summaryrefslogtreecommitdiff
path: root/drivers/phy/microchip
AgeCommit message (Collapse)AuthorFilesLines
2024-01-24phy: lan966x: Add missing serdes mux entryHoratiu Vultur1-0/+2
According to the datasheet(Table 3-2: Port configuration) the serdes 2 (SD2) can be configured to run QSGMII or SGMII mode. Already the QSGMII mode is supported in the serdes_muxes list but was missing the SGMII mode. In this mode the serdes is connected to the port 4. Therefore add this entry in the list. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Link: https://lore.kernel.org/r/20240108205140.1701770-1-horatiu.vultur@microchip.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2023-05-08phy: sparx5-serdes: add skip_cmu_cfg check when configuring lanesDaniel Machon1-0/+5
Add a check for skip_cmu_cfg when configuring the serdes lane. All individual serdeses are reset upon first configuration. Resetting the serdes involves reconfiguring it with preset values. The serdesmode is required to determine the clock-providing CMU, therefore make sure the serdes is not reconfigured if the serdesmode is not set. Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Link: https://lore.kernel.org/r/20230417180335.2787494-8-daniel.machon@microchip.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2023-05-08phy: sparx5-serdes: remove power up of all CMUsDaniel Machon2-26/+0
CMUs should not be powered up by default anymore, so remove responsible code. Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Link: https://lore.kernel.org/r/20230417180335.2787494-7-daniel.machon@microchip.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2023-05-08phy: sparx5-serdes: power on CMUs individuallyDaniel Machon1-1/+42
Power on the CMU instance, that provides the clock for the serdes, given the specified serdes mode and index. The CMU instance is looked up, using a preset map of serdes mode and index to CMU index. Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Link: https://lore.kernel.org/r/20230417180335.2787494-6-daniel.machon@microchip.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2023-05-08phy: sparx5-serdes: power down all CMUs by defaultDaniel Machon1-0/+51
All CMUs are powered up initially. This uses needless power. This patch makes sure all CMUs are powered down by default. This involves configuring a number reference clock and power-down registers of the CMU. Individual CMUs are later powered up, when the serdes lanes are configured. Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Link: https://lore.kernel.org/r/20230417180335.2787494-5-daniel.machon@microchip.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2023-05-08phy: sparx5-serdes: reorder CMU functionsDaniel Machon1-153/+153
Reorder CMU functions, as some of them are now required by the serdes functions. No functional changes. Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Link: https://lore.kernel.org/r/20230417180335.2787494-4-daniel.machon@microchip.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2023-05-08phy: sparx5-serdes: configure optimal quiet mode for serdes lanesDaniel Machon1-1/+31
All the serdes lanes of the sparx5 will transition between normal mode and quiet mode, depending on activity. Make sure that the quiet mode is configured optimally for all lanes initially. Although not much, this will save a small amount of power. Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Link: https://lore.kernel.org/r/20230417180335.2787494-3-daniel.machon@microchip.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2023-05-08phy: sparx5-serdes: add registers required for SD/CMU power downDaniel Machon1-0/+106
Add registers required to configure serdeses and CMUs for initial power down. Signed-off-by: Daniel Machon <daniel.machon@microchip.com> Link: https://lore.kernel.org/r/20230417180335.2787494-2-daniel.machon@microchip.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2022-10-08Merge tag 'phy-for-6.1' of ↵Linus Torvalds2-12/+129
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy Pull phy updates from Vinod Koul: "This contains bunch of new device support and one new Sunplus driver along with updates which include another big round of qmp phy conversion. New support: - Qualcomm SC8280XP eDP & DP and USB3 UNI phy (Bjorn Andersson) - Rockchip rk3568 inno dsidphy (Chris Morgan) - ocelot-serdes phy yaml binding (Colin Foster) - Renesas gen2-usb phy yaml binding (Geert Uytterhoeven) - RGMII suport in lan966x driver (Horatiu Vultur) - Qualcomm SM6375 usb snps-femto-v2 bindings (Konrad Dybcio) - Rockchip rk356x csi-dphya (Michael Riesch) - Qualcomm sdm670 usb2 bindings (Richard Acayan) - Sunplus USB2 PHY (Vincent Shih) Updates: - Mediatek hdmi, ufs, tphy and xsphy updates to use bitfield helpers (Chunfeng Yun) - Continued Qualcomm qmp phy driver split and cleanup. More patches are under review and expected that next cycle might see completion of this activity (Dmitry Baryshkov & Johan Hovold) - TI wiz driver support for j7200 10g (Roger Quadros) - Qualcomm femto phy driver support for override params to help with tuning (Sandeep Maheswaram) - SGMII support in TI wiz driver (Siddharth Vadapalli) - dev_err_probe simplification (Yuan Can)" * tag 'phy-for-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (170 commits) phy: phy-mtk-dp: make array driving_params static const dt-bindings: phy: qcom,qusb2: document sdm670 compatible phy: qcom-qmp-pcie: fix resource mapping for SDM845 QHP PHY phy: rockchip-snps-pcie3: only look for rockchip,pipe-grf on rk3588 phy: tegra: xusb: Enable usb role switch attribute phy: mediatek: fix build warning of FIELD_PREP() phy: qcom-qmp-usb: Use dev_err_probe() to simplify code phy: qcom-qmp-ufs: Use dev_err_probe() to simplify code phy: qcom-qmp-pcie-msm8996: Use dev_err_probe() to simplify code phy: qcom-qmp-combo: Use dev_err_probe() to simplify code phy: qualcomm: call clk_disable_unprepare in the error handling phy: intel: Use dev_err_probe() to simplify code phy: tegra: xusb: Use dev_err_probe() to simplify code phy: qcom-snps: Use dev_err_probe() to simplify code phy: qcom-qusb2: Use dev_err_probe() to simplify code phy: qcom-qmp-pcie: Use dev_err_probe() to simplify code phy: ti: phy-j721e-wiz: fix reference leaks in wiz_probe() phy: mediatek: mipi: remove register access helpers phy: mediatek: mipi: mt8183: use common helper to access registers phy: mediatek: mipi: mt8183: use GENMASK to generate bits mask ...
