| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When in dual role mode (dr_mode == USB_DR_MODE_OTG), platform probe
successively basically calls:
- dwc2_gadget_init()
- dwc2_hcd_init()
- dwc2_lowlevel_hw_disable() since recent change [1]
- usb_add_gadget_udc()
The PHYs (and so the clocks it may provide) shouldn't be disabled for all
SoCs, in OTG mode, as the HCD part has been initialized.
On STM32 this creates some weird race condition upon boot, when:
- initially attached as a device, to a HOST
- and there is a gadget script invoked to setup the device part.
Below issue becomes systematic, as long as the gadget script isn't
started by userland: the hardware PHYs (and so the clocks provided by the
PHYs) remains disabled.
It ends up in having an endless interrupt storm, before the watchdog
resets the platform.
[ 16.924163] dwc2 49000000.usb-otg: EPs: 9, dedicated fifos, 952 entries in SPRAM
[ 16.962704] dwc2 49000000.usb-otg: DWC OTG Controller
[ 16.966488] dwc2 49000000.usb-otg: new USB bus registered, assigned bus number 2
[ 16.974051] dwc2 49000000.usb-otg: irq 77, io mem 0x49000000
[ 17.032170] hub 2-0:1.0: USB hub found
[ 17.042299] hub 2-0:1.0: 1 port detected
[ 17.175408] dwc2 49000000.usb-otg: Mode Mismatch Interrupt: currently in Host mode
[ 17.181741] dwc2 49000000.usb-otg: Mode Mismatch Interrupt: currently in Host mode
[ 17.189303] dwc2 49000000.usb-otg: Mode Mismatch Interrupt: currently in Host mode
...
The host part is also not functional, until the gadget part is configured.
The HW may only be disabled for peripheral mode (original init), e.g.
dr_mode == USB_DR_MODE_PERIPHERAL, until the gadget driver initializes.
But when in USB_DR_MODE_OTG, the HW should remain enabled, as the HCD part
is able to run, while the gadget part isn't necessarily configured.
I don't fully get the of purpose the original change, that claims disabling
the hardware is missing. It creates conditions on SOCs using the PHY
initialization to be completely non working in OTG mode. Original
change [1] should be reworked to be platform specific.
[1] https://lore.kernel.org/r/20221206-dwc2-gadget-dual-role-v1-2-36515e1092cd@theobroma-systems.com
Fixes: ade23d7b7ec5 ("usb: dwc2: power on/off phy for peripheral mode in dual-role mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Tested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20230315144433.3095859-1-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Each time the platform goes to low power, PM suspend / resume routines
call: __dwc2_lowlevel_hw_enable -> devm_add_action_or_reset().
This adds a new devres each time.
This may also happen at runtime, as dwc2_lowlevel_hw_enable() can be
called from udc_start().
This can be seen with tracing:
- echo 1 > /sys/kernel/debug/tracing/events/dev/devres_log/enable
- go to low power
- cat /sys/kernel/debug/tracing/trace
A new "ADD" entry is found upon each low power cycle:
... devres_log: 49000000.usb-otg ADD 82a13bba devm_action_release (8 bytes)
... devres_log: 49000000.usb-otg ADD 49889daf devm_action_release (8 bytes)
...
A second issue is addressed here:
- regulator_bulk_enable() is called upon each PM cycle (suspend/resume).
- regulator_bulk_disable() never gets called.
So the reference count for these regulators constantly increase, by one
upon each low power cycle, due to missing regulator_bulk_disable() call
in __dwc2_lowlevel_hw_disable().
The original fix that introduced the devm_add_action_or_reset() call,
fixed an issue during probe, that happens due to other errors in
dwc2_driver_probe() -> dwc2_core_reset(). Then the probe fails without
disabling regulators, when dr_mode == USB_DR_MODE_PERIPHERAL.
Rather fix the error path: disable all the low level hardware in the
error path, by using the "hsotg->ll_hw_enabled" flag. Checking dr_mode
has been introduced to avoid a dual call to dwc2_lowlevel_hw_disable().
"ll_hw_enabled" should achieve the same (and is used currently in the
remove() routine).
Fixes: 54c196060510 ("usb: dwc2: Always disable regulators on driver teardown")
Fixes: 33a06f1300a7 ("usb: dwc2: Fix error path in gadget registration")
Cc: stable <stable@kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20230316084127.126084-1-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The user may call role_store() when driver is handling
ci_handle_id_switch() which is triggerred by otg event or power lost
event. Unfortunately, the controller may go into chaos in this case.
Fix this by protecting it with mutex lock.
