| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit f69115fdbc1ac0718e7d19ad3caa3da2ecfe1c96 upstream.
According to USB 2 specs ports need to signal resume for at least 20ms,
in practice even longer, before moving to U0 state.
Both host and devices can initiate resume.
On device initiated resume, a port status interrupt with the port in resume
state in issued. The interrupt handler tags a resume_done[port]
timestamp with current time + USB_RESUME_TIMEOUT, and kick roothub timer.
Root hub timer requests for port status, finds the port in resume state,
checks if resume_done[port] timestamp passed, and set port to U0 state.
On host initiated resume, current code sets the port to resume state,
sleep 20ms, and finally sets the port to U0 state. This should also
be changed to work in a similar way as the device initiated resume, with
timestamp tagging, but that is not yet tested and will be a separate
fix later.
There are a few issues with this approach
1. A host initiated resume will also generate a resume event. The event
handler will find the port in resume state, believe it's a device
initiated resume, and act accordingly.
2. A port status request might cut the resume signalling short if a
get_port_status request is handled during the host resume signalling.
The port will be found in resume state. The timestamp is not set leading
to time_after_eq(jiffies, timestamp) returning true, as timestamp = 0.
get_port_status will proceed with moving the port to U0.
3. If an error, or anything else happens to the port during device
initiated resume signalling it will leave all the device resume
parameters hanging uncleared, preventing further suspend, returning
-EBUSY, and cause the pm thread to busyloop trying to enter suspend.
Fix this by using the existing resuming_ports bitfield to indicate that
resume signalling timing is taken care of.
Check if the resume_done[port] is set before using it for timestamp
comparison, and also clear out any resume signalling related variables
if port is not in U0 or Resume state
This issue was discovered when a PM thread busylooped, trying to runtime
suspend the xhci USB 2 roothub on a Dell XPS
Reported-by: Daniel J Blueman <daniel@quora.org>
Tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ccc04afb72cddbdf7c0e1c17e92886405a71b754 upstream.
Intel Broxton M was verifed to require XHCI_PME_STUCK_QUIRK quirk as well.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fa89537783cb442263fa5a14df6c7693eaf32f11 upstream.
Commit abce329c27b3 ("xhci: Workaround to get D3 working in Intel xHCI")
adds a workaround for a limitation of PME storm caused by SSIC port in
some Intel SoCs. This commit only handled one SSIC port, while there
are actually two SSIC ports in the chips. This patch handles both SSIC
ports. Without this fix, users still see PME storm.
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1eaf35e4dd592c59041bc1ed3248c46326da1f5f upstream.
The module should fail to load.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 096b110a3dd3c868e4610937c80d2e3f3357c1a9 upstream.
if a full speed hub connects to a high speed hub which
supports MTT, the MTT field of its slot context will be set
to 1 when xHCI driver setups an xHCI virtual device in
xhci_setup_addressable_virt_dev(); once usb core fetch its
hub descriptor, and need to update the xHC's internal data
structures for the device, the HUB field of its slot context
will be set to 1 too, meanwhile MTT is also set before,
this will cause configure endpoint command fail, so in the
case, we should clear MTT to 0 for full speed hub according
to section 6.2.2
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4a0c4c36094cefd85cbe489590382ef69516ccef upstream.
The interrupt handler, ohci_hcd_at91_overcurrent_irq may be called right
after registration. At that time, pdev->dev.platform_data is not yet set,
leading to a NULL pointer dereference.
Fixes: e4df92279fd9 (USB: host: ohci-at91: merge loops in ohci_hcd_at91_drv_probe)
Reported-by: Peter Rosin <peda@axentia.se>
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f9fa1887dcf26bd346665a6ae3d3f53dec54cba1 upstream.
qset_fill_page_list() do not check for dma mapping errors.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a5964396190d0c40dd549c23848c282fffa5d1f2 upstream.
Existing Intel xHCI controllers require a delay of 1 mS,
after setting the CMD_RESET bit in command register, before
accessing any HC registers. This allows the HC to complete
the reset operation and be ready for HC register access.
Without this delay, the subsequent HC register access,
may result in a system hang, very rarely.
Verified CherryView / Braswell platforms go through over
5000 warm reboot cycles (which was not possible without
this patch), without any xHCI reset hang.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 42df7215facf27be8d53e657dd4a12d4ebad0a44 upstream.
