Age | Commit message (Collapse) | Author | Files | Lines |
|
commit 3483254b89438e60f719937376c5e0ce2bc46761 upstream.
To match the Corsair Strafe RGB, the Corsair K70 RGB also requires
USB_QUIRK_DELAY_CTRL_MSG to completely resolve boot connection issues
discussed here: https://github.com/ckb-next/ckb-next/issues/42.
Otherwise roughly 1 in 10 boots the keyboard will fail to be detected.
Patch that applied delay control quirk for Corsair Strafe RGB:
cb88a0588717 ("usb: quirks: add control message delay for 1b1c:1b20")
Previous K70 RGB patch to add delay-init quirk:
7a1646d92257 ("Add delay-init quirk for Corsair K70 RGB keyboards")
Signed-off-by: Jack Stocker <jackstocker.93@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0a99cc4b8ee83885ab9f097a3737d1ab28455ac0 upstream.
The SMI SM3350 USB-UFS bridge controller cannot handle long sense request
correctly and will make the chip refuse to do read/write when requested
long sense.
Add a bad sense quirk for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c5603d2fdb424849360fe7e3f8c1befc97571b8c upstream.
Currently the code will set US_FL_SANE_SENSE flag unconditionally if
device claims SPC3+, however we should allow US_FL_BAD_SENSE flag to
prevent this behavior, because SMI SM3350 UFS-USB bridge controller,
which claims SPC4, will show strange behavior with 96-byte sense
(put the chip into a wrong state that cannot read/write anything).
Check the presence of US_FL_BAD_SENSE when assuming US_FL_SANE_SENSE on
SPC4+ devices.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 34aabf918717dd14e05051896aaecd3b16b53d95 upstream.
Telit 3G Intel based modems require zero packet to be sent if
out data size is equal to the endpoint max packet size.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eafb27fa5283599ce6c5492ea18cf636a28222bb upstream.
Mediatek Preloader is a proprietary embedded boot loader for loading
Little Kernel and Linux into device DRAM.
This boot loader also handle firmware update. Mediatek Preloader will be
enumerated as a virtual COM port when the device is connected to Windows
or Linux OS via CDC-ACM class driver. When the USB enumeration has been
done, Mediatek Preloader will send out handshake command "READY" to PC
actively instead of waiting command from the download tool.
Since Linux 4.12, the commit "tty: reset termios state on device
registration" (93857edd9829e144acb6c7e72d593f6e01aead66) causes Mediatek
Preloader receiving some abnoraml command like "READYXX" as it sent.
This will be recognized as an incorrect response. The behavior change
also causes the download handshake fail. This change only affects
subsequent connects if the reconnected device happens to get the same minor
number.
By disabling the ECHO termios flag could avoid this problem. However, it
cannot be done by user space configuration when download tool open
/dev/ttyACM0. This is because the device running Mediatek Preloader will
send handshake command "READY" immediately once the CDC-ACM driver is
ready.
This patch wants to fix above problem by introducing "DISABLE_ECHO"
property in driver_info. When Mediatek Preloader is connected, the
CDC-ACM driver could disable ECHO flag in termios to avoid the problem.
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Cc: stable@vger.kernel.org
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
r8a66597_endpoint_disable()
commit c85400f886e3d41e69966470879f635a2b50084c upstream.
The function r8a66597_endpoint_disable() and r8a66597_urb_enqueue() may
be concurrently executed.
The two functions both access a possible shared variable "hep->hcpriv".
This shared variable is freed by r8a66597_endpoint_disable() via the
call path:
r8a66597_endpoint_disable
kfree(hep->hcpriv) (line 1995 in Linux-4.19)
This variable is read by r8a66597_urb_enqueue() via the call path:
r8a66597_urb_enqueue
spin_lock_irqsave(&r8a66597->lock)
init_pipe_info
enable_r8a66597_pipe
pipe = hep->hcpriv (line 802 in Linux-4.19)
The read operation is protected by a spinlock, but the free operation
is not protected by this spinlock, thus a concurrency use-after-free bug
may occur.
