| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
i2c_device_id::driver_data to 0
These driver don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240710073050.192806-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This add the support to set the optional connector orientation bit which
is part of the optional CONFIG_STANDARD_OUTPUT register 0x18 [1]. This
allows system designers to connect the tcpc orientation pin directly to
the 2:1 ss-mux.
[1] https://www.usb.org/sites/default/files/documents/usb-port_controller_specification_rev2.0_v1.0_0.pdf
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240701132133.3054394-1-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver already support the tcpci binding for the i2c_device_id so
add the support for the of_device_id too.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240222210903.208901-3-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add attempt_vconn_swap_discovery callback to determine whether the TCPM
should perform a Vconn swap following Discover Identity on SOP. The tcpci
will return false unless chip level drivers implement the callback.
Maxim based TCPCs will return true unless the last connection resulted in
a Vconn Over Current Fault, which may be the result of the Vconn swap. In
addition to the port resetting, the TCPCI will veto the next Vconn swap
from occurring.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-21-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tcpm_pd_receive adds the SOP type as a parameter, and passes it within the
pd_rx_event struct for tcpm_pd_rx_handler to use. For now, the handler
drops all SOP' messages.
Maxim based tcpci drivers are capable of SOP' communication, so process_rx
now takes the SOP type into account and passes the value to
tcpm_pd_receive.
tcpci_set_pd_rx now utilizes the cable_comm_capable flag to determine if
TCPC_RX_DETECT_SOP1 should be added to the bitfield when enabling PD
message reception.
For all other consumers of tcpm_pd_receive, default the new field to
TCPC_TX_SOP.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-18-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add cable_comm_capable to tcpci_data for tcpci drivers to indicate that
the port tcpc is capable of communicating to cables over SOP. A
corresponding tcpci callback tcpci_cable_comm_capable returns this value.
The tcpm will primarily use this in later patches to determine if the port
can transmit and receive SOP' messages.
Maxim based tcpci drivers are capable of SOP' communication, so the
cable_comm_capable flag is set to true.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-17-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According the "USB Type-C Port Controller Interface Specification v2.0"
the TCPC sets the fault status register bit-7
(AllRegistersResetToDefault) once the registers have been reset to
their default values.
This triggers an alert(-irq) on PTN5110 devices albeit we do mask the
fault-irq, which may cause a kernel hang. Fix this generically by writing
a one to the corresponding bit-7.
Cc: stable@vger.kernel.org
Fixes: 74e656d6b055 ("staging: typec: Type-C Port Controller Interface driver (tcpci)")
Reported-by: "Angus Ainslie (Purism)" <angus@akkea.ca>
Closes: https://lore.kernel.org/all/20190508002749.14816-2-angus@akkea.ca/
Reported-by: Christian Bach <christian.bach@scs.ch>
Closes: https://lore.kernel.org/regressions/ZR0P278MB07737E5F1D48632897D51AC3EB329@ZR0P278MB0773.CHEP278.PROD.OUTLOOK.COM/t/
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230816172502.1155079-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
While touching hd3ss3220.c fix a minor white space issue in the
definition of struct hd3ss3220_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517181528.167115-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This change adds callback to evaluate presence of contaminant in
the TCPCI layer.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20230114093246.1933321-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Under resource constraints, this interrupt may use other interrupt line
or this interrupt line may be shared with other devices as long as they
meet the sharing requirements. Besides, This irq flag will not cause other
side effect if tcpci driver is the only user.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221214022334.2520677-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-581-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
I got the following report while doing device(mt6370-tcpc) load
test with CONFIG_OF_UNITTEST and CONFIG_OF_DYNAMIC enabled:
OF: ERROR: memory leak, expected refcount 1 instead of 2,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /i2c/pmic@34/tcpc/connector
The 'fwnode' set in tcpci_parse_config() which is called
in tcpci_register_port(), its node refcount is increased
in device_get_named_child_node(). It needs be put while
exiting, so call fwnode_handle_put() in the error path of
tcpci_register_port() and in tcpci_unregister_port() to
avoid leak.
Fixes: 5e85a04c8c0d ("usb: typec: add fwnode to tcpc")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221121062416.1026192-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for 6.1-rc1.
Nothing major in here, lots of little things with new devices
supported and updates for a few drivers. Highlights include:
- thunderbolt/USB4 devices supported a bit better than before, and
some new ids to enable new hardware devices
- USB gadget uvc updates for newer video formats and better v4l
integration (the v4l portions were acked by those maintainers)
- typec updates for tiny issues and more typec drivers for new chips.
