Age | Commit message (Collapse) | Author | Files | Lines |
|
All of the remaining callers of thermal_zone_device_register()
can use thermal_tripless_zone_device_register(), so make them
do so in order to allow the former to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The INHIBIT_CHARGE status bit means the battery has reached a
pre-programmed charge limit which is some voltage offset below the
target float voltage. This should be reported as a STATUS_FULL rather
than UNKNOWN, fix it.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Link: https://lore.kernel.org/r/20230802-pmi8998-charger-fixes-v1-2-a8f1e8b84c1e@linaro.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
These property were intended to allow the power supply to be treated as a
cooling device, however the cooling device interface has been dropped
from the psy core code. They now just duplicate the CURRENT_NOW and
CURRENT_MAX properties and are generally confusing, drop them.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Link: https://lore.kernel.org/r/20230802-pmi8998-charger-fixes-v1-1-a8f1e8b84c1e@linaro.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
smatch warnings:
drivers/power/supply/qcom_pmi8998_charger.c:565 smb2_status_change_work() error: uninitialized symbol 'usb_online'.
usb_online is used uninitialized whenever smb2_get_prop_usb_online()
returns a negative value.
Thus, fix the issue by initializing usb_online to 0.
Fixes: 8648aeb5d7b7 ("power: supply: add Qualcomm PMI8998 SMB2 Charger driver")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/r/202307280638.556PrzIS-lkp@intel.com/
Signed-off-by: Yu Liao <liaoyu15@huawei.com>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org
Link: https://lore.kernel.org/r/20230802023130.2516232-1-liaoyu15@huawei.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
When the power supply device being registered supports a temperature
readout, the core registers a thermal zone for it. The thermal core
would register a hwmon device for that unless told otherwise.
When CONFIG_POWER_SUPPLY_HWMON is enabled, the power supply core creates
a hwmon device. This results in a second entry, one which has a better
name than the one registered through the thermal framework. It could
potentially have readouts other than temperature.
To simplify the result, tell the thermal framework to not register a
hwmon device if CONFIG_POWER_SUPPLY_HWMON is enabled. The result is
one hwmon device with all the readings the device supports.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Don't populate the read-only array on the stack, instead make it
static const.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Adds a check of the FORCE_20PCT bit when getting the precharge
current value.
According to the bit description for the FORCE_20PCT bit, when
FORCE_20PCT is true, the precharge current target is 50% of
what is configured in the IPRECHG bit field.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Reviewed-by: David Rhodes <drhodes@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: David Lechner <david@lechnology.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- Add new Qualcomm PMI8998/PM660 SMB2 charger
- bq256xx: support systems without thermistors
- cros_pchg: fix peripheral device status after system resume
- axp20x_usb_power: add support for AXP192
- qcom-pon: add support for pm8941
- at91-reset: prepare to expose reset reason to sysfs
- switch all I2C drivers back to use .probe instead of .probe_new
- convert some more DT bindings to YAML
- misc cleanups
* tag 'for-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (28 commits)
MAINTAINERS: add documentation file for Microchip SAMA5D2 shutdown controller
dt-bindings: power: reset: atmel,sama5d2-shdwc: convert to yaml
dt-bindings: power: reset: atmel,at91sam9260-shdwc: convert to yaml
