| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
For MIPI-CSI sender use-case it is common to specify the allowed
link-frequencies which should be used for the MIPI link and is
half the hs-clock rate.
This commit adds a helper to calculate the D-PHY timing based on the
hs-clock rate so we don't need to calculate the timings within the
driver.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Factor out the calculation into phy_mipi_dphy_calc_config(). This is
needed for the follow up patch which adds the support to calculate the
timings based on a given hs clock. No functional changes are done.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
According to the comment of the function phy_mipi_dphy_get_default_config(),
it uses minimum D-PHY timings based on MIPI D-PHY specification. They are
derived from the valid ranges specified in Section 6.9, Table 14, Page 41
of the D-PHY specification (v1.2). The table 14 explicitly mentions that
the minimum T-LPX parameter is 50 nanoseconds and the minimum TA-SURE
parameter is T-LPX nanoseconds. Likewise, the kernel doc of the 'lpx' and
'ta_sure' members of struct phy_configure_opts_mipi_dphy mentions that
the minimum values are 50000 picoseconds and @lpx picoseconds respectively.
Also, the function phy_mipi_dphy_config_validate() checks if cfg->lpx is
less than 50000 picoseconds and if cfg->ta_sure is less than cfg->lpx,
which hints the same minimum values.
Without this patch, the function phy_mipi_dphy_get_default_config()
wrongly sets cfg->lpx to 60000 picoseconds and cfg->ta_sure to 2 * cfg->lpx.
So, let's correct them to 50000 picoseconds and cfg->lpx respectively.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: dddc97e82303 ("phy: dphy: Add configuration helpers")
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220216071257.1647703-1-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The D-PHY specification (v1.2) explicitly mentions that the T-CLK-PRE
parameter's unit is Unit Interval(UI) and the minimum value is 8. Also,
kernel doc of the 'clk_pre' member of struct phy_configure_opts_mipi_dphy
mentions that it should be in UI. However, the dphy core driver wrongly
sets 'clk_pre' to 8000, which seems to hint that it's in picoseconds.
So, let's fix the dphy core driver to correctly reflect the T-CLK-PRE
parameter's minimum value according to the D-PHY specification.
I'm assuming that all impacted custom drivers shall program values in
TxByteClkHS cycles into hardware for the T-CLK-PRE parameter. The D-PHY
specification mentions that the frequency of TxByteClkHS is exactly 1/8
the High-Speed(HS) bit rate(each HS bit consumes one UI). So, relevant
custom driver code is changed to program those values as
DIV_ROUND_UP(cfg->clk_pre, BITS_PER_BYTE), then.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: 2ed869990e14 ("phy: Add MIPI D-PHY configuration options")
Tested-by: Liu Ying <victor.liu@nxp.com> # RM67191 DSI panel on i.MX8mq EVK
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Guido Günther <agx@sigxcpu.org> # Librem 5 (imx8mq) with it's rather picky panel
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220124024007.1465018-1-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The rest of the code refers to version 1.2 of the MIPI D-PHY
specification. But this comment refers to 2.1, while a sub comment of
the function refers to 1.2 again. Replace 2.1 with 1.2.
Signed-off-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Link: https://lore.kernel.org/r/20210421041740.8451-1-sebastian.fricke@posteo.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
We have currently three users of the PSEC_PER_SEC each of them defining it
individually. Instead, move it to time64.h to be available for everyone.
There is a new user coming with the same constant in use. It will also
make its life easier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Init and wakeup D-PHY parameters are in the micro/milliseconds range,
putting the values real close to the types limits if they were in
picoseconds.
Move them to microseconds which should be better fit.
Suggested-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The MIPI D-PHY spec defines default values and boundaries for most of the
parameters it defines. Introduce helpers to help drivers get meaningful
values based on their current parameters, and validate the boundaries of
these parameters if needed.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