Fixes: a932a8041ff9 ("usb: chipidea: core: add sysfs group")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20230317061516.2451728-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
current role
It should not return -EINVAL if the request role is the same with current
role, return non-error and without do anything instead.
Fixes: a932a8041ff9 ("usb: chipidea: core: add sysfs group")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20230317061516.2451728-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
WebUSB code uses wLength directly without proper endianness conversion.
Update it to use already prepared temporary variable w_length instead.
Fixes: 93c473948c58 ("usb: gadget: add WebUSB landing page support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-By: Jó Ágila Bitsch <jgilab@gmail.com>
Link: https://lore.kernel.org/r/20230313154522.52684-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Just like other JMicron JMS5xx enclosures, it chokes on report-opcodes,
let's avoid them.
Signed-off-by: Yaroslav Furman <yaro330@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230312090745.47962-1-yaro330@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Patch changes CDNS_DEVICE_ID in USBSSP PCI Glue driver to remove
the conflict with Cadence USBSS driver.
cc: <stable@vger.kernel.org>
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20230309063048.299378-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PCI based platform can have more than two PCI functions.
USBSS PCI Glue driver during initialization should
consider only DRD/HOST/DEVICE PCI functions and
all other should be ignored. This patch adds additional
condition which causes that only DRD and HOST/DEVICE
function will be accepted.
cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20230308124427.311245-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In some cases, driver trees to send Status Stage twice.
The first one from upper layer of gadget usb subsystem and
second time from controller driver.
This patch fixes this issue and remove tricky handling of
SET_INTERFACE from controller driver which is no longer
needed.
cc: <stable@vger.kernel.org>
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20230307111420.376056-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some boards might use USB-A female connector for USB ports, however,
the port could be connected to a dual-mode USB controller, making it
also behaves as a peripheral device if male-to-male cable is connected.
In this case, the dts looks like this:
&usb0 {
status = "okay";
dr_mode = "otg";
usb-role-switch;
role-switch-default-mode = "host";
};
After boot, dwc2_ovr_init() sets GOTGCTL to GOTGCTL_AVALOVAL and call
dwc2_force_mode() with parameter host=false, which causes inconsistent
mode - The hardware is in peripheral mode while the kernel status is
in host mode.
What we can do now is to call dwc2_drd_role_sw_set() to switch to
device mode, and everything should work just fine now, even switching
back to none(default) mode afterwards.
Fixes: e14acb876985 ("usb: dwc2: drd: add role-switch-default-node support")
Cc: stable <stable@kernel.org>
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Tested-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/SG2PR01MB204837BF68EDB0E343D2A375C9A59@SG2PR01MB2048.apcprd01.prod.exchangelabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since both source and sink device can send discover_identity message in
PD3, kernel may dump below warning:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 169 at drivers/usb/typec/tcpm/tcpm.c:1446 tcpm_queue_vdm+0xe0/0xf0
Modules linked in:
CPU: 0 PID: 169 Comm: 1-0050 Not tainted 6.1.1-00038-g6a3c36cf1da2-dirty #567
Hardware name: NXP i.MX8MPlus EVK board (DT)
pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : tcpm_queue_vdm+0xe0/0xf0
lr : tcpm_queue_vdm+0x2c/0xf0
sp : ffff80000c19bcd0
x29: ffff80000c19bcd0 x28: 0000000000000001 x27: ffff0000d11c8ab8
x26: ffff0000d11cc000 x25: 0000000000000000 x24: 00000000ff008081
x23: 0000000000000001 x22: 00000000ff00a081 x21: ffff80000c19bdbc
x20: 0000000000000000 x19: ffff0000d11c8080 x18: ffffffffffffffff
x17: 0000000000000000 x16: 0000000000000000 x15: ffff0000d716f580
x14: 0000000000000001 x13: ffff0000d716f507 x12: 0000000000000001
x11: 0000000000000000 x10: 0000000000000020 x9 : 00000000000ee098
x8 : 00000000ffffffff x7 : 000000000000001c x6 : ffff0000d716f580
x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000
x2 : ffff80000c19bdbc x1 : 00000000ff00a081 x0 : 0000000000000004
Call trace:
tcpm_queue_vdm+0xe0/0xf0
tcpm_pd_rx_handler+0x340/0x1ab0
kthread_worker_fn+0xcc/0x18c
kthread+0x10c/0x110
ret_from_fork+0x10/0x20
---[ end trace 0000000000000000 ]---
Below sequences may trigger this warning:
tcpm_send_discover_work(work)
tcpm_send_vdm(port, USB_SID_PD, CMD_DISCOVER_IDENT, NULL, 0);
tcpm_queue_vdm(port, header, data, count);
port->vdm_state = VDM_STATE_READY;
vdm_state_machine_work(work);
<-- received discover_identity from partner
vdm_run_state_machine(port);
port->vdm_state = VDM_STATE_SEND_MESSAGE;
mod_vdm_delayed_work(port, x);
tcpm_pd_rx_handler(work);
tcpm_pd_data_request(port, msg);
tcpm_handle_vdm_request(port, msg->payload, cnt);
tcpm_queue_vdm(port, response[0], &response[1], rlen - 1);
--> WARN_ON(port->vdm_state > VDM_STATE_DONE);
For this case, the state machine could still send out discover
identity message later if we skip current discover_identity message.
