| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When spi-cadence is configured as a slave, it requires the SPI refclk to
detect the synchronization start condition while communicating with the
master. However, the spi-cadence driver never enables the SPI refclk in
slave mode, causing the refclk to remain disabled if the
"clk_ignore_unused" kernel parameter is not passed through bootargs.
As a result, the slave cannot detect data sent by the master, leading to
communication failure. Update driver to enable the SPI refclk in both
master and slave configurations.
Fixes: b1b90514eaa3 ("spi: spi-cadence: Add support for Slave mode")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://msgid.link/r/20240617153837.29861-1-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add optional reset control support for spi-cadence to properly bring
the SPI device into an operating condition.
Co-developed-by: Eng Lee Teh <englee.teh@starfivetech.com>
Signed-off-by: Eng Lee Teh <englee.teh@starfivetech.com>
Co-developed-by: Ley Foon Tan <leyfoon.tan@starfivetech.com>
Signed-off-by: Ley Foon Tan <leyfoon.tan@starfivetech.com>
Signed-off-by: Ji Sheng Teoh <jisheng.teoh@starfivetech.com>
Link: https://msgid.link/r/20240508054728.1751162-2-jisheng.teoh@starfivetech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the existing implementation, when executing interleaved write and read
operations in the ISR for a transfer length greater than the FIFO size,
the TXFIFO write precedes the RXFIFO read. Consequently, the initially
received data in the RXFIFO is pushed out and lost, leading to a failure
in data integrity. To address this issue, reverse the order of interleaved
operations and conduct the RXFIFO read followed by the TXFIFO write.
Fixes: 6afe2ae8dc48 ("spi: spi-cadence: Interleave write of TX and read of RX FIFO")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://msgid.link/r/20231218090652.18403-1-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The commit 855a40cd8ccc ("spi: cadence: Add SPI transfer delays") adds a
delay after each transfer into the driver's transfer_one(). However,
the delay is already done in SPI core. So this commit unnecessarily
doubles the delay amount. Revert this commit.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Link: https://lore.kernel.org/r/20231206145233.74982-1-namcao@linutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since commit 7ef9651e9792 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20230823133938.1359106-9-lizetao1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"There's been quite a lot of generic activity here, but more
administrative than featuers. We also have a bunch of new drivers,
including one that's part of a MFD so we pulled in the core parts of
that:
- Lots of work from both Yang Yingliang and Andy Shevchenko on moving
to host/device/controller based terminology for devices.
- QuadSPI SPI support for Allwinner sun6i.
- New device support Cirrus Logic CS43L43, Longsoon, Qualcomm GENI
QuPv3 and StarFive JH7110 QSPI"
* tag 'spi-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (151 commits)
spi: at91-usart: Use PTR_ERR_OR_ZERO() to simplify code
spi: spi-sn-f-ospi: switch to use modern name
spi: sifive: switch to use modern name
spi: sh: switch to use modern name
spi: sh-sci: switch to use modern name
spi: sh-msiof: switch to use modern name
spi: sh-hspi: switch to use modern name
spi: sc18is602: switch to use modern name
spi: s3c64xx: switch to use modern name
spi: rzv2m-csi: switch to use devm_spi_alloc_host()
spi: rspi: switch to use spi_alloc_host()
spi: rockchip: switch to use modern name
spi: rockchip-sfc: switch to use modern name
spi: realtek-rtl: switch to use devm_spi_alloc_host()
spi: rb4xx: switch to use modern name
spi: qup: switch to use modern name
spi: spi-qcom-qspi: switch to use modern name
spi: pxa2xx: switch to use modern name
spi: ppc4xx: switch to use modern name
spi: spl022: switch to use modern name
...
|
|
Remove 10us delay in cdns_spi_process_fifo() (called from cdns_spi_irq())
to fix data corruption issue on Master side when this driver
configured in Slave mode, as Slave is failed to prepare the date
on time due to above delay.
Add 10us delay before processing the RX FIFO as TX empty doesn't
guarantee valid data in RX FIFO.
