| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
USB and (upcoming) SDIO support may sleep in the read/write handlers.
Shrink the RCU critical section so it only cover the call to
ieee80211_find_sta() and finding the ic_vht_cap/vht_cap based on the
found station. This moves the chip's BFEE configuration outside the
rcu_read_lock section and thus prevent "scheduling while atomic" or
"Voluntary context switch within RCU read-side critical section!"
warnings when accessing the registers using an SDIO card (which is
where this issue has been spotted in the real world - but it also
affects USB cards).
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230108211324.442823-2-martin.blumenstingl@googlemail.com
|
|
Since chip_info has became const table, we must access them via const
pointer to avoid invalid writing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220727065232.28510-1-pkshih@realtek.com
|
|
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently in mac80211 each STA object is represented
using sta_info datastructure with the associated
STA specific information and drivers access ieee80211_sta
part of it.
With MLO (Multi Link Operation) support being added
in 802.11be standard, though the association is logically
with a single Multi Link capable STA, at the physical level
communication can happen via different advertised
links (uniquely identified by Channel, operating class,
BSSID) and hence the need to handle multiple link
STA parameters within a composite sta_info object
called the MLD STA. The different link STA part of
MLD STA are identified using the link address which can
be same or different as the MLD STA address and unique
link id based on the link vif.
To support extension of such a model, the sta_info
datastructure is modified to hold multiple link STA
objects with link specific params currently within
sta_info moved to this new structure. Similarly this is
done for ieee80211_sta as well which will be accessed
within mac80211 as well as by drivers, hence trivial
driver changes are expected to support this.
For current non MLO supported drivers, only one link STA
is present and link information is accessed via 'deflink'
member.
For MLO drivers, we still need to define the APIs etc. to
get the correct link ID and access the correct part of
the station info.
Currently in mac80211, all link STA info are accessed directly
via deflink. These will be updated to access via link pointers
indexed by link id with MLO support patches, with link id
being 0 for non MLO supported cases.
Except for couple of macro related changes, below spatch takes
care of updating mac80211 and driver code to access to the
link STA info via deflink.
@ieee80211_sta@
struct ieee80211_sta *s;
struct sta_info *si;
identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr};
@@
(
s->
- var
+ deflink.var
|
si->sta.
- var
+ deflink.var
)
@sta_info@
struct sta_info *si;
identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth};
@@
(
si->
- var
+ deflink.var
)
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com
[remove MLO-drivers notes from commit message, not clear yet; run spatch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently all realtek wifi chip is set to check CRC of VHT-SIG-B
in 802.11ac signal, but some AP don't calculate the CRC and packets
from these AP can't be received and lead to disconnection.
We disable the check defaultly to avoid this case.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211217012421.7859-1-pkshih@realtek.com
|
|
Beamforming is used for directional signal transmission/reception.
Beamformee plays the role for signal reception, and makes the RX
performance better in middle distance range.
Implement beamformee related callbacks for 8821c.
Since 8821c only support 1ss rate, nc_index in beamformee setting
needs to be adjusted based on the capability.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-4-yhchuang@realtek.com
|
|
In the current design, various chip functions and tables
are built into rtw88 core. That causes kernel to load its
functionalities even if a chip isn't currently used. We
plan to make each chip's functionalities a separate
kernel module to reduce rtw88 core. And kernel will be
able to load the necessary.
Before extracting chip functionalities, we export symbols
inside rtw88 core which will be used in chip modules.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-2-yhchuang@realtek.com
|
|
8723D doesn't support beamform because rtw88 only supports VHT beamform
but 8723d doesn't have VHT capability. Though 8723d doesn't support
beamform, BSS_CHANGED_MU_GROUPS is still marked as changed when doing
disassociation. So, add wrapper functions for all beamform ops to make
sure they aren't NULL before calling.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420055054.14592-3-yhchuang@realtek.com
|
|
In associating and configuring beamformee, bfee->role is not
correctly set before rtw_chip_ops::config_bfee().
Fix it by setting it correctly.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Enable MU-MIMO transmit beamformee support for chipset 8822b and 8822c.
If the driver is in station mode and associated with an AP, and the
capabilities of both meet the requirement of beamforming, driver will
run as a beamformee and the corresponding chip settings will be set.
In addition, module parameter support_bf is added to enable or disable
beamforming. Sometimes driver will need to disable for inter-operate
issues, and it would be easier for driver to debug.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
