Age | Commit message (Collapse) | Author | Files | Lines |
|
commit 8067302973a1 ("net-next: mediatek: add support for IRQ grouping")
failed to properly update the irq handling inside mtk_poll_controller()
causing compile errors if netconsole was enabled. Fix this by updating
the code to use the new separated irq handler function for RX.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip2me:
To instruct HW to send trapped ip2me traffic to kernel, we have to add
this trap. Selection ip2me traffic is introduced later on in this set.
ARPs:
We are going to stop flooding to CPU port when netdev isn't bridged and
only get packets destined to the netdev's IP address and certain control
packets.
Add traps for ARP request (broadcast) and response (unicast) in order to
get these to the CPU and resolve neighbours.
host miss:
If a packet is routed through a directly connected route and its
destination IP is not in the device's neighbour table, then we need to
trap it to CPU. This will cause the host to resolve the MAC of the
neighbour, which will be eventually programmed to the device's table.
router ingress:
In order to trap packets in router part.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When removing packet traps we should use action 'discard' instead of
'forward', as some trap IDs we'll add cannot be configured with the
later. However, result is the same, as packets are not trapped to the
CPU.
In the future we will be able to reverse the operation properly by
detaching the trap group from the CPU.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the Router Interface Table Register (RITR), which allows us to
create and configure router interfaces (RIFs).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Incoming packets are directed to the router when they match an FDB
entry with action forward to IP router.
Add this action, which was mistakenly named "TRAP".
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When enabling the router in the device we will represent L3 netdevs
using router interfaces (RIFs). These will be specified whenever
programming routes or neighbours on the netdev.
Introduce the basic RIF infrastructure which allows one to lookup a RIF
by its netdev. Later patches in the series will extend this, but the
basic routines are needed now in order to direct traffic to CPU.
Pointers to the RIF structs are stored in an array indexed by the RIF's
number. This will allow us to efficiently update the kernel's neighbour
table when regularly dumping the device's table.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a skeleton router file and do basic HW initialization of router.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During ports initialization a net device is registered for each
available port, which implies the port is usable. However, a port is
only usable after the different parts of the device (e.g. flooding,
buffers) are initialized. This is especially important now, when we must
initialize the router before the ports, as otherwise the device can't be
initialized.
Solve that by initializing the switch ports at the end of init sequence.
Also, remove an unnecessary warning about port up/down events, which
would otherwise be invoked whenever removing the driver, as ports are
removed before unregistering the listener for these events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the Router General Configuration Register (RGCR), which allows us to
enable the router in the device and configure its various parameters.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are going to assign router interfaces (RIFs) to netdevs if an IPv4
address was assigned to them. If one was assigned to a port netdev, this
will translate to the PVID vPort being member in a RIF.
While it's possible for a LAG slave to have an IP address, we can't have
a vPort being member in two FIDs (assuming the LAG device will be
put in bridge / assigned an IP address).
Solve that by making the PVID vPort leave any FID it might be a member
in when joining / leaving LAG.
Note that the PVID vPort is the only vPort that can be present on the
port when it's put under LAG.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When VLAN devices are created on top of LAG, their underlying vPorts are
configured correctly with LAG membership.
However, the PVID vPort is implicit and already present when the port
netdev is put under LAG, so its LAG membership is never set. Set it
correctly when joining / leaving LAG.
This didn't matter until now, but we are going to introduce support for
router interfaces (RIFs), which need to take into account LAG membership.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When port isn't bridged it is still possible to invoke switchdev ops and
configure the device's VLAN filters.
However, this will require us to use different Router InterFaces (RIFs)
for the same netdev, instead of one per-netdev as with any other
configuration.
Taking the above into account and the fact that this functionality is
questionable with regards to the device's normal use-case, remove it and
instead return an error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Port netdevs (e.g. swXpY) that are not bridged are represented in the
device using a vPort with VID=PVID=1 (the PVID vPort), as untagged
packets entering the switch are internally tagged with the PVID VLAN.
When these packets are routed through a different port netdev they
should egress untagged.
This wasn't a problem until now, as non-bridged traffic only originated
from the CPU, which transmits packets out of the port as-is.
When a vPort is created with VID 1 mark it as egress untagged.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The allowable range is 0.25 seconds to 1 second interval. Default is
1 second.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is useful for multi-function devices.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With a default VLAN, the VF has its own VLAN domain and it can receive
all traffic within that domain.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For correctness, the MRU enables bit must be set when passing the
MRU to firmware during vnic configuration.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to the Ethtool FLASHDEV command handler for additional
firmware types to cover all the on-chip processors.