Signed-off-by: Srinivas Goud <srinivas.goud@amd.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1692610216-217644-1-git-send-email-srinivas.goud@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Yang Yingliang <yangyingliang@huawei.com>:
After introducing devm_spi_alloc_host/spi_alloc_host(), the legacy
named function devm_spi_alloc_master/spi_alloc_master() can be replaced.
And also change other legacy name master/slave to modern name host/target
or controller.
|
|
It is not possible for platform_get_irq() to return 0. Use the
return value from platform_get_irq().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> #
Link: https://lore.kernel.org/r/20230802093238.975906-1-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Change legacy name master/slave to modern name host/target or controller.
No functional changed.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20230728093221.3312026-13-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The function no longer returns a value, synchronize the comments.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712064832.67091-1-frank.li@vivo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Get the fixes into CI for development.
|
|
Add the missing kernel documentation to silence the build warning.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230523090124.3132-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When working in slave mode it seems the timing is exceedingly tight.
The TX FIFO can never empty, because the master is driving the clock so
zeros would be sent for those bytes where the FIFO is empty.
Return to interleaving the writing of the TX FIFO and the reading
of the RX FIFO to try to ensure the data is available when required.
Fixes: a84c11e16dc2 ("spi: spi-cadence: Avoid read of RX FIFO before its ready")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230518093927.711358-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit b1b90514eaa3 ("spi: spi-cadence: Add support for Slave mode")
updated the code to trigger the IRQ when the FIFO was half empty,
overlapping filling more data into the FIFO and sending what is left.
This appears to cause regressions on the Zynq 7000, for transactions
longer than the FIFO size, below that no overlapping occurs.
It would appear from my testing that any attempt to put new data into
the FIFO whilst data is still transmitting causes data corruption
on both send and receive. If I am reading the commit message right
on commit 49530e641178 ("spi: cadence: Add usleep_range() for
cdns_spi_fill_tx_fifo()"), that would also seem to imply this is the
case.
On the assumption that this isn't an issue on the platform
the original slave mode support was added for, update the
cdns_transfer_one to only set the watermark to 50% of the FIFO size
when in slave mode. There by retaining the new behaviour for slave
mode but reverting to the older behaviour when the SPI is used a
master.
Fixes: b1b90514eaa3 ("spi: spi-cadence: Add support for Slave mode")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230509164153.3907694-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
Recent changes to cdns_spi_irq introduced some issues.
Firstly, when writing the end of a longer transaction, the code in
cdns_spi_irq will write data into the TX FIFO, then immediately
fall into the if (!xspi->tx_bytes) path and attempt to read data
from the RX FIFO. However this required waiting for the TX FIFO to
empty before the RX data was ready.
Secondly, the variable trans_cnt is now rather inaccurately named
since in cases, where the watermark is set to 1, trans_cnt will be
1 but the count of bytes transferred would be much longer.
Finally, when setting up the transaction we set the watermark to 50%
of the FIFO if the transaction is great than 50% of the FIFO. However,
there is no need to split a tranaction that is smaller than the
whole FIFO, so anything up to the FIFO size can be done in a single
transaction.
Tidy up the code a little, to avoid repeatedly calling
cdns_spi_read_rx_fifo with a count of 1, and correct the three issues
noted above.
Fixes: b1b90514eaa3 ("spi: spi-cadence: Add support for Slave mode")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230509164153.3907694-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
Currently SPI Cadence controller works only in Master mode.
Updated interrupt handler for Full duplex transfer in Slave mode.
Interrupt handler rely on the TX empty interrupt even for Slave mode
transfer due to below HW limitation.
HW limitation:
AR 65885 - SPI Controller Might Not Update RX_NEMPTY Flag, Showing
Incorrect Status Of The Receive FIFO
SPI Slave mode works in the following manner:
1. One transfer can be finished only after all transfer->len
data been transferred to master device.
2. Slave device only accepts transfer->len data. Any data longer
than this from master device will be dropped. Any data shorter than
this from master will cause SPI to be stuck due to the above behavior.
3. The stale data present in RXFIFO will be dropped in unprepared
hardware transfer function.
