| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Currently after writing to REG_UFS_SYS1CLK_1US a mb() is used to ensure
that write has gone through to the device.
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
https://youtu.be/i6DayghhA8Q?si=MiyxB5cKJXSaoc01&t=1678
Let's do that to ensure the bit hits the device. Because the mb()'s purpose
wasn't to add extra ordering (on top of the ordering guaranteed by
writel()/readl()), it can safely be removed.
Fixes: f06fcc7155dc ("scsi: ufs-qcom: add QUniPro hardware support and power optimizations")
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-2-181252004586@redhat.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently, the reset bit for the UFS provided reset controller (used by its
phy) is written to, and then a mb() happens to try and ensure that hit the
device. Immediately afterwards a usleep_range() occurs.
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
https://youtu.be/i6DayghhA8Q?si=MiyxB5cKJXSaoc01&t=1678
Let's do that to ensure the bit hits the device. By doing so and
guaranteeing the ordering against the immediately following usleep_range(),
the mb() can safely be removed.
Fixes: 81c0fc51b7a7 ("ufs-qcom: add support for Qualcomm Technologies Inc platforms")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-1-181252004586@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"Only a couple of driver updates this time (lpfc and mpt3sas) plus the
usual assorted minor fixes and updates. The major core update is a set
of patches moving retries out of the drivers and into the core"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (84 commits)
scsi: core: Constify the struct device_type usage
scsi: libfc: replace deprecated strncpy() with memcpy()
scsi: lpfc: Replace deprecated strncpy() with strscpy()
scsi: bfa: Fix function pointer type mismatch for state machines
scsi: bfa: Fix function pointer type mismatch for hcb_qe->cbfn
scsi: bfa: Remove additional unnecessary struct declarations
scsi: csiostor: Avoid function pointer casts
scsi: qla1280: Remove redundant assignment to variable 'mr'
scsi: core: Make scsi_bus_type const
scsi: core: Really include kunit tests with SCSI_LIB_KUNIT_TEST
scsi: target: tcm_loop: Make tcm_loop_lld_bus const
scsi: scsi_debug: Make pseudo_lld_bus const
scsi: iscsi: Make iscsi_flashnode_bus const
scsi: fcoe: Make fcoe_bus_type const
scsi: lpfc: Copyright updates for 14.4.0.0 patches
scsi: lpfc: Update lpfc version to 14.4.0.0
scsi: lpfc: Change lpfc_vport load_flag member into a bitmask
scsi: lpfc: Change lpfc_vport fc_flag member into a bitmask
scsi: lpfc: Protect vport fc_nodes list with an explicit spin lock
scsi: lpfc: Change nlp state statistic counters into atomic_t
...
|
|
Switch all the users of the platform MSI domain over to invoke the new
interfaces which branch to the original platform MSI functions when the
irqdomain associated to the caller device does not yet provide MSI parent
functionality.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240127161753.114685-7-apatel@ventanamicro.com
|
|
On sa8775p-ride, probing the HBA will go through the
UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH path although the power info is
the same during the second init.
The REINIT quirk only applies starting with controller v4. For these,
ufs_qcom_get_hs_gear() reads the highest supported gear when setting the
host_params. After the negotiation, if the host and device are on the same
gear, it is the highest gear supported between the two. Skip REINIT to save
some time.
Signed-off-by: Eric Chanudet <echanude@redhat.com>
Link: https://lore.kernel.org/r/20240123192854.1724905-4-echanude@redhat.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The comments that currently are within the hw_ver < 4 conditional are
misleading. They really apply to various branches of the conditionals there
and incorrectly state that the phy_gear value can increase.
Right now the logic is to:
- Default to max supported gear for phy_gear
- Set phy_gear to minimum value if version < 4 since those versions only
support one PHY init sequence (and therefore don't need reinit)
- Set phy_gear to the optimal value if the device version is already
populated in the controller registers on boot
Let's move some of the comment to outside the if statement and clean up the
bit left about switching to a higher gear on reinit. This way the comment
more accurately reflects the logic.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240123-ufs-reinit-comments-v1-1-ff2b3532d7fe@redhat.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Instead of hardcoding the register field, add the proper definition. While
at it, let's also use ufshcd_rmwl() to simplify updating this register.