- xhci tiny updates for minor issues
- big usb-serial ftdi_sio driver update to handle new devices better
- lots of tiny dwc3 fixes and updates for the IP block that is
showing up everywhere these days
- dts updates for new devices being supported
- other tiny janitorial and cleanups fixes for lots of different USB
drivers. Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: gadget: uvc: don't put item still in use
usb: gadget: uvc: Fix argument to sizeof() in uvc_register_video()
usb: host: ehci-exynos: switch to using gpiod API
Revert "usb: dwc3: Don't switch OTG -> peripheral if extcon is present"
Revert "USB: fixup for merge issue with "usb: dwc3: Don't switch OTG -> peripheral if extcon is present""
dt-bindings: usb: Convert FOTG210 to dt schema
usb: mtu3: fix failed runtime suspend in host only mode
USB: omap_udc: Fix spelling mistake: "tranceiver_ctrl" -> "transceiver_ctrl"
usb: typec: ucsi_ccg: Disable UCSI ALT support on Tegra
usb: typec: Replace custom implementation of device_match_fwnode()
usb: typec: ucsi: Don't warn on probe deferral
usb: add quirks for Lenovo OneLink+ Dock
MAINTAINERS: switch dwc3 to Thinh
usb: idmouse: fix an uninit-value in idmouse_open
USB: PHY: JZ4770: Switch to use dev_err_probe() helper
usb: phy: generic: Switch to use dev_err_probe() helper
usb: ulpi: use DEFINE_SHOW_ATTRIBUTE to simplify ulpi_regs
usb: cdns3: remove dead code
usb: cdc-wdm: Use skb_put_data() instead of skb_put/memcpy pair
usb: musb: sunxi: Switch to use dev_err_probe() helper
...
|
|
Move transition function "tcpci_to_typec_cc" to common header
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Gene Chen <gene_chen@richtek.com>
Link: https://lore.kernel.org/r/20220805071714.150882-7-gene.chen.richtek@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
USB PD controllers which consisting of a microcontroller (acting as the TCPM)
and a port controller (TCPC) - may require that the driver for the PD
controller accesses directly also the on-chip port controller in some cases.
Move tcpci.h to include/linux/usb/ is convenience access TCPC registers.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Link: https://lore.kernel.org/r/20220706083433.2415524-1-xji@analogixsemi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Returning an error value in an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
In this case the remove callback even returns early without stopping the
tcpm worker thread and various timers. A work scheduled on the work
queue, or a firing timer after tcpci_remove() returned probably results
in a use-after-free situation because the regmap and driver data were
freed. So better make sure that tcpci_unregister_port() is called even
if disabling the irq failed.
Also emit a more specific error message instead of the i2c core's
"remove failed (EIO), will be ignored" and return 0 to suppress the
core's warning.
This patch is (also) a preparation for making i2c remove callbacks
return void.
Fixes: 3ba76256fc4e ("usb: typec: tcpci: mask event interrupts when remove driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220502080456.21568-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With the AMS and Collision Avoidance, tcpm often needs to change the CC's
termination. When one CC line is sourcing Vconn, if we still change its
termination, the voltage of the another CC line is likely to be fluctuant
and unstable.
Therefore, we should verify whether a CC line is sourcing Vconn before
changing its termination and only change the termination that is not
a Vconn line. This can be done by reading the Vconn Present bit of
POWER_ STATUS register. To determine the polarity, we can read the
Plug Orientation bit of TCPC_CONTROL register. Since Vconn can only be
sourced if Plug Orientation is set.
Fixes: 0908c5aca31e ("usb: typec: tcpm: AMS and Collision Avoidance")
cc: <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20220113092943.752372-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB TCPCI Spec, 4.4.3 Mask Registers:
"A masked register will still indicate in the ALERT register, but shall
not set the Alert# pin low."
Thus, the Extended Status will still indicate in ALERT register if vSafe0V
is detected by TCPC even though being masked. In current code, howerer,
this event will not be handled in detection time. Rather it will be
handled when next ALERT event coming(CC evnet, PD event, etc).
Tcpm might transition to a wrong state in this situation. Thus, the vSafe0V
event should not be handled when it's masked.
Fixes: 766c485b86ef ("usb: typec: tcpci: Add support to report vSafe0V")
cc: <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20210926101415.3775058-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a spelling mistake in a comment. Fix it.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20210922060152.2892027-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
"Table 4-3 VBUS Sink Characteristics" of "Type-C Cable and Connector
Specification" defines the disconnect voltage thresholds of various
configurations. This change fixes the disconnect threshold voltage
calculation based on vSinkPD_min and vSinkDisconnectPD as defined
by the table.