So we should handle the received message firstly and override the pending
discover_identity message without warning in this case. Then, a delayed
send_discover work will send discover_identity message again.
Fixes: e00943e91678 ("usb: typec: tcpm: PD3.0 sinks can send Discover Identity even in device mode")
cc: <stable@vger.kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230216031515.4151117-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The kernel will dump in the below cases:
sysfs: cannot create duplicate filename
'/devices/virtual/usb_power_delivery/pd1/source-capabilities'
1. After soft reset has completed, an Explicit Contract negotiation occurs.
The sink device will receive source capabilitys again. This will cause
a duplicate source-capabilities file be created.
2. Power swap twice on a device that is initailly sink role.
This will unregister existing capabilities when above cases occurs.
Fixes: 8203d26905ee ("usb: typec: tcpm: Register USB Power Delivery Capabilities")
cc: <stable@vger.kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230215054951.238394-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the unbind callback for f_uac1 and f_uac2, a call to snd_card_free()
via g_audio_cleanup() will disconnect the card and then wait for all
resources to be released, which happens when the refcount falls to zero.
Since userspace can keep the refcount incremented by not closing the
relevant file descriptor, the call to unbind may block indefinitely.
This can cause a deadlock during reboot, as evidenced by the following
blocked task observed on my machine:
task:reboot state:D stack:0 pid:2827 ppid:569 flags:0x0000000c
Call trace:
__switch_to+0xc8/0x140
__schedule+0x2f0/0x7c0
schedule+0x60/0xd0
schedule_timeout+0x180/0x1d4
wait_for_completion+0x78/0x180
snd_card_free+0x90/0xa0
g_audio_cleanup+0x2c/0x64
afunc_unbind+0x28/0x60
...
kernel_restart+0x4c/0xac
__do_sys_reboot+0xcc/0x1ec
__arm64_sys_reboot+0x28/0x30
invoke_syscall+0x4c/0x110
...
The issue can also be observed by opening the card with arecord and
then stopping the process through the shell before unbinding:
# arecord -D hw:UAC2Gadget -f S32_LE -c 2 -r 48000 /dev/null
Recording WAVE '/dev/null' : Signed 32 bit Little Endian, Rate 48000 Hz, Stereo
^Z[1]+ Stopped arecord -D hw:UAC2Gadget -f S32_LE -c 2 -r 48000 /dev/null
# echo gadget.0 > /sys/bus/gadget/drivers/configfs-gadget/unbind
(observe that the unbind command never finishes)
Fix the problem by using snd_card_free_when_closed() instead, which will
still disconnect the card as desired, but defer the task of freeing the
resources to the core once userspace closes its file descriptor.
Fixes: 132fcb460839 ("usb: gadget: Add Audio Class 2.0 Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Reviewed-by: John Keeping <john@metanate.com>
Link: https://lore.kernel.org/r/20230302163648.3349669-1-alvin@pqrs.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for Microchip USB2517 USB 2.0 hub to the onboard usb hub
driver. Adopt the generic usb-device compatible ("usbVID,PID").
This hub has the same reset timings as USB2514, so reuse that one.
There is also an USB2517I which just has industrial temperature range.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: stable <stable@kernel.org>
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20230223073920.2912298-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Previously, there was a 100uS delay inserted after issuing an end transfer
command for specific controller revisions. This was due to the fact that
there was a GUCTL2 bit field which enabled synchronous completion of the
end transfer command once the CMDACT bit was cleared in the DEPCMD
register. Since this bit does not exist for all controller revisions and
the current implementation heavily relies on utizling the EndTransfer
command completion interrupt, add the delay back in for uses where the
interrupt on completion bit is not set, and increase the duration to 1ms
for the controller to complete the command.
An issue was seen where the USB request buffer was unmapped while the DWC3
controller was still accessing the TRB. However, it was confirmed that the
end transfer command was successfully submitted. (no end transfer timeout)
In situations, such as dwc3_gadget_soft_disconnect() and
__dwc3_gadget_ep_disable(), the dwc3_remove_request() is utilized, which
will issue the end transfer command, and follow up with
dwc3_gadget_giveback(). At least for the USB ep disable path, it is
required for any pending and started requests to be completed and returned
to the function driver in the same context of the disable call. Without
the GUCTL2 bit, it is not ensured that the end transfer is completed before
the buffers are unmapped.