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Link: https://lore.kernel.org/r/20240102014222.23351-1-cw9316.lee@samsung.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Change default autosuspend timer from 2000 ms to 500 ms for the MediaTek
driver.
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Link: https://lore.kernel.org/r/20240109124015.31359-3-peter.wang@mediatek.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Disable MCQ IRQ when clock is off. This is same as legacy mode.
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Link: https://lore.kernel.org/r/20231221110416.16176-4-peter.wang@mediatek.com
Reviewed-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix TM cmd timeout issue in MCQ mode using the default resume call
ufshcd_make_hba_operational() to set TM cmd DMA address.
This flow is the same as UFS initialization after link startup and then
setting MCQ related registers if using MCQ mode.
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Link: https://lore.kernel.org/r/20231221110416.16176-3-peter.wang@mediatek.com
Reviewed-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
To prevent SSU(Active) error, check link status after exiting hibern8. If
link is not VS_LINK_UP, return error and do ufshcd_link_recovery.
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Link: https://lore.kernel.org/r/20231221110416.16176-2-peter.wang@mediatek.com
Reviewed-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The PM QoS feature found in the MediaTek UFS driver was moved to the UFSHCD
core. Hence remove it from MediaTek UFS driver as it is redundant now.
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Maramaina Naresh <quic_mnaresh@quicinc.com>
Link: https://lore.kernel.org/r/20231219123706.6463-3-quic_mnaresh@quicinc.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"Final round of fixes that came in too late to send in the first
request.
It's nine bug fixes and one version update (because of a bug fix) and
one set of PCI ID additions. There's one bug fix in the core which is
really a one liner (except that an additional sdev pointer was added
for convenience) and the rest are in drivers"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target: core: Add TMF to tmr_list handling
scsi: core: Kick the requeue list after inserting when flushing
scsi: fnic: unlock on error path in fnic_queuecommand()
scsi: fcoe: Fix unsigned comparison with zero in store_ctlr_mode()
scsi: mpi3mr: Fix mpi3mr_fw.c kernel-doc warnings
scsi: smartpqi: Bump driver version to 2.1.26-030
scsi: smartpqi: Fix logical volume rescan race condition
scsi: smartpqi: Add new controller PCI IDs
scsi: ufs: qcom: Remove unnecessary goto statement from ufs_qcom_config_esi()
scsi: ufs: core: Remove the ufshcd_hba_exit() call from ufshcd_async_scan()
scsi: ufs: core: Simplify power management during async scan
|
|
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, mpi3mr, mpt3sas, lpfc, fnic,
hisi_sas, arcmsr, ) plus the usual assorted minor fixes and updates.
This time around there's only a single line update to the core, so
nothing major and barely anything minor"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (135 commits)
scsi: ufs: core: Simplify ufshcd_auto_hibern8_update()
scsi: ufs: core: Rename ufshcd_auto_hibern8_enable() and make it static
scsi: ufs: qcom: Fix ESI vector mask
scsi: ufs: host: Fix kernel-doc warning
scsi: hisi_sas: Correct the number of global debugfs registers
scsi: hisi_sas: Rollback some operations if FLR failed
scsi: hisi_sas: Check before using pointer variables
scsi: hisi_sas: Replace with standard error code return value
scsi: hisi_sas: Set .phy_attached before notifing phyup event HISI_PHYE_PHY_UP_PM
scsi: ufs: core: Add sysfs node for UFS RTC update
scsi: ufs: core: Add UFS RTC support
scsi: ufs: core: Add ufshcd_is_ufs_dev_busy()
scsi: ufs: qcom: Remove unused definitions
scsi: ufs: qcom: Use ufshcd_rmwl() where applicable
scsi: ufs: qcom: Remove support for host controllers older than v2.0
scsi: ufs: qcom: Simplify ufs_qcom_{assert/deassert}_reset
scsi: ufs: qcom: Initialize cycles_in_1us variable in ufs_qcom_set_core_clk_ctrl()
scsi: ufs: qcom: Sort includes alphabetically
scsi: ufs: qcom: Remove unused ufs_qcom_hosts struct array
scsi: ufs: qcom: Use dev_err_probe() to simplify error handling of devm_gpiod_get_optional()
...