Function ep_ring_is_processing() checks the dequeue pointer
in endpoint context to know whether an endpoint is busy with
processing TRBs. This is not correct since dequeue pointer
field in an endpoint context is only valid when the endpoint
is in Halted or Stopped states. This buggy code causes audio
noise when playing sound with USB headset connected to host
controllers which support CFC (one of xhci 1.1 features).
This patch should exist in stable kernel since v4.3.
Reported-and-tested-by: YD Tseng <yd_tseng@asmedia.com.tw>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db1319e166c5e872c4be54eac4e47454133708cf upstream.
Commit d445913ce0ab7f ("usb: ehci-orion: add optional PHY support")
added support for optional phys, but devm_phy_optional_get returns
-ENOSYS if GENERIC_PHY is not enabled.
This causes probe failures, even when there are no phys specified:
[ 1.443365] orion-ehci f1058000.usb: init f1058000.usb fail, -38
[ 1.449403] orion-ehci: probe of f1058000.usb failed with error -38
Similar to dwc3, treat -ENOSYS as no phy.
Fixes: d445913ce0ab7f ("usb: ehci-orion: add optional PHY support")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We received several reports of systems rebooting and powering on
after an attempted shutdown. Testing showed that setting
XHCI_SPURIOUS_WAKEUP quirk in addition to the XHCI_SPURIOUS_REBOOT
quirk allowed the system to shutdown as expected for LynxPoint-LP
xHCI controllers. Set the quirk back.
Note that the quirk was originally introduced for LynxPoint and
LynxPoint-LP just for this same reason. See:
commit 638298dc66ea ("xhci: Fix spurious wakeups after S5 on Haswell")
It was later limited to only concern HP machines as it caused
regression on some machines, see both bug and commit:
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66171
commit 6962d914f317 ("xhci: Limit the spurious wakeup fix only to HP machines")
Later it was discovered that the powering on after shutdown
was limited to LynxPoint-LP (Haswell-ULT) and that some non-LP HP
machine suffered from spontaneous resume from S3 (which should
not be related to the SPURIOUS_WAKEUP quirk at all). An attempt
to fix this then removed the SPURIOUS_WAKEUP flag usage completely.
commit b45abacde3d5 ("xhci: no switching back on non-ULT Haswell")
Current understanding is that LynxPoint-LP (Haswell ULT) machines
need the SPURIOUS_WAKEUP quirk, otherwise they will restart, and
plain Lynxpoint (Haswell) machines may _not_ have the quirk
set otherwise they again will restart.
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Oliver Neukum <oneukum@suse.com>
[Added more history to commit message -Mathias]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a host fails to wake up a isochronous SuperSpeed device from U1/U2
in time for a isoch transfer it will generate a "No ping response error"
Host will then move to the next transfer descriptor.
Handle this case in the same way as missed service errors, tag the
current TD as skipped and handle it on the next transfer event.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the difference is big enough between the bytes asked and received
in a bulk transfer we can get a short transfer event pointing to a TRB in
the middle of the TD. We don't want to handle the TD yet as we will anyway
receive a new event for the last TRB in the TD.
Hold off from finishing the TD and removing it from the list until we
receive an event for the last TRB in the TD
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't check if timer is running with a timer_pending() before
deleting it with del_timer_sync(), this defies the whole point of
the sync part and can cause a possible race.
Instead we just want to make sure the timer is initialized early enough
before we have a chance to delete it.
Cc: <stable@vger.kernel.org>
Reported-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some changes between xhci 0.96 and xhci 1.0 specifications forced us to
check the hci version in code, some of these checks were implemented as
hci_version == 1.0, which will not work with new xhci 1.1 controllers.
xhci 1.1 behaves similar to xhci 1.0 in these cases, so change these
checks to hci_version >= 1.0
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During quick plug/removal of OTG adapter during dual-role testing
it can happen that xhci_alloc_device() is called for the newly
detected device after the DRD library has called xhci_stop to
remove the HCD.
If that is the case, just fail early to prevent the following warning.