power: reset: at91-reset: change the power on reason prototype
power: reset: qcom-pon: add support for pm8941-pon
dt-bindings: power: reset: qcom-pon: define pm8941-pon
power: supply: add Qualcomm PMI8998 SMB2 Charger driver
dt-bindings: power: supply: qcom,pmi8998-charger: add bindings for smb2 driver
power: supply: rt9467: Make charger-enable control as logic level
power: supply: Switch i2c drivers back to use .probe()
power: reset: add HAS_IOPORT dependencies
dt-bindings: power: supply: axp20x: Add AXP192 compatible
power: supply: axp20x_usb_power: Add support for AXP192
power: supply: axp20x_usb_power: Remove variant IDs from VBUS polling check
power: supply: axp20x_usb_power: Use regmap field for VBUS disabling
power: supply: axp20x_usb_power: Use regmap fields for USB BC feature
power: supply: axp20x_usb_power: Use regmap fields for VBUS monitor feature
power: supply: axp20x_usb_power: Simplify USB current limit handling
power: supply: hwmon: constify pointers to hwmon_channel_info
power: supply: twl4030_madc_battery: Refactor twl4030_madc_bat_ext_changed()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"New Drivers:
- Add support for Intel Cherry Trail Whiskey Cove PMIC LEDs
- Add support for Awinic AW20036/AW20054/AW20072 LEDs
New Device Support:
- Add support for PMI632 LPG to QCom LPG
- Add support for PMI8998 to QCom Flash
- Add support for MT6331, WLEDs and MT6332 to Mediatek MT6323 PMIC
New Functionality:
- Implement the LP55xx Charge Pump
- Add support for suspend / resume to Intel Cherry Trail Whiskey Cove PMIC
- Add support for breathing mode to Intel Cherry Trail Whiskey Cove PMIC
- Enable per-pin resolution Pinctrl in LEDs GPIO
Fix-ups:
- Allow thread to sleep by switching from spinlock to mutex
- Add lots of Device Tree bindings / support
- Adapt relationships / dependencies driven by Kconfig
- Switch I2C drivers from .probe_new() to .probe()
- Remove superfluous / duplicate code
- Replace strlcpy() with strscpy() for efficiency and overflow prevention
- Staticify various functions
- Trivial: Fixing coding style
- Simplify / reduce code
Bug Fixes:
- Prevent NETDEV_LED_MODE_LINKUP from being cleared on rename
- Repair race between led_set_brightness(LED_{OFF,FULL})
- Fix Oops relating to sleeping in critical sections
- Clear LED_INIT_DEFAULT_TRIGGER flag when clearing the current trigger
- Do not leak resources in error handling paths
- Fix unsigned comparison which can never be negative
- Provide missing NULL terminating entries in tables
- Fix misnaming issues"
* tag 'leds-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (53 commits)
leds: leds-mt6323: Adjust return/parameter types in wled get/set callbacks
leds: sgm3140: Add richtek,rt5033-led compatible
dt-bindings: leds: sgm3140: Document richtek,rt5033 compatible
dt-bindings: backlight: kinetic,ktz8866: Add missing type for "current-num-sinks"
dt-bindings: leds: Drop unneeded quotes
leds: Fix config reference for AW200xx driver
leds: leds-mt6323: Add support for WLEDs and MT6332
leds: leds-mt6323: Add support for MT6331 leds
leds: leds-mt6323: Open code and drop MT6323_CAL_HW_DUTY macro
leds: leds-mt6323: Drop MT6323_ prefix from macros and defines
leds: leds-mt6323: Specify registers and specs in platform data
dt-bindings: leds: leds-mt6323: Document mt6332 compatible
dt-bindings: leds: leds-mt6323: Document mt6331 compatible
leds: simatic-ipc-leds-gpio: Introduce more Kconfig switches
leds: simatic-ipc-leds-gpio: Split up into multiple drivers
leds: simatic-ipc-leds-gpio: Move two extra gpio pins into another table
leds: simatic-ipc-leds-gpio: Add terminating entries to gpio tables
leds: flash: leds-qcom-flash: Fix an unsigned comparison which can never be negative
leds: cht-wcove: Remove unneeded semicolon
leds: cht-wcove: Fix an unsigned comparison which can never be negative
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for TI TPS6594/TPS6593/LP8764 PMICs