|
|
There is only one place where goto is used, and it is unnecessary to check
the ret value through 'goto out' because the ret value is already true.
Therefore, remove the goto statement and integrate the '!ret' condition
into the existing code.
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Link: https://lore.kernel.org/r/20231219082740.27644-1-cw9316.lee@samsung.com
Reviewed-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
ufs_qcom_clk_scale_notify()
In commit 031312dbc695 ("scsi: ufs: ufs-qcom: Remove unnecessary goto
statements") the error handling was accidentally changed, resulting in the
error of ufs_qcom_clk_scale_*() calls not being returned.
This is the case I checked:
ufs_qcom_clk_scale_notify ->
'ufs_qcom_clk_scale_up_/down_pre_change' error ->
return 0;
Make sure those errors are properly returned.
Fixes: 031312dbc695 ("scsi: ufs: ufs-qcom: Remove unnecessary goto statements")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Link: https://lore.kernel.org/r/20231215003812.29650-1-cw9316.lee@samsung.com
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
While cleaning up the code to use ufshcd_rmwl() helper, the ESI vector mask
was changed incorrectly. Fix it and also define a proper macro for the
value together with FIELD_PREP().
Reported-by: Andrew Halaney <ahalaney@redhat.com>
Fixes: 0e9f4375db1c ("scsi: ufs: qcom: Use ufshcd_rmwl() where applicable")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231214125532.55109-1-manivannan.sadhasivam@linaro.org
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit fa3dca8251c4 ("scsi: ufs: host: Rename structure ufs_dev_params
to ufs_host_params") inadvertently introduced a comment line without
'*' prefix. Format the comment section correctly.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312171915.YhlTLvLL-lkp@intel.com/
Fixes: fa3dca8251c4 ("scsi: ufs: host: Rename structure ufs_dev_params to ufs_host_params")
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> says:
Hello,
This series has code some cleanups to the Qcom UFS driver. No
functional change. In this version, I've removed code supporting
legacy controllers ver < 2.0, as the respective platforms were never
supported in upstream.
Tested on: RB5 development board based on Qcom SM8250 SoC.
Link: https://lore.kernel.org/r/20231208065902.11006-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Remove unused definitions.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-18-manivannan.sadhasivam@linaro.org
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Instead of using both ufshcd_readl() and ufshcd_writel() to read/modify/
write a register, let's make use of the existing helper.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-17-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The legacy platforms making use of host controllers older than version 2.0
are not supported in upstream. So there is no need to carry code to support
them.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-16-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In both the functions, UFS_PHY_SOFT_RESET contains the mask of the reset
bit. So this can be passed directly as the value to be written for
asserting the reset. For deasserting, 0 can be passed.
This gets rid of the FIELD_PREP() inside these functions and also
UFS_PHY_RESET_{ENABLE/DISABLE} definitions.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-15-manivannan.sadhasivam@linaro.org
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
ufs_qcom_set_core_clk_ctrl()
In case the "core_clk_unipro" clock is not provided, "cycles_in_1us"
variable will be used as uninitialized. So initialize it with 0.
Issue reported by Smatch tool:
drivers/ufs/host/ufs-qcom.c:1336 ufs_qcom_set_core_clk_ctrl() error: uninitialized symbol 'cycles_in_1us'.
drivers/ufs/host/ufs-qcom.c:1341 ufs_qcom_set_core_clk_ctrl() error: uninitialized symbol 'cycles_in_1us'.
