Age | Commit message (Collapse) | Author | Files | Lines |
|
commit 1abc900ddda8ad2ef739fedf498d415655b6c3b8 upstream.
Some firmware versions of the 9600 series SAS HBA byte-swap the REPORT
ZONES command reply buffer from ATA-ZAC devices by directly accessing the
buffer in the host memory. This does not respect the default command DMA
direction and causes IOMMU page faults on architectures with an IOMMU
enforcing write-only mappings for DMA_FROM_DEVICE DMA direction (e.g. AMD
hosts), leading to the device capacity to be dropped to 0:
scsi 18:0:58:0: Direct-Access-ZBC ATA WDC WSH722626AL W930 PQ: 0 ANSI: 7
scsi 18:0:58:0: Power-on or device reset occurred
sd 18:0:58:0: Attached scsi generic sg9 type 20
sd 18:0:58:0: [sdj] Host-managed zoned block device
mpi3mr 0000:c1:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0001 address=0xfec0c400 flags=0x0050]
mpi3mr 0000:c1:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0001 address=0xfec0c500 flags=0x0050]
sd 18:0:58:0: [sdj] REPORT ZONES start lba 0 failed
sd 18:0:58:0: [sdj] REPORT ZONES: Result: hostbyte=DID_SOFT_ERROR driverbyte=DRIVER_OK
sd 18:0:58:0: [sdj] 0 4096-byte logical blocks: (0 B/0 B)
sd 18:0:58:0: [sdj] Write Protect is off
sd 18:0:58:0: [sdj] Mode Sense: 6b 00 10 08
sd 18:0:58:0: [sdj] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 18:0:58:0: [sdj] Attached SCSI disk
Avoid this issue by always mapping the buffer of REPORT ZONES commands
using DMA_BIDIRECTIONAL, that is, using a read-write IOMMU mapping.
Suggested-by: Christoph Hellwig <hch@lst.de>
Fixes: 023ab2a9b4ed ("scsi: mpi3mr: Add support for queue command processing")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240719073913.179559-2-dlemoal@kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 82dbb57ac8d06dfe8227ba9ab11a49de2b475ae5 upstream.
Some firmware versions of the 9600 series SAS HBA byte-swap the REPORT
ZONES command reply buffer from ATA-ZAC devices by directly accessing the
buffer in the host memory. This does not respect the default command DMA
direction and causes IOMMU page faults on architectures with an IOMMU
enforcing write-only mappings for DMA_FROM_DEVICE DMA driection (e.g. AMD
hosts).
scsi 18:0:0:0: Direct-Access-ZBC ATA WDC WSH722020AL W870 PQ: 0 ANSI: 6
scsi 18:0:0:0: SATA: handle(0x0027), sas_addr(0x300062b2083e7c40), phy(0), device_name(0x5000cca29dc35e11)
scsi 18:0:0:0: enclosure logical id (0x300062b208097c40), slot(0)
scsi 18:0:0:0: enclosure level(0x0000), connector name( C0.0)
scsi 18:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
scsi 18:0:0:0: qdepth(32), tagged(1), scsi_level(7), cmd_que(1)
sd 18:0:0:0: Attached scsi generic sg2 type 20
sd 18:0:0:0: [sdc] Host-managed zoned block device
mpt3sas 0000:41:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0xfff9b200 flags=0x0050]
mpt3sas 0000:41:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0xfff9b300 flags=0x0050]
mpt3sas_cm0: mpt3sas_ctl_pre_reset_handler: Releasing the trace buffer due to adapter reset.
mpt3sas_cm0 fault info from func: mpt3sas_base_make_ioc_ready
mpt3sas_cm0: fault_state(0x2666)!
mpt3sas_cm0: sending diag reset !!
mpt3sas_cm0: diag reset: SUCCESS
sd 18:0:0:0: [sdc] REPORT ZONES start lba 0 failed
sd 18:0:0:0: [sdc] REPORT ZONES: Result: hostbyte=DID_RESET driverbyte=DRIVER_OK
sd 18:0:0:0: [sdc] 0 4096-byte logical blocks: (0 B/0 B)
Avoid such issue by always mapping the buffer of REPORT ZONES commands
using DMA_BIDIRECTIONAL (read+write IOMMU mapping). This is done by
introducing the helper function _base_scsi_dma_map() and using this helper
in _base_build_sg_scmd() and _base_build_sg_scmd_ieee() instead of calling
directly scsi_dma_map().
Fixes: 471ef9d4e498 ("mpt3sas: Build MPI SGL LIST on GEN2 HBAs and IEEE SGL LIST on GEN3 HBAs")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240719073913.179559-3-dlemoal@kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit da3e19ef0b3de0aa4b25595bdc214c02a04f19b8 upstream.
This reverts commit 7a6bbc2829d4ab592c7e440a6f6f5deb3cd95db4.
The offending commit tried to suppress a double "Starting disk" message for
some drivers, but instead started spamming the log with bogus messages
every five seconds:
[ 311.798956] sd 0:0:0:0: [sda] Starting disk
[ 316.919103] sd 0:0:0:0: [sda] Starting disk
[ 322.040775] sd 0:0:0:0: [sda] Starting disk
[ 327.161140] sd 0:0:0:0: [sda] Starting disk
[ 332.281352] sd 0:0:0:0: [sda] Starting disk
[ 337.401878] sd 0:0:0:0: [sda] Starting disk
[ 342.521527] sd 0:0:0:0: [sda] Starting disk
[ 345.850401] sd 0:0:0:0: [sda] Starting disk
[ 350.967132] sd 0:0:0:0: [sda] Starting disk
[ 356.090454] sd 0:0:0:0: [sda] Starting disk
...
on machines that do not actually stop the disk on runtime suspend (e.g.
the Qualcomm sc8280xp CRD with UFS).
Let's just revert for now to address the regression.
Fixes: 7a6bbc2829d4 ("scsi: sd: Do not repeat the starting disk message")
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240716161101.30692-1-johan+linaro@kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9f499b8c791d2983c0a31a543c51d1b2f15e8755 upstream.
While working on simplifying the minmax functions, and avoiding
excessive macro expansion, it turns out that the sr.c use of the
'clamp()' macro has the arguments the wrong way around.
The clamp logic is
val = clamp(in, low, high);
and it returns the input clamped to the low/high limits. But sr.c ddid
speed = clamp(0, speed, 0xffff / 177);
which clamps the value '0' to the range '[speed, 0xffff / 177]' and ends
up being nonsensical.
Happily, I don't think anybody ever cared.
Fixes: 9fad9d560af5 ("scsi: sr: Fix unintentional arithmetic wraparound")
Cc: Justin Stitt <justinstitt@google.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eb1d4ce2609584eeb7694866f34d4b213caa3af9 upstream.