Fixes: cf2f8b63f7f1 ("usb: dwc3: gadget: Remove END_TRANSFER delay")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230306200557.29387-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix a typo inside the dwc3 struct docs.
Fixes: 63d7f9810a38 ("usb: dwc3: core: Enable GUCTL1 bit 10 for fixing termination error after resume bug")
Signed-off-by: Vincenzo Palazzo <vincenzopalazzodev@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230302150706.229008-1-vincenzopalazzodev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 130a96d698d7 ("usb: typec: ucsi: acpi: Increase command
completion timeout value") increased the timeout from 5 seconds
to 60 seconds due to issues related to alternate mode discovery.
After the alternate mode discovery switch to polled mode
the timeout was reduced, but instead of being set back to
5 seconds it was reduced to 1 second.
This is causing problems when using a Lenovo ThinkPad X1 yoga gen7
connected over Type-C to a LG 27UL850-W (charging DP over Type-C).
When the monitor is already connected at boot the following error
is logged: "PPM init failed (-110)", /sys/class/typec is empty and
on unplugging the NULL pointer deref fixed earlier in this series
happens.
When the monitor is connected after boot the following error
is logged instead: "GET_CONNECTOR_STATUS failed (-110)".
Setting the timeout back to 5 seconds fixes both cases.
Fixes: e08065069fc7 ("usb: typec: ucsi: acpi: Reduce the command completion timeout")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230308154244.722337-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ucsi_init() which runs from a workqueue sets ucsi->connector and
on an error will clear it again.
ucsi->connector gets dereferenced by ucsi_resume(), this checks for
ucsi->connector being NULL in case ucsi_init() has not finished yet;
or in case ucsi_init() has failed.
ucsi_init() setting ucsi->connector and then clearing it again on
an error creates a race where the check in ucsi_resume() may pass,
only to have ucsi->connector free-ed underneath it when ucsi_init()
hits an error.
Fix this race by making ucsi_init() store the connector array in
a local variable and only assign it to ucsi->connector on success.
Fixes: bdc62f2bae8f ("usb: typec: ucsi: Simplified registration and I/O API")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230308154244.722337-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When ucsi_init() fails, ucsi->connector is NULL, yet in case of
ucsi_acpi we may still get events which cause the ucs_acpi code to call
ucsi_connector_change(), which then derefs the NULL ucsi->connector
pointer.
Fix this by not setting ucsi->ntfy inside ucsi_init() until ucsi_init()
has succeeded, so that ucsi_connector_change() ignores the events
because UCSI_ENABLE_NTFY_CONNECTOR_CHANGE is not set in the ntfy mask.
Fixes: bdc62f2bae8f ("usb: typec: ucsi: Simplified registration and I/O API")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217106
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230308154244.722337-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"This features a bunch of new device support, a couple of new drivers,
yaml conversion and updates of a few drivers.
Core support:
- New devm_of_phy_optional_get() API with users and conversion
New hardware support:
- Mediatek MT7986 phy support
- Qualcomm SM8550 UFS, PCIe, combo phy support, SM6115 / SM4250 USB3
phy support, SM6350 combo phy support, SM6125 UFS PHY support amd
SM8350 & SM8450 combo phy support
- Qualcomm SNPS eUSB2 eUSB2 repeater drivers
- Allwinner F1C100s USB PHY support
- Tegra xusb support for Tegra234
Updates:
- Yaml conversion for Qualcomm pcie2 phy and usb-hsic-phy
- G4 mode support in Qualcomm UFS phy and support for various SoCs
- Yaml conversion for Meson usb2 phy
- TI Type C support for usb phy for j721
- Yaml conversion for Tegra xusb binding"
* tag 'phy-for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (106 commits)
phy: qcom: phy-qcom-snps-eusb2: Add support for eUSB2 repeater
phy: qcom: Add QCOM SNPS eUSB2 repeater driver
dt-bindings: phy: qcom,snps-eusb2-phy: Add phys property for the repeater
dt-bindings: phy: Add qcom,snps-eusb2-repeater schema file
dt-bindings: phy: amlogic,g12a-usb3-pcie-phy: add missing optional phy-supply property
phy: rockchip-typec: Fix unsigned comparison with less than zero
phy: rockchip-typec: fix tcphy_get_mode error case
