| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In both cases the type of da is u32. And PRU_PDRAM_DA is 0.
So the check da >= PRU_PDRAM_DA is always true and can be removed.
Flagged by Smatch:
drivers/remoteproc/pru_rproc.c:660 pru_d_da_to_va() warn: always true condition '(da >= 0) => (0-u32max >= 0)'
drivers/remoteproc/pru_rproc.c:709 pru_i_da_to_va() warn: always true condition '(da >= 0) => (0-u32max >= 0)'
No functional changes intended.
Compile tested only.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://www.spinics.net/lists/kernel/msg4025983.html
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Link: https://lore.kernel.org/r/20230404-pru-always-true-v1-1-b1b55eeff188@kernel.org
[Fixed typo in changelog]
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
Client device node property firmware-name is now used to configure
firmware for the PRU instances. The default firmware is also
restored once releasing the PRU resource.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230106121046.886863-7-danishanwar@ti.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
Some firmwares expect the OS drivers to configure the CTABLE
entries publishing dynamically allocated memory regions. For
example, the PRU Ethernet firmwares use the C28 and C30 entries
for retrieving the Shared RAM and System SRAM (OCMC) areas
allocated by the PRU Ethernet client driver.
Provide a way for users to do that through a new API,
pru_rproc_set_ctable(). The API returns 0 on success and
a negative value on error.
NOTE:
The programmable CTABLE entries are typically re-programmed by
the PRU firmwares when dealing with a certain block of memory
during block processing. This API provides an interface to the
PRU client drivers to publish a dynamically allocated memory
block with the PRU firmware using a CTABLE entry instead of a
negotiated address in shared memory. Additional synchronization
may be needed between the PRU client drivers and firmwares if
different addresses needs to be published at run-time reusing
the same CTABLE entry.
CTABLE for stands for "constant table".
Each CTable entry just holds the upper address bits so PRU can
reference to external memory with larger address bits.
For use case please see
prueth_sw_emac_config() in "drivers/net/ethernet/ti/prueth_switch.c"
/* Set in constant table C28 of PRUn to ICSS Shared memory */
pru_rproc_set_ctable(prueth->pru0, PRU_C28, sharedramaddr);
pru_rproc_set_ctable(prueth->pru1, PRU_C28, sharedramaddr);
/* Set in constant table C30 of PRUn to OCMC memory */
pru_rproc_set_ctable(prueth->pru0, PRU_C30, ocmcaddr);
pru_rproc_set_ctable(prueth->pru1, PRU_C30, ocmcaddr);
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20230106121046.886863-6-danishanwar@ti.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
The PRU remoteproc driver is not configured for 'auto-boot' by default,
and allows to be booted either by in-kernel PRU client drivers or by
userspace using the generic remoteproc sysfs interfaces. The sysfs
interfaces should not be permitted to change the remoteproc firmwares
or states when a PRU is being managed by an in-kernel client driver.
Use the newly introduced remoteproc generic 'sysfs_read_only' flag to
provide these restrictions by setting and clearing it appropriately
during the PRU acquire and release steps.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230106121046.886863-5-danishanwar@ti.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
Add two new APIs, pru_rproc_get() and pru_rproc_put(), to the PRU
driver to allow client drivers to acquire and release the remoteproc
device associated with a PRU core. The PRU cores are treated as
resources with only one client owning it at a time.
The pru_rproc_get() function returns the rproc handle corresponding
to a PRU core identified by the device tree "ti,prus" property under
the client node. The pru_rproc_put() is the complementary function
to pru_rproc_get().
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230106121046.886863-4-danishanwar@ti.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
Introducing enum pruss_pru_id for PRU Core Identifiers.
PRUSS_PRU0 indicates PRU Core 0.
PRUSS_PRU1 indicates PRU Core 1.
PRUSS_NUM_PRUS indicates the total number of PRU Cores.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230106121046.886863-3-danishanwar@ti.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
The K3 AM62x family of SoC has one PRUSS-M instance and it has two
Programmable Real-Time Units (PRU0 and PRU1). This does not support
Industrial Communications Subsystem features like Ethernet.