The driver load failed with error message,
qla2xxx [0000:04:00.0]-ffff:0: register_localport failed: ret=ffffffef
and with a kernel crash,
BUG: unable to handle kernel NULL pointer dereference at 0000000000000070
Workqueue: events_unbound qla_register_fcport_fn [qla2xxx]
RIP: 0010:nvme_fc_register_remoteport+0x16/0x430 [nvme_fc]
RSP: 0018:ffffaaa040eb3d98 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffff9dfb46b78c00 RCX: 0000000000000000
RDX: ffff9dfb46b78da8 RSI: ffffaaa040eb3e08 RDI: 0000000000000000
RBP: ffff9dfb612a0a58 R08: ffffffffaf1d6270 R09: 3a34303a30303030
R10: 34303a303030305b R11: 2078787832616c71 R12: ffff9dfb46b78dd4
R13: ffff9dfb46b78c24 R14: ffff9dfb41525300 R15: ffff9dfb46b78da8
FS: 0000000000000000(0000) GS:ffff9dfc67c00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000070 CR3: 000000018da10004 CR4: 00000000000206f0
Call Trace:
qla_nvme_register_remote+0xeb/0x1f0 [qla2xxx]
? qla2x00_dfs_create_rport+0x231/0x270 [qla2xxx]
qla2x00_update_fcport+0x2a1/0x3c0 [qla2xxx]
qla_register_fcport_fn+0x54/0xc0 [qla2xxx]
Exit the qla_nvme_register_remote() function when qla_nvme_register_hba()
fails and correctly validate nvme_local_port.
Cc: stable@vger.kernel.org
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240710171057.35066-3-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4475afa2646d3fec176fc4d011d3879b26cb26e3 upstream.
A crash was observed while performing NPIV and FW reset,
BUG: kernel NULL pointer dereference, address: 000000000000001c
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 1 PREEMPT_RT SMP NOPTI
RIP: 0010:dma_direct_unmap_sg+0x51/0x1e0
RSP: 0018:ffffc90026f47b88 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000021 RCX: 0000000000000002
RDX: 0000000000000021 RSI: 0000000000000000 RDI: ffff8881041130d0
RBP: ffff8881041130d0 R08: 0000000000000000 R09: 0000000000000034
R10: ffffc90026f47c48 R11: 0000000000000031 R12: 0000000000000000
R13: 0000000000000000 R14: ffff8881565e4a20 R15: 0000000000000000
FS: 00007f4c69ed3d00(0000) GS:ffff889faac80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000000001c CR3: 0000000288a50002 CR4: 00000000007706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<TASK>
? __die_body+0x1a/0x60
? page_fault_oops+0x16f/0x4a0
? do_user_addr_fault+0x174/0x7f0
? exc_page_fault+0x69/0x1a0
? asm_exc_page_fault+0x22/0x30
? dma_direct_unmap_sg+0x51/0x1e0
? preempt_count_sub+0x96/0xe0
qla2xxx_qpair_sp_free_dma+0x29f/0x3b0 [qla2xxx]
qla2xxx_qpair_sp_compl+0x60/0x80 [qla2xxx]
__qla2x00_abort_all_cmds+0xa2/0x450 [qla2xxx]
The command completion was done early while aborting the commands in driver
unload path but outside lock to avoid the WARN_ON condition of performing
dma_free_attr within the lock. However this caused race condition while
command completion via multiple paths causing system crash.
Hence complete the command early in unload path but within the lock to
avoid race condition.
Fixes: 0367076b0817 ("scsi: qla2xxx: Perform lockless command completion in abort path")
Cc: stable@vger.kernel.org
Signed-off-by: Shreyas Deodhar <sdeodhar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240710171057.35066-7-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 29e222085d8907ccff18ecd931bdd4c6b1f11b92 upstream.
Link up failure is observed as a result of flash read failure. Current
code does not check flash read return code where it relies on FW checksum
to detect the problem.
Add check of flash read failure to detect the problem sooner.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/202406210815.rPDRDMBi-lkp@intel.com/
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240710171057.35066-6-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit beafd692461443e0fb1d61aa56886bf85ef6f5e4 upstream.
For fabric scan, current code uses switch scan opcode and flags as the
method to iterate through different commands to carry out the process.
This makes it hard to read. This patch convert those opcode and flags into
steps. In addition, this help reduce some duplicate code.
Consolidate routines that handle GPNFT & GNNFT.
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240710171057.35066-10-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c449b4198701d828e40d60a2abd30970b74a1d75 upstream.
On bsg timeout, hardware_lock is used as part of search for the srb.
Instead, qpair lock should be used to iterate through different qpair.
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240710171057.35066-11-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c03d740152f78e86945a75b2ad541bf972fab92a upstream.
Init Control Block is dereferenced incorrectly. Correctly dereference ICB
Cc: stable@vger.kernel.org
Signed-off-by: Shreyas Deodhar <sdeodhar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240710171057.35066-4-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c3d98b12eef8db436e32f1a8c5478be57dc15621 upstream.
The device does not come online when the target port is online. There were
multiple RSCNs indicating multiple devices were affected. Driver is in the
process of finishing a fabric scan. A new RSCN (device up) arrived at the
tail end of the last fabric scan. Driver mistakenly thinks the new RSCN is
being taken care of by the previous fabric scan, where this notification is
cleared and not acted on. The laser needs to be blinked again to get the
device to show up.
To prevent driver from accidentally clearing the RSCN notification, each
RSCN is given a generation value. A fabric scan will scan for that
generation(s). Any new RSCN arrive after the scan start will have a new
generation value. This will trigger another scan to get latest data. The
RSCN notification flag will be cleared when the scan is associate to that
generation.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202406210538.w875N70K-lkp@intel.com/
Fixes: bb2ca6b3f09a ("scsi: qla2xxx: Relogin during fabric disturbance")
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240710171057.35066-2-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 76f480d7c717368f29a3870f7d64471ce0ff8fb2 upstream.
During vport delete, it is observed that during unload we hit a crash
because of stale entries in outstanding command array. For all these stale
I/O entries, eh_abort was issued and aborted (fast_fail_io = 2009h) but
I/Os could not complete while vport delete is in process of deleting.