[ 154.732649] hub 4-0:1.0: USB hub found
[ 154.742204] hub 4-0:1.0: 1 port detected
[ 154.824458] hub 3-0:1.0: state 7 ports 1 chg 0002 evt 0000
[ 154.854609] hub 4-0:1.0: state 7 ports 1 chg 0000 evt 0000
[ 154.944430] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[ 154.951009] xhci-hcd xhci-hcd.0.auto: xhci_setup_device
[ 155.038191] xhci-hcd xhci-hcd.0.auto: remove, state 4
[ 155.043315] usb usb4: USB disconnect, device number 1
[ 155.055270] xhci-hcd xhci-hcd.0.auto: xhci_stop
[ 155.060094] xhci-hcd xhci-hcd.0.auto: USB bus 4 deregistered
[ 155.066576] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 155.071710] usb usb3: USB disconnect, device number 1
[ 155.077124] xhci-hcd xhci-hcd.0.auto: xhci_setup_device
[ 155.082389] ------------[ cut here ]------------
[ 155.087690] WARNING: CPU: 0 PID: 72 at drivers/usb/host/xhci.c:3800 xhci_setup_device+0x410/0x484 [xhci_hcd]()
[ 155.097861] Modules linked in: sd_mod usb_storage scsi_mod usb_f_ss_lb g_zero libcomposite ipv6 xhci_plat_hcd xhci_hcd usbcore dwc3 udc_core evdev ti_am335x_adc joydev kfifo_buf industrialio snd_soc_simple_cc
[ 155.146734] CPU: 0 PID: 72 Comm: kworker/0:3 Tainted: G W 4.1.4-00834-gcd9380b-dirty #50
[ 155.156073] Hardware name: Generic AM43 (Flattened Device Tree)
[ 155.162117] Workqueue: usb_hub_wq hub_event [usbcore]
[ 155.167249] Backtrace:
[ 155.169751] [<c0012af0>] (dump_backtrace) from [<c0012c8c>] (show_stack+0x18/0x1c)
[ 155.177390] r6:c089d4a4 r5:ffffffff r4:00000000 r3:ee46c000
[ 155.183137] [<c0012c74>] (show_stack) from [<c05f7c14>] (dump_stack+0x84/0xd0)
[ 155.190446] [<c05f7b90>] (dump_stack) from [<c00439ac>] (warn_slowpath_common+0x80/0xbc)
[ 155.198605] r7:00000009 r6:00000ed8 r5:bf27eb70 r4:00000000
[ 155.204348] [<c004392c>] (warn_slowpath_common) from [<c0043a0c>] (warn_slowpath_null+0x24/0x2c)
[ 155.213202] r8:ee49f000 r7:ee7c0004 r6:00000000 r5:ee7c0158 r4:ee7c0000
[ 155.220051] [<c00439e8>] (warn_slowpath_null) from [<bf27eb70>] (xhci_setup_device+0x410/0x484 [xhci_hcd])
[ 155.229816] [<bf27e760>] (xhci_setup_device [xhci_hcd]) from [<bf27ec10>] (xhci_address_device+0x14/0x18 [xhci_hcd])
[ 155.240415] r10:ee598200 r9:00000001 r8:00000002 r7:00000001 r6:00000003 r5:00000002
[ 155.248363] r4:ee49f000
[ 155.250978] [<bf27ebfc>] (xhci_address_device [xhci_hcd]) from [<bf20cb94>] (hub_port_init+0x1b8/0xa9c [usbcore])
[ 155.261403] [<bf20c9dc>] (hub_port_init [usbcore]) from [<bf2101e0>] (hub_event+0x738/0x1020 [usbcore])
[ 155.270874] r10:ee598200 r9:ee7c0000 r8:ee7c0038 r7:ee518800 r6:ee49f000 r5:00000001
[ 155.278822] r4:00000000
[ 155.281426] [<bf20faa8>] (hub_event [usbcore]) from [<c005754c>] (process_one_work+0x128/0x340)
[ 155.290196] r10:00000000 r9:00000003 r8:00000000 r7:fedfa000 r6:eeec5400 r5:ee598314
[ 155.298151] r4:ee434380
[ 155.300718] [<c0057424>] (process_one_work) from [<c00578f8>] (worker_thread+0x158/0x49c)
[ 155.308963] r10:ee434380 r9:00000003 r8:eeec5400 r7:00000008 r6:ee434398 r5:eeec5400
[ 155.316913] r4:eeec5414
[ 155.319482] [<c00577a0>] (worker_thread) from [<c005cc40>] (kthread+0xdc/0xf8)
[ 155.326765] r10:00000000 r9:00000000 r8:00000000 r7:c00577a0 r6:ee434380 r5:ee4441c0
[ 155.334713] r4:00000000 r3:00000000
[ 155.338341] [<c005cb64>] (kthread) from [<c000fc08>] (ret_from_fork+0x14/0x2c)
[ 155.345626] r7:00000000 r6:00000000 r5:c005cb64 r4:ee4441c0
[ 155.356108] ---[ end trace a58d34c223b190e6 ]---
[ 155.360783] xhci-hcd xhci-hcd.0.auto: Virt dev invalid for slot_id 0x1!
