Age | Commit message (Collapse) | Author | Files | Lines |
|
Some devices, like the Comfast CF-826F, use LED1, which already works.
Others, like Asus USB-N13 C1, use LED0, which doesn't work correctly.
Write the right values to the LED control registers to make LED0 work
as well.
This is unfortunately tested only with the Comfast CF-826F.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/7a2c3158-3a45-4466-b11e-fc09802b20e2@gmail.com
|
|
Give proper names:
RF6052_REG_UNKNOWN_56 -> RF6052_REG_PAD_TXG
RF6052_REG_UNKNOWN_DF -> RF6052_REG_GAIN_CCA
And fix typos:
REG_OFDM0_AGCR_SSI_TABLE -> REG_OFDM0_AGC_RSSI_TABLE
REG_BB_ACCEESS_CTRL -> REG_BB_ACCESS_CTRL
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/40157253-76bd-8b23-06e0-3365139b5395@gmail.com
|
|
This is a newer chip, similar to the RTL8710BU in that it uses the same
PHY status structs.
Features: 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps.
It can allegedly have Bluetooth, but that's not implemented here.
This chip can have many RFE (RF front end) types, of which types 1
and 5 are the only ones tested. Many of the other types need different
initialisation tables. They can be added if someone wants them.
The vendor driver v5.8.6.2_35538.20191028_COEX20190910-0d02 from
https://github.com/BrightX/rtl8192fu was used as reference, with
additional device IDs taken from
https://github.com/kelebek333/rtl8192fu-dkms.
The vendor driver also claims to support devices with ID 0bda:a725,
but that is found in some bluetooth-only devices, so it's not supported
here.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/7dcf9fb9-1c97-ac28-5286-2236e287a18c@gmail.com
|
|
Use the sequence from the vendor driver for setting up the beacon
related registers.
Also set the MAC address register here, in case the MAC address for the
new interface should be different from what was set in
rtl8xxxu_init_device(). This happens for example with the hostapd config
option "bssid".
Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230428150833.218605-7-martin.kaistra@linutronix.de
|
|
Add a workqueue to update the beacon contents asynchronously and
implement downloading the beacon to the HW and starting beacon tx like
the vendor driver.
Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230428150833.218605-4-martin.kaistra@linutronix.de
|
|
This chip is found in cheap "free driver" USB adapters from Aliexpress.
Initially they pretend to be a CD-ROM containing the driver for Windows.
"Ejecting" switches the device to wifi mode.
Features: 2.4 GHz, b/g/n mode, 1T1R, 150 Mbps.
This chip is more unique than other Realtek chips:
* The registers at addresses 0x0-0xff, which all the other chips use,
can't be used here. New registers at 0x8000-0x80ff must be used
instead. And it's not a simple matter of adding 0x8000: 0x2
(REG_SYS_FUNC) became 0x8004, 0x80 (REG_MCU_FW_DL) became 0x8090,
etc.
* Also there are a few new registers which must be accessed indirectly
because their addresses don't fit in 16 bits. No other chips seem to
have these.
* The vendor driver compiles to 8188gu.ko, but the code calls the chip
RTL8710B(U) pretty much everywhere, including messages visible to the
user.
Another difference compared to the other chips supported by rtl8xxxu is
that it has a new PHY status struct, or three of them actually, from
which we extract the RSSI, among other things. This is not unique,
though, just new. The chips supported by rtw88 also use it.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> # Edimax N150
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/4edbe29f-00b9-8eef-9789-20bed0b141e2@gmail.com
|
|
By default the LED will blink when there is some activity.
This was tested with a cheap "HT-WR813" from Aliexpress.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/8f7fd5d7-5baa-b38b-ad2a-977dcd9edd81@gmail.com
|
|
By default the LED will blink when there is some activity.
This was tested with a TP-Link TL-WN725N.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/34d62bf5-3595-0c77-2ca7-be78555f765d@gmail.com
|
|
This chip is found in cheap USB devices from TP-Link, D-Link, etc.
Features: 2.4 GHz, b/g/n mode, 1T1R, 150 Mbps.
Chip versions older than "I cut" need software rate control. That will
be in the next commit. Until then MCS7 is used for all data frames.
The "I cut" chips are not supported. They require different firmware
and initialisation tables. Support can be added if someone has the
hardware to test it.
Co-developed-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Co-developed-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Co-developed-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/3aad60f6-23f9-81e8-c741-4bd51e99f423@gmail.com
|
|
It simplifies the code a bit.
Suggested-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/68f94284-3728-7b75-2b7b-64fae8af6bc5@gmail.com
|
|
Use descriptive names instead of magic numbers.
Suggested-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/e7d05bd9-e096-8361-f1b4-3c8b8599a7eb@gmail.com
|
|
The CCK RSSI calculation is incorrect for the RTL8723BU, RTL8192EU,
and RTL8188FU. Add new functions for these chips with code copied from
their vendor drivers. Use the old code only for the RTL8723AU and
RTL8192CU.
