Age | Commit message (Collapse) | Author | Files | Lines |
|
Currently the struct "rt5033_charger_data" is initialized rather complicated.
The cause lies inside of the struct "rt5033_charger", where struct
"rt5033_charger_data" is implemented as a pointer *chg.
Therefore, inside of struct "rt5033_charger" change the struct
"rt5033_charger_data" to non-pointer "chg". It is then initialized right
away and can be accessed more easily.
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Link: https://lore.kernel.org/r/0aff8c2a18cf4b88ec3333f6679a8419dd76ca29.1696165240.git.jahau@rocketmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Implement cable detection by extcon and handle the driver according to the
connector type.
There are basically three types of action: "set_charging", "set_otg" and
"set_disconnect".
A forth helper function to "unset_otg" was added because this is used in both
"set_charging" and "set_disconnect". In the first case it covers the rather
rare event that someone changes from OTG to charging without disconnect. In
the second case, when disconnecting, the values are set back to the ones from
initialization to return into a defined state.
Additionally, there is "set_mivr". When connecting to e.g. a laptop/PC, the
minimum input voltage regulation (MIVR) shall prevent a voltage drop if the
cable or the supply is weak. The MIVR value is set to 4600MV, same as in the
Android driver [1]. When disconnecting, MIVR is set back to DISABLED.
In the function rt5033_get_charger_state(): When in OTG mode, the chip
reports status "charging". Change this to "discharging" because there is
no charging going on in OTG mode [2].
Yang Yingliang detected missing mutex_unlock() in some error path and
suggested a fix [3]. The suggestion was squashed into this patch.
[1] https://github.com/msm8916-mainline/linux-downstream/blob/GT-I9195I/drivers/battery/rt5033_charger.c#L499
[2] https://github.com/msm8916-mainline/linux-downstream/blob/GT-I9195I/drivers/battery/rt5033_charger.c#L686-L687
[3] https://lore.kernel.org/linux-pm/20230822030207.644738-1-yangyingliang@huawei.com
Tested-by: Raymond Hackley <raymondhackley@protonmail.com>
Co-developed-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Link: https://lore.kernel.org/r/cc4e37e510abbb0cdfa7faa8408da48c2cb448a4.1696165240.git.jahau@rocketmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Enabling the tps65217-charger driver/module causes an interrupt conflict
with the vbus driver resulting in a probe failure.
The conflict is resolved by changing both driver's threaded interrupt
request function from IRQF_ONESHOT to IRQF_SHARED.
Signed-off-by: Grant B Adams <nemith592@gmail.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230823085430.6610-2-nemith592@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
string_lower from string_helpers.h can be used to modify the string
in-place. Use it to get rid of the custom str_to_lower().
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20230929-power_supply-string_lower-v1-1-3141a2634d53@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
There is a missing "ret = " assignment so this checks the same "ret"
value twice.
Fixes: c75f4bf6800b ("power: supply: Introduce MM8013 fuel gauge driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/c46b4408-bf1d-408d-9e6b-16b0ad272532@moroto.mountain
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add the missing endianness conversion when sending the enable request so
that the driver will work also on a hypothetical big-endian machine.
This issue was reported by sparse.
Fixes: 29e8142b5623 ("power: supply: Introduce Qualcomm PMIC GLINK power supply")
Cc: stable@vger.kernel.org # 6.3
Cc: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230929101649.20206-1-johan+linaro@kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
qcom_battmgr_update_request.battery_id is written to using cpu_to_le32()
and should be of type __le32, just like all other 32bit integer requests
for qcom_battmgr.
Cc: stable@vger.kernel.org # 6.3
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309162149.4owm9iXc-lkp@intel.com/
Fixes: 29e8142b5623 ("power: supply: Introduce Qualcomm PMIC GLINK power supply")
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230919124222.1155894-1-sebastian.reichel@collabora.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The value of ret is zero when passed to dev_error_probe(), we are passing
zero to dev_err_probe() is a success which is incorrect.
Fix this by getting the error code using PTR_ERR().