To fix this bug, the spin-lock and spin-unlock function calls in
r8a66597_endpoint_disable() are moved to protect the free operation.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4b2c01ad902ec02fa962b233decd2f14be3714ba upstream.
Added USB serial option driver support for Fibocom NL678 series cellular
module: VID 2cb7 and PIDs 0x0104 and 0x0105.
Reserved network and ADB interfaces.
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2cb7 ProdID=0104 Rev=03.10
S: Manufacturer=Fibocom
S: Product=Fibocom NL678-E Modem
S: SerialNumber=12345678
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2cb7 ProdID=0105 Rev=03.10
S: Manufacturer=Fibocom
S: Product=Fibocom NL678-E Modem
S: SerialNumber=12345678
C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8d503f206c336677954160ac62f0c7d9c219cd89 upstream.
Add device ids to pl2303 for the HP POS pole displays:
LM920: 03f0:026b
TD620: 03f0:0956
LD960TA: 03f0:4439
LD220TA: 03f0:4349
LM940: 03f0:5039
Signed-off-by: Scott Chen <scott@labau.com.tw>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 28a86092b1753b802ef7e3de8a4c4a69a9c1bb03 upstream.
Added USB serial option driver support for Telit LN940 series cellular
modules. Covering both QMI and MBIM modes.
usb-devices output (0x1900):
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=1900 Rev=03.10
S: Manufacturer=Telit
S: Product=Telit LN940 Mobile Broadband
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
usb-devices output (0x1901):
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 20 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=1901 Rev=03.10
S: Manufacturer=Telit
S: Product=Telit LN940 Mobile Broadband
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 30360224441ce89a98ed627861e735beb4010775 upstream.
Added USB serial option driver support for Fibocom NL668 series cellular
modules. Reserved USB endpoints 4, 5 and 6 for network + ADB interfaces.
usb-devices output (QMI mode)
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1508 ProdID=1001 Rev=03.18
S: Manufacturer=Nodecom NL668 Modem
S: Product=Nodecom NL668-CN Modem
S: SerialNumber=
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
usb-devices output (ECM mode)
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1508 ProdID=1001 Rev=03.18
S: Manufacturer=Nodecom NL668 Modem
S: Product=Nodecom NL668-CN Modem
S: SerialNumber=
C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cc6730df08a291e51e145bc65e24ffb5e2f17ab6 upstream.
Added USB serial option driver support for Simcom SIM7500/SIM7600 series
cellular modules exposing MBIM interface (VID 0x1e0e,PID 0x9003)
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 14 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1e0e ProdID=9003 Rev=03.18
S: Manufacturer=SimTech, Incorporated
S: Product=SimTech, Incorporated
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 5 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#= 6 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d57ec3c83b5153217a70b561d4fb6ed96f2f7a25 upstream.
The HP lt4132 is a rebranded Huawei ME906s-158 LTE modem.
The interface with protocol 0x16 is "CDC ECM & NCM" according to the *.inf
files included with the Windows driver. Attaching the option driver to it
doesn't result in a /dev/ttyUSB* device being created, so I've excluded it.
Note that it is also excluded for corresponding Huawei-branded devices, cf.
commit d544db293a44 ("USB: support new huawei devices in option.c").
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 3
P: Vendor=03f0 ProdID=a31d Rev=01.02
S: Manufacturer=HP Inc.
S: Product=HP lt4132 LTE/HSPA+ 4G Module
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=2mA
I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option
I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option
I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option
I: If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=06 Prot=16 Driver=(none)
I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option
I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 3
P: Vendor=03f0 ProdID=a31d Rev=01.02
S: Manufacturer=HP Inc.
S: Product=HP lt4132 LTE/HSPA+ 4G Module
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 7 Cfg#= 2 Atr=a0 MxPwr=2mA
I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I: If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=06 Prot=00 Driver=cdc_ether
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option
I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option
I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option
I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option
I: If#=0x6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 3
P: Vendor=03f0 ProdID=a31d Rev=01.02
S: Manufacturer=HP Inc.
