summaryrefslogtreecommitdiff
path: root/drivers/spi/spi-mem.c
AgeCommit message (Collapse)AuthorFilesLines
2022-06-06spi: spi-mem: Fix spi_mem_poll_status()Patrice Chotard1-1/+1
In spi_mem_exec_op(), in case cs_gpiod descriptor is set, exec_op() callback can't be used. The same must be applied in spi_mem_poll_status(), poll_status() callback can't be used, we must use the legacy path using read_poll_timeout(). Tested on STM32mp257c-ev1 specific evaluation board on which a spi-nand was mounted instead of a spi-nor. Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Tested-by: Patrice Chotard <patrice.chotard@foss.st.com> Link: https://lore.kernel.org/r/20220602091022.358127-1-patrice.chotard@foss.st.com Signed-off-by: Mark Brown <broonie@kernel.org>
2022-05-11spi: stm32-qspi: flags management fixesMark Brown1-0/+10
Merge series from patrice.chotard@foss.st.com <patrice.chotard@foss.st.com> Patrice Chotard <patrice.chotard@foss.st.com>: From: Patrice Chotard <patrice.chotard@foss.st.com> This series update flags management in the following cases: - In APM mode, don't take care of TCF and TEF flags - Always check TCF flag in stm32_qspi_wait_cmd() - Don't check BUSY flag when sending new command
2022-04-21spi: spi-mem: check if data buffers are on stackPratyush Yadav1-0/+10
The buffers passed in the data phase must be DMA-able. Programmers often don't realise this requirement and pass in buffers that reside on the stack. This can be hard to spot when reviewing code. Reject ops if their data buffer is on the stack to avoid this. Signed-off-by: Pratyush Yadav <p.yadav@ti.com> Link: https://lore.kernel.org/r/20220420102022.3310970-1-p.yadav@ti.com Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-19spi: spi-cadence-quadspi: using pm_runtime_resume_and_get instead of ↵Minghao Chi1-2/+1
pm_runtime_get_sync Using pm_runtime_resume_and_get is more appropriate for simplifing code Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn> Link: https://lore.kernel.org/r/20220413093656.2538504-1-chi.minghao@zte.com.cn Signed-off-by: Mark Brown <broonie@kernel.org>
2022-03-25Merge tag 'mtd/changes-for-5.18' of ↵Linus Torvalds1-14/+18
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux Pull MTD updates from Miquel Raynal: "There has been a lot of activity in the MTD subsystem recently, with a number of SPI-NOR cleanups as well as the introduction of ECC engines that can be used by SPI controllers (hence a few SPI patches in here). Core MTD changes: - Replace the expert mode symbols with a single helper - Fix misuses of of_match_ptr() - Remove partid and partname debugfs files - tests: Fix eraseblock read speed miscalculation for lower partition sizes - TRX parser: Allow to use on MediaTek MIPS SoCs MTD driver changes: - spear_smi: use GFP_KERNEL - mchp48l640: Add SPI ID table - mchp23k256: Add SPI ID table - blkdevs: Avoid soft lockups with some mtd/spi devices - aspeed-smc: Improve probe resilience Hyperbus changes: - HBMC_AM654 should depend on ARCH_K3 NAND core changes: - ECC: - Add infrastructure to support hardware engines - Add a new helper to retrieve the ECC context - Provide a helper to retrieve a pilelined engine device NAND-ECC changes: - Macronix ECC engine: - Add Macronix external ECC engine support - Support SPI pipelined mode - Make two read-only arrays static const - Fix compile test issue Raw NAND core changes: - Fix misuses of of_match_node() - Rework of_get_nand_bus_width() - Remove of_get_nand_on_flash_bbt() wrapper - Protect access to rawnand devices while in suspend - bindings: Document the wp-gpios property Rax NAND controller driver changes: - atmel: Fix refcount issue in atmel_nand_controller_init - nandsim: - Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern - Merge repeat codes in ns_switch_state - Replace overflow check with kzalloc to single kcalloc - rockchip: Fix platform_get_irq.cocci warning - stm32_fmc2: Add NAND Write Protect support - pl353: Set the nand chip node as the flash node - brcmnand: Fix sparse warnings in bcma_nand - omap_elm: Remove redundant variable 'errors' - gpmi: - Support fast edo timings for mx28 - Validate controller clock rate - Fix controller timings setting - brcmnand: - Add BCMA shim - BCMA controller uses command shift of 0 - Allow platform data instantation - Add platform data structure for BCMA - Allow working without interrupts - Move OF operations out of brcmnand_init_cs() - Avoid pdev in brcmnand_init_cs() - Allow SoC to provide I/O operations - Assign soc as early as possible Onenand changes: - Check for error irq SPI-NAND core changes: - Delay a little bit the dirmap creation - Create direct mapping descriptors for ECC operations SPI-NAND driver changes: - macronix: Use random program load SPI NOR core changes: - Move vendor specific code out of the core into vendor drivers. - Unify all