Age | Commit message (Collapse) | Author | Files | Lines |
|
All callers needs to work on mlx5_core_dev and it is already derived
before calling mlx5_devlink_eswitch_check().
Hence, accept mlx5_core_dev in mlx5_devlink_eswitch_check().
Given that it works on mlx5_core_dev change helper function name to
drop devlink prefix.
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Invoke mutex_destroy() to catch any esw state_lock errors.
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Annotate mutex destroy to keep it symmetric to init sequence.
It should be destroyed after its users (representor netdevices) are
destroyed in below flow.
esw_offloads_disable()
esw_offloads_unload_rep()
Hence, initialize the mutex before creating the representors which uses
it.
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Allow passing NULL spec when creating a flow rule. Such rules will act
as "catch all" flow rules.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Following introduction of per vport configuration of vport and rep,
unload all reps per rep type is still needed as IB reps can be
unloaded individually. However, a few internal functions exist purely
for this purpose, merge them to a single function.
This patch doesn't change any existing functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently, ECPF eswitch manager does one-time only configuration for
VF vports when device switches to offloads mode. However, when num of
VFs changed from host side, driver doesn't update VF vports
configurations.
Hence, perform VFs vport configuration update whenever num_vfs change
event occurs.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Both legacy and offload modes require vport setup, only offload mode
requires rep setup. Before this patch, vport and rep operations are
separated applied to all relevant vports in different stages.
Change to use per vport configuration, so that vport and rep operations
are modularized per vport.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Vport enable and disable sequence is incorrect. It should be:
enable()
esw_vport_setup_acl,
esw_vport_setup,
esw_vport_enable_qos.
disable()
esw_vport_disable_qos,
esw_vport_cleanup,
esw_vport_cleanup_acl.
Instead of having two setup functions for port and acl, merge
acl setup to port setup function.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Rename esw_apply_vport_config() to esw_vport_setup(), and add new
helper function esw_vport_cleanup() to make them symmetric.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
esw_vport_enable_qos can return error in cases below:
1. QoS is already enabled. Warnning is useless in this case.
2. Create scheduling element cmd failed. There is already a warning.
Remove the redundant warnning if esw_vport_enable_qos returns err.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Consider scenario below, CPU 1 is at risk to query already destroyed
drop counters. Need to apply the same state mutex when disabling vport.
+-------------------------------+-------------------------------------+
| CPU 0 | CPU 1 |
+-------------------------------+-------------------------------------+
| mlx5_device_disable_sriov | mlx5e_get_vf_stats |
| mlx5_eswitch_disable | mlx5_eswitch_get_vport_stats |
| esw_disable_vport | mlx5_eswitch_query_vport_drop_stats |
| mlx5_fc_destroy(drop_counter) | mlx5_fc_query(drop_counter) |
+-------------------------------+-------------------------------------+
Fixes: b8a0dbe3a90b ("net/mlx5e: E-switch, Add steering drop counters")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
esw_vport_create_legacy_acl_tables bails out immediately for eswitch
manager, hence remove all the check of esw manager cap after.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Minor overlapping changes, nothing serious.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to unlock before returning if this allocation fails.
Fixes: 75f36270990c ("octeontx2-pf: Support to enable/disable pause frames via ethtool")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the bounds check on index is off by one and can lead to
an out of bounds access on array priv->filters_loc when index is
RXCHK_BRCM_TAG_MAX.
Fixes: bb9051a2b230 ("net: systemport: Add support for WAKE_FILTER")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far we have the unfortunate situation that mdio_bus_phy_may_suspend()
is called in suspend AND resume path, assuming that function result is
the same. After the original change this is no longer the case,
resulting in broken resume as reported by Geert.
To fix this call mdio_bus_phy_may_suspend() in the suspend path only,
and let the phy_device store the info whether it was suspended by
MDIO bus PM.
Fixes: 503ba7c69610 ("net: phy: Avoid multiple suspends")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clear action, as with software, removes all ct metadata from
the packet.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mark packets with a unique tupleid, and on miss use that id to get
the act ct restore_cookie. Using that restore cookie, we ask CT to
restore the relevant info on the SKB.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register driver callbacks with the nf flow table platform.
FT add/delete events will create/delete FTE in the CT/CT_NAT tables.
Restoring the CT state on miss will be added in the following patch.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for offloading tc ct action and ct matches.
We translate the tc filter with CT action the following HW model:
+-------------------+ +--------------------+ +--------------+
+ pre_ct (tc chain) +----->+ CT (nat or no nat) +--->+ post_ct +----->
+ original match + | + tuple + zone match + | + fte_id match + |
+-------------------+ | +--------------------+ | +--------------+ |
v v v
set chain miss mapping set mark original
set fte_id set label filter
set zone set established actions
set tunnel_id do nat (if needed)
do decap
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, we write chain register mapping on miss from the the last
prio of a chain. It is used to restore the chain in software.