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-14-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Sort includes alphabetically.
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-13-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
ufs_qcom_hosts array is assigned, but not used anywhere. So let's remove
it.
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-12-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
devm_gpiod_get_optional()
As done in other places, let's use dev_err_probe() to simplify the error
handling while acquiring the device reset gpio using
devm_gpiod_get_optional().
While at it, let's reword the error message to make it clear that the
failure is due to acquiring "device reset gpio".
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-11-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
devm_kzalloc() will itself print the error message on failure. So let's get
rid of the redundant error message in ufs_qcom_init().
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-10-manivannan.sadhasivam@linaro.org
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If ufs_qcom_power_up_sequence() fails, then it makes no sense to enable the
lane clocks and continue ufshcd_hba_enable(). So let's check the return
value of ufs_qcom_power_up_sequence().
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-9-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Even though core_reset is optional, a failure during assert/deassert should
be considered fatal, if core_reset is available. So fail
ufs_qcom_power_up_sequence() if an error happens during reset and also get
rid of the redundant warning as the ufs_qcom_host_reset() function itself
prints error messages.
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-8-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Instead of duplicating the enable/disable IRQ part, let's export the
helpers available in ufshcd driver and make use of them. This also fixes
the possible redundant IRQ disable before asserting reset (when IRQ was
already disabled).
Fixes: 4a791574a0cc ("scsi: ufs: ufs-qcom: Disable interrupt in reset path")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-7-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
core_reset is optional, so there is no need to warn the user if it is not
available.
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-6-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There are many instances where the variable assignments are not needed.
Remove them.
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-5-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The return value should be -ENODEV indicating that the resource is not
provided in DT, not -ENOMEM. Fix it!
Fixes: c263b4ef737e ("scsi: ufs: core: mcq: Configure resource regions")
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-4-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently, the function returns -EINVAL if algorithm other than AES-256-XTS
is requested. But the correct error code is -EOPNOTSUPP. Fix it!
Cc: Abel Vesa <abel.vesa@linaro.org>
Fixes: 56541c7c4468 ("scsi: ufs: ufs-qcom: Switch to the new ICE API")
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-3-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Lane clock handling can be simplified by using the clk_bulk APIs. So let's
make use of them. This also get's rid of the clock validation in the driver
as kernel should just rely on the firmware (DT/ACPI) to provide the clocks
required for proper functioning.
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-2-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Start from HW ver 5, a spare register in UFS host controller is added and
used to indicate the UFS device version. The spare register is populated by
bootloader for now, but in future it will be populated by HW automatically
during link startup with its best efforts in any boot stage prior to Linux.
During host driver init, read the spare register, if it is not populated
with a UFS device version, go ahead with the dual init mechanism. If a UFS
device version is in there, use the UFS device version together with host
controller's HW version to decide the proper PHY gear which should be used
to configure the UFS PHY without going through the second init.
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-9-git-send-email-quic_cang@quicinc.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In ufs_qcom_power_up_sequence(), check return value of phy_set_mode_ext()
and stop proceeding if phy_set_mode_ext() fails.
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-8-git-send-email-quic_cang@quicinc.com
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Since HW ver 4, max HS gear can be get from UFS host controller's register,
use the max HS gear as the initial PHY gear instead of UFS_HS_G2, so that
we don't need to update the hard code for newer targets in future.
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-7-git-send-email-quic_cang@quicinc.com
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Qcom UFS hosts, with HW ver 5, can only support up to HS-G5 Rate-A due to
HW limitations. If the HS-G5 PHY gear is used, update host_params->hs_rate
to Rate-A, so that the subsequent power mode changes shall stick to Rate-A.
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-6-git-send-email-quic_cang@quicinc.com
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During host driver init, the phy_gear is set to the minimum supported gear
(HS_G2). Then, during the first power mode change, the negotiated gear, say
HS-G4, is updated to the phy_gear variable so that in the second init the
updated phy_gear can be used to program the PHY.