[ 155.574404] xhci-hcd xhci-hcd.0.auto: xhci_setup_device
[ 155.579667] ------------[ cut here ]------------
Cc: <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci_stop will be called twice, once for the shared hcd
and again for the primary hcd.
We stop the XHCI controller in any case so clean up
everything on the first call else we can timeout
waiting for pending requests to complete.
Cc: <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For whatever reason if XHCI died in the previous instant
then it will never recover on the next xhci_start unless we
clear the DYING flag.
Cc: <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Else it races with xhci_setup_device
Cc: <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci_pme_quirk() is only used when CONFIG_PM is defined.
Compiling a kernel without PM complains about this function
[reworded commit message -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Tomer Barletz <barletz@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want to give the command abortion an additional try to stop
the command ring before we completely hose xhci.
Cc: <stable@vger.kernel.org>
Tested-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ehci platform device's drvdata is the pointer of struct usb_hcd
already, so we doesn't need to call bus_to_hcd conversion again.
Cc: <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ohci_hcd_at91_drv_probe() has four at91_for_each_port. They can be merged
into two loops without changing the driver behaviour.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As device tree support is now mandatory, merge ohci_at91_of_init() in
ohci_hcd_at91_drv_probe().
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make the driver depend on CONFIG_OF and remove the now useless #ifdef
Also, fix the Kconfig indentation.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move struct at91_usbh_data back in ohci-at91.c as this is the only user
left after switching all at91 platforms to DT only.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Incoming packets in high speed are randomly corrupted by h/w
resulting in multiple errors. This workaround makes FS as
default mode in all affected socs by disabling HS chirp
signalling.This errata does not affect FS and LS mode.
Forces all HS devices to connect in FS mode for all socs
affected by this erratum:
P3041 and P2041 rev 1.0 and 1.1
P5020 and P5010 rev 1.0 and 2.0
P5040, P1010 and T4240 rev 1.0
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch enables xhci driver to support SPC by handling
Stopped - Short Packet event in transfer event path.
If SPC = '1' and the stop endpoint command is executed, after a Short
Packet condition has been detected, but before the end of the TD has been
reached, (i.e. the TD is in progress for pipe), then a Transfer Event TRB
with its Completion Code set to Stopped - Short Packet and its TRB
Transfer Length set to value of the EDTLA shall be forced for the
interrupted TRB, irrespective of whether its IOC or ISP flags are set.
This Transfer Event TRB will precede the Command Completion Event TRB for
the command, and is referred to as a Stopped Transfer Event.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the Contiguous Frame ID Capability is supported (CFC = 1),
then the xHC shall match the Frame ID in every Isoch TD with
SIA = 0 against the Frame Index of the MFINDEX register. This
rule ensures resynchronization of Isoch TDs even if some are
dropped due to Missed Service Errors or Stopping the endpoint.
This patch enables xHCI driver to support CFC by calculating
and setting the Frame ID field of an Isoch TRB.
[made some dbg messages checkpatch friendly -Mathias]
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This commit checks for the URB_ZERO_PACKET flag and creates an extra
zero-length td if the urb transfer length is a multiple of the endpoint's
max packet length.
Signed-off-by: Reyad Attiyat <reyad.attiyat@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Right now xhci-plat-hcd can be built when using one of platform specific
drivers only (mvebu/rcar). There shouldn't be such limitation as some
platforms may not require any quirks and may want to just use a generic
driver ("generic-xhci" / "xhci-hcd").
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace redundant variable use in return statement.
Signed-off-by: Saurabh Karajgaonkar <skarajga@visteon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace redundant variable use in return statement.
Signed-off-by: Saurabh Karajgaonkar <skarajga@visteon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace redundant variable use in return statement.
Signed-off-by: Saurabh Karajgaonkar <skarajga@visteon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace redundant variable use in return statement.
Signed-off-by: Saurabh Karajgaonkar <skarajga@visteon.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When using OF defined controllers the platform data struct is shared
between all devices, so it can't be used for device specific settings.
However it is currently used for the OF properties
needs-reset-on-resume and has-transaction-translator.
To fix this issue move setting hcd->has_tt to the probe and
move pdata->reset_on_resume to the private data.