S: Product=HP lt4132 LTE/HSPA+ 4G Module
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 3 Cfg#= 3 Atr=a0 MxPwr=2mA
I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option
Signed-off-by: Tore Anderson <tore@fud.no>
Cc: stable@vger.kernel.org
[ johan: drop id defines ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 70a7444c550a75584ffcfae95267058817eff6a7 upstream.
Added USB serial option driver support for GosunCn ZTE WeLink ME3630
series cellular modules for USB modes ECM/NCM and MBIM.
usb-devices output MBIM mode:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=0602 Rev=03.18
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
usb-devices output ECM/NCM mode:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 11 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=1476 Rev=03.18
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I: If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 45f750c16cae3625014c14c77bd9005eda975d35 upstream.
The code to prevent a bus suspend if a USB3 port was still in link training
also reacted to USB2 port polling state.
This caused bus suspend to busyloop in some cases.
USB2 polling state is different from USB3, and should not prevent bus
suspend.
Limit the USB3 link training state check to USB3 root hub ports only.
The origial commit went to stable so this need to be applied there as well
Fixes: 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2c2322fbcab8102b8cadc09d66714700a2da42c2 ]
On Palm TE nothing happens when you try to use gadget drivers and plug
the USB cable. Fix by adding the board to the vbus sense quirk list.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6ca6695f576b8453fe68865e84d25946d63b10ad ]
On OMAP 15xx machines there are no transceivers, and omap_udc_start()
always fails as it forgot to adjust the default return value.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 99f700366fcea1aa2fa3c49c99f371670c3c62f8 ]
We currently crash if usb_add_gadget_udc_release() fails, since the
udc->done is not initialized until in the remove function.
Furthermore, on module removal the udc data is accessed although
the release function is already triggered by usb_del_gadget_udc()
early in the function.
Fix by rewriting the release and remove functions, basically moving
all the cleanup into the release function, and doing the completion
only in the module removal case.
The patch fixes omap_udc module probe with a failing gadged, and also
allows the removal of omap_udc. Tested by running "modprobe omap_udc;
modprobe -r omap_udc" in a loop.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 286afdde1640d8ea8916a0f05e811441fbbf4b9d ]
The current code fails to release the third irq on the error path
(observed by reading the code), and we get also multiple WARNs with
failing gadget drivers due to duplicate IRQ releases. Fix by using
devm_request_irq().
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0472bf06c6fd33c1a18aaead4c8f91e5a03d8d7b upstream.
Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.
This is according to xhci 1.1 specification section 4.23.5.2 extra note:
"Software shall ensure that a device is prevented from entering a U-state
where its worst case exit latency approaches the ESIT."
Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 704620afc70cf47abb9d6a1a57f3825d2bca49cf upstream.
When reading an extra descriptor, we need to properly check the minimum
and maximum size allowed, to prevent from invalid data being sent by a
device.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d7859905301880ad3e16272399d26900af3ac496 upstream.
Add another Apple Cinema Display to the list of supported displays.
Signed-off-by: Alexander Theissen <alex.theissen@me.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2f2dde6ba89b1ef1fe23c1138131b315d9aa4019 upstream.
Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.
i.e.,
[ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[ 166.918327] usb usb2-port2: link state change
[ 166.918337] usb usb2-port2: do warm reset
[ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[ 167.276050] usb 2-2: USB disconnect, device number 2
[ 167.276058] usb 2-2: unregistering device
[ 167.276060] usb 2-2: unregistering interface 2-2:1.0
[ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk
[ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...
Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.
Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.
The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.
Signed-off-by: Harry Pan <harry.pan@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7661ca09b2ff98f48693f431bb01fed62830e433 upstream.
gcc-8 points out two comparisons that are clearly bogus
and almost certainly not what the author intended to write:
drivers/usb/gadget/udc/dummy_hcd.c: In function 'set_link_state_by_speed':
drivers/usb/gadget/udc/dummy_hcd.c:379:31: error: bitwise comparison always evaluates to false [-Werror=tautological-compare]
USB_PORT_STAT_ENABLE) == 1 &&
^~
drivers/usb/gadget/udc/dummy_hcd.c:381:25: error: bitwise comparison always evaluates to false [-Werror=tautological-compare]
USB_SS_PORT_LS_U0) == 1 &&
^~
I looked at the code for a bit and came up with a change that makes
it look like what the author probably meant here. This makes it
look reasonable to me and to gcc, shutting up the warning.