function and object names in the vendor modules. - Make setup() callback optional to improve readability. - Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash declaration. SPI changes: - Macronix SPI controller: - Fix the transmit path - Create a helper to configure the controller before an operation - Create a helper to ease the start of an operation - Add support for direct mapping - Add support for pipelined ECC operations - spi-mem: - Introduce a capability structure - Check the controller extra capabilities - cadence-quadspi/mxic: Provide capability structures - Kill the spi_mem_dtr_supports_op() helper - Add an ecc parameter to the spi_mem_op structure Binding changes: - Dropped mtd/cortina,gemini-flash.txt - Convert BCM47xx partitions to json-schema - Vendor prefixes: Clarify Macronix prefix - SPI NAND: Convert spi-nand description file to yaml - Raw NAND chip: Create a NAND chip description - Raw NAND controller: - Harmonize the property types - Fix a comment in the examples - Fix the reg property description - Describe Macronix NAND ECC engine - Macronix SPI controller: - Document the nand-ecc-engine property - Convert to yaml - The interrupt property is not mandatory" * tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (104 commits) mtd: nand: ecc: mxic: Fix compile test issue mtd: nand: mxic-ecc: make two read-only arrays static const mtd: hyperbus: HBMC_AM654 should depend on ARCH_K3 mtd: core: Remove partid and partname debugfs files dt-bindings: mtd: partitions: convert BCM47xx to the json-schema mtd: tests: Fix eraseblock read speed miscalculation for lower partition sizes mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init mtd: rawnand: rockchip: fix platform_get_irq.cocci warning mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set mtd: spi-nor: renumber flags mtd: spi-nor: slightly change code style in spi_nor_sr_ready() mtd: spi-nor: spansion: rename vendor specific functions and defines mtd: spi-nor: spansion: convert USE_CLSR to a manufacturer flag mtd: spi-nor: move all spansion specifics into spansion.c mtd: spi-nor: spansion: slightly rework control flow in late_init() mtd: spi-nor: micron-st: rename vendor specific functions and defines mtd: spi-nor: micron-st: convert USE_FSR to a manufacturer flag mtd: spi-nor: move all micron-st specifics into micron-st.c mtd: spi-nor: xilinx: correct the debug message mtd: spi-nor: xilinx: rename vendor specific functions and defines ...
2022-02-10spi: spi-mem: Add an ecc parameter to the spi_mem_op structureMiquel Raynal1-0/+5
Soon the SPI-NAND core will need a way to request a SPI controller to enable ECC support for a given operation. This is because of the pipelined integration of certain ECC engines, which are directly managed by the SPI controller itself. Introduce a spi_mem_op additional field for this purpose: ecc. So far this field is left unset and checked to be false by all the SPI controller drivers in their ->supports_op() hook, as they all call spi_mem_default_supports_op(). Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Pratyush Yadav <p.yadav@ti.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-7-miquel.raynal@bootlin.com
2022-02-10spi: spi-mem: Kill the spi_mem_dtr_supports_op() helperMiquel Raynal1-10/+0
Now that spi_mem_default_supports_op() has access to the static controller capabilities (relating to memory operations), and now that these capabilities have been filled by the relevant controllers, there is no need for a specific helper checking only DTR operations, so let's just kill spi_mem_dtr_supports_op() and simply use spi_mem_default_supports_op() instead. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Pratyush Yadav <p.yadav@ti.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-6-miquel.raynal@bootlin.com
2022-02-10spi: spi-mem: Check the controller extra capabilitiesMiquel Raynal1-4/+13
Controllers can now provide a spi-mem capabilities structure. Let's make use of it in spi_mem_controller_default_supports_op(). As we want to check for DTR operations as well as normal operations in a single helper, let's pull the necessary checks from spi_mem_dtr_supports_op() for now. However, because no controller provide these extra capabilities, this change has no effect so far. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Pratyush Yadav <p.yadav@ti.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-3-miquel.raynal@bootlin.com
2022-02-09spi: make remove callback a void functionUwe Kleine-König1-4/+2