Fixes: c75f4bf6800b ("power: supply: Introduce MM8013 fuel gauge driver")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202309190838.eu8WS6sz-lkp@intel.com/
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20230923114807.2829188-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
__counted_by
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct axp20x_usb_power.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230922175358.work.774-kees@kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
__counted_by
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct axp20x_ac_power.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230922175355.work.006-kees@kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Dan Carpenter reports that the Smatch static checker warning has found
that there is another refcount leak in the probe function. While
of_node_put() was added in one of the return paths, it should in
fact be added for ALL return paths that return an error and at driver
removal time.
Fixes: 54c03bfd094f ("power: supply: Fix refcount leak in rk817_charger_probe")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Closes: https://lore.kernel.org/linux-pm/dc0bb0f8-212d-4be7-be69-becd2a3f9a80@kili.mountain/
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20230920145644.57964-1-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
power_supply_uevent() which is called to emit a udev event on device
deletion attempts to use the power_supply_battery_info structure,
which is device-managed and has been freed before this point.
Fix this by not generating all battery/charger properties when the
device is about to be removed. This also avoids generating errors
when trying to access the hardware in hot-unplug scenarios.
==================================================================
BUG: KASAN: slab-use-after-free in power_supply_battery_info_has_prop (power_supply_core.c:872)
Read of size 4 at addr 0000000062e59028 by task python3/27
Call Trace:
power_supply_battery_info_has_prop (power_supply_core.c:872)
power_supply_uevent (power_supply_sysfs.c:504)
dev_uevent (drivers/base/core.c:2590)
kobject_uevent_env (lib/kobject_uevent.c:558)
kobject_uevent (lib/kobject_uevent.c:643)
device_del (drivers/base/core.c:3266 drivers/base/core.c:3831)
device_unregister (drivers/base/core.c:3730 drivers/base/core.c:3854)
power_supply_unregister (power_supply_core.c:1608)
devm_power_supply_release (power_supply_core.c:1515)
release_nodes (drivers/base/devres.c:506)
devres_release_group (drivers/base/devres.c:669)
i2c_device_remove (drivers/i2c/i2c-core-base.c:629)
device_remove (drivers/base/dd.c:570)
device_release_driver_internal (drivers/base/dd.c:1274 drivers/base/dd.c:1295)
device_driver_detach (drivers/base/dd.c:1332)
unbind_store (drivers/base/bus.c:247)
...
Allocated by task 27:
devm_kmalloc (drivers/base/devres.c:119 drivers/base/devres.c:829)
power_supply_get_battery_info (include/linux/device.h:316 power_supply_core.c:626)
__power_supply_register (power_supply_core.c:1408)
devm_power_supply_register (power_supply_core.c:1544)
bq256xx_probe (bq256xx_charger.c:1539 bq256xx_charger.c:1727) bq256xx_charger
i2c_device_probe (drivers/i2c/i2c-core-base.c:584)
really_probe (drivers/base/dd.c:579 drivers/base/dd.c:658)
__driver_probe_device (drivers/base/dd.c:800)
device_driver_attach (drivers/base/dd.c:1128)
bind_store (drivers/base/bus.c:273)
...
Freed by task 27:
kfree (mm/slab_common.c:1073)
release_nodes (drivers/base/devres.c:503)
devres_release_all (drivers/base/devres.c:536)
device_del (drivers/base/core.c:3829)
device_unregister (drivers/base/core.c:3730 drivers/base/core.c:3854)
power_supply_unregister (power_supply_core.c:1608)
devm_power_supply_release (power_supply_core.c:1515)
release_nodes (drivers/base/devres.c:506)
devres_release_group (drivers/base/devres.c:669)
i2c_device_remove (drivers/i2c/i2c-core-base.c:629)
device_remove (drivers/base/dd.c:570)
device_release_driver_internal (drivers/base/dd.c:1274 drivers/base/dd.c:1295)
device_driver_detach (drivers/base/dd.c:1332)
unbind_store (drivers/base/bus.c:247)
...