BUG: kernel NULL pointer dereference, address: 000000000000001c
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
Workqueue: qla2xxx_wq qla_do_work [qla2xxx]
RIP: 0010:dma_direct_unmap_sg+0x51/0x1e0
RSP: 0018:ffffa1e1e150fc68 EFLAGS: 00010046
RAX: 0000000000000000 RBX: 0000000000000021 RCX: 0000000000000001
RDX: 0000000000000021 RSI: 0000000000000000 RDI: ffff8ce208a7a0d0
RBP: ffff8ce208a7a0d0 R08: 0000000000000000 R09: ffff8ce378aac9c8
R10: ffff8ce378aac8a0 R11: ffffa1e1e150f9d8 R12: 0000000000000000
R13: 0000000000000000 R14: ffff8ce378aac9c8 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff8d217f000000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000000001c CR3: 0000002089acc000 CR4: 0000000000350ee0
Call Trace:
<TASK>
qla2xxx_qpair_sp_free_dma+0x417/0x4e0
? qla2xxx_qpair_sp_compl+0x10d/0x1a0
? qla2x00_status_entry+0x768/0x2830
? newidle_balance+0x2f0/0x430
? dequeue_entity+0x100/0x3c0
? qla24xx_process_response_queue+0x6a1/0x19e0
? __schedule+0x2d5/0x1140
? qla_do_work+0x47/0x60
? process_one_work+0x267/0x440
? process_one_work+0x440/0x440
? worker_thread+0x2d/0x3d0
? process_one_work+0x440/0x440
? kthread+0x156/0x180
? set_kthread_struct+0x50/0x50
? ret_from_fork+0x22/0x30
</TASK>
Send out async logout explicitly for all the ports during vport delete.
Cc: stable@vger.kernel.org
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240710171057.35066-8-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9609385dd91b26751019b22ca9bfa4bec7602ae1 upstream.
Certain vendor specific targets initially register with the fabric as an
initiator function first and then re-register as a target function
afterwards.
The timing of the target function re-registration can cause a race
condition such that the driver is stuck assuming the remote port as an
initiator function and never discovers the target's hosted LUNs.
Expand the nlp_state qualifier to also include NLP_STE_PRLI_ISSUE because
the state means that PRLI was issued but we have not quite reached
MAPPED_NODE state yet. If we received an RSCN in the PRLI_ISSUE state,
then we should restart discovery again by going into DEVICE_RECOVERY.
Fixes: dded1dc31aa4 ("scsi: lpfc: Modify when a node should be put in device recovery mode during RSCN")
Cc: <stable@vger.kernel.org> # v6.6+
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240628172011.25921-3-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ce2065c4cc4f05635413f63f6dc038d7d4842e31 upstream.
Firmware only supports single DSDs in ELS Pass-through IOCB (0x53h), sg cnt
is decided by the SCSI ML. User is not aware of the cause of an acutal
error.
Return the appropriate return code that will be decoded by API and
application and proper error message will be displayed to user.
Fixes: 6e98016ca077 ("[SCSI] qla2xxx: Re-organized BSG interface specific code.")
Cc: stable@vger.kernel.org
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240710171057.35066-5-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 348744f27a35e087acc9378bf53537fbfb072775 upstream.
Bios version was popluated for FDMI response. Systems with EFI would show
optrom version as 0. EFI version is populated here and BIOS version is
already displayed under FDMI_HBA_BOOT_BIOS_NAME.
Cc: stable@vger.kernel.org
Signed-off-by: Shreyas Deodhar <sdeodhar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240710171057.35066-9-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8bc7c617642db6d8d20ee671fb6c4513017e7a7e ]
On big endian architectures, it is possible to run into a memory out of
bounds pointer dereference when FCP targets are zoned.
In lpfc_prep_embed_io, the memcpy(ptr, fcp_cmnd, sgl->sge_len) is
referencing a little endian formatted sgl->sge_len value. So, the memcpy
can cause big endian systems to crash.
Redefine the *sgl ptr as a struct sli4_sge_le to make it clear that we are
referring to a little endian formatted data structure. And, update the
routine with proper le32_to_cpu macro usages.
Fixes: af20bb73ac25 ("scsi: lpfc: Add support for 32 byte CDBs")
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240628172011.25921-8-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5e0bf3e8aec2cbc51123f84b29aaacbd91fc56fa ]
In function lpfc_xcvr_data_show, the memory allocation with kmalloc might
fail, thereby making rdp_context a null pointer. In the following context
and functions that use this pointer, there are dereferencing operations,
leading to null pointer dereference.
To fix this issue, a null pointer check should be added. If it is null,
use scnprintf to notify the user and return len.
Fixes: 479b0917e447 ("scsi: lpfc: Create a sysfs entry called lpfc_xcvr_data for transceiver info")
Signed-off-by: Huai-Yuan Liu <qq810974084@gmail.com>
Link: https://lore.kernel.org/r/20240621082545.449170-1-qq810974084@gmail.com
Reviewed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"One core change that moves a disk start message to a location where it
will only be printed once instead of twice plus a couple of error
handling race fixes in the ufs driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: Do not repeat the starting disk message
scsi: ufs: core: Fix ufshcd_abort_one racing issue
scsi: ufs: core: Fix ufshcd_clear_cmd racing issue
|
|
The SCSI disk message "Starting disk" to signal resuming of a suspended
disk is printed in both sd_resume() and sd_resume_common() which results
in this message being printed twice when resuming from e.g. autosuspend:
$ echo 5000 > /sys/block/sda/device/power/autosuspend_delay_ms
$ echo auto > /sys/block/sda/device/power/control
[ 4962.438293] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 4962.501121] sd 0:0:0:0: [sda] Stopping disk
$ echo on > /sys/block/sda/device/power/control
[ 4972.805851] sd 0:0:0:0: [sda] Starting disk
[ 4980.558806] sd 0:0:0:0: [sda] Starting disk
Fix this double print by removing the call to sd_printk() from sd_resume()
and moving the call to sd_printk() in sd_resume_common() earlier in the
function, before the check using sd_do_start_stop(). Doing so, the message
is printed once regardless if sd_resume_common() actually executes
sd_start_stop_device() (i.e. SCSI device case) or not (libsas and libata
managed ATA devices case).
Fixes: 0c76106cb975 ("scsi: sd: Fix TCG OPAL unlock on system resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240701215326.128067-1-dlemoal@kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A couple of error leg problems, one affecting scsi_debug and the other
affecting pure SAS (i.e. not SATA) SCSI expanders"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: libsas: Fix exp-attached device scan after probe failure scanned in again after probe failed
scsi: scsi_debug: Fix create target debugfs failure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata fixes from Niklas Cassel:
- Add NOLPM quirk for for all Crucial BX SSD1 models.
Considering that we now have had bug reports for 3 different BX SSD1
variants from Crucial with the same product name, make the quirk more
inclusive, to catch more device models from the same generation.
- Fix a trivial NULL pointer dereference in the error path for
ata_host_release().
