple link STA
objects with link specific params currently within
sta_info moved to this new structure. Similarly this is
done for ieee80211_sta as well which will be accessed
within mac80211 as well as by drivers, hence trivial
driver changes are expected to support this.
For current non MLO supported drivers, only one link STA
is present and link information is accessed via 'deflink'
member.
For MLO drivers, we still need to define the APIs etc. to
get the correct link ID and access the correct part of
the station info.
Currently in mac80211, all link STA info are accessed directly
via deflink. These will be updated to access via link pointers
indexed by link id with MLO support patches, with link id
being 0 for non MLO supported cases.
Except for couple of macro related changes, below spatch takes
care of updating mac80211 and driver code to access to the
link STA info via deflink.
@ieee80211_sta@
struct ieee80211_sta *s;
struct sta_info *si;
identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr};
@@
(
s->
- var
+ deflink.var
|
si->sta.
- var
+ deflink.var
)
@sta_info@
struct sta_info *si;
identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth};
@@
(
si->
- var
+ deflink.var
)
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com
[remove MLO-drivers notes from commit message, not clear yet; run spatch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add ieee80211_rx_check_bss_color_collision routine in order to introduce
BSS color collision detection in mac80211 if it is not supported in HW/FW
(e.g. for mt7915 chipset).
Add IEEE80211_HW_DETECTS_COLOR_COLLISION flag to let the driver notify
BSS color collision detection is supported in HW/FW. Set this for ath11k
which apparently didn't need this code.
Tested-by: Peter Chiu <Chui-Hao.Chiu@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/a05eeeb1841a84560dc5aaec77894fcb69a54f27.1648204871.git.lorenzo@kernel.org
[clarify commit message a bit, move flag to mac80211]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
No need to have goto for a return statement, so simplify the code. While at it,
print warning messages if power up calls fail.
No functional changes.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401173042.17467-4-kvalo@kernel.org
|
|
While reviewing the mhi.c I noticed we were just ignoring the errors coming
from MHI subsystem during suspend and resume. Add proper checks and warning
messages. Also pass the error value to callers.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401173042.17467-3-kvalo@kernel.org
|
|
State machines are difficult to understand and in this case it's just useless,
which is shown by the diffstat. So remove it entirely to make the code simpler.
No functional changes.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401173042.17467-2-kvalo@kernel.org
|
|
In the "ath11k_wow_init", error value "EINVAL" is returned
when the check for firmware support of WoW feature fails,
which in turn stops the driver initialization.
Warning message:
[ 31.040144] ------------[ cut here ]------------
[ 31.040185] WARNING: CPU: 1 PID: 51 at drivers/net/wireless/ath/ath11k/wow.c:813 ath11k_wow_init+0xc8/0x13a8 [ath11k]
[ 31.043846] Modules linked in: ath11k_pci ath11k qmi_helpers
[ 31.054341] CPU: 1 PID: 51 Comm: kworker/u8:1 Tainted: G W 5.17.0-wt-ath-594817-ga7f6aa925cf8-dirty #17
[ 31.060078] Hardware name: Qualcomm Technologies, Inc. IPQ8074/AP-HK10-C2 (DT)
[ 31.070578] Workqueue: ath11k_qmi_driver_event ath11k_qmi_driver_event_work [ath11k]