- Add support for Samsung RT5033 Battery Charger
- Add support for Analog Devices MAX77540 and MAX77541 PMICs
New Device Support:
- Add support for SPI to Rockchip RK808 (and friends)
- Add support for AXP192 PMIC to X-Powers AXP20X
- Add support for AXP313a PMIC to X-Powers AXP20X
- Add support for RK806 to Rockchip RK8XX
Removed Device Support:
- Removed MFD support for Richtek RT5033 Battery
Fix-ups:
- Remove superfluous code
- Switch I2C drivers from .probe_new() to .probe()
- Convert over to managed resources (devm_*(), etc)
- Use dev_err_probe() for returning errors from .probe()
- Add lots of Device Tree bindings / support
- Improve cache efficiency by switching to Maple
- Use own exported namespaces (NS)
- Include missing and remove superfluous headers
- Start using / convert to the new shutdown sys-off API
- Trivial: variable / define renaming
- Make use of of_property_read_reg() when requesting DT 'reg's
Bug Fixes:
- Fix chip revision readout due to incorrect data masking
- Amend incorrect register and mask values used for charger state
- Hide unused functionality at compile time
- Fix resource leaks following error handling routines
- Return correct error values and fix error handling in general
- Repair incorrect device names - used for device matching
- Remedy broken module auto-loading"
* tag 'mfd-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (51 commits)
dt-bindings: mfd: max77541: Add ADI MAX77541/MAX77540
iio: adc: max77541: Add ADI MAX77541 ADC Support
regulator: max77541: Add ADI MAX77541/MAX77540 Regulator Support
dt-bindings: regulator: max77541: Add ADI MAX77541/MAX77540 Regulator
mfd: Switch two more drivers back to use struct i2c_driver::probe
dt-bindings: mfd: samsung,s5m8767: Simplify excluding properties
mfd: stmpe: Only disable the regulators if they are enabled
mfd: max77541: Add ADI MAX77541/MAX77540 PMIC Support
dt-bindings: mfd: gateworks-gsc: Remove unnecessary fan-controller nodes
mfd: core: Use of_property_read_reg() to parse "reg"
mfd: stmfx: Nullify stmfx->vdd in case of error
mfd: stmfx: Fix error path in stmfx_chip_init
mfd: intel-lpss: Add missing check for platform_get_resource
mfd: stpmic1: Add PMIC poweroff via sys-off handler
mfd: stpmic1: Fixup main control register and bits naming
dt-bindings: mfd: qcom,tcsr: Add the compatible for IPQ8074
mfd: tps65219: Add support for soft shutdown via sys-off API
mfd: pm8008: Drop bogus i2c module alias
mfd: pm8008: Fix module autoloading
mfd: tps65219: Add GPIO cell instance
...
|
|
'ib-mfd-tps6594-core-6.5', 'ib-mfd-regulator-max5970-6.5', 'ib-mfd-regulator-6.5' and 'ib-mfd-power-6.5' into ibs-for-mfd-merged
|
|
Add a driver for the SMB2 charger block found in the Qualcomm PMI8998
and PM660.
This driver is capable of utilising Qualcomm's Automatic Power Source
Detection (APSD) BC1.2 implementation, as well as Automatic Input
Current Limiting (AICL) to configure the maximum input current
limit of DCP (wall) chargers.
Quick Charge is not currently supported.
Most devices using the smb2 charger have a secondary dedicated charger
chip which is used in parallel to enable faster charger without
overheating. However, not all do, as a result to ensure safety until
these are supported, the maximum current is limited to ~1A via the
FAST_CHARGE_CURRENT_CFG register.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: Joel Selvaraj <joelselvaraj.oss@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The rt5033-battery fuelgauge can't get a status by itself. The rt5033-charger
can, let's get this value.
To get the charger as a "supplier" from the devicetree, the "of_node" needs
to be initiated.
Additionally, in the probe function replace dev_err() with dev_err_probe(),
this will avoid printing an error for -EPROBE_DEFER when the battery driver
probes before the charger driver.