- Create a ata_port_free(), so that we don't miss freeing ata_port
struct members when freeing a struct ata_port.
- Fix a trivial double free in the error path for ata_host_alloc().
- Ensure that we remove the libata "remapped NVMe device count" sysfs
entry on .probe() error.
* tag 'ata-6.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: ahci: Clean up sysfs file on error
ata: libata-core: Fix double free on error
ata,scsi: libata-core: Do not leak memory for ata_port struct members
ata: libata-core: Fix null pointer dereference on error
ata: libata-core: Add ATA_HORKAGE_NOLPM for all Crucial BX SSD1 models
|
|
libsas is currently not freeing all the struct ata_port struct members,
e.g. ncq_sense_buf for a driver supporting Command Duration Limits (CDL).
Add a function, ata_port_free(), that is used to free a ata_port,
including its struct members. It makes sense to keep the code related to
freeing a ata_port in its own function, which will also free all the
struct members of struct ata_port.
Fixes: 18bd7718b5c4 ("scsi: ata: libata: Handle completion of CDL commands using policy 0xD")
Reviewed-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240629124210.181537-8-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
again after probe failed
The expander phy will be treated as broadcast flutter in the next
revalidation after the exp-attached end device probe failed, as follows:
[78779.654026] sas: broadcast received: 0
[78779.654037] sas: REVALIDATING DOMAIN on port 0, pid:10
[78779.654680] sas: ex 500e004aaaaaaa1f phy05 change count has changed
[78779.662977] sas: ex 500e004aaaaaaa1f phy05 originated BROADCAST(CHANGE)
[78779.662986] sas: ex 500e004aaaaaaa1f phy05 new device attached
[78779.663079] sas: ex 500e004aaaaaaa1f phy05:U:8 attached: 500e004aaaaaaa05 (stp)
[78779.693542] hisi_sas_v3_hw 0000:b4:02.0: dev[16:5] found
[78779.701155] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[78779.707864] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
...
[78835.161307] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[78835.171344] sas: sas_probe_sata: for exp-attached device 500e004aaaaaaa05 returned -19
[78835.180879] hisi_sas_v3_hw 0000:b4:02.0: dev[16:5] is gone
[78835.187487] sas: broadcast received: 0
[78835.187504] sas: REVALIDATING DOMAIN on port 0, pid:10
[78835.188263] sas: ex 500e004aaaaaaa1f phy05 change count has changed
[78835.195870] sas: ex 500e004aaaaaaa1f phy05 originated BROADCAST(CHANGE)
[78835.195875] sas: ex 500e004aaaaaaa1f rediscovering phy05
[78835.196022] sas: ex 500e004aaaaaaa1f phy05:U:A attached: 500e004aaaaaaa05 (stp)
[78835.196026] sas: ex 500e004aaaaaaa1f phy05 broadcast flutter
[78835.197615] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
The cause of the problem is that the related ex_phy's attached_sas_addr was
not cleared after the end device probe failed, so reset it.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20240619091742.25465-1-yangxingui@huawei.com
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Target debugfs entry is removed via async_schedule() which isn't drained
when adding same name target, so failure of "Directory 'target11:0:0' with
parent 'scsi_debug' already present!" can be triggered easily.
Fix it by switching to domain async schedule, and draining it before
adding new target debugfs entry.
Cc: Wenchao Hao <haowenchao2@huawei.com>
Fixes: f084fe52c640 ("scsi: scsi_debug: Add debugfs interface to fail target reset")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Wenchao Hao <haowenchao22@gmail.com>
Link: https://lore.kernel.org/r/20240619013803.3008857-1-ming.lei@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two fixes: one in the ufs driver fixing an obvious memory leak and the
other (with a core flag based update) trying to prevent USB crashes by
stopping the core from issuing a request for the I/O Hints mode page"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: usb: uas: Do not query the IO Advice Hints Grouping mode page for USB/UAS devices
scsi: core: Introduce the BLIST_SKIP_IO_HINTS flag
scsi: ufs: core: Free memory allocated for model before reinit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three obvious driver fixes and two core fixes.
The two core fixes are to disable Command Duration Limits by default
to fix an inconsistency in SATA and some USB devices. The other is to
change the default read size for block zero to follow the device
preference (some USB bridges preferring 16 byte commands don't have a
translation for READ(10) and thus don't scan properly)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mpi3mr: Fix ATA NCQ priority support
scsi: ufs: core: Quiesce request queues before checking pending cmds
scsi: core: Disable CDL by default
scsi: mpt3sas: Avoid test/set_bit() operating in non-allocated memory
scsi: sd: Use READ(16) when reading block zero on large capacity disks
|
|
Prepare for skipping the IO Advice Hints Grouping mode page for USB storage
devices.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Joao Machado <jocrismachado@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Christian Heusel <christian@heusel.eu>
Cc: stable@vger.kernel.org
Fixes: 4f53138fffc2 ("scsi: sd: Translate data lifetime information")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240613211828.2077477-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The function mpi3mr_qcmd() of the mpi3mr driver is able to indicate to
the HBA if a read or write command directed at an ATA device should be
translated to an NCQ read/write command with the high prioiryt bit set
when the request uses the RT priority class and the user has enabled NCQ
priority through sysfs.
However, unlike the mpt3sas driver, the mpi3mr driver does not define
the sas_ncq_prio_supported and sas_ncq_prio_enable sysfs attributes, so
the ncq_prio_enable field of struct mpi3mr_sdev_priv_data is never
actually set and NCQ Priority cannot ever be used.
Fix this by defining these missing atributes to allow a user to check if
an ATA device supports NCQ priority and to enable/disable the use of NCQ
priority. To do this, lift the function scsih_ncq_prio_supp() out of the
mpt3sas driver and make it the generic SCSI SAS transport function
sas_ata_ncq_prio_supported(). Nothing in that function is hardware
specific, so this function can be used in both the mpt3sas driver and
the mpi3mr driver.
Reported-by: Scott McCoy <scott.mccoy@wdc.com>
Fixes: 023ab2a9b4ed ("scsi: mpi3mr: Add support for queue command processing")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240611083435.92961-1-dlemoal@kernel.org
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For SCSI devices supporting the Command Duration Limits feature set, the
user can enable/disable this feature use through the sysfs device attribute
"cdl_enable". This attribute modification triggers a call to
scsi_cdl_enable() to enable and disable the feature for ATA devices and set
the scsi device cdl_enable field to the user provided bool value. For SCSI
devices supporting CDL, the feature set is always enabled and
scsi_cdl_enable() is reduced to setting the cdl_enable field.