==================================================================
Reported-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Fixes: 27a2195efa8d ("power: supply: core: auto-exposure of simple-battery data")
Tested-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
When CONFIG_EXTCON=m and CONFIG_CHARGER_PM8916_LBC=y, there are
build errors. Fix them by having CHARGER_PM8916_LBC depend on the
setting of EXTCON.
aarch64-linux-ld: drivers/power/supply/pm8916_lbc.o: in function `pm8916_lbc_charger_state_changed_irq':
pm8916_lbc.c:(.text+0xe8): undefined reference to `extcon_set_state_sync'
aarch64-linux-ld: drivers/power/supply/pm8916_lbc.o: in function `pm8916_lbc_charger_probe':
pm8916_lbc.c:(.text+0x638): undefined reference to `devm_extcon_dev_allocate'
aarch64-linux-ld: pm8916_lbc.c:(.text+0x650): undefined reference to `devm_extcon_dev_register'
aarch64-linux-ld: pm8916_lbc.c:(.text+0x688): undefined reference to `extcon_set_state_sync'
Fixes: f8d7a3d21160 ("power: supply: Add driver for pm8916 lbc")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Nikita Travkin <nikita@trvn.ru>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-pm@vger.kernel.org
Link: https://lore.kernel.org/r/20230918205825.25864-1-rdunlap@infradead.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-33-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-32-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-31-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-30-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-29-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-28-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-27-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-26-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-25-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-24-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-23-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-22-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-21-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-20-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-19-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-18-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-17-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-16-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-15-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-14-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-13-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-12-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230918133700.1254499-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
power_supply_notifier can be internal, since all users are going
through power_supply_reg_notifier()/power_supply_unreg_notifier().
Link: https://lore.kernel.org/r/20230913133900.591637-1-sebastian.reichel@collabora.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
While scanning the internet for MM8013 PDFs, I found one for a different
IC from Mitsumi, MM8118 at [1]. It turned out however, that when you
search through the PDF, the MM8118 text has an invsible text layer
containing "MM8013" underneath..
With some elbow grease, I was able to confirm that most of the registers
match between the two ICs. Based on that finding, introduce live battery
voltage readout, hw-decided charge behavior readout and max current
readout. Also, expand the existing POWER_SUPPLY_HEALTH reporting.
[1] https://product.minebeamitsumi.com/en/product/category/ics/battery/fuel_gauge/parts/download/__icsFiles/afieldfile/2023/07/12/1_download_01_12.pdf
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230916-topic-mm8013_2-v1-1-02495e07fca0@linaro.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
pm8916 LBC is a Linear Battery Charger hardware block in pm8916 PMIC.
This block implements simple CC/CV charging for Li-Po batteries.
The hardware has internal state machine to switch between modes and
works mostly autonomously, only needing the limits and targets to be
set to operate.
This driver allows setting limits and enabling the LBC block, monitoring
it's state.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20230915-pm8916-bms-lbc-v3-4-f30881e951a0@trvn.ru
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This driver adds basic support for VM-BMS found in pm8916.
VM-BMS is a very basic fuel-gauge hardware block that is, sadly,
incapable of any gauging. The hardware supports measuring OCV in
sleep mode, where the battery is not in use, or measuring average
voltage over time when the device is active.
This driver implements basic value readout from this block.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20230915-pm8916-bms-lbc-v3-3-f30881e951a0@trvn.ru
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Ensure that the dynamically created power supply device sets its
->of_node if the driver supplies one. This brings it in line with
several other subsystems (see git grep 'of_node =.*parent.*of_node') and
allows easier identification of the device from udev rules and similar.
Before this patch:
/sys/class/power_supply# ls -l bq256xx-battery/of_node
ls: cannot access 'bq256xx-battery/of_node': No such file or directory
# ls -l bq256xx-battery/hwmon1/of_node
ls: cannot access 'bq256xx-battery/hwmon1/of_node': No such file or directory
After:
/sys/class/power_supply# ls -l bq256xx-battery/of_node
lrwxrwxrwx 1 root root 0 May 17 09:14 bq256xx-battery/of_node ->
../../../../../../../../firmware/devicetree/base/virtio@1/i2c/bq25619@09
# ls -l bq256xx-battery/hwmon1/of_node
lrwxrwxrwx 1 root root 0 May 17 09:14 bq256xx-battery/hwmon1/of_node ->
../../../../../../../../../firmware/devicetree/base/virtio@1/i2c/bq25619@09
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20230915-power-of-v2-1-ca54c441867e@axis.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|