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/a2015d257b145108a3ecdf107a3040362c887fc5.1684182964.git.jahau@rocketmail.com
|
|
Move struct rt5033_battery from the mfd header into the battery driver because
it's not used by others.
Within struct rt5033_battery, remove the line "struct rt5033_dev *rt5033;"
because it doesn't get used.
In rt5033.h, remove #include <linux/power_supply.h>, it's not necessary
anymore.
In rt5033_battery.c, remove #include <linux/mfd/rt5033.h>, it's not necessary
anymore either. Instead add #include <linux/regmap.h> and
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/736e1cbee257853cb3d1da6f05c184e9a053263b.1684182964.git.jahau@rocketmail.com
|
|
This patch adds device driver of Richtek RT5033 PMIC. The driver supports
switching charger. rt5033 charger provides three charging modes. The charging
modes are pre-charge mode, fast charge mode and constant voltage mode. They
vary in charge rate, the charge parameters can be controlled by i2c interface.
Tested-by: Raymond Hackley <raymondhackley@protonmail.com>
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/9556d4ebb30fd321e37aa0eb343554122e4720c9.1684182964.git.jahau@rocketmail.com
|
|
The current coding make 'charger-enable-gpio' control as real hardware
level. This conflicts with the default binding example. For driver
behavior, no need to use real hardware level, just logic level is
enough. This change can make this flexibility keep in dts gpio active
level about this pin.
Fixes: 6f7f70e3a8dd ("power: supply: rt9467: Add Richtek RT9467 charger driver")
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Merge series from Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>:
A "known issue" during implementation of SE DMA for spi geni driver was
that it does DMA map/unmap internally instead of in spi framework.
Current patches remove this hiccup and also clean up code a bit.
Testing revealed no regressions and results with 1000 iterations of
reading from EC showed no loss of performance.
Results
=======
Before - Iteration 999, min=5.10, max=5.17, avg=5.14, ints=25129
After - Iteration 999, min=5.10, max=5.20, avg=5.15, ints=25153
|
|
After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
led_blink_set[_oneshot]()'s delay_on and delay_off function parameters
are pass by reference, so that hw-blink implementations can report
back the actual achieved delays when the values have been rounded
to something the hw supports.
This is really only interesting for the sysfs API / the timer trigger.
Other triggers don't really care about this and none of the callers of
led_trigger_blink[_oneshot]() do anything with the returned delay values.
Change the led_trigger_blink[_oneshot]() delay parameters to pass-by-value,
there are 2 reasons for this:
1. led_cdev->blink_set() may sleep, while led_trigger_blink() may not.
So on hw where led_cdev->blink_set() sleeps the call needs to be deferred
to a workqueue, in which case the actual achieved delays are unknown
(this is a preparation patch for the deferring).
2. Since the callers don't care about the actual achieved delays, allowing
callers to directly pass a value leads to simpler code for most callers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20230510162234.291439-2-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The logic used for power_supply_is_system_supplied() counts all power
supplies and assumes that the system is running from AC if there is
either a non-battery power-supply reporting to be online or if no
power-supplies exist at all.
The second rule is for desktop systems, that don't have any
battery/charger devices. These systems will incorrectly report to be
powered from battery once a device scope power-supply is registered
(e.g. a HID device), since these power-supplies increase the counter.
Apart from HID devices, recent dGPUs provide UCSI power supplies on a
desktop systems. The dGPU by default doesn't have anything plugged in so
it's 'offline'. This makes power_supply_is_system_supplied() return 0
with a count of 1 meaning all drivers that use this get a wrong judgement.
To fix this case adjust the logic to also examine the scope of the power
supply. If the power supply is deemed a device power supply, then don't
count it.
Cc: Evan Quan <Evan.Quan@amd.com>
Suggested-by: Lijo Lazar <Lijo.Lazar@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
mt6360_charger_probe
devm_work_autocancel may fail, add a check and return early.