However, for ATA devices, a drive may spin-up with the CDL feature enabled
by default. But the SCSI device cdl_enable field is always initialized to
false (CDL disabled), regardless of the actual device CDL feature
state. For ATA devices managed by libata (or libsas), libata-core always
disables the CDL feature set when the device is attached, thus syncing the
state of the CDL feature on the device and of the SCSI device cdl_enable
field. However, for ATA devices connected to a SAS HBA, the CDL feature is
not disabled on scan for ATA devices that have this feature enabled by
default, leading to an inconsistent state of the feature on the device with
the SCSI device cdl_enable field.
Avoid this inconsistency by adding a call to scsi_cdl_enable() in
scsi_cdl_check() to make sure that the device-side state of the CDL feature
set always matches the scsi device cdl_enable field state. This implies
that CDL will always be disabled for ATA devices connected to SAS HBAs,
which is consistent with libata/libsas initialization of the device.
Reported-by: Scott McCoy <scott.mccoy@wdc.com>
Fixes: 1b22cfb14142 ("scsi: core: Allow enabling and disabling command duration limits")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240607012507.111488-1-dlemoal@kernel.org
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"The core change is to detect unusually large number of VPD pages
(caused by device manufacturers having an endiannes issue) and reject
them rather than trying to parse a huge non-existent array.
The remaining fixes are in drivers the most user visible of which is
the ALUA state transition recognition (leads to intermittent I/O
errors in some situations otherwise)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: mcq: Fix error output and clean up ufshcd_mcq_abort()
scsi: core: Handle devices which return an unusually large VPD page count
scsi: mpt3sas: Add missing kerneldoc parameter descriptions
scsi: qedf: Set qed_slowpath_params to zero before use
scsi: qedf: Wait for stag work during unload
scsi: qedf: Don't process stag work during unload and recovery
scsi: sr: Fix unintentional arithmetic wraparound
scsi: core: alua: I/O errors for ALUA state transitions
scsi: mpi3mr: Use proper format specifier in mpi3mr_sas_port_add()
|
|
There is a potential out-of-bounds access when using test_bit() on a single
word. The test_bit() and set_bit() functions operate on long values, and
when testing or setting a single word, they can exceed the word
boundary. KASAN detects this issue and produces a dump:
BUG: KASAN: slab-out-of-bounds in _scsih_add_device.constprop.0 (./arch/x86/include/asm/bitops.h:60 ./include/asm-generic/bitops/instrumented-atomic.h:29 drivers/scsi/mpt3sas/mpt3sas_scsih.c:7331) mpt3sas
Write of size 8 at addr ffff8881d26e3c60 by task kworker/u1536:2/2965
For full log, please look at [1].
Make the allocation at least the size of sizeof(unsigned long) so that
set_bit() and test_bit() have sufficient room for read/write operations
without overwriting unallocated memory.
[1] Link: https://lore.kernel.org/all/ZkNcALr3W3KGYYJG@gmail.com/
Fixes: c696f7b83ede ("scsi: mpt3sas: Implement device_remove_in_progress check in IOCTL path")
Cc: stable@vger.kernel.org
Suggested-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240605085530.499432-1-leitao@debian.org
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 321da3dc1f3c ("scsi: sd: usb_storage: uas: Access media prior
to querying device properties") triggered a read to LBA 0 before
attempting to inquire about device characteristics. This was done
because some protocol bridge devices will return generic values until
an attached storage device's media has been accessed.
Pierre Tomon reported that this change caused problems on a large
capacity external drive connected via a bridge device. The bridge in
question does not appear to implement the READ(10) command.
Issue a READ(16) instead of READ(10) when a device has been identified
as preferring 16-byte commands (use_16_for_rw heuristic).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218890
Link: https://lore.kernel.org/r/70dd7ae0-b6b1-48e1-bb59-53b7c7f18274@rowland.harvard.edu
Link: https://lore.kernel.org/r/20240605022521.3960956-1-martin.petersen@oracle.com
Fixes: 321da3dc1f3c ("scsi: sd: usb_storage: uas: Access media prior to querying device properties")
Cc: stable@vger.kernel.org
Reported-by: Pierre Tomon <pierretom+12@ik.me>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Pierre Tomon <pierretom+12@ik.me>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening fixes from Kees Cook:
- scsi: mpt3sas: Avoid possible run-time warning with long manufacturer
strings
- mailmap: update entry for Kees Cook
- kunit/fortify: Remove __kmalloc_node() test
* tag 'hardening-v6.10-rc2-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
kunit/fortify: Remove __kmalloc_node() test
mailmap: update entry for Kees Cook
scsi: mpt3sas: Avoid possible run-time warning with long manufacturer strings
|
|
The prior strscpy() replacement of strncpy() here expected the
manufacture_reply strings to be NUL-terminated, but it is possible
they are not, as the code pattern here shows, e.g., edev->vendor_id
being exactly 1 character larger than manufacture_reply->vendor_id,
and the replaced strncpy() was copying only up to the size of the
source character array. Replace this with memtostr(), which is the
unambiguous way to convert a maybe not-NUL-terminated character array
into a NUL-terminated string.
Fixes: b7e9712a02e8 ("scsi: mpt3sas: Replace deprecated strncpy() with strscpy()")
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Marco Patalano <mpatalan@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240410023155.2100422-3-keescook@chromium.org
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
Pull in remaining commits from 6.10/scsi-queue.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
sd can set a max_sectors value that is lower than the max_hw_sectors
limit based on the block limits VPD page. While this is rather unusual,
it used to work until the max_user_sectors field was split out to cleanly
deal with conflicting hardware and user limits when the hardware limit
changes. Also set max_user_sectors to ensure the limit can properly be
stacked.
Fixes: 4f563a64732d ("block: add a max_user_discard_sectors queue limit")
Reported-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mike Snitzer <snitzer@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240523182618.602003-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Peter Schneider reported that a system would no longer boot after
updating to 6.8.4. Peter bisected the issue and identified commit
b5fc07a5fb56 ("scsi: core: Consult supported VPD page list prior to
fetching page") as being the culprit.
Turns out the enclosure device in Peter's system reports a byteswapped
page length for VPD page 0. It reports "02 00" as page length instead
of "00 02". This causes us to attempt to access 516 bytes (page length
+ header) of information despite only 2 pages being present.
Limit the page search scope to the size of our VPD buffer to guard
against devices returning a larger page count than requested.