Signed-off-by: Srinivas Goud <srinivas.goud@amd.com>
Link: https://lore.kernel.org/r/1681825625-10265-3-git-send-email-srinivas.goud@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Replace spi_master structure with spi_controller structure.
spi_controller structure provides interface support for
both SPI master and slave controller.
Signed-off-by: Srinivas Goud <srinivas.goud@amd.com>
Link: https://lore.kernel.org/r/1681825625-10265-2-git-send-email-srinivas.goud@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
call
Supporting multi-cs in spi drivers would require the chip_select & cs_gpiod
members of struct spi_device to be an array. But changing the type of these
members to array would break the spi driver functionality. To make the
transition smoother introduced four new APIs to get/set the
spi->chip_select & spi->cs_gpiod and replaced all spi->chip_select and
spi->cs_gpiod references with get or set API calls.
While adding multi-cs support in further patches the chip_select & cs_gpiod
members of the spi_device structure would be converted to arrays & the
"idx" parameter of the APIs would be used as array index i.e.,
spi->chip_select[idx] & spi->cs_gpiod[idx] respectively.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Acked-by: Heiko Stuebner <heiko@sntech.de> # Rockchip drivers
Reviewed-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org> # Aspeed driver
Reviewed-by: Dhruva Gole <d-gole@ti.com> # SPI Cadence QSPI
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> # spi-stm32-qspi
Acked-by: William Zhang <william.zhang@broadcom.com> # bcm63xx-hsspi driver
Reviewed-by: Serge Semin <fancer.lancer@gmail.com> # DW SSI part
Link: https://lore.kernel.org/r/167847070432.26.15076794204368669839@mailman-core.alsa-project.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-17-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix SPI NO Slave Select macro definition, when all the SPI CS bits
are high which means no slave is selected.
Fixes: 21b511ddee09 ("spi: spi-cadence: Fix SPI CS gets toggling sporadically")
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20220713164529.28444-1-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The depth of the transmit FIFO for the Cadence SPI controller is currently
hardcoded to 128. But the depth is a synthesis configuration parameter of
the core and can vary between different SoCs.
If the configured FIFO size is less than 128 the driver will busy loop in
the cdns_spi_fill_tx_fifo() function waiting for FIFO space to become
available.
Depending on the length and speed of the transfer it can spin for a
significant amount of time. The cdns_spi_fill_tx_fifo() function is called
from the drivers interrupt handler, so it can leave interrupts disabled for
a prolonged amount of time.
In addition the read FIFO will also overflow and data will be discarded.
To avoid this detect the actual size of the FIFO and use that rather than
the hardcoded value.
To detect the FIFO size the FIFO threshold register is used. The register
is sized so that it can hold FIFO size - 1 as its maximum value. Bits that
are not needed to hold the threshold value will always read 0. By writing
0xffff to the register and then reading back the value in the register we
get the FIFO size.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20220527091143.3780378-1-lars@metafoo.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As part of unprepare_transfer_hardware, SPI controller will be disabled
which will indirectly deassert the CS line. This will create a problem
in some of the devices where message will be transferred with
cs_change flag set(CS should not be deasserted).
As per SPI controller implementation, if SPI controller is disabled then
all output enables are inactive and all pins are set to input mode which
means CS will go to default state high(deassert). This leads to an issue
when core explicitly ask not to deassert the CS (cs_change = 1). This
patch fix the above issue by checking the Slave select status bits from
configuration register before disabling the SPI.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20220606062525.18447-1-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Data type of status variable, that hold the return value of the ISR,
should be irqreturn_t & not u32. This patch updates status variable type
to irqreturn_t.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20220512145025.20205-1-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Kernel function name don't match with function name.