To support re-using the chain register mapping from global tables (such
as CT tuple table) misses, export the chain mapping.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FTEs in global tables may match on packets from multiple in_ports.
Provide the capability to omit the in_port match condition.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, flow tables are automatically connected according to their
<chain,prio,level> tuple.
Introduce global tables which are flow tables that are detached from the
eswitch chains processing, and will be connected by explicitly referencing
them from multiple chains.
Add this new table type, and allow connecting them by refenece.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The eswitch offloads table, which has the reps (vport) rx miss rules,
was moved from OFFLOADS namespace [0,0] (prio, level), to [1,0], so
the restore table (the new [0,0]) can come before it. The destinations
of these miss rules is the rep root ft (ttc for non uplink reps).
Uplink rep root ft is created as OFFLOADS namespace [0,1], and is used
as a hook to next RX prio (either ethtool or ttc), but this fails to
pass fs_core level's check.
Move uplink rep root ft to OFFLOADS prio 1, level 1 ([1,1]), so it
will keep the same relative position after the restore table
change.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable reg c1 loopback if firmware reports it's supported,
as this is needed for restoring packet metadata (e.g chain).
Also define helper to query if it is enabled.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
|
|
Currently, PF missed to clear the port base VLAN for VF when
unload. In this case, the VLAN id will remain in the VLAN
table. This patch fixes it.
Fixes: 92f11ea177cd ("net: hns3: fix set port based VLAN issue for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the user manual, the ingress and egress VLAN filter
are configured at the same time. Currently, hclge_init_vlan_config()
and hclge_set_vlan_spoofchk() will both change the VLAN filter
switch. So it's necessary to read the old configuration before
modifying it.
Fixes: 22044f95faa0 ("net: hns3: add support for spoof check setting")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, if VF is loaded on the host side, the host doesn't
clear the VF's VLAN table entries when VF removing. In this
case, when doing reset and disabling sriov at the same time the
VLAN device over VF will be removed, but the VLAN table entries
in hardware are remained.
This patch fixes it by asking PF to clear the VLAN table entries for
VF when VF is removing. It also clears the VLAN table full bit
after VF VLAN table entries being cleared.
Fixes: c6075b193462 ("net: hns3: Record VF vlan tables")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The HNS3 driver supports to configure TC numbers and TC to priority
map via "tc" tool. But when delete the rule, will fail, because
the HNS3 driver needs at least one TC, but the "tc" tool sets TC
number to zero when delete.
This patch makes sure that the TC number is at least one.
Fixes: 30d240dfa2e8 ("net: hns3: Add mqprio hardware offload support in hns3 driver")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver was rejecting almost all unsupported
parameters already, it was only missing a check
for tx_max_coalesced_frames_irq.
As a side effect of these changes the error code for
unsupported params changes from ENOTSUPP to EOPNOTSUPP.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver was rejecting almost all unsupported
parameters already, it was only missing a check
for tx_max_coalesced_frames_irq.
As a side effect of these changes the error code for
unsupported params changes from ENOTSUPP to EOPNOTSUPP.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters
(other than adaptive rx, which will now be rejected by core).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Converting fallthrough comments to fallthrough; creates warnings
in this code when compiled with gcc.
This code is overly complicated and reads rather better with a
little refactoring and no fallthrough uses at all.
Remove the fallthrough comments and simplify the written source
code while reducing the object code size.
Consolidate duplicated switch/case blocks for IPV4 and IPV6.
defconfig x86-64 with sfc:
$ size drivers/net/ethernet/sfc/ethtool.o*
text data bss dec hex filename
10055 12 0 10067 2753 drivers/net/ethernet/sfc/ethtool.o.new
10135 12 0 10147 27a3 drivers/net/ethernet/sfc/ethtool.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Per the dt-binding the interrupt is optional so use
platform_get_irq_optional() instead of platform_get_irq(). Since
commit 7723f4c5ecdb ("driver core: platform: Add an error message to
platform_get_irq*()") platform_get_irq() produces an error message
orion-mdio f1072004.mdio: IRQ index 0 not found
which is perfectly normal if one hasn't specified the optional property
in the device tree.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only the bottom 12 bits contain the ATU bin occupancy statistics. The
upper bits need masking off.
Fixes: e0c69ca7dfbb ("net: dsa: mv88e6xxx: Add ATU occupancy via devlink resources")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/ibm/emac/core.c: In function __emac_mdio_write:
drivers/net/ethernet/ibm/emac/core.c:875:9: warning:
variable err set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|