But the current code only allows update the phy_gear to a higher value. If
one wants to start the first init with the maximum support gear, say HS-G4,
the phy_gear is not updated to HS-G3 if the device only supports HS-G3.
The original check added there is intend to make sure the phy_gear won't be
updated when gear is scaled down (during clock scaling). Update the check
so that one can start the first init with the maximum support gear without
breaking the original fix by checking the ufshcd_state, that is, allow
update to phy_gear only if power mode change is invoked from
ufshcd_probe_hba().
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-5-git-send-email-quic_cang@quicinc.com
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Setup host power mode and its limitations during UFS host driver init to
avoid repetitive work during every power mode change.
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Co-developed-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-4-git-send-email-quic_cang@quicinc.com
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In ufs_qcom_pwr_change_notify(), host_params.hs_rate has been set to
PA_HS_MODE_B by ufshcd_init_host_param(), hence remove the duplicated line
of work. Meanwhile, removed the macro UFS_QCOM_LIMIT_HS_RATE as it is only
used here.
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-3-git-send-email-quic_cang@quicinc.com
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Structure ufs_dev_params is actually used in UFS host drivers to declare
host specific power mode parameters, like ufs_<vendor>_params or host_cap,
which makes the code not very straightforward to read. Rename the structure
ufs_dev_params to ufs_host_params and unify the declarations in all drivers
to host_params.
In addition, rename the two functions ufshcd_init_pwr_dev_param() and
ufshcd_get_pwr_dev_param() which work based on the ufs_host_params to
ufshcd_init_host_params() and ufshcd_negotiate_pwr_params() respectively to
avoid confusions.
This change does not change any functionalities or logic.
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-2-git-send-email-quic_cang@quicinc.com
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
OPP support added by commit 72208ebe181e ("scsi: ufs: core: Add support for
parsing OPP") doesn't update the min_freq and max_freq of each clock in
'struct ufs_clk_info'.
But these values are used by the host drivers internally for controller
configuration. When the OPP support is enabled in devicetree, these values
will be 0, causing boot issues on the respective platforms.
So add support to parse the min_freq and max_freq of all clocks while
parsing the OPP table.
Fixes: 72208ebe181e ("scsi: ufs: core: Add support for parsing OPP")
Co-developed-by: Manish Pandey <quic_mapa@quicinc.com>
Signed-off-by: Manish Pandey <quic_mapa@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20231208131331.12596-1-quic_nitirawa@quicinc.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
OPP framework can be used to scale the clocks along with other entities
such as regulators, performance state etc... So let's add support for
parsing OPP from devicetree. OPP support in devicetree is added through the
"operating-points-v2" property which accepts the OPP table defining clock
frequency, regulator voltage, power domain performance state etc...
Since the UFS controller requires multiple clocks to be controlled for
proper working, devm_pm_opp_set_config() has been used which supports
scaling multiple clocks through custom ufshcd_opp_config_clks() callback.
It should be noted that the OPP support is not compatible with the old
"freq-table-hz" property. So only one can be used at a time even though
the UFS core supports both.
Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231012172129.65172-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The "attr" pointer points to an offset into the "host" struct so it can't
be NULL. Delete the if statement and pull the code in a tab.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/fe3b8fcd-64a7-4887-bddd-32239a88a6a3@moroto.mountain
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The acpi_evaluate_dsm_typed() provides a way to check the type of the
object evaluated by _DSM call. Use it instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231002135125.2602895-1-andriy.shevchenko@linux.intel.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Bart Van Assche <bvanassche@acm.org> says:
Hi Martin,
Please consider these UFS core patches for the next merge window.
Thanks,
Bart.
Link: https://lore.kernel.org/r/20230921192335.676924-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The DMA alignment for the Exynos controller follows directly from the PRDT
segment size configured in ufs-exynos.c. Hence, move the DMA alignment code
into the Exynos driver source code.
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230921192335.676924-3-bvanassche@acm.org
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