Link: https://lore.kernel.org/r/20240521023040.2703884-1-martin.petersen@oracle.com
Fixes: b5fc07a5fb56 ("scsi: core: Consult supported VPD page list prior to fetching page")
Cc: stable@vger.kernel.org
Reported-by: Peter Schneider <pschneider1968@googlemail.com>
Closes: https://lore.kernel.org/all/eec6ebbf-061b-4a7b-96dc-ea748aa4d035@googlemail.com/
Tested-by: Peter Schneider <pschneider1968@googlemail.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull virtio updates from Michael Tsirkin:
"Several new features here:
- virtio-net is finally supported in vduse
- virtio (balloon and mem) interaction with suspend is improved
- vhost-scsi now handles signals better/faster
And fixes, cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (48 commits)
virtio-pci: Check if is_avq is NULL
virtio: delete vq in vp_find_vqs_msix() when request_irq() fails
MAINTAINERS: add Eugenio Pérez as reviewer
vhost-vdpa: Remove usage of the deprecated ida_simple_xx() API
vp_vdpa: don't allocate unused msix vectors
sound: virtio: drop owner assignment
fuse: virtio: drop owner assignment
scsi: virtio: drop owner assignment
rpmsg: virtio: drop owner assignment
nvdimm: virtio_pmem: drop owner assignment
wifi: mac80211_hwsim: drop owner assignment
vsock/virtio: drop owner assignment
net: 9p: virtio: drop owner assignment
net: virtio: drop owner assignment
net: caif: virtio: drop owner assignment
misc: nsm: drop owner assignment
iommu: virtio: drop owner assignment
drm/virtio: drop owner assignment
gpio: virtio: drop owner assignment
firmware: arm_scmi: virtio: drop owner assignment
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the small set of driver core and kernfs changes for 6.10-rc1.
Nothing major here at all, just a small set of changes for some driver
core apis, and minor fixups. Included in here are:
- sysfs_bin_attr_simple_read() helper added and used
- device_show_string() helper added and used
All usages of these were acked by the various maintainers. Also in
here are:
- kernfs minor cleanup
- removed unused functions
- typo fix in documentation
- pay attention to sysfs_create_link() failures in module.c finally
All of these have been in linux-next for a very long time with no
reported problems"
* tag 'driver-core-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
device property: Fix a typo in the description of device_get_child_node_count()
kernfs: mount: Remove unnecessary ‘NULL’ values from knparent
scsi: Use device_show_string() helper for sysfs attributes
platform/x86: Use device_show_string() helper for sysfs attributes
perf: Use device_show_string() helper for sysfs attributes
IB/qib: Use device_show_string() helper for sysfs attributes
hwmon: Use device_show_string() helper for sysfs attributes
driver core: Add device_show_string() helper for sysfs attributes
treewide: Use sysfs_bin_attr_simple_read() helper
sysfs: Add sysfs_bin_attr_simple_read() helper
module: don't ignore sysfs_create_link() failures
driver core: Remove unused platform_notify, platform_notify_remove
|
|
virtio core already sets the .owner, so driver does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Message-Id: <20240331-module-owner-virtio-v2-23-98f04bfaf46a@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Skip E820 checks for MCFG ECAM regions for new (2016+) machines,
since there's no requirement to describe them in E820 and some
platforms require ECAM to work (Bjorn Helgaas)
- Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more specific (Damien
Le Moal)
- Remove last user and pci_enable_device_io() (Heiner Kallweit)
- Wait for Link Training==0 to avoid possible race (Ilpo Järvinen)
- Skip waiting for devices that have been disconnected while
suspended (Ilpo Järvinen)
- Clear Secondary Status errors after enumeration since Master Aborts
and Unsupported Request errors are an expected part of enumeration
(Vidya Sagar)
MSI:
- Remove unused IMS (Interrupt Message Store) support (Bjorn Helgaas)
Error handling:
- Mask Genesys GL975x SD host controller Replay Timer Timeout
correctable errors caused by a hardware defect; the errors cause
interrupts that prevent system suspend (Kai-Heng Feng)
- Fix EDR-related _DSM support, which previously evaluated revision 5
but assumed revision 6 behavior (Kuppuswamy Sathyanarayanan)
ASPM:
- Simplify link state definitions and mask calculation (Ilpo
Järvinen)
Power management:
- Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports, where BIOS
apparently doesn't know how to put them back in D0 (Mario
Limonciello)
CXL:
- Support resetting CXL devices; special handling required because
CXL Ports mask Secondary Bus Reset by default (Dave Jiang)
DOE:
- Support DOE Discovery Version 2 (Alexey Kardashevskiy)
Endpoint framework:
- Set endpoint BAR to be 64-bit if the driver says that's all the
device supports, in addition to doing so if the size is >2GB
(Niklas Cassel)
- Simplify endpoint BAR allocation and setting interfaces (Niklas
Cassel)
Cadence PCIe controller driver:
- Drop DT binding redundant msi-parent and pci-bus.yaml (Krzysztof
Kozlowski)
Cadence PCIe endpoint driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
Freescale Layerscape PCIe controller driver:
- Convert DT binding to YAML (Frank Li)
MediaTek MT7621 PCIe controller driver:
- Add DT binding missing 'reg' property for child Root Ports
(Krzysztof Kozlowski)
- Fix theoretical string truncation in PHY name (Sergio Paracuellos)
NVIDIA Tegra194 PCIe controller driver:
- Return success for endpoint probe instead of falling through to the
failure path (Vidya Sagar)
Renesas R-Car PCIe controller driver:
- Add DT binding missing IOMMU properties (Geert Uytterhoeven)
- Add DT binding R-Car V4H compatible for host and endpoint mode
(Yoshihiro Shimoda)
Rockchip PCIe controller driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
- Add DT binding missing maxItems to ep-gpios (Krzysztof Kozlowski)
- Set the Subsystem Vendor ID, which was previously zero because it
was masked incorrectly (Rick Wertenbroek)
Synopsys DesignWare PCIe controller driver:
- Restructure DBI register access to accommodate devices where this
requires Refclk to be active (Manivannan Sadhasivam)
- Remove the deinit() callback, which was only need by the
pcie-rcar-gen4, and do it directly in that driver (Manivannan
Sadhasivam)
- Add dw_pcie_ep_cleanup() so drivers that support PERST# can clean
up things like eDMA (Manivannan Sadhasivam)
- Rename dw_pcie_ep_exit() to dw_pcie_ep_deinit() to make it parallel
to dw_pcie_ep_init() (Manivannan Sadhasivam)
- Rename dw_pcie_ep_init_complete() to dw_pcie_ep_init_registers() to
reflect the actual functionality (Manivannan Sadhasivam)
- Call dw_pcie_ep_init_registers() directly from all the glue
drivers, not just those that require active Refclk from the host
(Manivannan Sadhasivam)