It does of course change behavior as the two conditions are actually
evaluated rather than being hardcoded to false, and I have made no
attempt at verifying that the changed logic makes sense in the context
of a USB HCD, so that part needs to be reviewed carefully.
Fixes: 1cd8fd2887e1 ("usb: gadget: dummy_hcd: add SuperSpeed support")
Cc: Tatyana Brokhman <tlinder@codeaurora.org>
Cc: Felipe Balbi <balbi@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit effd14f66cc1ef6701a19c5a56e39c35f4d395a5 upstream.
Cherry G230 Stream 2.0 (G85-231) and 3.0 (G85-232) need this quirk to
function correctly. This fixes a but where double pressing numlock locks
up the device completely with need to replug the keyboard.
Signed-off-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a84a1bcc992f0545a51d2e120b8ca2ef20e2ea97 upstream.
There are two new Realtek card readers require ums-realtek to work
correctly.
Add the new IDs to support them.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 958c0bd86075d4ef1c936998deefe1947e539240 upstream.
Realtek USB3.0 Card Reader [0bda:0328] reports wrong port status on
Cannon lake PCH USB3.1 xHCI [8086:a36d] after resume from S3,
after clear port reset it works fine.
Since this device is registered on USB3 roothub at boot,
when port status reports not superspeed, xhci_get_port_status will call
an uninitialized completion in bus_state[0].
Kernel will hang because of NULL pointer.
Restrict the USB2 resume status check in USB2 roothub to fix hang issue.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
detected
commit 2f31a67f01a8beb22cae754c53522cb61a005750 upstream.
USB3 roothub might autosuspend before a plugged USB3 device is detected,
causing USB3 device enumeration failure.
USB3 devices don't show up as connected and enabled until USB3 link trainig
completes. On a fast booting platform with a slow USB3 link training the
link might reach the connected enabled state just as the bus is suspending.
If this device is discovered first time by the xhci_bus_suspend() routine
it will be put to U3 suspended state like the other ports which failed to
suspend earlier.
The hub thread will notice the connect change and resume the bus,
moving the port back to U0
This U0 -> U3 -> U0 transition right after being connected seems to be
too much for some devices, causing them to first go to SS.Inactive state,
and finally end up stuck in a polling state with reset asserted
Fix this by failing the bus suspend if a port has a connect change or is
in a polling state in xhci_bus_suspend().
Don't do any port changes until all ports are checked, buffer all port
changes and only write them in the end if suspend can proceed
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a5baeaeabcca3244782a9b6382ebab6f8a58f583 upstream.
This definition is used by msecs_to_jiffies in milliseconds.
According to the comments, max rexit timeout should be 20ms.
Align with the comments to properly calculate the delay.
Verified on Sunrise Point-LP and Cannon Lake.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 22454b79e6de05fa61a2a72d00d2eed798abbb75 upstream.
This will clear the USB_PORT_FEAT_C_CONNECTION bit in case of a hub port reset
only if a device is was attached to the hub port before resetting the hub port.
Using a Lenovo T480s attached to the ultra dock it was not possible to detect
some usb-c devices at the dock usb-c ports because the hub_port_reset code
will clear the USB_PORT_FEAT_C_CONNECTION bit after the actual hub port reset.
Using this device combo the USB_PORT_FEAT_C_CONNECTION bit was set between the
actual hub port reset and the clear of the USB_PORT_FEAT_C_CONNECTION bit.
This ends up with clearing the USB_PORT_FEAT_C_CONNECTION bit after the
new device was attached such that it was not detected.
This patch will not clear the USB_PORT_FEAT_C_CONNECTION bit if there is
currently no device attached to the port before the hub port reset.
This will avoid clearing the connection bit for new attached devices.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2278446e2b7cd33ad894b32e7eb63afc7db6c86e upstream.