Error log:
drivers/spi/spi-cadence.c:661: warning: expecting prototype for
cdns_spi_runtime_resume(). Prototype was for cnds_runtime_resume() instead
drivers/spi/spi-cadence.c:690: warning: expecting prototype for
cdns_spi_runtime_suspend(). Prototype was for cnds_runtime_suspend()
instead
Fixes: d36ccd9f7ea4 ("spi: cadence: Runtime pm adaptation")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20220322150018.12736-1-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The original implementation of RPM handling in probe() was mostly
correct, except it failed to call pm_runtime_get_*() to activate the
hardware. The subsequent fix, 734882a8bf98 ("spi: cadence: Correct
initialisation of runtime PM"), breaks the implementation further,
to the point where the system using this hard IP on ZynqMP hangs on
boot, because it accesses hardware which is gated off.
Undo 734882a8bf98 ("spi: cadence: Correct initialisation of runtime
PM") and instead add missing pm_runtime_get_noresume() and move the
RPM disabling all the way to the end of probe(). That makes ZynqMP
not hang on boot yet again.
Fixes: 734882a8bf98 ("spi: cadence: Correct initialisation of runtime PM")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210716182133.218640-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The issue is that using SPI from a callback under the CCF lock will
deadlock, since this code uses clk_get_rate().
Fixes: c474b38665463 ("spi: Add driver for Cadence SPI controller")
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210114154217.51996-1-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When processing an SPI transfer, honor the delay that might be passed
along with it.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20201009100309.381279-1-daniel@zonque.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The spi cadence driver should support spi-cs-high in mode bits
so that the peripherals that needs the chip select to be high active can
use it. Add the SPI-CS-HIGH flag in the supported mode bits.
Signed-off-by: Shreyas Joshi <shreyas.joshi@biamp.com>
Link: https://lore.kernel.org/r/20200710211655.1564-1-shreyas.joshi@biamp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
To fix a regression on the Cadence SPI driver, this patch reverts
commit 6046f5407ff0 ("spi: cadence: Fix default polarity of native
chipselect").
This patch was not the correct fix for the issue. The SPI framework
calls the set_cs line with the logic level it desires on the chip select
line, as such the old is_high handling was correct. However, this was
broken by the fact that before commit 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") all controllers that offered
the use of a GPIO chip select had SPI_CS_HIGH applied, even for hardware
chip selects. This caused the value passed into the driver to be inverted.
Which unfortunately makes it look like a logical enable the chip select
value.
Since the core was corrected to not unconditionally apply SPI_CS_HIGH,
the Cadence driver, whilst using the hardware chip select, will deselect
the chip select every time we attempt to communicate with the device,
which results in failed communications.
Fixes: 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191126164140.6240-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-9-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-42-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation either version 2 of the
license or at your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170857.824091446@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Cadence controller also supports platforms specifying
native chipselects. When I enforce the use of high CS
for drivers opting in for using GPIO descriptors, I
inadvertedly switched the driver to also use active
high chip select for native chip selects.
Fix this by inverting the logic in the callback for the
native chip select. Rename the parameter from "is_high"
(which is interpreted as being high when 0, which is
confusing, I will not make any drug-related jokes here)
to "enabled" which is more intuitive, especially now that
it is true when CS is supposed to be enabled.
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Fixes: cfeefa79dc37 ("spi: cadence: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently the driver calls pm_runtime_put_autosuspend but without ever
having done a pm_runtime_get, this causes the reference count in the pm
runtime core to become -1. The bad reference count causes the core to
sometimes suspend whilst an active SPI transfer is in progress.
arizona spi0.1: SPI transfer timed out
spi_master spi0: failed to transfer one message from queue
The correct proceedure is to do all the initialisation that requires the
hardware to be powered up before enabling the PM runtime, then enable
the PM runtime having called pm_runtime_set_active to inform it that the
hardware is currently powered up. The core will then power it down at
it's leisure and no explicit pm_runtime_put is required.
Fixes: d36ccd9f7ea4 ("spi: cadence: Runtime pm adaptation")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This converts the Cadence SPI master driver to use GPIO
descriptors for chip select handling.
The Cadence driver was allocating a state container just
to hold the requested GPIO line and contained lots of
polarity inversion code. As this is all handled by gpiolib
and a simple devm_* request in the core, and as the driver
is fully device tree only, most of this code chunk goes
away in favour of central handling. The setup/cleanup
callbacks goes away.