Enhance the existing PRU remoteproc driver to support the PRU cores
by using specific compatibles. The initial names for the firmware
images for each PRU core are retrieved from DT nodes, and can be adjusted
through sysfs if required.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20220602101920.12504-4-kishon@ti.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
The K3 AM64x family of SoCs have a ICSSG IP that is similar to the
version on AM65x SR2.0 SoCs with some minor differences. The AM64x
SoCs contain two instances of this newer ICSSG IP. Each ICSSG processor
subsystem contains 2 primary PRU cores, 2 auxiliary PRU cores called
RTUs, and 2 new auxiliary cores called Transmit PRUs (Tx_PRUs).
Enhance the existing PRU remoteproc driver to support all these PRU,
RTU and Tx_PRU cores by using specific compatibles. The cores have the
same memory copying limitations as on AM65x, so reuses the custom memcpy
function within the driver's ELF loader implementation. The initial
names for the firmware images for each PRU core are retrieved from
DT nodes, and can be adjusted through sysfs if required.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210623173243.7862-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This adds support to the remoteproc core for detaching Linux from a
running remoteproc, e.g. to reboot Linux while leaving the remoteproc
running, and it enable this support in the stm32 remoteproc driver.
It also introduces a property for memory carveouts to track if they
are iomem or system ram, to enable proper handling of the differences.
The imx_rproc received a number of fixes and improvements, in
particular support for attaching to already running remote processors
and i.MX8MQ and i.MX8MM support.
The Qualcomm wcss driver gained support for starting and stopping the
wireless subsystem on QCS404, when not using the TrustZone-based
validator/loader.
Finally it brings a few fixes to the TI PRU and to the firmware loader
for the Qualcomm modem subsystem drivers"
* tag 'rproc-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc: (53 commits)
remoteproc: stm32: add capability to detach
dt-bindings: remoteproc: stm32-rproc: add new mailbox channel for detach
remoteproc: imx_rproc: support remote cores booted before Linux Kernel
remoteproc: imx_rproc: move memory parsing to rproc_ops
remoteproc: imx_rproc: enlarge IMX7D_RPROC_MEM_MAX
remoteproc: imx_rproc: add missing of_node_put
remoteproc: imx_rproc: fix build error without CONFIG_MAILBOX
remoteproc: qcom: wcss: Remove unnecessary PTR_ERR()
remoteproc: qcom: wcss: Fix wrong pointer passed to PTR_ERR()
remoteproc: qcom: pas: Add modem support for SDX55
dt-bindings: remoteproc: qcom: pas: Add binding for SDX55
remoteproc: qcom: wcss: Fix return value check in q6v5_wcss_init_mmio()
remoteproc: pru: Fix and cleanup firmware interrupt mapping logic
remoteproc: pru: Fix wrong success return value for fw events
remoteproc: pru: Fixup interrupt-parent logic for fw events
remoteproc: qcom: wcnss: Allow specifying firmware-name
remoteproc: qcom: wcss: explicitly request exclusive reset control
remoteproc: qcom: wcss: Add non pas wcss Q6 support for QCS404
dt-bindings: remoteproc: qcom: Add Q6V5 Modem PIL binding for QCS404
remoteproc: qcom: wcss: populate hardcoded param using driver data
...
|
|
The PRU firmware interrupt mappings are configured and unconfigured in
.start() and .stop() callbacks respectively using the variables 'evt_count'
and a 'mapped_irq' pointer. These variables are modified only during these
callbacks but are not re-initialized/reset properly during unwind or
failure paths. These stale values caused a kernel crash while stopping a
PRU remoteproc running a different firmware with no events on a subsequent
run after a previous run that was running a firmware with events.
Fix this crash by ensuring that the evt_count is 0 and the mapped_irq
pointer is set to NULL in pru_dispose_irq_mapping(). Also, reset these
variables properly during any failures in the .start() callback. While
at this, the pru_dispose_irq_mapping() callsites are all made to look
the same, moving any conditional logic to inside the function.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Fixes: c75c9fdac66e ("remoteproc: pru: Add support for PRU specific interrupt configuration")
Reported-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210407155641.5501-4-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The irq_create_fwspec_mapping() returns a proper virq value on success
and 0 upon any failure. The pru_handle_intrmap() treats this as an error
and disposes all firmware event mappings correctly, but is returning
this incorrect value as is, letting the pru_rproc_start() interpret it
as a success and boot the PRU.
Fix this by returning an error value back upon any such failure. While
at this, revise the error trace to print some meaningful info about the
failed event.