phy: qcom: snps-eusb2: Add missing headers
phy: qcom-qmp-combo: Add support for SM8550
phy: qcom-qmp: Add v6 DP register offsets
phy: qcom-qmp: pcs-usb: Add v6 register offsets
dt-bindings: phy: qcom,sc8280xp-qmp-usb43dp: Document SM8550 compatible
phy: qcom: Add QCOM SNPS eUSB2 driver
dt-bindings: phy: Add qcom,snps-eusb2-phy schema file
phy: qcom-qmp-pcie: Add support for SM8550 g3x2 and g4x2 PCIEs
phy: qcom-qmp: qserdes-lane-shared: Add v6 register offsets
phy: qcom-qmp: qserdes-txrx: Add v6.20 register offsets
phy: qcom-qmp: pcs-pcie: Add v6.20 register offsets
phy: qcom-qmp: pcs-pcie: Add v6 register offsets
phy: qcom-qmp: pcs: Add v6.20 register offsets
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (143 commits)
tty: n_gsm: add keep alive support
serial: imx: remove a redundant check
dt-bindings: serial: snps-dw-apb-uart: add dma & dma-names properties
soc: qcom: geni-se: Move qcom-geni-se.h to linux/soc/qcom/geni-se.h
tty: n_gsm: add TIOCMIWAIT support
tty: n_gsm: add RING/CD control support
tty: n_gsm: mark unusable ioctl structure fields accordingly
serial: imx: get rid of registers shadowing
serial: imx: refine local variables in rxint()
serial: imx: stop using USR2 in FIFO reading loop
serial: imx: remove redundant USR2 read from FIFO reading loop
serial: imx: do not break from FIFO reading loop prematurely
serial: imx: do not sysrq broken chars
serial: imx: work-around for hardware RX flood
serial: imx: factor-out common code to imx_uart_soft_reset()
serial: 8250_pci1xxxx: Add power management functions to quad-uart driver
serial: 8250_pci1xxxx: Add RS485 support to quad-uart driver
serial: 8250_pci1xxxx: Add driver for quad-uart support
serial: 8250_pci: Add serial8250_pci_setup_port definition in 8250_pcilib.c
tty: pcn_uart: fix memory leak with using debugfs_lookup()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt driver updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for 6.3-rc1.
Nothing major in here, just lots of good development, including:
- Thunderbolt additions for new device support and features
- xhci driver updates and cleanups
- USB gadget media driver updates (includes media core changes that
were acked by the v4l2 maintainers)
- lots of other USB gadget driver updates for new features
- dwc3 driver updates and fixes
- minor debugfs leak fixes
- typec driver updates and additions
- dt-bindings conversions to yaml
- other small bugfixes and driver updates
All have been in linux-next for a while with no reported issues"
* tag 'usb-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (237 commits)
usb: dwc3: xilinx: Remove unused of_gpio,h
usb: typec: pd: Add higher capability sysfs for sink PDO
usb: typec: pd: Remove usb_suspend_supported sysfs from sink PDO
usb: dwc3: pci: add support for the Intel Meteor Lake-M
usb: gadget: u_ether: Don't warn in gether_setup_name_default()
usb: gadget: u_ether: Convert prints to device prints
usb: gadget: u_serial: Add null pointer check in gserial_resume
usb: gadget: uvc: fix missing mutex_unlock() if kstrtou8() fails
xhci: host: potential NULL dereference in xhci_generic_plat_probe()
dt-bindings: usb: amlogic,meson-g12a-usb-ctrl: make G12A usb3-phy0 optional
usb: host: fsl-mph-dr-of: reuse device_set_of_node_from_dev
of: device: Do not ignore error code in of_device_uevent_modalias
of: device: Ignore modalias of reused nodes
usb: gadget: configfs: Fix set but not used variable warning
usb: gadget: uvc: Use custom strings if available
usb: gadget: uvc: Allow linking function to string descs
usb: gadget: uvc: Pick up custom string descriptor IDs
usb: gadget: uvc: Allow linking XUs to string descriptors
usb: gadget: configfs: Attach arbitrary strings to cdev
usb: gadget: configfs: Support arbitrary string descriptors
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
- Daniel Verkamp has contributed a memfd series ("mm/memfd: add
F_SEAL_EXEC") which permits the setting of the memfd execute bit at
memfd creation time, with the option of sealing the state of the X
bit.
- Peter Xu adds a patch series ("mm/hugetlb: Make huge_pte_offset()
thread-safe for pmd unshare") which addresses a rare race condition
related to PMD unsharing.
- Several folioification patch serieses from Matthew Wilcox, Vishal
Moola, Sidhartha Kumar and Lorenzo Stoakes
- Johannes Weiner has a series ("mm: push down lock_page_memcg()")
which does perform some memcg maintenance and cleanup work.