[ 31.077782] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 31.085676] pc : ath11k_wow_init+0xc8/0x13a8 [ath11k]
[ 31.092359] lr : ath11k_mac_register+0x548/0xb98 [ath11k]
[ 31.097567] sp : ffff80000aa13c40
[ 31.102944] x29: ffff80000aa13c40 x28: ffff800009184390 x27: ffff000002959f20
[ 31.106251] x26: ffff000002828000 x25: ffff000002830000 x24: ffff000002830000
[ 31.113369] x23: ffff000002820000 x22: ffff00000282854c x21: 0000000000000000
[ 31.120487] x20: ffff00000295cf20 x19: ffff000002828540 x18: 0000000000000031
[ 31.127605] x17: 0000000000000004 x16: ffff0000028285fc x15: ffff00000295b040
[ 31.134723] x14: 0000000000000067 x13: ffff00000282859c x12: 000000000000000d
[ 31.141840] x11: 0000000000000018 x10: 0000000000000004 x9 : 0000000000000000
[ 31.148959] x8 : ffff00000289d680 x7 : 0000000000000000 x6 : 000000000000003f
[ 31.156077] x5 : 0000000000000040 x4 : 0000000000000000 x3 : ffff000002820968
[ 31.163196] x2 : 0000000000000080 x1 : 0080008af9981779 x0 : ffff000002959f20
[ 31.170314] Call trace:
[ 31.177421] ath11k_wow_init+0xc8/0x13a8 [ath11k]
[ 31.179684] ath11k_core_qmi_firmware_ready+0x430/0x5e0 [ath11k]
[ 31.184548] ath11k_qmi_driver_event_work+0x16c/0x4f8 [ath11k]
[ 31.190623] process_one_work+0x134/0x350
[ 31.196262] worker_thread+0x12c/0x450
[ 31.200340] kthread+0xf4/0x110
[ 31.203986] ret_from_fork+0x10/0x20
[ 31.207026] ---[ end trace 0000000000000000 ]---
[ 31.210894] ath11k_pci 0000:01:00.0: failed to init wow: -22
[ 31.215467] ath11k_pci 0000:01:00.0: failed register the radio with mac80211: -22
[ 31.221117] ath11k_pci 0000:01:00.0: failed to create pdev core: -22
Fix this by returning value "0" when FW doesn't support WoW
to allow driver to proceed with initialize sequence and also
remove the unnecessary "WARN_ON".
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: ba9177fcef21 ("ath11k: Add basic WoW functionalities")
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220331073110.3846-1-quic_nmaran@quicinc.com
|
|
The intended delay in ath11k_core_suspend is introduced in commit
d1b0c33850d2 ("ath11k: implement suspend for QCA6390 PCI devices"),
now with ath11k_mac_wait_tx_complete added in commit ba9177fcef21
("ath11k: Add basic WoW functionalities"), that delay is not
necessary now, so remove it.
This is found in code review.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02431-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220331002105.1162099-1-quic_bqiang@quicinc.com
|
|
The maximum number of SSIDs in a for active probe requests is currently
reported as 16 (WLAN_SCAN_PARAMS_MAX_SSID) when registering the driver.
The scan_req_params structure only has the capacity to hold 10 SSIDs.
This leads to a buffer overflow which can be triggered from
wpa_supplicant in userspace. When copying the SSIDs into the
scan_req_params structure in the ath11k_mac_op_hw_scan route, it can
overwrite the extraie pointer.
Firmware supports 16 ssid * 4 bssid, for each ssid 4 bssid combo probe
request will be sent, so totally 64 probe requests supported. So
set both max ssid and bssid to 16 and 4 respectively. Remove the
redundant macros of ssid and bssid.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01300-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220329150221.21907-1-quic_kathirve@quicinc.com
|
|
Remove core PCI and ath11k PCI references(struct ath11k_pci)
from PCI common code. Since, PCI common code will be used
by hybrid bus devices, this code should be independent
from ATH11K PCI references and Linux core PCI references
like struct pci_dev.
