| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Currently the sun8i thermal driver will fail to probe if any of the
thermal zones it is registering fails to register with the thermal core.
Since we currently do not define any trip points for the GPU thermal
zones on at least A64 or H5 this means that we have no thermal support
on these platforms:
[ 1.698703] thermal_sys: Failed to find 'trips' node
[ 1.698707] thermal_sys: Failed to find trip points for thermal-sensor id=1
even though the main CPU thermal zone on both SoCs is fully configured.
This does not seem ideal, while we may not be able to use all the zones
it seems better to have those zones which are usable be operational.
Instead just carry on registering zones if we get any non-deferral
error, allowing use of those zones which are usable.
This means that we also need to update the interrupt handler to not
attempt to notify the core for events on zones which we have not
registered, I didn't see an ability to mask individual interrupts and
I would expect that interrupts would still be indicated in the ISR even
if they were masked.
Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240123-thermal-sun8i-registration-v3-1-3e5771b1bbdd@kernel.org
|
|
Add support for the thermal sensor found in H616 SoCs, is the same as
the H6 thermal sensor controller, but with four sensors.
Also the registers readings are wrong, unless a bit in the first SYS_CFG
register cleared, so set exercise the SRAM regmap to take care of that.
Signed-off-by: Martin Botka <martin.botka@somainline.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240219153639.179814-7-andre.przywara@arm.com
|
|
The Allwinner H616 SoC needs to clear a bit in one register in the SRAM
controller, to report reasonable temperature values. On reset, bit 16 in
register 0x3000000 is set, which leads to the driver reporting
temperatures around 200C. Clearing this bit brings the values down to the
expected range. The BSP code does a one-time write in U-Boot, with a
comment just mentioning the effect on the THS, but offering no further
explanation.
To not rely on firmware to set things up for us, add code that queries
the SRAM controller device via a DT phandle link, then clear just this
single bit.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240219153639.179814-6-andre.przywara@arm.com
|
|
The H616 SoC resembles the H6 thermal sensor controller, with a few
changes like four sensors.
Extend sun50i_h6_ths_calibrate() function to support calibration of
these sensors.
Co-developed-by: Martin Botka <martin.botka@somainline.org>
Signed-off-by: Martin Botka <martin.botka@somainline.org>
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240219153639.179814-5-andre.przywara@arm.com
|
|
So far we were ORing in some "unknown" value into the THS control
register on the Allwinner H6. This part of the register is not explained
in the H6 manual, but the H616 manual details those bits, and on closer
inspection the THS IP blocks in both SoCs seem very close:
- The BSP code for both SoCs writes the same values into THS_CTRL.
- The reset values of at least the first three registers are the same.
Replace the "unknown" value with its proper meaning: "acquire time",
most probably the sample part of the sample & hold circuit of the ADC,
according to its explanation in the H616 manual.
No functional change, just a macro rename and adjustment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240219153639.179814-4-andre.przywara@arm.com
|
|
This patch adds a thermal sensor controller support for the D1/T113s,
which is similar to the one on H6, but with only one sensor and
different scale and offset values.
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20231217210629.131486-3-bigunclemax@gmail.com
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230811194032.4240-1-aboutphysycs@gmail.com
|
|
The sun8i thermal driver reads calibration data via the nvmem API at
startup, updating the device configuration and not referencing the data
again. Rather than explicitly freeing the nvmem data the driver relies
on devm_ to release it, even though the data is never referenced again.
The allocation is still tracked so it's not leaked but this is notable
when looking at the code and is a little wasteful so let's instead
explicitly free the nvmem after we're done with it.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230719-thermal-sun8i-free-nvmem-v1-1-f553d5afef79@kernel.org
|
|
It's redundant, let's remove it.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230626125515.18830-1-frank.li@vivo.com
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-2-frank.li@vivo.com
|
|
Should an error occur after calling sun8i_ths_resource_init() in the probe
function, some resources need to be released, as already done in the
.remove() function.
Switch to the devm_clk_get_enabled() helper and add a new devm_action to
turn sun8i_ths_resource_init() into a fully managed function.
Move the place where reset_control_deassert() is called so that the
recommended order of reset release/clock enable steps is kept.
A64 manual states that:
3.3.6.4. Gating and reset
Make sure that the reset signal has been released before the release of
module clock gating;
This fixes the issue and removes some LoC at the same time.