- SeongJae Park has added DAMOS filtering to DAMON, with the series
"mm/damon/core: implement damos filter".
These filters provide users with finer-grained control over DAMOS's
actions. SeongJae has also done some DAMON cleanup work.
- Kairui Song adds a series ("Clean up and fixes for swap").
- Vernon Yang contributed the series "Clean up and refinement for maple
tree".
- Yu Zhao has contributed the "mm: multi-gen LRU: memcg LRU" series. It
adds to MGLRU an LRU of memcgs, to improve the scalability of global
reclaim.
- David Hildenbrand has added some userfaultfd cleanup work in the
series "mm: uffd-wp + change_protection() cleanups".
- Christoph Hellwig has removed the generic_writepages() library
function in the series "remove generic_writepages".
- Baolin Wang has performed some maintenance on the compaction code in
his series "Some small improvements for compaction".
- Sidhartha Kumar is doing some maintenance work on struct page in his
series "Get rid of tail page fields".
- David Hildenbrand contributed some cleanup, bugfixing and
generalization of pte management and of pte debugging in his series
"mm: support __HAVE_ARCH_PTE_SWP_EXCLUSIVE on all architectures with
swap PTEs".
- Mel Gorman and Neil Brown have removed the __GFP_ATOMIC allocation
flag in the series "Discard __GFP_ATOMIC".
- Sergey Senozhatsky has improved zsmalloc's memory utilization with
his series "zsmalloc: make zspage chain size configurable".
- Joey Gouly has added prctl() support for prohibiting the creation of
writeable+executable mappings.
The previous BPF-based approach had shortcomings. See "mm: In-kernel
support for memory-deny-write-execute (MDWE)".
- Waiman Long did some kmemleak cleanup and bugfixing in the series
"mm/kmemleak: Simplify kmemleak_cond_resched() & fix UAF".
- T.J. Alumbaugh has contributed some MGLRU cleanup work in his series
"mm: multi-gen LRU: improve".
- Jiaqi Yan has provided some enhancements to our memory error
statistics reporting, mainly by presenting the statistics on a
per-node basis. See the series "Introduce per NUMA node memory error
statistics".
- Mel Gorman has a second and hopefully final shot at fixing a CPU-hog
regression in compaction via his series "Fix excessive CPU usage
during compaction".
- Christoph Hellwig does some vmalloc maintenance work in the series
"cleanup vfree and vunmap".
- Christoph Hellwig has removed block_device_operations.rw_page() in
ths series "remove ->rw_page".
- We get some maple_tree improvements and cleanups in Liam Howlett's
series "VMA tree type safety and remove __vma_adjust()".
- Suren Baghdasaryan has done some work on the maintainability of our
vm_flags handling in the series "introduce vm_flags modifier
functions".
- Some pagemap cleanup and generalization work in Mike Rapoport's
series "mm, arch: add generic implementation of pfn_valid() for
FLATMEM" and "fixups for generic implementation of pfn_valid()"
- Baoquan He has done some work to make /proc/vmallocinfo and
/proc/kcore better represent the real state of things in his series
"mm/vmalloc.c: allow vread() to read out vm_map_ram areas".
- Jason Gunthorpe rationalized the GUP system's interface to the rest
of the kernel in the series "Simplify the external interface for
GUP".
- SeongJae Park wishes to migrate people from DAMON's debugfs interface
over to its sysfs interface. To support this, we'll temporarily be
printing warnings when people use the debugfs interface. See the
series "mm/damon: deprecate DAMON debugfs interface".
- Andrey Konovalov provided the accurately named "lib/stackdepot: fixes
and clean-ups" series.
- Huang Ying has provided a dramatic reduction in migration's TLB flush
IPI rates with the series "migrate_pages(): batch TLB flushing".
- Arnd Bergmann has some objtool fixups in "objtool warning fixes".
* tag 'mm-stable-2023-02-20-13-37' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (505 commits)
include/linux/migrate.h: remove unneeded externs
mm/memory_hotplug: cleanup return value handing in do_migrate_range()
mm/uffd: fix comment in handling pte markers
mm: change to return bool for isolate_movable_page()
mm: hugetlb: change to return bool for isolate_hugetlb()
mm: change to return bool for isolate_lru_page()
mm: change to return bool for folio_isolate_lru()
objtool: add UACCESS exceptions for __tsan_volatile_read/write
kmsan: disable ftrace in kmsan core code
kasan: mark addr_has_metadata __always_inline
mm: memcontrol: rename memcg_kmem_enabled()
sh: initialize max_mapnr
m68k/nommu: add missing definition of ARCH_PFN_OFFSET
mm: percpu: fix incorrect size in pcpu_obj_full_size()
maple_tree: reduce stack usage with gcc-9 and earlier
mm: page_alloc: call panic() when memoryless node allocation fails
mm: multi-gen LRU: avoid futile retries
migrate_pages: move THP/hugetlb migration support check to simplify code
migrate_pages: batch flushing TLB
migrate_pages: share more code between _unmap and _move
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC boardfile updates from Arnd Bergmann
"Unused boardfile removal for 6.3
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate
subsystem trees, but the majority is in the same branch, in order to
better handle dependencies between the patches and avoid breaking
bisection.