Signed-off-by: Rob Swindell <rob.swindell@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upon successful mgmt processor firmware update, request a self
reset upon next PCIe reset (e.g. system reboot).
Signed-off-by: Rob Swindell <rob.swindell@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To support Secure Firmware Update, we must be able to allocate
a staging area in the Flash. This patch adds support for the
"update" type to tell firmware to do that.
Signed-off-by: Rob Swindell <rob.swindell@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Calling the firmware to do function reset on the PF will kill all the VFs.
To prevent that, we call function reset on the 1st PF open before any VF
can be activated. On subsequent PF opens (with possibly some active VFs),
a bit has been set and we'll skip the function reset. VF driver will
always do function reset on every open. If there is an AER event, we will
always do function reset.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
And update driver version to 1.3.0.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Returning 0 for doing nothing is confusing to the user.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the relevant profile functions to create mlx5e driver instance
serving as VF representor. When SRIOV offloads mode is enabled, each VF
will have a representor netdevice instance on the host.
To do that, we also export set of shared service functions from en_main.c,
such that they can be used by both NIC and repsresentors netdevs.
The newly created representor netdevice has a basic set of net_device_ops
which are the same ndo functions as the NIC netdevice and an ndo of it's
own for phys port name.
The profiling infrastructure allow sharing code between the NIC and the
vport representor even though the representor has only a subset of the
NIC functionality.
The VF reps and the PF which is used in that mode to represent the uplink,
expose switchdev ops. Currently the only op supposed is attr get for the
port parent ID which here serves to identify net-devices belonging to the
same HW E-Switch. Other than that, no offloading is implemented and hence
switching functionality is achieved if one sets SW switching rules, e.g
using tc, bridge or ovs.
Port phys name (ndo_get_phys_port_name) is implemented to allow exporting
to user-space the VF vport number and along with the switchdev port parent
id (phys_switch_id) enable a udev base consistent naming scheme:
SUBSYSTEM=="net", ACTION=="add", ATTR{phys_switch_id}=="<phys_switch_id>", \
ATTR{phys_port_name}!="", NAME="$PF_NIC$attr{phys_port_name}"
where phys_switch_id is exposed by the PF (and VF reps) and $PF_NIC is
the name of the PF netdevice.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce E-Switch registration/unregister representors functions.
Those functions are called by the mlx5e driver when the PF NIC is
created upon pci probe action regardless of the E-Switch mode (NONE,
LEGACY or OFFLOADS).
Adding basic E-Switch database that will hold the vport represntors
upon creation.
This patch doesn't add any new functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To allow support in representor netdevices where we create more than one
netdevice per NIC, add profiles to the mlx5e driver. The profiling
allows for creation of mlx5e instances with different characteristics.
Each profile implements its own behavior using set of function pointers
defined in struct mlx5e_profile. This is done to allow for avoiding complex
per profix branching in the code.
Currently only the profile for the conventional NIC is implemented,
which is of use when a netdev is created upon pci probe.
This patch doesn't add any new functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the current driver implementation two types of receive queue
tables (RQTs) are in use - direct and indirect.
Change the driver to mark each new created RQT (direct or indirect)
as "enabled". This behaviour is needed for introducing new mlx5e
instances which serve to represent SRIOV VFs.
The VF representors will have only one type of RQTs (direct).
An "enabled" flag is added to each RQT to allow better handling
and code sharing between the representors and the nic netdevices.
This patch doesn't add any new functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current refresh tirs self loopback mechanism, refreshes all the tirs
belonging to the same mlx5e instance to prevent self loopback by packets
sent over any ring of that instance. This mechanism relies on all the
tirs/tises of an instance to be created with the same transport domain
number (tdn).
Change the driver to refresh all the tirs created under the same tdn
regardless of which mlx5e netdev instance they belong to.
This behaviour is needed for introducing new mlx5e instances which serve
to represent SRIOV VFs. The representors and the PF share vport used for
E-Switch management, and we want to avoid NIC level HW loopback between
them, e.g when sending broadcast packets. To achieve that, both the
representors and the PF NIC will share the tdn.
This patch doesn't add any new functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To allow creating more than one netdev over the same PCI function, we
change the driver such that global NIC resources are created once and
later be shared amongst all the mlx5e netdevs running over that port.