Hub driver will try to disable a USB3 device twice at logical disconnect,
racing with xhci_free_dev() callback from the first port disable.
This can be triggered with "udisksctl power-off --block-device <disk>"
or by writing "1" to the "remove" sysfs file for a USB3 device
in 4.17-rc4.
USB3 devices don't have a similar disabled link state as USB2 devices,
and use a U3 suspended link state instead. In this state the port
is still enabled and connected.
hub_port_connect() first disconnects the device, then later it notices
that device is still enabled (due to U3 states) it will try to disable
the port again (set to U3).
The xhci_free_dev() called during device disable is async, so checking
for existing xhci->devs[i] when setting link state to U3 the second time
was successful, even if device was being freed.
The regression was caused by, and whole thing revealed by,
Commit 44a182b9d177 ("xhci: Fix use-after-free in xhci_free_virt_device")
which sets xhci->devs[i]->udev to NULL before xhci_virt_dev() returned.
and causes a NULL pointer dereference the second time we try to set U3.
Fix this by checking xhci->devs[i]->udev exists before setting link state.
The original patch went to stable so this fix needs to be applied there as
well.
Fixes: 44a182b9d177 ("xhci: Fix use-after-free in xhci_free_virt_device")
Cc: <stable@vger.kernel.org>
Reported-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Tested-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f6501f49199097b99e4e263644d88c90d1ec1060 upstream.
Add another Apple Cinema Display to the list of supported displays
Signed-off-by: Mattias Jacobsson <2pi@mok.nu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a77112577667cbda7c6292c52d909636aef31fd9 upstream.
Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 LUX RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.
Dmesg output:
usb 1-6: string descriptor 0 read error: -110
usb 1-6: New USB device found, idVendor=1b1c, idProduct=1b33
usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-6: can't set config #1, error -110
Signed-off-by: Emmanuel Pescosta <emmanuelpescosta099@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit deefd24228a172d1b27d4a9adbfd2cdacd60ae64 upstream.
Raydium USB touchscreen fails to set config if LPM is enabled:
[ 2.030658] usb 1-8: New USB device found, idVendor=2386, idProduct=3119
[ 2.030659] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.030660] usb 1-8: Product: Raydium Touch System
[ 2.030661] usb 1-8: Manufacturer: Raydium Corporation
[ 7.132209] usb 1-8: can't set config #1, error -110
Same behavior can be observed on 2386:3114.
Raydium claims the touchscreen supports LPM under Windows, so I used
Microsoft USB Test Tools (MUTT) [1] to check its LPM status. MUTT shows
that the LPM doesn't work under Windows, either. So let's just disable LPM
for Raydium touchscreens.
[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/usb-test-tools
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 63529eaa6164ef7ab4b907b25ac3648177e5e78f upstream.
The cdc-acm kernel module currently does not support the Hiro (Conexant)
H05228 USB modem. The patch below adds the device specific information:
idVendor 0x0572
idProduct 0x1349
Signed-off-by: Maarten Jacobs <maarten256@outlook.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8b97d73c4d72a2abf58f8e49062a7ee1e5f1334e ]
The ChipIdea IRQ is disabled before scheduling the otg work and
re-enabled on otg work completion. However if the job is already
scheduled we have to undo the effect of disable_irq int order to
balance the IRQ disable-depth value.
Fixes: be6b0c1bd0be ("usb: chipidea: using one inline function to cover queue work operations")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 665c365a77fbfeabe52694aedf3446d5f2f1ce42 upstream.
Commit 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more") checks the
transfer flags for URBs submitted from userspace via usbfs. However,
the check for whether the USBDEVFS_URB_SHORT_NOT_OK flag should be
allowed for a control transfer was added in the wrong place, before
the code has properly determined the direction of the control
transfer. (Control transfers are special because for them, the
direction is set by the bRequestType byte of the Setup packet rather
than direction bit of the endpoint address.)