Unfortunately that leads to merge conflicts against other changes in
the subsystem trees, but they should all be trivial to resolve by
removing the files.
See commit 7d0d3fa7339e ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed.
The only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users"
* tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (91 commits)
mmc: omap: drop TPS65010 dependency
ARM: pxa: restore mfp-pxa320.h
usb: ohci-omap: avoid unused-variable warning
ARM: debug: remove references in DEBUG_UART_8250_SHIFT to removed configs
ARM: s3c: remove obsolete s3c-cpu-freq header
MAINTAINERS: adjust SAMSUNG SOC CLOCK DRIVERS after s3c24xx support removal
MAINTAINERS: update file entries after arm multi-platform rework and mach-pxa removal
ARM: remove CONFIG_UNUSED_BOARD_FILES
mfd: remove htc-pasic3 driver
w1: remove ds1wm driver
usb: remove ohci-tmio driver
fbdev: remove w100fb driver
fbdev: remove tmiofb driver
mmc: remove tmio_mmc driver
mfd: remove ucb1400 support
mfd: remove toshiba tmio drivers
rtc: remove v3020 driver
power: remove pda_power supply driver
ASoC: pxa: remove unused board support
pcmcia: remove unused pxa/sa1100 drivers
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 6.3-rc1
Here are the USB-serial updates for 6.3-rc1; just a new modem device
id this time.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.3-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add support for VW/Skoda "Carstick LTE"
|
|
of_gpio.h provides a single function, which is not used in this driver.
Remove unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230215165239.83806-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
28th bit of fixed supply sink PDO represents higher capability.
When this bit is set, the sink device needs more than vsafe5V
(eg: 12 V) to provide full functionality. This patch adds
this higher capability sysfs interface for sink PDO.
28th bit of fixed supply source PDO represents usb_suspend_supported
attribute. This usb_suspend_supported sysfs is already exposed for
source PDOs. This patch adds 'source-capabilities' in
usb_suspend_supported sysfs documentation for additional clarity.
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230214114543.205103-2-saranya.gopal@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As per USB PD specification, 28th bit of fixed supply sink PDO
represents "higher capability" attribute and not "usb suspend
supported" attribute. So, this patch removes the usb_suspend_supported
attribute from sink PDO.
Fixes: 662a60102c12 ("usb: typec: Separate USB Power Delivery from USB Type-C")
Cc: stable <stable@kernel.org>
Reported-by: Rajaram Regupathy <rajaram.regupathy@intel.com>
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230214114543.205103-1-saranya.gopal@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds the necessary PCI IDs for Intel Meteor Lake-M
devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230215132711.35668-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The function gether_setup_name_default() is called by various USB
ethernet gadget drivers. Calling this function will select a random
host and device MAC addresses. A properly working driver should be
silent and not warn the user about default MAC addresses selection.
Given that the MAC addresses are also printed when the function
gether_register_netdev() is called, remove these unnecessary warnings.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Link: https://lore.kernel.org/r/20230209125319.18589-2-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB ethernet gadget driver implements its own print macros which
call printk. Device drivers should use the device prints that print the
device name. Fortunately, the same macro names are defined in the header
file 'linux/usb/composite.h' and these use the device prints. Therefore,
remove the local definitions in the USB ethernet gadget driver and use
those in 'linux/usb/composite.h'. The only difference is that now the
device name is printed instead of the ethernet interface name.
Tested using ethernet gadget on Jetson AGX Orin.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230209125319.18589-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Consider a case where gserial_disconnect has already cleared
gser->ioport. And if a wakeup interrupt triggers afterwards,
gserial_resume gets called, which will lead to accessing of
gser->ioport and thus causing null pointer dereference.Add
a null pointer check to prevent this.
Added a static spinlock to prevent gser->ioport from becoming
null after the newly added check.
Fixes: aba3a8d01d62 ("usb: gadget: u_serial: add suspend resume callbacks")
Cc: stable <stable@kernel.org>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1676309438-14922-1-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If kstrtou8() fails, the mutex_unlock() is missed, move kstrtou8()
before mutex_lock() to fix it up.