Move the CQ UAR, PD (pdn), Transport Domain (tdn), MKey resources from
being kept in the mlx5e priv part to a new resources structure
(mlx5e_resources) placed under the mlx5_core device.
This patch doesn't add any new functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement handlers for the devlink commands to get and set the SRIOV
E-Switch mode.
When turning to the switchdev/offloads mode, we disable the e-switch
and enable it again in the new mode, create the NIC offloads table
and create VF reps.
When turning to legacy mode, we remove the VF reps and the offloads
table, and re-initiate the e-switch in it's legacy mode.
The actual creation/removal of the VF reps is done in downstream patches.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The devlink interface is initially used to set/get the mode of the SRIOV e-switch.
Currently, these are only stubs for get/set, down-stream patch will actually
fill them out.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the API to create vport rx rules of the form
packet meta-data :: vport == $VPORT --> $TIR
where the TIR is opened by this VF representor.
This logic will by used for packets that didn't match any rule in the
e-switch datapath and should be received into the host OS through the
netdevice that represents the VF they were sent from.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Belongs to the NIC offloads name-space, and to be used as part of the
SRIOV offloads logic to steer packets that hit the e-switch miss rule
to the TIR of the relevant VF representor.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new namespace (MLX5_FLOW_NAMESPACE_OFFLOADS) to be populated
with flow steering rules that deal with rules that have have to
be executed before the EN NIC steering rules are matched.
The namespace is located after the bypass name-space and before the
kernel name-space. Therefore, it precedes the HW processing done for
rules set for the kernel NIC name-space.
Under SRIOV, it would allow us to match on e-switch missed packet
and forward them to the relevant VF representor TIR.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the API to create send-to-vport e-switch rules of the form
packet meta-data :: send-queue-number == $SQN and source-vport == 0 --> $VPORT
These rules are to be used for a send-to-vport logic which conceptually bypasses
the "normal" steering rules currently present at the e-switch datapath.
Such rule should apply only for packets that originate in the e-switch manager
vport (0) and are sent for a given SQN which is used by a given VF representor
device, and hence the matching logic.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the sriov offloads mode, packets that are not matched by any other
rule should be sent towards the e-switch manager for further processing.
Add such "miss" rule which matches ANY packet as the last rule in the
e-switch FDB and programs the HW to send the packet to vport 0 where
the e-switch manager runs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unlike the legacy mode, here, forwarding rules are not learned by the
driver per events on macs set by VFs/VMs into their vports, but rather
should be programmed by higher-level SW entities.
Saying that, still, in the offloads mode (SRIOV_OFFLOADS), two flow
groups are created by the driver for management (slow path) purposes:
The first group will be used for sending packets over e-switch vports
from the host OS where the e-switch management code runs, to be
received by VFs.
The second group will be used by a miss rule which forwards packets toward
the e-switch manager. Further logic will trap these packets such that
the receiving net-device as seen by the networking stack is the representor
of the vport that sent the packet over the e-switch data-path.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Define three modes for the SRIOV e-switch operation, none (SRIOV_NONE,
none of the VF vports are enabled), legacy (SRIOV_LEGACY, the current mode)
and sriov offloads (SRIOV_OFFLOADS). Currently, when in SRIOV, only the
legacy mode is supported, where steering rules are of the form:
destination mac --> VF vport
This patch does not change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the registers of subctrl may be different, it is better to
mv the registers from hns mdio driver routine to device tree node.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is PORT_TP type if the service port is GE mode. It is wrong to
judge the port type by using if it is service port. Adding the media
type to know port type.
Reported-by: Jinchuan Tian <tianjinchuan1@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sequence of hns_mac_dev_to_enet_if() is the same as
hns_get_enet_interface(), and hns_get_enet_interface() is called
by initialization to get the mac mode. And the mode is not changed
anywhere. Thus add hns_mac_dev_to_enet_if() function to get the mac
mode is obviously redundant.
Reported-by: Jinchuan Tian <tianjinchuan1@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two approaches to assign data, one does 2 loops, another
does 1 loop. This patch normalize the different methods to 1 loop.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In comment line, some time miss a space before */, so this
patch adds a space before */.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the previous review comments from Andy, this patch
deletes the redundant parens in the patch.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the code style in hns driver. Change it from
"buff = buff + xxx" to "buff += xxx". The reveiw comments is
from andy.
Reviewed-by: Andriy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes code sytle of hns driver to make it
simple.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|