I didn't notice any difference in the reported signal strength with my
RTL8188FU, but I didn't look very hard either.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/926c838f-4997-698b-4da9-44582e2af99a@gmail.com
|
|
According to Realtek programmers, "to adjust oscillator to align
central frequency of connected AP. Then, it can yield better
performance." From commit fb8517f4fade ("rtw88: 8822c: add CFO
tracking").
The RTL8192CU and a version of RTL8723AU apparently don't have the
ability to adjust the oscillator, so this doesn't apply to them.
This also doesn't apply to the wifi + bluetooth combo chips (RTL8723AU
and RTL8723BU) because the CFO tracking should only be done when
bluetooth is disabled, and determining that looked complicated.
That leaves only the RTL8192EU and RTL8188FU chips. I tested this with
the latter.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/80aba428-0aff-f4b2-dea5-35d1425982b6@gmail.com
|
|
This chip is found in the cheapest USB adapters, e.g. 1.17 USD with
VAT and shipping from China included.
It's a gen 2 chip, similar to the RTL8723BU, but without Bluetooth.
Features: 2.4 GHz, b/g/n mode, 1T1R, 150 Mbps.
The vendor driver rtl8188fu version 4.3.23.6_20964.20170110 [0]
was used as reference. The CD shipped with the device includes a
newer driver, version 5.11.5-1-g12f7cde4b.20201102, but that one
couldn't complete the WPA2 key exchange thing for whatever reason.
[0] https://github.com/kelebek333/rtl8188fu
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/b14f299d-3248-98fe-eee1-ba50d2e76c74@gmail.com
|
|
According to the Realtek propritary driver and the rtw88 driver, the
tx rates of the ack (includes block ack) are initialized with lower
tx rates (no HT rates) which is set by the RRSR register value. In
real cases, ack rate higher than current tx rate could lead to
difficulty for the receiving end to receive management/control frames.
The retransmission rate would be higher then expected when the driver
is acting as receiver and the RSSI is not good.
Cross out higer rates for ack packet before implementing dynamic rrsr
configuration like the commit 4830872685f8 ("rtw88: add dynamic rrsr
configuration").
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211001040044.1028708-1-chris.chiu@canonical.com
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 64 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.894819585@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Update copyright year and email address.
Signed-off-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This powers down the 8192e correctly, or at least to the point where
the firmware will load again, when reloading the driver module.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
These are primarily needed for SDIO/PCI parts, but the vendor driver
still sets them for some USB devices.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This adds TX antenna selection bit defines for OFDM mode.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This also renames REG_USB_AGG_{TO,TH} to REG_USB_AGG_{TIMEOUT,THRESH}
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Documentation for enabling USB aggregation and whether to select
interrupt or bulk delivery of interrupt events.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This reduce the use of magic values a little.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Longer term we should switch all the chips over to use this function
instead of the random chip specific ifdef hacks.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Adjust AFE before enabling PLL on 8192eu, probably also needed for
8723bu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
8192eu has it's own IQK calibration procedure, and notably uses
undocumented RF register 0x56 in the process.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Set REG_QUEUE_CTRL and REG_ACLK_MON for 8192eu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The vendor driver set register 0xfe58 REG_USB_HWPWM in it's init
sequence for 8192eu. Do the same here.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Improve descriptive names of some registers and add some additional
registers only found on nextgen chips.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This should help when reloading the driver for 8723bu devices
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Implment 8723bu specific device power down, and make power_off() a
fileops function.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use the bit define rather than hard code the value for REG_PWR_DATA bits.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Provide RF_T_METER register location for nextgen chips.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Vendor driver implements this for 8723b and 8821 series
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This initializes RX DMA aggregation on 8723bu. We should do this for
all parts eventually, and also init TX aggregation.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
List yet another new register found on the 8723b.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Implement burst parameter sequence for 8723bu parts. Eventually this
should be moved into device specific sections.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This implements the 8723bu specific power on sequence as it is
different from that of the 8723au chips.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Implement additional init sequence code for the 8723bu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This should initialize the antennas on the 8723bu, but so far I am
still not receiving anything :( More work is needed.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a first stab of implementing rtl8723bu_config_channel(). For
now this will only do 20MHz channels.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The 8723bu also has it's own IQK calibration process. This is similar
in flow, but still different enough to warrent it's own
implementation, at least for now.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This adds some additional register definitions for 8723bu, as well as
a bit define for USB RXDMA aggregation in REG_RXDMA_AGG_PG_TH.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This introduces additional register definitions for newer generation
chips.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The newer generation chips have different interrupt registers.
Initialize this correct registers on 8192eu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The 8192eu (and some other parts) will report an incorrect USB OUT
EP. This tells the chip to drop it - as per the vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Newer chips can auto load the LLT table, it is no longer necessary to
build it manually in the driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This implements the rtl8192eu power on sequence, and splits it off
from the rtl8192cu/rtl8723au power on sequence.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This identifies the chip vendors correctly and also picks the correct
firmware for rtl8192eu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|