summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/wil6210/cfg80211.c
AgeCommit message (Collapse)AuthorFilesLines
2014-05-29wil6210: detect scan timeoutsVladimir Kondratiev1-0/+1
If scan has not finished in some reasonable time (10sec), interpret it as if firmware error occurs but was not reported. Firmware should report scan completion for every scan request, so it is error condition indeed. Perform firmware recovery procedure. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-19cfg80211: constify MAC addresses in cfg80211 opsJohannes Berg1-2/+2
This propagates through all the drivers and mac80211. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-03-17wil6210: fix race between disconnect and Tx NAPIVladimir Kondratiev1-0/+4
When disconnecting some CID, corresponded Tx vring get released. During vring release, all descriptors get freed. It is possible that Tx NAPI working on the same vring simultaneously. If it happens, descriptor may be double freed. To protect from the race above, make sure NAPI won't process the same vring. Introduce 'enabled' flag in the struct vring_tx_data. Proceed with Tx NAPI only if 'enabled' flag set. Prior to Tx vring release, clear this flag and make sure NAPI get synchronized. NAPI enablement status protected by wil->mutex, add protection where it was missing and check for it. During reset, disconnect all peers first, then proceed with the Rx vring. It allows for the disconnect flow to observe proper 'wil->status' and correctly notify cfg80211 about connection status change Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: serialize fw_recovery and start_apVladimir Kondratiev1-4/+11
These methods can change device state, serialize with others similar ones like up/down Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: fix secondary connectVladimir Kondratiev1-0/+4
when STA receiving connect() when already connected, it should return error Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: fw error recoveryVladimir Kondratiev1-1/+7
upon fw error interrupt - in STA mode, disconnect/cancel scan and then reset FW/HW added module param - no_fw_recovery which is false by default Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: reduce printingVladimir Kondratiev1-2/+2
Convert 2 often printed messages to dynamic ones Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: enable scan while connectedVladimir Kondratiev1-6/+2
New firmware do support scan while connected. Enable it. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-04wil6210: fix smatch warning in wil_cfg80211_get_station()Vladimir Kondratiev1-1/+1
Smatch suggests to propagate error code from wil_find_cid(), and, indeed, it is a good idea. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: single station disconnectVladimir Kondratiev1-0/+9
implement del_station() method in the struct cfg80211_ops It allows to disconnect single peer from the AP Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: Provide signal strength indicationVladimir Kondratiev1-3/+4
When notifying about Rx mgmt (ex: during scan), extract signal strength reported by the hardware. signal is not MBM, it is arbitrary units 0..100 Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: per-connection statisticsVladimir Kondratiev1-3/+33
Calculate statistics per connection, report with "iw station dump" Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: dump_station initial supportVladimir Kondratiev1-16/+66
Rx stats is not calculated per STA - just give some number Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: multiple connect - initial supportVladimir Kondratiev1-2/+6
Enable multiple (up to 8 - HW/FW limitation) simultaneous connections. Each connection has its own CID (connection ID) that describes chip's beam-forming entity. Tx Vring should refer to correct CID for frame to reach its destination. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: Tx management frameVladimir Kondratiev1-0/+72
Implement management frame passing. In order to receive frame on the other side, remain_on_channel() should be implemented as well Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-03net:drivers/net: Miscellaneous conversions to ETH_ALENJoe Perches1-2/+2
Convert the memset/memcpy uses of 6 to ETH_ALEN where appropriate. Also convert some struct definitions and u8 array declarations of [6] to ETH_ALEN. Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-12wil6210: Init Rx vring right after resetVladimir Kondratiev1-2/+5
at the vring initialisation, memory pool get allocated in the FW. Make it 1-st because FW need this memory pool to precess next commands Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12wil6210: Derive IE's for APVladimir Kondratiev1-0/+27
When starting secure AP, in some cases wpa_s provides probe template but not probe/assoc IE's. In this case, derive missing IE's from probe. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-29wil6210: Don't use wdev->sme_stateVladimir Kondratiev1-0/+4
sme_state is private wdev's variable. Track connection state internally Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-13wil6210: sync with new firmwareVladimir Kondratiev1-9/+3
Adjust driver for changes in the FW API. Noticeable changes in the FW are: - temperature sensing - infrastructure for multiple connections - infrastructure for P2P - signal strength indication This commit introduces only changes that are required to support same functionality as previous firmware, no new features. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-13wil6210: headers clean-upVladimir Kondratiev1-9/+0
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-13wil6210: use WLAN_CAPABILITY_DMG_TYPE_MASKVladimir Kondratiev1-1/+1
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-13wil6210: do not set IE's for beaconVladimir Kondratiev1-2/+7
On the DMG band, there is no 'normal' beacon frame. Instead, transmitted is short 'DMG beacon' frame, that do not include IE's So, beacon IE's are not relevant for the DMG band. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-13wil6210: remove unused including <linux/version.h>Wei Yongjun1-1/+0
Remove including <linux/version.h> that don't need it. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-02-11cfg80211: pass wiphy to cfg80211_ref_bss/put_bssJohannes Berg1-1/+1
This prepares for using the spinlock instead of krefs which is needed in the next patch to track the refs of combined BSSes correctly. Acked-by: Bing Zhao <bzhao@marvell.com> [mwifiex] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-31wil6210: checkpatch warningsVladimir Kondratiev1-1/+0
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-31wil6210: fix checkpatch CamelCase warningsVladimir Kondratiev1-2/+2
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-31wil6210: remove raw wil_dbg() callsVladimir Kondratiev1-4/+4
Introduce debug category "MISC", convert all raw wil_dbg() to this category. This improves dynamic debug manageability Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-05wireless: add new wil6210 802.11ad 60GHz driverVladimir Kondratiev1-0/+573
This adds support for the 60 GHz 802.11ad Wilocity card through a new driver, wil6210. Wilocity implemented the firmware, QCA maintains the device driver. Currently supported: - STA: with security - AP: limited to 1 connected STA, security disabled - Monitor: due to a hardware/firmware limitation either control or non-control frames are monitored Using a STA and AP with this drive, one can assemble a fully functional BSS. Throughput of 1.2Gbps is achieved with iperf. The wil6210 cards have on-board flash memory for the firmware, the cards comes pre-flashed and no firmware download is required. For more details see: http://wireless.kernel.org/en/users/Drivers/wil6210 Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-07-26 04:36:58 +0300