Since this change introduces function callbacks for bus wakeup
and bus release operations, wakeup_mhi HW param is no longer
needed and hence it is removed completely. Alternatively, bus
wakeup/release ops for QCA9074 are initialized to NULL as
QCA9704 does not need bus wakeup/release for register accesses.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-6-quic_mpubbise@quicinc.com
|
|
Refactor MSI logic in order to support hybrid bus devices
like WCN6750.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-5-quic_mpubbise@quicinc.com
|
|
Instead of selecting MSI config based on magic numbers, make
the assignment based on HW revision. The logic is similar to
the selection of HW params. This improves readability of the
code and also simplifies new additions.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-4-quic_mpubbise@quicinc.com
|
|
Unlike other ATH11K PCIe devices which are enumerated by APSS
processor (Application Processor SubSystem), WCN6750 gets
enumerated by the WPSS Q6 processor (Wireless Processor SubSystem);
In simple terms, though WCN6750 is PCIe device, it is not attached
to the APSS processor, APSS will not know of such a device being
present in the system and therefore WCN6750 will be registered as
a platform device to the kernel core like other supported AHB
devices.
WCN6750 needs both AHB and PCI APIs for it's operation, it uses
AHB APIs for device probe/boot and PCI APIs for device setup and
register accesses. Because of this nature, it is referred as a
hybrid bus device.
Refactor PCI code to support hybrid bus devices like WCN6750.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-3-quic_mpubbise@quicinc.com
|
|
In order to add the support for WCN6750 in ATH11K , it is
required to move certain PCI definitions to the header file.
As a result, add ATH11K_PCI_* prefix to these definitions.
Also, change the scope of certain PCI APIs that are required
to enable WCN6750 from static to global.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-2-quic_mpubbise@quicinc.com
|
|
This reverts commit 743b9065fe6348a5f8f5ce04869ce2d701e5e1bc.
The original commit breaks the 256 bitmap in blockack frames in AP
mode. After reverting the commit the feature works again in both AP and
mesh modes
Tested-on: IPQ8074 hw2.0 PCI WLAN.HK.2.6.0.1-00786-QCAHKSWPL_SILICONZ-1
Fixes: 743b9065fe63 ("ath11k: mesh: add support for 256 bitmap in blockack frames in 11ax")
Signed-off-by: Anilkumar Kolli <quic_akolli@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1648701477-16367-1-git-send-email-quic_akolli@quicinc.com
|
|
Currently ath11k will wait 11d scan complete while add interface in
ath11k_mac_op_add_interface(), when system resume without enable
wowlan, ath11k_mac_op_add_interface() is called for each resume, thus
it increase the resume time of system. And ath11k_mac_op_hw_scan()
after ath11k_mac_op_add_interface() also needs some time cost because
the previous 11d scan need more than 5 seconds when 6 GHz is enabled,
then the scan started event will indicated to ath11k after the 11d
scan completed.
While 11d scan/hw scan is running in firmware, if ath11k update channel
list to firmware by WMI_SCAN_CHAN_LIST_CMDID, then firmware will cancel
the current scan which is running, it lead the scan failed. The patch
commit 9dcf6808b253 ("ath11k: add 11d scan offload support") used
finish_11d_scan/finish_11d_ch_list/pending_11d to synchronize the 11d
scan/hw scan/channel list between ath11k/firmware/mac80211 and to avoid
the scan fail.
Add wait operation before ath11k update channel list, function
ath11k_reg_update_chan_list() will wait until the current 11d scan/hw
scan completed. And remove the wait operation of start 11d scan and
waiting channel list complete in hw scan. After these changes, resume
time cost reduce about 5 seconds and also hw scan time cost reduced
obviously, and scan failed not seen.
The 11d scan is sent to firmware only one time for each interface added
in mac.c, and it is moved after the 1st hw scan because 11d scan will
cost some time and thus leads the AP scan result update to UI delay.
Currently priority of ath11k's hw scan is WMI_SCAN_PRIORITY_LOW, and
priority of 11d scan in firmware is WMI_SCAN_PRIORITY_MEDIUM, then the
11d scan which sent after hw scan will cancel the hw scan in firmware,
so change the priority to WMI_SCAN_PRIORITY_MEDIUM for the hw scan which
is in front of the 11d scan, thus it will not happen scan cancel in
firmware.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 9dcf6808b253 ("ath11k: add 11d scan offload support")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328035832.14122-1-quic_wgong@quicinc.com
|