Fixes: e1a97bf80a022 ("usb: typec: tcpci: Implement Auto discharge disconnect callbacks")
Cc: stable <stable@vger.kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210615174323.1160132-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sparse tool complains as follows:
drivers/usb/typec/tcpm/tcpci.c:118:5: warning:
symbol 'tcpci_apply_rc' was not declared. Should it be static?
This symbol is not used outside of tcpci.c, so marks it static.
Fixes: 7257fbc7c598 ("usb: typec: tcpci: Implement callback for apply_rc")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210524133704.2432555-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
APPLY RC is defined as ROLE_CONTROL.CC1 != ROLE_CONTROL.CC2 and
POWER_CONTROL.AutodischargeDisconnect is 0. When ROLE_CONTROL.CC1 ==
ROLE_CONTROL.CC2, set the other CC to OPEN.
Fixes: f321a02caebd ("usb: typec: tcpm: Implement enabling Auto Discharge disconnect support")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210517192112.40934-4-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Defining one macro instead of two for tcpc_presenting_*_rd.
This is a follow up of the comment left by Heikki Krogerus.
https://patchwork.kernel.org/project/linux-usb/patch/
20210304070931.1947316-1-badhri@google.com/
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210310223536.3471243-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While interpreting CC_STATUS, ROLE_CONTROL has to be read to make
sure that CC1/CC2 is not forced presenting Rp/Rd.
>From the TCPCI spec:
4.4.5.2 ROLE_CONTROL (Normative):
The TCPM shall write B6 (DRP) = 0b and B3..0 (CC1/CC2) if it wishes
to control the Rp/Rd directly instead of having the TCPC perform
DRP toggling autonomously. When controlling Rp/Rd directly, the
TCPM writes to B3..0 (CC1/CC2) each time it wishes to change the
CC1/CC2 values. This control is used for TCPM-TCPC implementing
Source or Sink only as well as when a connection has been detected
via DRP toggling but the TCPM wishes to attempt Try.Src or Try.Snk.
Table 4-22. CC_STATUS Register Definition:
If (ROLE_CONTROL.CC1 = Rd) or ConnectResult=1)
00b: SNK.Open (Below maximum vRa)
01b: SNK.Default (Above minimum vRd-Connect)
10b: SNK.Power1.5 (Above minimum vRd-Connect) Detects Rp-1.5A
11b: SNK.Power3.0 (Above minimum vRd-Connect) Detects Rp-3.0A
If (ROLE_CONTROL.CC2=Rd) or (ConnectResult=1)
00b: SNK.Open (Below maximum vRa)
01b: SNK.Default (Above minimum vRd-Connect)
10b: SNK.Power1.5 (Above minimum vRd-Connect) Detects Rp 1.5A
11b: SNK.Power3.0 (Above minimum vRd-Connect) Detects Rp 3.0A
Fixes: 74e656d6b0551 ("staging: typec: Type-C Port Controller Interface driver (tcpci)")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210304070931.1947316-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB Communications Capable bit indicates if port
partner is capable of communication over the USB data lines
(e.g. D+/- or SS Tx/Rx). TCPM passes this information for chip specific
operations.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210202003101.221145-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Auto discharge circuits kick in only when vbus decays and reaches
VBUS_SINK_DISCONNECT_THRESHOLD threshold. Enable bleed discharge to
discharge vbus to VBUS_SINK_DISCONNECT_THRESHOLD upon disconnect.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201211071145.2199997-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This change adds vbus_vsafe0v which when set, makes TCPM
query for VSAFE0V by assigning the tcpc.is_vbus_vsafe0v callback.
Also enables ALERT.ExtendedStatus which is triggered when
status of EXTENDED_STATUS.vSafe0V changes.
EXTENDED_STATUS.vSafe0V is set when vbus is at vSafe0V and
cleared otherwise.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201202040840.663578-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
nRetryCount was updated from 3 to 2 between PD2.0 and PD3.0 spec.
nRetryCount in "Table 6-34 Counter parameters" of the PD 2.0
spec is set to 3, whereas, nRetryCount in "Table 6-59 Counter
parameters" is set to 2.
Pass down negotiated rev in pd_transmit so that low level chip
drivers can update the retry count accordingly before attempting
packet transmission.
This helps in passing "TEST.PD.PORT.ALL.02" of the
"Power Delivery Merged" test suite which was initially failing
with "The UUT did not retransmit the message nReryCount times"
In fusb302 & tcpci drivers, by default the driver sets the retry
count to 3 (Default for PD 2.0). Update this to 2,
if the negotiated rev is PD 3.0.
In wcove, since the retry count is intentionally set to max, leaving
it as is.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201202031733.647808-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
vImplement callbacks for enabling/disabling
POWER_CONTROL.AutoDischargeDisconnect.