- Remove the "core_init_notifier" flag, which was an obscure way for
glue drivers to indicate that they depend on Refclk from the host
(Manivannan Sadhasivam)
TI J721E PCIe driver:
- Add DT binding J784S4 SoC Device ID (Siddharth Vadapalli)
- Add DT binding J722S SoC support (Siddharth Vadapalli)
TI Keystone PCIe controller driver:
- Add DT binding missing num-viewport, phys and phy-name properties
(Jan Kiszka)
Miscellaneous:
- Constify and annotate with __ro_after_init (Heiner Kallweit)
- Convert DT bindings to YAML (Krzysztof Kozlowski)
- Check for kcalloc() failure in of_pci_prop_intr_map() (Duoming
Zhou)"
* tag 'pci-v6.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits)
PCI: Do not wait for disconnected devices when resuming
x86/pci: Skip early E820 check for ECAM region
PCI: Remove unused pci_enable_device_io()
ata: pata_cs5520: Remove unnecessary call to pci_enable_device_io()
PCI: Update pci_find_capability() stub return types
PCI: Remove PCI_IRQ_LEGACY
scsi: vmw_pvscsi: Do not use PCI_IRQ_LEGACY instead of PCI_IRQ_LEGACY
scsi: pmcraid: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: mpt3sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: megaraid_sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: ipr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: hpsa: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: arcmsr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
wifi: rtw89: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
dt-bindings: PCI: rockchip,rk3399-pcie: Add missing maxItems to ep-gpios
Revert "genirq/msi: Provide constants for PCI/IMS support"
Revert "x86/apic/msi: Enable PCI/IMS"
Revert "iommu/vt-d: Enable PCI/IMS"
Revert "iommu/amd: Enable PCI/IMS"
Revert "PCI/MSI: Provide IMS (Interrupt Message Store) support"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull bdev bd_inode updates from Al Viro:
"Replacement of bdev->bd_inode with sane(r) set of primitives by me and
Yu Kuai"
* tag 'pull-bd_inode-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RIP ->bd_inode
dasd_format(): killing the last remaining user of ->bd_inode
nilfs_attach_log_writer(): use ->bd_mapping->host instead of ->bd_inode
block/bdev.c: use the knowledge of inode/bdev coallocation
gfs2: more obvious initializations of mapping->host
fs/buffer.c: massage the remaining users of ->bd_inode to ->bd_mapping
blk_ioctl_{discard,zeroout}(): we only want ->bd_inode->i_mapping here...
grow_dev_folio(): we only want ->bd_inode->i_mapping there
use ->bd_mapping instead of ->bd_inode->i_mapping
block_device: add a pointer to struct address_space (page cache of bdev)
missing helpers: bdev_unhash(), bdev_drop()
block: move two helpers into bdev.c
block2mtd: prevent direct access of bd_inode
dm-vdo: use bdev_nr_bytes(bdev) instead of i_size_read(bdev->bd_inode)
blkdev_write_iter(): saner way to get inode and bdev
bcachefs: remove dead function bdev_sectors()
ext4: remove block_device_ejected()
erofs_buf: store address_space instead of inode
erofs: switch erofs_bread() to passing offset instead of block number
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull mm updates from Andrew Morton:
"The usual shower of singleton fixes and minor series all over MM,
documented (hopefully adequately) in the respective changelogs.
Notable series include:
- Lucas Stach has provided some page-mapping cleanup/consolidation/
maintainability work in the series "mm/treewide: Remove pXd_huge()
API".
- In the series "Allow migrate on protnone reference with
MPOL_PREFERRED_MANY policy", Donet Tom has optimized mempolicy's
MPOL_PREFERRED_MANY mode, yielding almost doubled performance in
one test.
- In their series "Memory allocation profiling" Kent Overstreet and
Suren Baghdasaryan have contributed a means of determining (via
/proc/allocinfo) whereabouts in the kernel memory is being
allocated: number of calls and amount of memory.
- Matthew Wilcox has provided the series "Various significant MM
patches" which does a number of rather unrelated things, but in
largely similar code sites.
- In his series "mm: page_alloc: freelist migratetype hygiene"
Johannes Weiner has fixed the page allocator's handling of
migratetype requests, with resulting improvements in compaction
efficiency.
- In the series "make the hugetlb migration strategy consistent"
Baolin Wang has fixed a hugetlb migration issue, which should
improve hugetlb allocation reliability.
- Liu Shixin has hit an I/O meltdown caused by readahead in a
memory-tight memcg. Addressed in the series "Fix I/O high when
memory almost met memcg limit".
- In the series "mm/filemap: optimize folio adding and splitting"
Kairui Song has optimized pagecache insertion, yielding ~10%
performance improvement in one test.
- Baoquan He has cleaned up and consolidated the early zone
initialization code in the series "mm/mm_init.c: refactor
free_area_init_core()".
- Baoquan has also redone some MM initializatio code in the series
"mm/init: minor clean up and improvement".
- MM helper cleanups from Christoph Hellwig in his series "remove
follow_pfn".
- More cleanups from Matthew Wilcox in the series "Various
page->flags cleanups".
- Vlastimil Babka has contributed maintainability improvements in the
series "memcg_kmem hooks refactoring".
- More folio conversions and cleanups in Matthew Wilcox's series:
"Convert huge_zero_page to huge_zero_folio"
"khugepaged folio conversions"
"Remove page_idle and page_young wrappers"
"Use folio APIs in procfs"
"Clean up __folio_put()"
"Some cleanups for memory-failure"
"Remove page_mapping()"
"More folio compat code removal"
- David Hildenbrand chipped in with "fs/proc/task_mmu: convert
hugetlb functions to work on folis".
- Code consolidation and cleanup work related to GUP's handling of
hugetlbs in Peter Xu's series "mm/gup: Unify hugetlb, part 2".
- Rick Edgecombe has developed some fixes to stack guard gaps in the
series "Cover a guard gap corner case".
- Jinjiang Tu has fixed KSM's behaviour after a fork+exec in the
series "mm/ksm: fix ksm exec support for prctl".
- Baolin Wang has implemented NUMA balancing for multi-size THPs.
This is a simple first-cut implementation for now. The series is
"support multi-size THP numa balancing".
- Cleanups to vma handling helper functions from Matthew Wilcox in
the series "Unify vma_address and vma_pgoff_address".
- Some selftests maintenance work from Dev Jain in the series
"selftests/mm: mremap_test: Optimizations and style fixes".
- Improvements to the swapping of multi-size THPs from Ryan Roberts
in the series "Swap-out mTHP without splitting".
- Kefeng Wang has significantly optimized the handling of arm64's
permission page faults in the series
"arch/mm/fault: accelerate pagefault when badaccess"
"mm: remove arch's private VM_FAULT_BADMAP/BADACCESS"
- GUP cleanups from David Hildenbrand in "mm/gup: consistently call
it GUP-fast".