Fixes: 0402e8ebb8b86 ("power: supply: mt6360_charger: add MT6360 charger support")
Signed-off-by: Kang Chen <void0red@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
CHARGE_INHIBITED bit position of the ChargerStatus register is actually
0 not 1. This patch corrects it.
Fixes: feb583e37f8a8 ("power: supply: add sbs-charger driver")
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add support for the AXP192. It is most similar to the AXP202 but
the current limits are different and the USB OTG status register
has a different address (0x04 instead of 0x02).
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Use an explicit boolean flag instead of a check based on the
variant ID. Since this is the last use of variant IDs in the
driver, also remove the IDs.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The POWER_SUPPLY_PROP_ONLINE property allows controlling the VBUS
enable state on supported PMICs. Switch to regmap fields to reduce
dependence on variant IDs.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Replace the use of variant IDs with a regmap field, to reduce
dependence on variant IDs.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Use regmap fields to describe the VBUS valid bit and VBUS monitor
enable bit. This allows the driver to easily support other chips,
eg. the AXP192, that have the VBUS valid bit in a different register.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Handle the USB current limit with a lookup table and regmap field,
which minimizes code duplication. Invalid or unlimited values are
denoted by -1 entries, and can't be selected from userspace.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Split rk808 into a core and an i2c part in preparation for
SPI support.
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> # for RTC
Tested-by: Diederik de Haas <didi.debian@cknow.org> # Rock64, Quartz64 Model A + B
Tested-by: Vincent Legoll <vincent.legoll@gmail.com> # Pine64 QuartzPro64
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230504173618.142075-6-sebastian.reichel@collabora.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Fix passing zero to 'dev_err_probe()' in 'rt9467_request_interrupt()'
Fixes: 6f7f70e3a8dd ("power: supply: rt9467: Add Richtek RT9467 charger driver")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/202305111228.bHLWU6bq-lkp@intel.com/
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Reduce the amount of output this dev_dbg() statement emits into logs,
otherwise if system software polls the sysfs entry for data and keeps
getting -ENODATA, it could end up filling the logs up.
This does in fact make systemd journald choke, since during boot the
sysfs power supply entries are polled and if journald starts at the
same time, the journal is just being repeatedly filled up, and the
system stops on trying to start journald without booting any further.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
After commit 27a2195efa8d26447c ("power: supply: core: auto-exposure
of simple-battery data") we call power_supply_get_battery_info() in
__power_supply_register(), but it causes test_battery crash with NULL
pointer:
[ 7.524846] __power_supply_register: Expected proper parent device for 'test_battery'
[ 7.524856] CPU 3 Unable to handle kernel paging request at virtual address 0000000000000278, era == 9000000002fb279c, ra == 9000000003173434
[ 7.524862] Oops[#1]:
[ 7.524866] CPU: 3 PID: 1 Comm: swapper/0 Not tainted 6.3.0+ #524
[ 7.524870] Hardware name: Loongson Loongson-3A5000-7A1000-1w-CRB/Loongson-LS3A5000-7A1000-1w-CRB, BIOS vUDK2018-LoongArch-V2.0.0-prebeta9 10/21/2022