This driver does NOT drive the CS line by setting the
value of the GPIO so it relies on the SPI core to do
this, which should work just fine with the descriptors.
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: Janek Kotas <jank@cadence.com>
Cc: Linuxarm <linuxarm@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
cnds_runtime_resume()
Fix the missing clk_disable_unprepare() before return
from cnds_runtime_resume() in the error handling case.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The path "spi: cadence: Add usleep_range() for
cdns_spi_fill_tx_fifo()" added a usleep_range() function call,
which cannot be used in atomic context.
However the cdns_spi_fill_tx_fifo() function can be called during
an interrupt which may result in a kernel panic:
BUG: scheduling while atomic: grep/561/0x00010002
Modules linked in:
Preemption disabled at:
[<ffffff800858ea28>] wait_for_common+0x48/0x178
CPU: 0 PID: 561 Comm: grep Not tainted 4.17.0 #1
Hardware name: Cadence CSP (DT)
Call trace:
dump_backtrace+0x0/0x198
show_stack+0x14/0x20
dump_stack+0x8c/0xac
__schedule_bug+0x6c/0xb8
__schedule+0x570/0x5d8
schedule+0x34/0x98
schedule_hrtimeout_range_clock+0x98/0x110
schedule_hrtimeout_range+0x10/0x18
usleep_range+0x64/0x98
cdns_spi_fill_tx_fifo+0x70/0xb0
cdns_spi_irq+0xd0/0xe0
__handle_irq_event_percpu+0x9c/0x128
handle_irq_event_percpu+0x34/0x88
handle_irq_event+0x48/0x78
handle_fasteoi_irq+0xbc/0x1b0
generic_handle_irq+0x24/0x38
__handle_domain_irq+0x84/0xf8
gic_handle_irq+0xc4/0x180
This patch replaces the function call with udelay() which can be
used in an atomic context, like an interrupt.
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
|
|
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In case of xspi work in busy condition, may send bytes failed.
once something wrong, spi controller did't work any more
My test found this situation appear in both of read/write process.
so when TX FIFO is full, add one byte delay before send data;
Signed-off-by: sxauwsk <sxauwsk@163.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Context could be lost across the suspend and resume.
Reinit the driver to tide over.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
call pm_runtime_enable after set_active other wise it will
enable clock always.
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This adds support for using GPIOs for chipselects as described by the
default dt-bindings.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The newly added runtime PM support for the cadence spi driver
causes harmless warnings when PM is disabled:
drivers/spi/spi-cadence.c:681:12: warning: 'cnds_runtime_suspend' defined but not used
drivers/spi/spi-cadence.c:652:12: warning: 'cnds_runtime_resume' defined but not used
This adds __maybe_unused annotations to the respective functions
to shut up the warnings, while leaving the code in place for
compile testing and avoiding ugly #ifdefs.
Fixes: d36ccd9f7ea4 ("spi: cadence: Runtime pm adaptation")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
No functional change.
Fixing some style related issues
CHECK: multiple assignments should be avoided
+ new_ctrl_reg = ctrl_reg = cdns_spi_read(xspi, CDNS_SPI_CR);
CHECK: Alignment should match open parenthesis
+static void cdns_spi_config_clock_freq(struct spi_device *spi,
+ struct spi_transfer *transfer)
CHECK: Please use a blank line after function/struct/union/enum declarations
+}
+static int cdns_prepare_message(struct spi_master *master,
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Return the error code for cdns_spi_suspend and cdns_spi_resume.
Also fixes a comment where which claims that the error code is
returned.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Now that the clocks are enabled and disabled per transaction
, remove the clock enable and disable from resume and suspend
hooks.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently the clocks are enabled at probe and disabled
at remove. This patch moves the clock enable to the
start of transaction and disables at the end.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
cdns_spi_chipselect has parameter is_high however the comment
describes it as is_on.
Also fixes the below warning.
drivers/spi/spi-cadence.c:182: warning: No description found for
parameter 'is_high'
drivers/spi/spi-cadence.c:182: warning: Excess function parameter 'is_on'
description in 'cdns_spi_chipselect'
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