2022-09-13phy: Add RGMII support on lan966xHoratiu Vultur2-12/+129
The serdes driver contains also a mux to decide which interface type to use. Currently the driver supports GMII/SGMII/QSGMII and partially RGMII. As it doesn't support all the other RGMII interfaces like RGMII_TXID/RXID/ID and it could run only at 1G. Therefore extend this for all the other speeds(10/100) and also allow the other interfaces. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Link: https://lore.kernel.org/r/20220901121455.245103-1-horatiu.vultur@microchip.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2022-08-31phy: lan966x: add support for QUSGMIIMaxime Chevallier1-0/+3
Makes so that the serdes driver also takes QUSGMII in consideration. It's configured exactly as QSGMII as far as the serdes driver is concerned. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-12-14phy: lan966x: Remove set_speed functionHoratiu Vultur1-12/+5
Remove the set_speed function and allow the driver to figure out the speed at which needs to configure the serdes based on the interface type. Fixes: 305524902a0045 ("phy: Add lan966x ethernet serdes PHY driver") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Link: https://lore.kernel.org/r/20211211214717.1284306-1-horatiu.vultur@microchip.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-12-02phy: lan966x: Extend lan966x to support multiple phy interfaces.Horatiu Vultur1-0/+4
Currently the driver is supporting only the interfaces QSGMII, SGMII, RGMII and GMII. This patch extend the supported interfaces with 1000BASE-X and 2500BASE-X. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20211130101015.164916-1-horatiu.vultur@microchip.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-11-23phy: Add lan966x ethernet serdes PHY driverHoratiu Vultur4-0/+766
Add the Microchip lan966x ethernet serdes PHY driver for interfaces available in the lan966x SoC. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Link: https://lore.kernel.org/r/20211116100818.1615762-4-horatiu.vultur@microchip.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-10-26phy: Sparx5 Eth SerDes: Fix return value check in sparx5_serdes_probe()Yang Yingliang1-2/+2
In case of error, the function devm_ioremap() returns NULL pointer not ERR_PTR(). The IS_ERR() test in the return value check should be replaced with NULL test. Fixes: 2ff8a1eeb5aa ("phy: Add Sparx5 ethernet serdes PHY driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20210909072149.2934047-1-yangyingliang@huawei.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-06-03phy: Sparx5 Eth SerDes: check return value after calling platform_get_resource()Yang Yingliang1-0/+4
It will cause null-ptr-deref if platform_get_resource() returns NULL, we need check the return value. Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20210603051014.2674744-1-yangyingliang@huawei.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-04-06phy: fix resource_size.cocci warningskernel test robot1-1/+1
drivers/phy/microchip/sparx5_serdes.c:2440:54-57: ERROR: Missing resource_size with iores Use resource_size function on resource object instead of explicit computation. Generated by: scripts/coccinelle/api/resource_size.cocci Fixes: 2ff8a1eeb5aa ("phy: Add Sparx5 ethernet serdes PHY driver") CC: Steen Hegelund <steen.hegelund@microchip.com> Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/r/20210318232844.GA65886@63b0c5462fda Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-04-06phy: Sparx5 Eth SerDes: Use direct register operationsSteen Hegelund1-918/+951
Use direct register operations instead of a table of register information to lower the stack usage. Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com> Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/r/20210329141309.612459-2-steen.hegelund@microchip.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-03-31phy: microchip: PHY_SPARX5_SERDES should depend on ARCH_SPARX5Geert Uytterhoeven1-0/+1
The Microchip Sparx5 SerDes PHY is present only Microchip Sparx5 SoCs. Hence add a dependency on ARCH_SPARX5, to prevent asking the user about this driver when configuring a kernel without support for Sparx5 SoCs. Fixes: 2ff8a1eeb5aa8bb4 ("phy: Add Sparx5 ethernet serdes PHY driver") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20210331081937.367408-1-geert+renesas@glider.be Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-03-17phy: Add Sparx5 ethernet serdes PHY driverSteen Hegelund5-0/+5329
Add the Microchip Sparx5 ethernet serdes PHY driver for the 6G, 10G and 25G interfaces available in the Sparx5 SoC. Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com> Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20210218161451.3489955-4-steen.hegelund@microchip.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
generated by cgit v1.2.3 (git 2.39.0) at 2024-07-28 15:25:04 +0300