Age | Commit message (Collapse) | Author | Files | Lines |
|
commit 6d33377f2abbf9f0e561b116dd468d1c3ff36a6a upstream.
Signed-off-by: Laurent Caumont <lcaumont2@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 29a90b70893817e2f2bb3cea40a29f5308e21b21 upstream.
The intel-iommu DMA ops fail to correctly handle scatterlists where
sg->offset is greater than PAGE_SIZE - the IOVA allocation is computed
appropriately based on the page-aligned portion of the offset, but the
mapping is set up relative to sg->page, which means it fails to actually
cover the whole buffer (and in the worst case doesn't cover it at all):
(sg->dma_address + sg->dma_len) ----+
sg->dma_address ---------+ |
iov_pfn------+ | |
| | |
v v v
iova: a b c d e f
|--------|--------|--------|--------|--------|
<...calculated....>
[_____mapped______]
pfn: 0 1 2 3 4 5
|--------|--------|--------|--------|--------|
^ ^ ^
| | |
sg->page ----+ | |
sg->offset --------------+ |
(sg->offset + sg->length) ----------+
As a result, the caller ends up overrunning the mapping into whatever
lies beyond, which usually goes badly:
[ 429.645492] DMAR: DRHD: handling fault status reg 2
[ 429.650847] DMAR: [DMA Write] Request device [02:00.4] fault addr f2682000 ...
Whilst this is a fairly rare occurrence, it can happen from the result
of intermediate scatterlist processing such as scatterwalk_ffwd() in the
crypto layer. Whilst that particular site could be fixed up, it still
seems worthwhile to bring intel-iommu in line with other DMA API
implementations in handling this robustly.
To that end, fix the intel_map_sg() path to line up the mapping
correctly (in units of MM pages rather than VT-d pages to match the
aligned_nrpages() calculation) regardless of the offset, and use
sg_phys() consistently for clarity.
Reported-by: Harsh Jain <Harsh@chelsio.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed by: Ashok Raj <ashok.raj@intel.com>
Tested by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit af97a77bc01ce49a466f9d4c0125479e2e2230b6 upstream.
Thanks to the scripts/leaking_addresses.pl script, it was found that
some EFI values should not be readable by non-root users.
So make them root-only, and to do that, add a __ATTR_RO_MODE() macro to
make this easier, and use it in other places at the same time.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20171206095010.24170-2-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5a244727f428a06634f22bb890e78024ab0c89f3 upstream.
The isa_driver structure for an isa_bus device is stored in the device
platform_data member of the respective device structure. This
platform_data member may be reset to NULL if isa_driver match callback
for the device fails, indicating a device unsupported by the ISA driver.
This patch fixes a possible NULL pointer dereference if one of the
isa_driver callbacks to attempted for an unsupported device. This error
should not occur in practice since ISA devices are typically manually
configured and loaded by the users, but we may as well prevent this
error from popping up for the 0day testers.
Fixes: a5117ba7da37 ("[PATCH] Driver model: add ISA bus")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e60ea67bb60459b95a50a156296041a13e0e380e upstream.
index can be reused by other virtio device.
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 12147edc434c9e4c7c2f5fee2e5519b2e5ac34ce upstream.
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7a31ced3de06e9878e4f9c3abe8f87d9344d8144 upstream.
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bd352e1adfe0d02d3ea7c8e3fb19183dc317e679 upstream.
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6aa8d5945502baf4687d80de59b7ac865e9e666b upstream.
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8bd13bd522ff7dfa0eb371921aeb417155f7a3be upstream.
Avoid flooding the kernel log with "Formate error", if incomplete message
are received.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e84f44eb5523401faeb9cc1c97895b68e3cfb78d upstream.
The conditon in the while-loop becomes true when actual_length is less than
2 (MSG_HEADER_LEN). In best case we end up with a former, already
dispatched msg, that got msg->len greater than actual_length. This will
result in a "Format error" error printout.
Problem seen when unplugging a Kvaser USB device connected to a vbox guest.
warning: comparison between signed and unsigned integer expressions
[-Wsign-compare]
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 435019b48033138581a6171093b181fc6b4d3d30 upstream.
The allocated buffer was not freed if usb_submit_urb() failed.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d5a31582ef046d3b233f0da1a68ae26519b2f0a upstream.
The variable temp is incorrectly being updated, instead it should
be offset otherwise the loop just reads the same capability value
and loops forever. Thanks to Alan Stern for pointing out the
correct fix to my original fix. Fix also cleans up clang warning:
drivers/usb/host/ehci-dbg.c:840:4: warning: Value stored to 'temp'
is never read
Fixes: d49d43174400 ("USB: misc ehci updates")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 446f666da9f019ce2ffd03800995487e79a91462 upstream.