Fixes: c75c9fdac66e ("remoteproc: pru: Add support for PRU specific interrupt configuration")
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20210407155641.5501-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The PRU firmware interrupt mapping logic in pru_handle_intrmap() uses
of_irq_find_parent() with PRU device node to get a handle to the PRUSS
Interrupt Controller at present. This logic however requires that the
PRU nodes always define a interrupt-parent property. This property is
neither a required/defined property as per the PRU remoteproc binding,
nor is relevant from a DT node point of view without any associated
interrupts. The current logic finds a wrong interrupt controller and
fails to perform proper mapping without any interrupt-parent property
in the PRU nodes.
Fix this logic to always find and use the sibling interrupt controller.
Also, while at this, fix the acquired interrupt controller device node
reference properly.
Fixes: c75c9fdac66e ("remoteproc: pru: Add support for PRU specific interrupt configuration")
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20210407155641.5501-2-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The K3 PRUs are 32-bit processors and in general have some limitations
in using the standard ARMv8 memcpy function for loading firmware segments,
so the driver already uses a custom memcpy implementation. This added
logic however is limited to only IRAMs at the moment, but the loading
into Data RAMs is not completely ok either and does generate a kernel
crash for unaligned accesses.
Fix these crashes by removing the existing IRAM logic limitation and
extending the custom memcpy usage to Data RAMs as well for all K3 SoCs.
Fixes: 1d39f4d19921 ("remoteproc: pru: Add support for various PRU cores on K3 AM65x SoCs")
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210315205859.19590-1-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Introduce an extra parameter is_iomem to da_to_va, then the caller
could take the memory as normal memory or io mapped memory.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1615029865-23312-5-git-send-email-peng.fan@oss.nxp.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Fix the following coccicheck warning:
./drivers/remoteproc/pru_rproc.c:247:0-23: WARNING:
pru_rproc_debug_ss_fops should be defined with DEFINE_DEBUGFS_ATTRIBUTE
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1614154829-42461-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
PRU port of GNU Binutils lacks support for separate address spaces.
PRU IRAM addresses are marked with artificial offset to differentiate
them from DRAM addresses. Hence remoteproc must mask IRAM addresses
coming from GNU ELF in order to get the true hardware address.
PRU firmware used for testing was the example in:
https://github.com/dinuxbg/pru-gcc-examples/tree/master/blinking-led/pru
Signed-off-by: Dimitar Dimitrov <dimitar@dinux.eu>
Link: https://lore.kernel.org/r/20201230105005.30492-1-dimitar@dinux.eu
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The K3 J721E family of SoCs have a revised version of the AM65x ICSSG IP
and contains two instances of this newer ICSSG IP. Each ICSSG processor
subsystem contains 2 primary PRU cores, 2 auxiliary PRU cores called RTUs,
and 2 new auxiliary cores called Transmit PRUs (Tx_PRUs).
Enhance the existing PRU remoteproc driver to support these new PRU
and RTU cores by using specific compatibles. The cores have the same
memory copying limitations as on AM65x, so reuses the custom memcpy
function within the driver's ELF loader implementation. The initial
names for the firmware images for each PRU core are retrieved from
DT nodes, and can be adjusted through sysfs if required.
Signed-off-by: Suman Anna <s-anna@ti.com>
Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201208141002.17777-7-grzegorz.jaszczyk@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The K3 AM65x family of SoCs have the next generation of the PRU-ICSS
processor subsystem, commonly referred to as ICSSG. Each ICSSG processor
subsystem on AM65x SR1.0 contains two primary PRU cores and two new
auxiliary PRU cores called RTUs. The AM65x SR2.0 SoCs have a revised
ICSSG IP that is based off the subsequent IP revision used on J721E
SoCs. This IP instance has two new custom auxiliary PRU cores called
Transmit PRUs (Tx_PRUs) in addition to the existing PRUs and RTUs.
Each RTU and Tx_PRU cores have their own dedicated IRAM (smaller than
a PRU), Control and debug feature sets, but is different in terms of
sub-modules integrated around it and does not have the full capabilities
associated with a PRU core. The RTU core is typically used to aid a
PRU core in accelerating data transfers, while the Tx_PRU cores is
normally used to control the TX L2 FIFO if enabled in Ethernet
applications. Both can also be used to run independent applications.
The RTU and Tx_PRU cores though share the same Data RAMs as the PRU
cores, so the memories have to be partitioned carefully between different
applications. The new cores also support a new sub-module called Task
Manager to support two different context thread executions.