- hugetlb fault code cleanups from Vishal Moola in "Hugetlb fault
path to use struct vm_fault".
- selftests build fixes from John Hubbard in the series "Fix
selftests/mm build without requiring "make headers"".
- Memory tiering fixes/improvements from Ho-Ren (Jack) Chuang in the
series "Improved Memory Tier Creation for CPUless NUMA Nodes".
Fixes the initialization code so that migration between different
memory types works as intended.
- David Hildenbrand has improved follow_pte() and fixed an errant
driver in the series "mm: follow_pte() improvements and acrn
follow_pte() fixes".
- David also did some cleanup work on large folio mapcounts in his
series "mm: mapcount for large folios + page_mapcount() cleanups".
- Folio conversions in KSM in Alex Shi's series "transfer page to
folio in KSM".
- Barry Song has added some sysfs stats for monitoring multi-size
THP's in the series "mm: add per-order mTHP alloc and swpout
counters".
- Some zswap cleanups from Yosry Ahmed in the series "zswap
same-filled and limit checking cleanups".
- Matthew Wilcox has been looking at buffer_head code and found the
documentation to be lacking. The series is "Improve buffer head
documentation".
- Multi-size THPs get more work, this time from Lance Yang. His
series "mm/madvise: enhance lazyfreeing with mTHP in madvise_free"
optimizes the freeing of these things.
- Kemeng Shi has added more userspace-visible writeback
instrumentation in the series "Improve visibility of writeback".
- Kemeng Shi then sent some maintenance work on top in the series
"Fix and cleanups to page-writeback".
- Matthew Wilcox reduces mmap_lock traffic in the anon vma code in
the series "Improve anon_vma scalability for anon VMAs". Intel's
test bot reported an improbable 3x improvement in one test.
- SeongJae Park adds some DAMON feature work in the series
"mm/damon: add a DAMOS filter type for page granularity access recheck"
"selftests/damon: add DAMOS quota goal test"
- Also some maintenance work in the series
"mm/damon/paddr: simplify page level access re-check for pageout"
"mm/damon: misc fixes and improvements"
- David Hildenbrand has disabled some known-to-fail selftests ni the
series "selftests: mm: cow: flag vmsplice() hugetlb tests as
XFAIL".
- memcg metadata storage optimizations from Shakeel Butt in "memcg:
reduce memory consumption by memcg stats".
- DAX fixes and maintenance work from Vishal Verma in the series
"dax/bus.c: Fixups for dax-bus locking""
* tag 'mm-stable-2024-05-17-19-19' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (426 commits)
memcg, oom: cleanup unused memcg_oom_gfp_mask and memcg_oom_order
selftests/mm: hugetlb_madv_vs_map: avoid test skipping by querying hugepage size at runtime
mm/hugetlb: add missing VM_FAULT_SET_HINDEX in hugetlb_wp
mm/hugetlb: add missing VM_FAULT_SET_HINDEX in hugetlb_fault
selftests: cgroup: add tests to verify the zswap writeback path
mm: memcg: make alloc_mem_cgroup_per_node_info() return bool
mm/damon/core: fix return value from damos_wmark_metric_value
mm: do not update memcg stats for NR_{FILE/SHMEM}_PMDMAPPED
selftests: cgroup: remove redundant enabling of memory controller
Docs/mm/damon/maintainer-profile: allow posting patches based on damon/next tree
Docs/mm/damon/maintainer-profile: change the maintainer's timezone from PST to PT
Docs/mm/damon/design: use a list for supported filters
Docs/admin-guide/mm/damon/usage: fix wrong schemes effective quota update command
Docs/admin-guide/mm/damon/usage: fix wrong example of DAMOS filter matching sysfs file
selftests/damon: classify tests for functionalities and regressions
selftests/damon/_damon_sysfs: use 'is' instead of '==' for 'None'
selftests/damon/_damon_sysfs: find sysfs mount point from /proc/mounts
selftests/damon/_damon_sysfs: check errors from nr_schemes file reads
mm/damon/core: initialize ->esz_bp from damos_quota_init_priv()
selftests/damon: add a test for DAMOS quota goal
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Avoid 'constexpr', which is a keyword in C23
- Allow 'dtbs_check' and 'dt_compatible_check' run independently of
'dt_binding_check'
- Fix weak references to avoid GOT entries in position-independent code
generation
- Convert the last use of 'optional' property in arch/sh/Kconfig
- Remove support for the 'optional' property in Kconfig
- Remove support for Clang's ThinLTO caching, which does not work with
the .incbin directive
- Change the semantics of $(src) so it always points to the source
directory, which fixes Makefile inconsistencies between upstream and
downstream
- Fix 'make tar-pkg' for RISC-V to produce a consistent package
- Provide reasonable default coverage for objtool, sanitizers, and
profilers
- Remove redundant OBJECT_FILES_NON_STANDARD, KASAN_SANITIZE, etc.
- Remove the last use of tristate choice in drivers/rapidio/Kconfig
- Various cleanups and fixes in Kconfig
* tag 'kbuild-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (46 commits)
kconfig: use sym_get_choice_menu() in sym_check_prop()
rapidio: remove choice for enumeration
kconfig: lxdialog: remove initialization with A_NORMAL
kconfig: m/nconf: merge two item_add_str() calls
kconfig: m/nconf: remove dead code to display value of bool choice
kconfig: m/nconf: remove dead code to display children of choice members
kconfig: gconf: show checkbox for choice correctly
kbuild: use GCOV_PROFILE and KCSAN_SANITIZE in scripts/Makefile.modfinal
Makefile: remove redundant tool coverage variables
kbuild: provide reasonable defaults for tool coverage
modules: Drop the .export_symbol section from the final modules
kconfig: use menu_list_for_each_sym() in sym_check_choice_deps()
kconfig: use sym_get_choice_menu() in conf_write_defconfig()
kconfig: add sym_get_choice_menu() helper
kconfig: turn defaults and additional prompt for choice members into error
kconfig: turn missing prompt for choice members into error
kconfig: turn conf_choice() into void function
kconfig: use linked list in sym_set_changed()
kconfig: gconf: use MENU_CHANGED instead of SYMBOL_CHANGED
kconfig: gconf: remove debug code
...
|
|
In pvscsi_probe(), initialize irq_flag using PCI_IRQ_ALL_TYPES to remove
the use of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-28-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use the macro PCI_IRQ_INTX instead of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-27-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use the macro PCI_IRQ_INTX instead of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-26-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use the macro PCI_IRQ_INTX instead of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-25-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use the macro PCI_IRQ_INTX instead of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-24-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use the macro PCI_IRQ_INTX instead of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-23-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
|