USBDEVFS_URB_ISO_ASAP must be accepted only for ISO endpoints.
Improve sanity checking.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 57999d1107c1e60c2ca7088f2ac0f819e2f554b3 upstream.
There used to be an integer overflow check in proc_do_submiturb() but
we removed it. It turns out that it's still required. The
uurb->buffer_length variable is a signed integer and it's controlled by
the user. It can lead to an integer overflow when we do:
num_sgs = DIV_ROUND_UP(uurb->buffer_length, USB_SG_SIZE);
If we strip away the macro then that line looks like this:
num_sgs = (uurb->buffer_length + USB_SG_SIZE - 1) / USB_SG_SIZE;
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
It's the first addition which can overflow.
Fixes: 1129d270cbfb ("USB: Increase usbfs transfer limit")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1129d270cbfbb7e2b1ec3dede4a13930bdd10e41 upstream.
Promote a variable keeping track of USB transfer memory usage to a
wider data type and allow for higher bandwidth transfers from a large
number of USB devices connected to a single host.
Signed-off-by: Mateusz Berezecki <mateuszb@fastmail.fm>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 973593a960ddac0f14f0d8877d2d0abe0afda795 upstream.
Sometimes the USB device gets confused about the state of the initialization and
the connection fails. In particular, the device thinks that it's already set up
and running while the host thinks the device still needs to be configured. To
work around this issue, power-cycle the hub's output to issue a sort of "reset"
to the device. This makes the device restart its state machine and then the
initialization succeeds.
This fixes problems where the kernel reports a list of errors like this:
usb 1-1.3: device not accepting address 19, error -71
The end result is a non-functioning device. After this patch, the sequence
becomes like this:
usb 1-1.3: new high-speed USB device number 18 using ci_hdrc
usb 1-1.3: device not accepting address 18, error -71
usb 1-1.3: new high-speed USB device number 19 using ci_hdrc
usb 1-1.3: device not accepting address 19, error -71
usb 1-1-port3: attempt power cycle
usb 1-1.3: new high-speed USB device number 21 using ci_hdrc
usb-storage 1-1.3:1.2: USB Mass Storage device detected
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3bfd1300abfe3adb18e84a89d97a0e82a22124bb upstream.
This device will be used in future Amazon EC2 instances as the primary
serial port (i.e., data sent to this port will be available via the
GetConsoleOuput [1] EC2 API).
[1] http://docs.aws.amazon.com/AWSEC2/latest/APIReference/API_GetConsoleOutput.html
Signed-off-by: Matt Wilson <msw@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e43a12f1793ae1fe006e26fe9327a8840a92233c upstream.
KY-688 USB 3.1 Type-C Hub internally uses a Genesys Logic hub to connect
to Realtek r8153.
Similar to commit ("7496cfe5431f2 usb: quirks: Add no-lpm quirk for Moshi
USB to Ethernet Adapter"), no-lpm can make r8153 ethernet work.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7fee72d5e8f1e7b8d8212e28291b1a0243ecf2f1 upstream.
We've been adding this as a quirk on a per device basis hoping that
newer disk enclosures would do better, but that has not happened,
so simply apply this quirk to all Seagate devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 01f8902bcf3ff124d0aeb88a774180ebcec20ace ]
Fix hardware setup of multicast address hash:
- Never clear the hardware hash (to avoid packet loss)
- Construct the hash register values in software and then write once
to hardware
Signed-off-by: Rui Sousa <rui.sousa@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0911d0041c22922228ca52a977d7b0b0159fee4b ]
Some ->page_mkwrite handlers may return VM_FAULT_RETRY as its return
code (GFS2 or Lustre can definitely do this). However VM_FAULT_RETRY
from ->page_mkwrite is completely unhandled by the mm code and results
in locking and writeably mapping the page which definitely is not what
the caller wanted.
Fix Lustre and block_page_mkwrite_ret() used by other filesystems
(notably GFS2) to return VM_FAULT_NOPAGE instead which results in
bailing out from the fault code, the CPU then retries the access, and we
fault again effectively doing what the handler wanted.
Link: http://lkml.kernel.org/r/20170203150729.15863-1-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ce7e40c432ba84da104438f6799d460a4cad41bc ]
ipddp_route structs contain alignment padding so kernel heap memory
is leaked when they are copied to user space in
ipddp_ioctl(SIOCFINDIPDDPRT). Change kmalloc() to kzalloc() to clear
that memory.