Enhance the existing PRU remoteproc driver to support these new PRU, RTU
and Tx PRU cores by using specific compatibles. The initial names for the
firmware images for each PRU core are retrieved from DT nodes, and can
be adjusted through sysfs if required.
The PRU remoteproc driver has to be specifically modified to use a
custom memcpy function within its ELF loader implementation for these
new cores in order to overcome a limitation with copying data into each
of the core's IRAM memories. These memory ports support only 4-byte
writes, and any sub-word order byte writes clear out the remaining
bytes other than the bytes being written within the containing word.
The default ARM64 memcpy also cannot be used as it throws an exception
when the preferred 8-byte copy operation is attempted. This choice is
made by using a state flag that is set only on K3 SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201208141002.17777-6-grzegorz.jaszczyk@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The remoteproc core creates certain standard debugfs entries,
that does not give a whole lot of useful information for the
PRUs. The PRU remoteproc driver is enhanced to add additional
debugfs entries for PRU. These will be auto-cleaned up when
the parent rproc debug directory is removed.
The enhanced debugfs support adds two new entries: 'regs' and
'single_step'. The 'regs' dumps out the useful CTRL sub-module
registers as well as each of the 32 GPREGs and CT_REGs registers.
The GPREGs and CT_REGs though are printed only when the PRU is
halted and accessible as per the IP design.
The 'single_step' utilizes the single-step execution of the PRU
cores. Writing a non-zero value performs a single step, and a
zero value restores the PRU to execute in the same mode as the
mode before the first single step. (note: if the PRU is halted
because of a halt instruction, then no change occurs).
Logic for setting the PC and jumping over a halt instruction shall
be added in the future.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201208141002.17777-5-grzegorz.jaszczyk@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The firmware blob can contain optional ELF sections: .resource_table
section and .pru_irq_map one. The second one contains the PRUSS
interrupt mapping description, which needs to be setup before powering
on the PRU core. To avoid RAM wastage this ELF section is not mapped to
any ELF segment (by the firmware linker) and therefore is not loaded to
PRU memory.
The PRU interrupt configuration is handled within the PRUSS INTC irqchip
driver and leverages the system events to interrupt channels and host
interrupts mapping configuration. Relevant irq routing information is
passed through a special .pru_irq_map ELF section (for interrupts routed
to and used by PRU cores) or via the PRU application's device tree node
(for interrupts routed to and used by the main CPU). The mappings are
currently programmed during the booting/shutdown of the PRU.
The interrupt configuration passed through .pru_irq_map ELF section is
optional. It varies on specific firmware functionality and therefore
have to be unwinded during PRU stop and performed again during
PRU start.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Co-developed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Link: https://lore.kernel.org/r/20201208141002.17777-4-grzegorz.jaszczyk@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The Programmable Real-Time Unit Subsystem (PRUSS) consists of
dual 32-bit RISC cores (Programmable Real-Time Units, or PRUs)
for program execution. This patch adds a remoteproc platform
driver for managing the individual PRU RISC cores life cycle.
The PRUs do not have a unified address space (have an Instruction
RAM and a primary Data RAM at both 0x0). The PRU remoteproc driver
therefore uses a custom remoteproc core ELF loader ops. The added
.da_to_va ops is only used to provide translations for the PRU
Data RAMs. This remoteproc driver does not have support for error
recovery and system suspend/resume features. Different compatibles
are used to allow providing scalability for instance-specific device
data if needed. The driver uses a default firmware-name retrieved
from device-tree for each PRU core, and the firmwares are expected
to be present in the standard Linux firmware search paths. They can
also be adjusted by userspace if required through the sysfs interface
provided by the remoteproc core.
The PRU remoteproc driver uses a client-driven boot methodology: it
does _not_ support auto-boot so that the PRU load and boot is dictated
by the corresponding client drivers for achieving various usecases.
This allows flexibility for the client drivers or applications to set
a firmware name (if needed) based on their desired functionality and
boot the PRU. The sysfs bind and unbind attributes have also been
suppressed so that the PRU devices cannot be unbound and thereby
shutdown a PRU from underneath a PRU client driver.
The driver currently supports the AM335x, AM437x, AM57xx and 66AK2G
SoCs, and support for other TI SoCs will be added in subsequent
patches.
Co-developed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201208141002.17777-3-grzegorz.jaszczyk@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