The value returned by an spi driver's remove function is mostly ignored. (Only an error message is printed if the value is non-zero that the error is ignored.) So change the prototype of the remove function to return no value. This way driver authors are not tempted to assume that passing an error to the upper layer is a good idea. All drivers are adapted accordingly. There is no intended change of behaviour, all callbacks were prepared to return 0 before. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com> Acked-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Acked-by: Claudius Heine <ch@denx.de> Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com> Acked-by: Łukasz Stelmach <l.stelmach@samsung.com> Acked-by: Lee Jones <lee.jones@linaro.org> Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de Signed-off-by: Mark Brown <broonie@kernel.org>
2021-06-14spi: spi-mem: fix doc warning in spi-mem.cYang Yingliang1-1/+1
Fix the following make W=1 warning: drivers/spi/spi-mem.c:819: warning: expecting prototype for spi_mem_driver_unregister_with_owner(). Prototype was for spi_mem_driver_unregister() instead Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20210601120721.3198488-1-yangyingliang@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-06-03spi: spi-mem: add automatic poll status functionsPatrice Chotard1-0/+86
With STM32 QSPI, it is possible to poll the status register of the device. This could be done to offload the CPU during an operation (erase or program a SPI NAND for example). spi_mem_poll_status API has been added to handle this feature. This new function take care of the offload/non-offload cases. For the non-offload case, use read_poll_timeout() to poll the status in order to release CPU during this phase. For example, previously, when erasing large area, in non-offload case, CPU load can reach ~50%, now it decrease to ~35%. Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://lore.kernel.org/r/20210518162754.15940-2-patrice.chotard@foss.st.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-03-24spi: spi-mem: Fix code indent should use tabs where possibleJay Fang1-3/+3
Fix checkpatch errors: ERROR: code indent should use tabs where possible #624: FILE: spi-mem.c:624: ERROR: code indent should use tabs where possible #626: FILE: spi-mem.c:626: ERROR: code indent should use tabs where possible #627: FILE: spi-mem.c:627: Signed-off-by: Jay Fang <f.fangjian@huawei.com> Link: https://lore.kernel.org/r/1616566602-13894-10-git-send-email-f.fangjian@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-02-11spi: spi-mem: add spi_mem_dtr_supports_op()Pratyush Yadav1-3/+19
spi_mem_default_supports_op() rejects DTR ops by default to ensure that the controller drivers that haven't been updated with DTR support continue to reject them. It also makes sure that controllers that don't support DTR mode at all (which is most of them at the moment) also reject them. This means that controller drivers that want to support DTR mode can't use spi_mem_default_supports_op(). Driver authors have to roll their own supports_op() function and mimic the buswidth checks. See spi-cadence-quadspi.c for example. Or even worse, driver authors might skip it completely or get it wrong. Add spi_mem_dtr_supports_op(). It provides a basic sanity check for DTR ops and performs the buswidth requirement check. Move the logic for checking buswidth in spi_mem_default_supports_op() to a separate function so the logic is not repeated twice. Signed-off-by: Pratyush Yadav <p.yadav@ti.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20210204141218.32229-1-p.yadav@ti.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-01-06spi: spi-mem: Mark dummy transfers by setting dummy_data bitSowjanya Komatineni1-0/+1
This patch marks dummy transfer by setting dummy_data bit to 1. Controllers supporting dummy transfer by hardware use this bit field to skip software transfer of dummy bytes and use hardware dummy bytes transfer. Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Link: https://lore.kernel.org/r/1608585459-17250-6-git-send-email-skomatineni@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-04spi: spi-mem: fix reference leak in spi_mem_access_startZhang Qilong1-0/+1
pm_runtime_get_sync will increment pm usage counter even it failed. Forgetting to pm_runtime_put_noidle will result in reference leak in spi_mem_access_start, so we should fix it. Fixes: f86c24f479530 ("spi: spi-mem: Split spi_mem_exec_op() code") Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com> Link: https://lore.kernel.org/r/20201103140910.3482-1-zhangqilong3@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-02spi: spi-mem: Fix passing zero to 'PTR_ERR' warningYueHaibing1-1/+1
Fix smatch warning: drivers/spi/spi-mem.c:746 spi_mem_probe() warn: passing zero to 'PTR_ERR' Fixes: 5d27a9c8ea9e ("spi: spi-mem: Extend the SPI mem interface to set a custom memory name") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Link: https://lore.kernel.org/r/20201031033042.42892-1-yuehaibing@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-07-14spi: spi-mem: allow specifying a command's extensionPratyush Yadav1-6/+7