Signed-off-by: Vlad Tsyrklevich <vlad@tsyrklevich.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b00bebbc301c8e1f74f230dc82282e56b7e7a6db ]
When kernel configuration SMP,PREEMPT and DEBUG_PREEMPT are enabled,
echo 1 >/proc/sys/kernel/sysrq
echo p >/proc/sysrq-trigger
kernel will print call trace as below:
sysrq: SysRq : Show Regs
BUG: using __this_cpu_read() in preemptible [00000000] code: sh/435
caller is __this_cpu_preempt_check+0x18/0x20
Call trace:
[<ffffff8008088e80>] dump_backtrace+0x0/0x1d0
[<ffffff8008089074>] show_stack+0x24/0x30
[<ffffff8008447970>] dump_stack+0x90/0xb0
[<ffffff8008463950>] check_preemption_disabled+0x100/0x108
[<ffffff8008463998>] __this_cpu_preempt_check+0x18/0x20
[<ffffff80084c9194>] sysrq_handle_showregs+0x1c/0x40
[<ffffff80084c9c7c>] __handle_sysrq+0x12c/0x1a0
[<ffffff80084ca140>] write_sysrq_trigger+0x60/0x70
[<ffffff8008251e00>] proc_reg_write+0x90/0xd0
[<ffffff80081f1788>] __vfs_write+0x48/0x90
[<ffffff80081f241c>] vfs_write+0xa4/0x190
[<ffffff80081f3354>] SyS_write+0x54/0xb0
[<ffffff80080833f0>] el0_svc_naked+0x24/0x28
This can be seen on a common board like an r-pi3.
This happens because when echo p >/proc/sysrq-trigger,
get_irq_regs() is called outside of IRQ context,
if preemption is enabled in this situation,kernel will
print the call trace. Since many prior discussions on
the mailing lists have made it clear that get_irq_regs
either just returns NULL or stale data when used outside
of IRQ context,we simply avoid calling it outside of
IRQ context.
Signed-off-by: Jibin Xu <jibin.xu@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a8e9b186f153a44690ad0363a56716e7077ad28c ]
Add missing break statement in order to prevent the code from falling
through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20171016174029.GA19757@embeddedor.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 36735783fdb599c94b9c86824583df367c65900b ]
DMA supports 32-bit words only,
even if BITLEN1 of SITMDR2 register is 16bit.
Fixes: b0d0ce8b6b91 ("spi: sh-msiof: Add DMA support")
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3236a965486ba0c6043cf2c7b51943d8b382ae29 ]
This driver's ->rs485_config callback checks if SER_RS485_RTS_ON_SEND
and SER_RS485_RTS_AFTER_SEND have the same value. If they do, it means
the user has passed in invalid data with the TIOCSRS485 ioctl()
since RTS must have a different polarity when sending and when not
sending. In this case, rs485 mode is not enabled (the RS485_URA bit
is not set in the RS485 Enable Register) and this is supposed to be
signaled back to the user by clearing the SER_RS485_ENABLED bit in
struct serial_rs485 ... except a missing tilde character is preventing
that from happening.
Fixes: 28e3fb6c4dce ("serial: Add support for Fintek F81216A LPC to 4 UART")
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e393aa2446150536929140739f09c6ecbcbea7f0 upstream.
When we send a read request and hit the clean data in cache device, there
is a situation called cache read race in bcache(see the commit in the tail
of cache_look_up(), the following explaination just copy from there):
The bucket we're reading from might be reused while our bio is in flight,
and we could then end up reading the wrong data. We guard against this
by checking (in bch_cache_read_endio()) if the pointer is stale again;
if so, we treat it as an error (s->iop.error = -EINTR) and reread from
the backing device (but we don't pass that error up anywhere)
It should be noted that cache read race happened under normal
circumstances, not the circumstance when SSD failed, it was counted
and shown in /sys/fs/bcache/XXX/internal/cache_read_races.
Without this patch, when we use writeback mode, we will never reread from
the backing device when cache read race happened, until the whole cache
device is clean, because the condition
(s->recoverable && (dc && !atomic_read(&dc->has_dirty))) is false in
cached_dev_read_error(). In this situation, the s->iop.error(= -EINTR)
will be passed up, at last, user will receive -EINTR when it's bio end,
this is not suitable, and wield to up-application.
In this patch, we use s->read_dirty_data to judge whether the read
request hit dirty data in cache device, it is safe to reread data from
the backing device when the read request hit clean data. This can not
only handle cache read race, but also recover data when failed read
request from cache device.