[ 7.524872] pc 9000000002fb279c ra 9000000003173434 tp 90000001001f0000 sp 90000001001f3c00
[ 7.524875] a0 0000000000000000 a1 0000000000000000 a2 0000000000000000 a3 9000000004553e13
[ 7.524878] a4 9000000004553e16 a5 ffffffffffffffff a6 9000000003fd0948 a7 0000000000000030
[ 7.524881] t0 9000000003173434 t1 90000000035e2c00 t2 0000000000000001 t3 00000000fffff2b0
[ 7.524883] t4 0000000000000007 t5 fffffffffffffffe t6 0000000000000000 t7 0000000000000010
[ 7.524886] t8 00000000000000b4 u0 00000001c0840c76 s9 0000000000000000 s0 0000000000000000
[ 7.524889] s1 900000000370c458 s2 0000000000000001 s3 9000000101f81000 s4 9000000101f81038
[ 7.524891] s5 9000000101f813a0 s6 900000000370c398 s7 9000000003eebd18 s8 90000000037c0070
[ 7.524894] ra: 9000000003173434 power_supply_get_battery_info+0xe4/0x710
[ 7.591224] ERA: 9000000002fb279c __dev_fwnode+0x8/0x20
[ 7.853583] CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE)
[ 7.859740] PRMD: 00000004 (PPLV0 +PIE -PWE)
[ 7.864073] EUEN: 00000000 (-FPE -SXE -ASXE -BTE)
[ 7.868839] ECFG: 00071c1c (LIE=2-4,10-12 VS=7)
[ 7.873430] ESTAT: 00010000 [PIL] (IS= ECode=1 EsubCode=0)
[ 7.878884] BADV: 0000000000000278
[ 7.882346] PRID: 0014c010 (Loongson-64bit, Loongson-3A5000)
[ 7.888056] Modules linked in:
[ 7.891088] Process swapper/0 (pid: 1, threadinfo=0000000091357ee8, task=00000000313d98cb)
[ 7.899307] Stack : 00000000000000b4 900000000279aca8 0000000000000001 0000000000000000
[ 7.907274] 0000000000000049 0000000000000408 9000000100008c00 90000000035b6370
[ 7.915238] 900000000b801080 90000000029a440c 9000000003eb4680 9000000003eb4680
[ 7.923202] 9000000101f81038 900000000357cdcc 0000000000000001 900000000370c458
[ 7.931166] 9000000101f81000 90000000037c0070 9000000003eebd18 900000000370c398
[ 7.939131] 90000000045f4530 9000000101f81038 0000000000000000 0000000000000001
[ 7.947095] 900000000370c458 9000000101f81000 0000000000000000 9000000003173e64
[ 7.955059] 0000000000000026 9000000003de3880 9000000100562040 900000000357e07c
[ 7.963023] 000000000000026f 0000000000000001 90000001001f3d68 fffffffffffffff5
[ 7.970987] 90000000036d2ca8 90000000027429d8 90000000037c0030 0000000000000001
[ 7.978951] ...
[ 7.981379] Call Trace:
[ 7.981382] [<9000000002fb279c>] __dev_fwnode+0x8/0x20
[ 7.988916] [<9000000003173434>] power_supply_get_battery_info+0xe4/0x710
[ 7.995666] [<9000000003173e64>] __power_supply_register+0x404/0x580
[ 8.001984] [<900000000379d368>] test_power_init+0x6c/0x124
[ 8.007527] [<90000000026e08f8>] do_one_initcall+0x58/0x1ec
[ 8.013066] [<9000000003761614>] kernel_init_freeable+0x290/0x310
[ 8.019127] [<90000000035b40e8>] kernel_init+0x24/0x11c
[ 8.024324] [<90000000026e2048>] ret_from_kernel_thread+0xc/0xa4
[ 8.030295]
[ 8.031769] Code: 4c000020 0015002c 03400000 <28c9e08c> 40000d80 02c06184 4c000020 28ca0084 4c000020
Root cause: psy->dev.parent is NULL in power_supply_get_battery_info(),
so change the else branch to be 'else if (psy->dev.parent)' and return
-ENOENT if psy->dev.parent is NULL.
Fixes: 27a2195efa8d26447c ("power: supply: core: auto-exposure of simple-battery data")
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The bq24192 model relies on external charger-type detection and once
that is done the bq24190_charger code will update the input current.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current. This allows the fuel-gauge driver to timely recheck
if the battery is charging after the new input current has been applied
and then it can immediately notify userspace about this.