In xSPI mode, flashes expect 2-byte opcodes. The second byte is called the "command extension". There can be 3 types of extensions in xSPI: repeat, invert, and hex. When the extension type is "repeat", the same opcode is sent twice. When it is "invert", the second byte is the inverse of the opcode. When it is "hex" an additional opcode byte based is sent with the command whose value can be anything. So, make opcode a 16-bit value and add a 'nbytes', similar to how multiple address widths are handled. Some places use sizeof(op->cmd.opcode). Replace them with op->cmd.nbytes The spi-mxic and spi-zynq-qspi drivers directly use op->cmd.opcode as a buffer. Now that opcode is a 2-byte field, this can result in different behaviour depending on if the machine is little endian or big endian. Extract the opcode in a local 1-byte variable and use that as the buffer instead. Both these drivers would reject multi-byte opcodes in their supports_op() hook anyway, so we only need to worry about single-byte opcodes for now. The above two changes are put in this commit to keep the series bisectable. Signed-off-by: Pratyush Yadav <p.yadav@ti.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Link: https://lore.kernel.org/r/20200623183030.26591-3-p.yadav@ti.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-07-14spi: spi-mem: allow specifying whether an op is DTR or notPratyush Yadav1-0/+3
Each phase is given a separate 'dtr' field so mixed protocols like 4S-4D-4D can be supported. Signed-off-by: Pratyush Yadav <p.yadav@ti.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Link: https://lore.kernel.org/r/20200623183030.26591-2-p.yadav@ti.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-04-23spi: spi-mem: Fix Dual/Quad modes on Octal-capable devicesGeert Uytterhoeven1-4/+6
Currently buswidths 2 and 4 are rejected for a device that advertises Octal capabilities. Allow these buswidths, just like is done for buswidth 2 and Quad-capable devices. Fixes: b12a084c8729ef42 ("spi: spi-mem: add support for octal mode I/O data transfer") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20200416101418.14379-1-geert+renesas@glider.be Signed-off-by: Mark Brown <broonie@kernel.org>
2020-02-28spi: spi-mem: Compute length only when neededTudor Ambarus1-2/+3
When adjust_op_size is defined, len is never used. Move the len computation where it's actually used. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Link: https://lore.kernel.org/r/20200228160735.1565047-1-tudor.ambarus@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-02-17spi: spi-mem: Fix typo, s/fallback/falls backTudor Ambarus1-1/+1
"Fallback" in one word is a noun. "Fall back" is two separate words, a verb and an adverb. Use the latter. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Link: https://lore.kernel.org/r/20200216214012.1106658-1-tudor.ambarus@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org>
2019-11-07spi: spi-mem: fallback to using transfers when CS gpios are usedChris Packham1-1/+1
Devices with chip selects driven via GPIO are not compatible with the spi-mem operations. Fallback to using standard spi transfers when the device is connected with a gpio CS. Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Link: https://lore.kernel.org/r/20191107044235.4864-3-chris.packham@alliedtelesis.co.nz Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-08spi-mem: fix kernel-doc for spi_mem_dirmap_{read|write}()Sergei Shtylyov1-2/+2
The function names in the kernel-doc comments were mistyped, with a word "dirmap" being repeated twice, so fix them. Fixes: aa167f3fed0c ("spi: spi-mem: Add a new API to support direct mapping") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: spi-mem: export spi_mem_default_supports_op()Naga Sureshkumar Relli1-2/+2
Export spi_mem_default_supports_op(), so that controller drivers can use this. spi-mem driver already exports this using EXPORT_SYMBOL, but not declared it in spi-mem.h. This patch declares spi_mem_default_supports_op() in spi-mem.h and also removes the static from the function prototype. Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-02-20Merge branch 'for-5.0' of ↵Mark Brown1-1/+2
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into spi-5.1
2019-01-21spi: spi-mem: Add devm_spi_mem_dirmap_{create,destroy}()Boris Brezillon1-0/+69
Since direct mapping descriptors usually the same lifetime as the SPI MEM device adding devm_ variants of the spi_mem_dirmap_{create,destroy}() should greatly simplify error/remove path of spi-mem drivers making use of the direct mapping API. Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-01-21spi: spi-mem: Fix a memory leak in spi_mem_dirmap_destroy()Boris Brezillon1-0/+2