Programs VBUS_SINK_DISCONNECT_THRESHOLD based on the
voltage requested as sink, mode of operation.
The programmed threshold is based on vSinkDisconnect and
vSinkDisconnectPD values.
Add auto_discharge_disconnect to tdata to allow TCPC chip
level drivers enable AutoDischargeDisconnect.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-9-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During FRS hardware autonomously starts to source vbus. Provide
callback to perform chip specific operations.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-6-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Implement tcpc.enable_frs to enable TCPC to receive
Fast role swap signal.
Additionally set the sink disconnect threshold to 4v
to prevent disconnect during Fast Role swap.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-8-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
set_vbus callback allows TCPC which are TCPCI based, however,
does not support turning on sink and source mode through
Command.SinkVbus and Command.SourceVbusDefaultVoltage.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allow chip level drivers to retrieve reference to tcpm_port.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ROLE_CONTROL register would not have the actual CC terminations
unless the port does not set ROLE_CONTROL.DRP. For DRP ports,
CC_STATUS.cc1/cc2 indicates the final terminations applied
when TCPC enters potential_connect_as_source/_sink.
For DRP ports, infer port role from CC_STATUS and set corresponding
CC terminations before setting the orientation.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20200901025927.3596190-4-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
TCPCI spec forbids direct access of TX_BUF_BYTE_x register.
The existing version of tcpci driver assumes that those registers
are directly addressible. Add support for tcpci chips which do
not support direct access to TX_BUF_BYTE_x registers. TX_BUF_BYTE_x
can only be accessed by I2C_WRITE_BYTE_COUNT.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20200901025927.3596190-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
Quoting from TCPCI spec:
"Setting this bit to 1 is intended to be used only when a USB compliance
tester is using USB BIST Test Data to test the PHY layer of the TCPC. The
TCPM should clear this bit when a disconnect is detected.
0: Normal Operation. Incoming messages enabled by RECEIVE_DETECT
passed to TCPM via Alert.
1: BIST Test Mode. Incoming messages enabled by RECEIVE_DETECT
result in GoodCRC response but may not be passed to the TCPM via
Alert."
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200716034128.1251728-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is to prevent any possible events generated while unregister
tpcm port.
Fixes: 74e656d6b055 ("staging: typec: Type-C Port Controller Interface driver (tcpci)")
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1579502333-4145-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Augmented Power Delivery Objects (A)PDO_s are used by USB-C
PD power adapters to advertize the voltages and currents
they support. There can be up to 7 PDO_s but before PPS
(programmable power supply) there were seldom more than 4
or 5. Recently Samsung released an optional PPS 45 Watt power
adapter (EP-TA485) that has 7 PDO_s. It is for the Galaxy 10+
tablet and charges it quicker than the adapter supplied at
purchase. The EP-TA485 causes an overzealous WARN_ON to soil
the log plus it miscalculates the number of bytes to read.
So this bug has been there for some time but goes
undetected for the majority of USB-C PD power adapters on
the market today that have 6 or less PDO_s. That may soon
change as more USB-C PD adapters with PPS come to market.
Tested on a EP-TA485 and an older Lenovo PN: SA10M13950
USB-C 65 Watt adapter (without PPS and has 4 PDO_s) plus
several other PD power adapters.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191230033544.1809-1-dgilbert@interlog.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some tcpc device-drivers need to explicitly be told to watch for connection
events, otherwise the tcpc will not generate any TCPM_CC_EVENTs and devices
being plugged into the Type-C port will not be noticed.
For dual-role ports tcpm_start_drp_toggling() is used to tell the tcpc to
watch for connection events. Sofar we lack a similar callback to the tcpc
for single-role ports. With some tcpc-s such as the fusb302 this means
no TCPM_CC_EVENTs will be generated when the port is configured as a
single-role port.
This commit renames start_drp_toggling to start_toggling and since the
device-properties are parsed by the tcpm-core, adds a port_type parameter
to the start_toggling callback so that the tcpc_dev driver knows the
port-type and can act accordingly when it starts toggling.
The new start_toggling callback now always gets called if defined, instead
of only being called for DRP ports.
To avoid this causing undesirable functional changes all existing
start_drp_toggling implementations are not only renamed to start_toggling,
but also get a port_type check added and return -EOPNOTSUPP when port_type
is not DRP.
Fixes: ea3b4d5523bc("usb: typec: fusb302: Resolve fixed power role ...")
Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Moving all the drivers that depend on the Port Controller
Manager under a new directory drivers/usb/typec/tcpm/ and
making Guenter Roeck the designated reviewer of that code.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