This patch moves code which sets up the allow_short flag for control
transfers down after is_in has been set to the correct value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+24a30223a4b609bb802e@syzkaller.appspotmail.com
Fixes: 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more")
CC: Oliver Neukum <oneukum@suse.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9ae24af3669111d418242caec8dd4ebd9ba26860 upstream.
num can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/usb/gadget/function/f_mass_storage.c:3177 fsg_lun_make() warn:
potential spectre issue 'fsg_opts->common->luns' [r] (local cap)
Fix this by sanitizing num before using it to index
fsg_opts->common->luns
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Felipe Balbi <felipe.balbi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f976d0e5747ca65ccd0fb2a4118b193d70aa1836 upstream.
The usb standard ("Universal Serial Bus Class Definitions for Communication
Devices") distiguishes between "consistent signals" (DSR, DCD), and
"irregular signals" (break, ring, parity error, framing error, overrun).
The bits of "irregular signals" are set, if this error/event occurred on
the device side and are immeadeatly unset, if the serial state notification
was sent.
Like other drivers of real serial ports do, just the occurence of those
events should be counted in serial_icounter_struct (but no 1->0
transitions).
Signed-off-by: Tobias Herzog <t-herzog@gmx.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0ae99ecba7928c7bc66cf14d8a88f0b6ec9fc78e ]
platform_get_irq() returns an error code, but the dwc3-omap driver
ignores it and always returns -EINVAL. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 99dbff202e28ad1dadf55b058bcae7908678e963 ]
platform_get_irq() returns an error code, but the ehci-omap driver
ignores it and always returns -ENODEV. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Also, notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 46edf52d08342b3dc1f9a61c5200ab8b1c0f5a37 ]
platform_get_irq() returns an error code, but the imx21-hcd driver
ignores it and always returns -ENXIO. This is not correct, and
prevents -EPROBE_DEFER from being propagated properly.
Notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af
Print error message and propagate the return value of platform_get_irq
on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a4fd4a724d6c30ad671046d83be2e9be2f11d275 ]
Ever since commit a621bac3044e ("scsi_lib: correctly retry failed zero
length REQ_TYPE_FS commands"), people have been getting bogus error
messages for USB disk drives using ATA pass-thru. For example:
[ 1344.880193] sd 6:0:0:0: [sdb] Attached SCSI disk
[ 1345.069152] sd 6:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 1345.069159] sd 6:0:0:0: [sdb] tag#0 Sense Key : Hardware Error [current] [descriptor]
[ 1345.069162] sd 6:0:0:0: [sdb] tag#0 Add. Sense: No additional sense information
[ 1345.069168] sd 6:0:0:0: [sdb] tag#0 CDB: ATA command pass through(16) 85 06 20 00 00 00 00 00 00 00 00 00 00 00 e5 00
[ 1345.172252] sd 6:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 1345.172258] sd 6:0:0:0: [sdb] tag#0 Sense Key : Hardware Error [current] [descriptor]
[ 1345.172261] sd 6:0:0:0: [sdb] tag#0 Add. Sense: No additional sense information
[ 1345.172266] sd 6:0:0:0: [sdb] tag#0 CDB: ATA command pass through(12)/Blank a1 06 20 da 00 00 4f c2 00 b0 00 00
These messages can be quite annoying, because programs like udisks2
provoke them every 10 minutes or so. Other programs can also have
this effect, such as those in smartmontools.
I don't fully understand how that commit induced the SCSI core to log
these error messages, but the underlying cause for them is code added
to usb-storage by commit f1a0743bc0e7 ("USB: storage: When a device
returns no sense data, call it a Hardware Error"). At the time it was
necessary to do this, in order to prevent an infinite retry loop with
some not-so-great mass storage devices.
However, the ATA pass-thru protocol uses SCSI sense data to return
command status values, and some devices always report Check Condition
status for ATA pass-thru commands to ensure that the host retrieves
the sense data, even if the command succeeded. This violates the USB
mass-storage protocol (Check Condition status is supposed to mean the
command failed), but we can't help that.
This patch attempts to mitigate the problem of these bogus error
reports by changing usb-storage. The HARDWARE ERROR sense key will be
inserted only for commands that aren't ATA pass-thru.