Fixes: 18f8e6f695ac ("power: supply: bq24190_charger: Get input_current_limit from our supplier")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
current or voltage
The bq25892 model relies on external charger-type detection and once
that is done the bq25890_charger code will update the input current
and if pumpexpress is used also the input voltage.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current or voltage. This allows the fuel-gauge driver
to timely recheck if the battery is charging after the new input
settings have been applied and then it can immediately notify
userspace about this.
Fixes: 48f45b094dbb ("power: supply: bq25890: Support higher charging voltages through Pump Express+ protocol")
Fixes: eab25b4f93aa ("power: supply: bq25890: On the bq25892 set the IINLIM based on external charger detection")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Use mod_delayed_work() instead of separate cancel_delayed_work_sync() +
schedule_delayed_work() calls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
stabilize
bq27xxx_external_power_changed() gets called when the charger is plugged
in or out. Rather then immediately scheduling an update wait 0.5 seconds
for things to stabilize, so that e.g. the (dis)charge current is stable
when bq27xxx_battery_update() runs.
Fixes: 740b755a3b34 ("bq27x00: Poll battery state")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
sign changes
On gauges where the current register is signed, there is no charging
flag in the flags register. So only checking flags will not result
in power_supply_changed() getting called when e.g. a charger is plugged
in and the current sign changes from negative (discharging) to
positive (charging).
This causes userspace's notion of the status to lag until userspace
does a poll.
And when a power_supply_leds.c LED trigger is used to indicate charging
status with a LED, this LED will lag until the capacity percentage
changes, which may take many minutes (because the LED trigger only is
updated on power_supply_changed() calls).
Fix this by calling bq27xxx_battery_current_and_status() on gauges with
a signed current register and checking if the status has changed.
Fixes: 297a533b3e62 ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Move the bq27xxx_battery_update() functions to below
the bq27xxx_battery_current_and_status() function.
This is just moving a block of text, no functional changes.
This is a preparation patch for making bq27xxx_battery_update() check
the status and have it call power_supply_changed() on status changes.
Fixes: 297a533b3e62 ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
bq27xxx_battery_current_and_status()
Add a cache parameter to bq27xxx_battery_current_and_status() so that
it can optionally use cached flags instead of re-reading them itself.
This is a preparation patch for making bq27xxx_battery_update() check
the status and have it call power_supply_changed() on status changes.
Fixes: 297a533b3e62 ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.
There are 2 problems with this:
1. If the driver is unbound through sysfs, rather then the module being
rmmod-ed, this changes poll_interval unexpectedly
2. This is racy, after it being set poll_interval could be changed
before bq27xxx_battery_update() checks it through
/sys/module/bq27xxx_battery/parameters/poll_interval
Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.
There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.
Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item.
Fixes: 8cfaaa811894 ("bq27x00_battery: Fix OOPS caused by unregistring bq27x00 driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
devm_request_threaded_irq() requested IRQs are only free-ed after
the driver's remove function has ran. So the IRQ could trigger and
call bq27xxx_battery_update() after bq27xxx_battery_teardown() has
already run.
Switch to explicitly free-ing the IRQ in bq27xxx_battery_i2c_remove()
to fix this.
Fixes: 8807feb91b76 ("power: bq27xxx_battery: Add interrupt handling support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
bq27xxx_battery_update() assumes / requires that it is only run once,
not multiple times at the same time. But there are 3 possible callers:
1. bq27xxx_battery_poll() delayed_work item handler
2. bq27xxx_battery_irq_handler_thread() I2C IRQ handler
3. bq27xxx_battery_setup()
And there is no protection against these racing with each other,
fix this race condition by making all callers take di->lock:
- Rename bq27xxx_battery_update() to bq27xxx_battery_update_unlocked()
- Add new bq27xxx_battery_update() which takes di->lock and then calls
bq27xxx_battery_update_unlocked()
- Make stale cache check code in bq27xxx_battery_get_property(), which
already takes di->lock directly to check the jiffies, call
bq27xxx_battery_update_unlocked() instead of messing with
the delayed_work item
- Make bq27xxx_battery_update_unlocked() mod the delayed-work item
so that the next poll is delayed to poll_interval milliseconds after
the last update independent of the source of the update
Fixes: 740b755a3b34 ("bq27x00: Poll battery state")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
When a battery's status changes from charging to full then
the charging-blink-full-solid trigger tries to change
the LED from blinking to solid/on.