Fixes: dccc5c3b6f30 ("thermal/drivers/sun8i: Add thermal driver for H6/H5/H3/A64/A83T/R40")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/a8ae84bd2dc4b55fe428f8e20f31438bf8bb6762.1684089931.git.christophe.jaillet@wanadoo.fr
|
|
The devres variant of thermal_add_hwmon_sysfs() only takes the thermal
zone structure pointer as parameter.
Actually, it uses the tz->device to add it in the devres list.
It is preferable to use the device registering the thermal zone
instead of the thermal zone device itself. That prevents the driver
accessing the thermal zone structure internals and it is from my POV
more correct regarding how devm_ is used.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> #amlogic_thermal
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> #sun8i_thermal
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> #MediaTek auxadc
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The thermal zone device structure is exposed to the different drivers
and obviously they access the internals while that should be
restricted to the core thermal code.
In order to self-encapsulate the thermal core code, we need to prevent
the drivers accessing directly the thermal zone structure and provide
accessor functions to deal with.
Use the devdata accessor introduced in the previous patch.
No functional changes intended.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> #R-Car
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> #MediaTek auxadc and lvts
Reviewed-by: Balsam CHIHI <bchihi@baylibre.com> #Mediatek lvts
Reviewed-by: Adam Ward <DLG-Adam.Ward.opensource@dm.renesas.com> #da9062
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com> #spread
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> #sun8i_thermal
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #Broadcom
Reviewed-by: Dhruva Gole <d-gole@ti.com> # K3 bandgap
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de> #rockchip
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> #uniphier
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Use TEMP_CALIB_MASK macro instead of raw number.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230123102319.37710-1-frank.li@vivo.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The thermal OF code has a new API allowing to migrate the OF
initialization to a simpler approach. The ops are no longer device
tree specific and are the generic ones provided by the core code.
Convert the ops to the thermal_zone_device_ops format and use the new
API to register the thermal zone with these generic ops.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linexp.org>
Link: https://lore.kernel.org/r/20220804224349.1926752-9-daniel.lezcano@linexp.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220521111145.81697-36-Julia.Lawall@inria.fr
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
s/calibartion/calibration/
s/undocummented/undocumented/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210305014348.17412-1-unixbhaskar@gmail.com
|
|
The bitmap_* API is the standard way to access data in the bitfield.
So convert irq_ack to return an unsigned long, and make things to use
bitmap API.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201109114624.23035-1-frank@allwinnertech.com
|
|
This patch add thermal sensor controller support for A100,
which is similar to the previous ones.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/48cc75920b5c69027134626157089d8b94942711.1595572867.git.frank@allwinnertech.com
|
|
sun50i_h6_ths_calibrate
For sun50i_h6_ths_calibrate(), the data read from nvmem needs a round of
calculation. On the other hand, the newer SOC may store other data in
the space other than 12bit sensor data. Add mask operation to read data
to avoid conversion error.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/dcf98648c16aff7649ff82438bfce6caae3e176f.1595572867.git.frank@allwinnertech.com
|
|
Expose sun8i thermal as a HWMON device.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191228171904.24618-1-tiny.windzz@gmail.com
|
|
The cp_ft_flag variable is not used after initialization, so delete
it. After that, THS_EFUSE_CP_FT_MASK, THS_EFUSE_CP_FT_BIT and
THS_CALIBRATION_IN_FT are not needed, so delete them.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200112180925.23705-1-tiny.windzz@gmail.com
|
|
sun8i_ths_resource_init
sparse returns a warning:
"drivers/thermal/sun8i_thermal.c:341:60: sparse: sparse: Using plain
integer as NULL pointer".
Fix it by replacing the zero integer by a NULL pointer.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200112171318.23025-1-tiny.windzz@gmail.com
|
|
According to the spec, r40 has 2 thermal sensors.
Sensor0 located in the CPU, another in the GPU.
Fixes: dccc5c3b6f30f ("thermal/drivers/sun8i: Add thermal driver for H6/H5/H3/A64/A83T/R40")
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-on: sun8i-r40-bananapi-m2-ultra
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200106174639.20862-1-tiny.windzz@gmail.com
|
|
This patch adds the support for allwinner thermal sensor, within
allwinner SoC. It will register sensors for thermal framework
and use device tree to bind cooling device.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191219172823.1652600-2-anarsoul@gmail.com
|