Thanks to Ewan Milne for pointing out that this mechanism was present
in usb-storage. 8 years after writing it, I had completely forgotten
its existence.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Kris Lindgren <kris.lindgren@gmail.com>
Ref: https://bugzilla.redhat.com/show_bug.cgi?id=1351305
CC: Ewan D. Milne <emilne@redhat.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit daa35bd95634a2a2d72d1049c93576a02711cb1a upstream.
When the gadget serial device has no associated TTY, do not pass any
received data into the TTY layer for processing; simply drop it instead.
This prevents the TTY layer from calling back into the gadget serial
driver, which will then crash in e.g. gs_write_room() due to lack of
gadget serial device to TTY association (i.e. a NULL pointer dereference).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1208d8a84fdcae6b395c57911cdf907450d30e70 upstream.
When disabling a USB3 port the hub driver will set the port link state to
U3 to prevent "ejected" or "safely removed" devices that are still
physically connected from immediately re-enumerating.
If the device was really unplugged, then error messages were printed
as the hub tries to set the U3 link state for a port that is no longer
enabled.
xhci-hcd ee000000.usb: Cannot set link state.
usb usb8-port1: cannot disable (err = -32)
Don't print error message in xhci-hub if hub tries to set port link state
for a disabled port. Return -ENODEV instead which also silences hub driver.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ross Zwisler <zwisler@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f5fad711c06e652f90f581fc7c2caee327c33d31 upstream.
Add device-id for the Motorola Tetra radio MTP6550.
Bus 001 Device 004: ID 0cad:9012 Motorola CGISS
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0cad Motorola CGISS
idProduct 0x9012
bcdDevice 24.16
iManufacturer 1 Motorola Solutions, Inc.
iProduct 2 TETRA PEI interface
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 55
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 3 Generic Serial config
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Reported-by: Hans Hult <hanshult35@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ffe84e01bb1b38c7eb9c6b6da127a6c136d251df upstream.
The workaround for missing CAS bit is also needed for xHC on Intel
sunrisepoint PCH. For more details see:
Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 14427b86837a4baf1c121934c6599bdb67dfa9fc ]
snprintf() always returns the full length of the string it could have
printed, even if it was truncated because the buffer was too small.
So in case the counter value is truncated, we will over-read from
in_buffer and over-write to the caller's buffer.
I don't think it's actually possible for this to happen, but in case
truncation occurs, WARN and return -EIO.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c37bd52836296ecc9a0fc8060b819089aebdbcde ]
There is no deallocation of fotg210->ep[i] elements, allocated at
fotg210_udc_probe.
The patch adds deallocation of fotg210->ep array elements and simplifies
error path of fotg210_udc_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c183813fcee44a249339b7c46e1ad271ca1870aa upstream.
usb_driver_claim_interface() disables and re-enables Link Power
Management, but it shouldn't do either one, for the reasons listed
below. This patch removes the two LPM-related function calls from the
routine.
The reason for disabling LPM in the analogous function
usb_probe_interface() is so that drivers won't have to deal with
unwanted LPM transitions in their probe routine. But
usb_driver_claim_interface() doesn't call the driver's probe routine
(or any other callbacks), so that reason doesn't apply here.
Furthermore, no driver other than usbfs will ever call
usb_driver_claim_interface() unless it is already bound to another
interface in the same device, which means disabling LPM here would be
redundant. usbfs doesn't interact with LPM at all.
Lastly, the error return from usb_unlocked_disable_lpm() isn't handled
properly; the code doesn't clean up its earlier actions before
returning.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 8306095fd2c1 ("USB: Disable USB 3.0 LPM in critical sections.")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
service_outstanding_interrupt()"
commit e871db8d78df1c411032cbb3acfdf8930509360e upstream.
This reverts commit 6e22e3af7bb3a7b9dc53cb4687659f6e63fca427.
The bug the patch describes to, has been already fixed in commit
2df6948428542 ("USB: cdc-wdm: don't enable interrupts in USB-giveback")
so need to this, revert it.
Fixes: 6e22e3af7bb3 ("usb: cdc-wdm: Fix a sleep-in-atomic-context bug in service_outstanding_interrupt()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|