As is documented in include/linux/leds.h to deactivate blinking /
to make the LED solid a LED_OFF must be send:
"""
* Deactivate blinking again when the brightness is set to LED_OFF
* via the brightness_set() callback.
"""
led_set_brighness() calls with a brightness value other then 0 / LED_OFF
merely change the brightness of the LED in its on state while it is
blinking.
So power_supply_update_bat_leds() must first send a LED_OFF event
before the LED_FULL to disable blinking.
Fixes: 6501f728c56f ("power_supply: Add new LED trigger charging-blink-solid-full")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
twl4030_madc_bat_ext_changed() is a wrapper around
"power_supply_changed(psy);" and it has the same prototype.
Remove it, replacing it with making the external_power_changed
callback directly point to power_supply_changed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
max17042_external_power_changed() is a wrapper around
"power_supply_changed(psy);" and it has the same prototype.
Remove it, replacing it with making the external_power_changed
callback directly point to power_supply_changed.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Purism Kernel Team <kernel@puri.sm>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
sc27xx_fgu_external_power_changed() dereferences data->battery,
which gets sets in ab8500_btemp_probe() like this:
data->battery = devm_power_supply_register(dev, &sc27xx_fgu_desc,
&fgu_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where sc27xx_fgu_external_power_changed() may get called while
data->battery has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in data->battery,
so sc27xx_fgu_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
After this change sc27xx_fgu_external_power_changed() is reduced to just
"power_supply_changed(psy);" and it has the same prototype. While at it
simply replace it with making the external_power_changed callback
directly point to power_supply_changed.
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
bq25890_charger_external_power_changed() dereferences bq->charger,
which gets sets in bq25890_power_supply_init() like this:
bq->charger = devm_power_supply_register(bq->dev, &bq->desc, &psy_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where bq25890_charger_external_power_changed() may get called while
bq->charger has not been set yet leading to a NULL pointer dereference.
This race hits during boot sometimes on a Lenovo Yoga Book 1 yb1-x90f
when the cht_wcove_pwrsrc (extcon) power_supply is done with detecting
the connected charger-type which happens to exactly hit the small window:
BUG: kernel NULL pointer dereference, address: 0000000000000018
<snip>
RIP: 0010:__power_supply_is_supplied_by+0xb/0xb0
<snip>
Call Trace:
<TASK>
__power_supply_get_supplier_property+0x19/0x50
class_for_each_device+0xb1/0xe0
power_supply_get_property_from_supplier+0x2e/0x50
bq25890_charger_external_power_changed+0x38/0x1b0 [bq25890_charger]
__power_supply_changed_work+0x30/0x40
class_for_each_device+0xb1/0xe0
power_supply_changed_work+0x5f/0xe0
<snip>
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in bq->charger,
so bq25890_charger_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
Fixes: eab25b4f93aa ("power: supply: bq25890: On the bq25892 set the IINLIM based on external charger detection")
Cc: stable@vger.kernel.org
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
fuel_gauge_external_power_changed() dereferences info->bat,
which gets sets in axp288_fuel_gauge_probe() like this:
info->bat = devm_power_supply_register(dev, &fuel_gauge_desc, &psy_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where fuel_gauge_external_power_changed() may get called while
info->bat has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in info->bat,
so fuel_gauge_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
Fixes: 30abb3d07929 ("power: supply: axp288_fuel_gauge: Take lock before updating the valid flag")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|