Signed-off-by: Alban Bedel <albeu@free.fr>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When xhci_mem_cleanup() is called, it's possible that the command
timer isn't initialized and scheduled. For those cases, to delete
the command timer causes soft-lockup as below stack dump shows.
The patch avoids deleting the command timer if it's not scheduled
with the help of timer_pending().
NMI watchdog: BUG: soft lockup - CPU#40 stuck for 23s! [kworker/40:1:8140]
:
NIP [c000000000150b30] lock_timer_base.isra.34+0x90/0xa0
LR [c000000000150c24] try_to_del_timer_sync+0x34/0xa0
Call Trace:
[c000000f67c975e0] [c0000000015b84f8] mon_ops+0x0/0x8 (unreliable)
[c000000f67c97620] [c000000000150c24] try_to_del_timer_sync+0x34/0xa0
[c000000f67c97660] [c000000000150cf0] del_timer_sync+0x60/0x80
[c000000f67c97690] [c00000000070ac0c] xhci_mem_cleanup+0x5c/0x5e0
[c000000f67c97740] [c00000000070c2e8] xhci_mem_init+0x1158/0x13b0
[c000000f67c97860] [c000000000700978] xhci_init+0x88/0x110
[c000000f67c978e0] [c000000000701644] xhci_gen_setup+0x2b4/0x590
[c000000f67c97970] [c0000000006d4410] xhci_pci_setup+0x40/0x190
[c000000f67c979f0] [c0000000006b1af8] usb_add_hcd+0x418/0xba0
[c000000f67c97ab0] [c0000000006cb15c] usb_hcd_pci_probe+0x1dc/0x5c0
[c000000f67c97b50] [c0000000006d3ba4] xhci_pci_probe+0x64/0x1f0
[c000000f67c97ba0] [c0000000004fe9ac] local_pci_probe+0x6c/0x130
[c000000f67c97c30] [c0000000000e5ce8] work_for_cpu_fn+0x38/0x60
[c000000f67c97c60] [c0000000000eacb8] process_one_work+0x198/0x470
[c000000f67c97cf0] [c0000000000eb6ac] worker_thread+0x37c/0x5a0
[c000000f67c97d80] [c0000000000f2730] kthread+0x110/0x130
[c000000f67c97e30] [c000000000009660] ret_from_kernel_thread+0x5c/0x7c
Cc: <stable@vger.kernel.org>
Reported-by: Priya M. A <priyama2@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need to check that a TRB is part of the current segment
before calculating its DMA address.
Previously a ring segment didn't use a full memory page, and every
new ring segment got a new memory page, so the off by one
error in checking the upper bound was never seen.
Now that we use a full memory page, 256 TRBs (4096 bytes), the off by one
didn't catch the case when a TRB was the first element of the next segment.
This is triggered if the virtual memory pages for a ring segment are
next to each in increasing order where the ring buffer wraps around and
causes errors like:
[ 106.398223] xhci_hcd 0000:00:14.0: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 0 comp_code 1
[ 106.398230] xhci_hcd 0000:00:14.0: Looking for event-dma fffd3000 trb-start fffd4fd0 trb-end fffd5000 seg-start fffd4000 seg-end fffd4ff0
The trb-end address is one outside the end-seg address.
Cc: <stable@vger.kernel.org>
Tested-by: Arkadiusz Miśkiewicz <arekm@maven.pl>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the USB fixes that went into that release in this branch as
well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Define and use CONTROL_REGISTER_W1C_MASK to make sure that
w1c bits of usb control register do not get reset while
writing any other bit
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Phy_clk_valid bit is checked only when the boolean
property phy-clk-valid in present in usb node device tree.
This property is added to the usb node via device tree fixup.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Introduce FSL_USB2_PHY_UTMI_DUAL macro for setting phy mode
in SOCs such has T4240, T1040, T2080 which have utmi dual-phy
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB controller version-2.5 requires to enable internal UTMI
phy and program PTS field in PORTSC register before asserting
controller reset. This is must for successful resetting of the
controller and subsequent enumeration of usb devices
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace macros with enumerated type to represent usb ip
controller version
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some boards a GPIO is needed to activate USB controller. Make it
possible to specify such a GPIO in device tree.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Broadcom ARM SoCs with this usb core need a different
initialization and they have a different core id. This patch adds
support for these USB 2.0 core.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch makes bcma_hcd_create_pdev() not return NULL, but a prober
error code in case of an error.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of manually handling the frees use devm. There was also a free
missing in the unregister call which is not needed with devm.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The constants for these numbers were added long time ago, use them.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