Fixes: 0525210c9840 ("usb: gadget: uvc: Allow definition of XUs in configfs")
Fixes: b3c839bd8a07 ("usb: gadget: uvc: Make bSourceID read/write")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20230213070926.776447-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's possible to exit the loop with "sysdev" set to NULL. In that
case we should use "&pdev->dev".
Fixes: ec5499d338ec ("xhci: split out rcar/rz support from xhci-plat.c")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/Y+T4kTcJwRwxNHJq@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace direct modifications to vma->vm_flags with calls to modifier
functions to be able to track flag changes and to keep vma locking
correctness.
[akpm@linux-foundation.org: fix drivers/misc/open-dice.c, per Hyeonggon Yoo]
Link: https://lkml.kernel.org/r/20230126193752.297968-5-surenb@google.com
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Mike Rapoport (IBM) <rppt@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjun Roy <arjunroy@google.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: David Rientjes <rientjes@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: Laurent Dufour <ldufour@linux.ibm.com>
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Minchan Kim <minchan@google.com>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Peter Oskolkov <posk@google.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Punit Agrawal <punit.agrawal@bytedance.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The Alcor Link AK9563 smartcard reader used on some Lenovo platforms
doesn't work. If LPM is enabled the reader will provide an invalid
usb config descriptor. Added quirk to disable LPM.
Verified fix on Lenovo P16 G1 and T14 G3
Tested-by: Miroslav Zatko <mzatko@mirexoft.com>
Tested-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20230208181223.1092654-1-mpearson-lenovo@squebb.ca
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While checking Pin Assignments of the port and partner during probe, we
don't take into account whether the peripheral is a plug or receptacle.
This manifests itself in a mode entry failure on certain docks and
dongles with captive cables. For instance, the Startech.com Type-C to DP
dongle (Model #CDP2DP) advertises its DP VDO as 0x405. This would fail
the Pin Assignment compatibility check, despite it supporting
Pin Assignment C as a UFP.
Update the check to use the correct DP Pin Assign macros that
take the peripheral's receptacle bit into account.
Fixes: c1e5c2f0cb8a ("usb: typec: altmodes/displayport: correct pin assignment for UFP receptacles")
Cc: stable@vger.kernel.org
Reported-by: Diana Zigterman <dzigterman@chromium.org>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20230208205318.131385-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 321b59870f850a10dbb211ecd2bd87b41497ea6f.
This commit broke USB networking on Ingenic SoCs and maybe elsewhere.
The actual reason is unknown; and while a proper fix would be better,
we're sitting at -rc7 now, so a revert is justified - and we can work on
re-introducing this change for 6.3.
Fixes: 321b59870f85 ("usb: gadget: u_ether: Do not make UDC parent of the net device")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20230209105626.10597-1-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This sets both of_node fields and takes a of_node reference as well.
Fixes: bb160ee61c04 ("drivers/usb/host/ehci-fsl: Fix interrupt setup in host mode.")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230207110531.1060252-4-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix a -Wunused-but-set-variable warning in gadget_string_s_store()
Fixes: 15a7cf8caabe ("usb: gadget: configfs: Support arbitrary string descriptors")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230209094359.1549629-1-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the user has defined a custom string descriptor for the IAD or the
VideoStreaming interfaces then set their index field to point to the
custom descriptor instead of the hardcoded defaults. If no custom
descriptors have been linked to, then use the default ones.
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230206161802.892954-12-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently the string descriptors for the IAD and VideoStreaming
Interfaces are hardcoded into f_uvc. Now that we can create arbitrary
string descriptors, add a mechanism to define string descriptors for
the IAD, VC and VS interfaces by linking to the appropriate directory
at function level.
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230206161802.892954-11-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If any custom string descriptors have been linked to from the
extension unit, pick up the string ID that was returned when
the strings were attached to the composite dev and use it to
set the iExtension field of the Extension Unit Descriptor.
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230206161802.892954-10-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add .allow_link() and .drop_link() callbacks to allow users to link
an extension unit descriptor to a string descriptor.
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230206161802.892954-9-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Attach any arbitrary strings that are defined to the composite dev.
We handle the old-style manufacturer, product and serialnumbers
strings in the same function for simplicity.
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230206161802.892954-8-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a framework to allow users to define arbitrary string descriptors
for a USB Gadget. This is modelled as a new type of config item rather
than as hardcoded attributes so as to be as flexible as possible.
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230206161802.892954-7-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The struct gadget_strings really represents a single language in
configfs. Rename it to make that more clear.
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230206161802.892954-6-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that extension unit support is available through configfs we need
to copy the descriptors for the XUs during uvc_function_bind() so that
they're exposed to the usb subsystem.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230206161802.892954-5-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