The dirmap descriptor object allocated in spi_mem_dirmap_create is never freed. Add a kfree(desc) in spi_mem_dirmap_destroy(). Fixes: aa167f3fed0c ("spi: spi-mem: Add a new API to support direct mapping") Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-01-21spi: spi-mem: Fix spi_mem_dirmap_destroy() kerneldocBoris Brezillon1-1/+0
spi_mem_dirmap_destroy() takes a single argument, remove the @info entry in the doc. Fixes: aa167f3fed0c ("spi: spi-mem: Add a new API to support direct mapping") Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-12-20Merge remote-tracking branches 'spi/topic/mem' and 'spi/topic/mtd' into spi-nextMark Brown1-22/+247
2018-12-03spi: spi-mem: add support for octal mode I/O data transferYogesh Narayan Gaur1-1/+8
Add support for octal mode I/O data transfer in spi-mem framework. Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-20spi: spi-mem: Add a new API to support direct mappingBoris Brezillon1-0/+204
Most modern SPI controllers can directly map a SPI memory (or a portion of the SPI memory) in the CPU address space. Most of the time this brings significant performance improvements as it automates the whole process of sending SPI memory operations every time a new region is accessed. This new API allows SPI memory drivers to create direct mappings and then use them to access the memory instead of using spi_mem_exec_op(). Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-20spi: spi-mem: Split spi_mem_exec_op() codeBoris Brezillon1-21/+42
The logic surrounding the ->exec_op() call applies to direct mapping accessors. Move this code to separate functions to avoid duplicating code. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-20spi: spi-mem: Add SPI_MEM_NO_DATA to the spi_mem_data_dir enumBoris Brezillon1-1/+1
When defining spi_mem_op templates we don't necessarily know the size that will be passed when the template is actually used, and basing the supports_op() check on op->data.nbytes to know whether there will be data transferred for a specific operation is this not possible. Add SPI_MEM_NO_DATA to the spi_mem_data_dir enum so that we can base our checks on op->data.dir instead of op->data.nbytes. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-09-28spi: spi-mem: Fix inverted logic in op sanity checkGeert Uytterhoeven1-4/+4
On r8a7791/koelsch: m25p80 spi0.0: error -22 reading 9f m25p80: probe of spi0.0 failed with error -22 Apparently the logic in spi_mem_check_op() is wrong, rejecting the spi-mem operation if any buswidth is valid, instead of invalid. Fixes: 380583227c0c7f52 ("spi: spi-mem: Add extra sanity checks on the op param") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-09-20spi: spi-mem: Add extra sanity checks on the op paramBoris Brezillon1-6/+48
Some combinations are simply not valid and should be rejected before the op is passed to the SPI controller driver. Add an spi_mem_check_op() helper and use it in spi_mem_exec_op() and spi_mem_supports_op() to make sure the spi-mem operation is valid. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-09-10spi: spi-mem: Adjust op len based on message/transfer size limitationsChuanhua Han1-0/+15
We need that to adjust the len of the 2nd transfer (called data in spi-mem) if it's too long to fit in a SPI message or SPI transfer. Fixes: c36ff266dc82 ("spi: Extend the core to ease integration of SPI memory controllers") Cc: <stable@vger.kernel.org> Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-08-02spi: spi-mem: Extend the SPI mem interface to set a custom memory nameFrieder Schrempf1-0/+28
When porting (Q)SPI controller drivers from the MTD layer to the SPI layer, the naming scheme for the memory devices changes. To be able to keep compatibility with the old drivers naming scheme, a name field is added to struct spi_mem and a hook is added to let controller drivers set a custom name for the memory device. Example for the FSL QSPI driver: Name with the old driver: 21e0000.qspi, or with multiple devices: 21e0000.qspi-0, 21e0000.qspi-1, ... Name with the new driver without spi_mem_get_name: spi4.0 Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Frieder Schrempf <frieder.schrempf@exceet.de> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-05-11spi: Extend the core to ease integration of SPI memory controllersBoris Brezillon1-0/+410
Some controllers are exposing high-level interfaces to access various kind of SPI memories. Unfortunately they do not fit in the current spi_controller model and usually have drivers placed in drivers/mtd/spi-nor which are only supporting SPI NORs and not SPI memories in general. This is an attempt at defining a SPI memory interface which works for all kinds of SPI memories (NORs, NANDs, SRAMs). Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de> Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de> Signed-off-by: Mark Brown <broonie@kernel.org>
generated by cgit v1.2.3 (git 2.39.0) at 2024-07-24 08:03:19 +0300