[edited by mlyle to fix up whitespace, commit log title, comment
spelling]
Fixes: d59b23795933 ("bcache: only permit to recovery read error when cache device is clean")
Signed-off-by: Hua Rui <huarui.dev@gmail.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d59b23795933678c9638fd20c942d2b4f3cd6185 upstream.
When bcache does read I/Os, for example in writeback or writethrough mode,
if a read request on cache device is failed, bcache will try to recovery
the request by reading from cached device. If the data on cached device is
not synced with cache device, then requester will get a stale data.
For critical storage system like database, providing stale data from
recovery may result an application level data corruption, which is
unacceptible.
With this patch, for a failed read request in writeback or writethrough
mode, recovery a recoverable read request only happens when cache device
is clean. That is to say, all data on cached device is up to update.
For other cache modes in bcache, read request will never hit
cached_dev_read_error(), they don't need this patch.
Please note, because cache mode can be switched arbitrarily in run time, a
writethrough mode might be switched from a writeback mode. Therefore
checking dc->has_data in writethrough mode still makes sense.
Changelog:
V4: Fix parens error pointed by Michael Lyle.
v3: By response from Kent Oversteet, he thinks recovering stale data is a
bug to fix, and option to permit it is unnecessary. So this version
the sysfs file is removed.
v2: rename sysfs entry from allow_stale_data_on_failure to
allow_stale_data_on_failure, and fix the confusing commit log.
v1: initial patch posted.
[small change to patch comment spelling by mlyle]
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reported-by: Arne Wolf <awolf@lenovo.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Nix <nix@esperi.org.uk>
Cc: Kai Krakow <hurikhan77@gmail.com>
Cc: Eric Wheeler <bcache@lists.ewheeler.net>
Cc: Junhui Tang <tang.junhui@zte.com.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 56350fb8978bbf4aafe08f21234e161dd128b417 upstream.
The hardware always writes one or two bytes in the index portion of
an indexed transfer. Make sure the message we send as the index
doesn't have a zero length.
Cc: Daniel Kurtz <djkurtz@chromium.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <seanpaul@chromium.org>
Fixes: 56f9eac05489 ("drm/i915/intel_i2c: use INDEX cycles for i2c read transactions")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123194157.25367-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit bb9e0d4bca50f429152e74a459160b41f3d60fb2)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ae5c631e605a452a5a0e73205a92810c01ed954b upstream.
We can only specify the one slave address to indexed reads/writes.
Make sure the messages we check are destined to the same slave
address before deciding to do an indexed transfer.
Cc: Daniel Kurtz <djkurtz@chromium.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <seanpaul@chromium.org>
Fixes: 56f9eac05489 ("drm/i915/intel_i2c: use INDEX cycles for i2c read transactions")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123194157.25367-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit c4deb62d7821672265b87952bcd1c808f3bf3e8f)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f3621a8eb59a913612c8e6e37d81f16b649f8b6c upstream.
During panel removal or system shutdown panel_simple_disable() is called
which disables the panel backlight but the panel is still powered due to
missing calls to panel_simple_unprepare().
Fixes: d02fd93e2cd8 ("drm/panel: simple - Disable panel on shutdown")
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170807115545.27747-1-net147@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d9bcd462daf34aebb8de9ad7f76de0198bb5a0f0 upstream.
So far we completely rely on the caller to provide valid arguments.
To be on the safe side perform an own sanity check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 639b08810d6ad74ded2c5f6e233c4fcb9d147168 ]
When accessing Xenstore in a transaction the user is specifying a
transaction id which he normally obtained from Xenstore when starting
the transaction. Xenstore is validating a transaction id against all
known transaction ids of the connection the request came in. As all
requests of a domain not being the one where Xenstore lives share
one connection, validation of transaction ids of different users of
Xenstore in that domain should be done by the kernel of that domain
being the multiplexer between the Xenstore users in that domain and
Xenstore.
In order to prohibit one Xenstore user "hijacking" a transaction from
another user the xenbus driver has to verify a given transaction id
against all known transaction ids of the user before forwarding it to
Xenstore.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 91ca1a8c584f55857b1f6ab20a1d3a1ce7a559bb ]
At the end of function ad7150_write_event_config(), directly returns 0.
As a result, the errors will be ignored by the callers. It may be better
to return variable "ret".
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7357f89954b6d005df6ab8929759e78d7d9a80f9 ]
I reported the include issue for tracepoints a while ago, but nothing
seems to have happened. Now it bit us, since the drm_mm_print
conversion was broken for armada. Fix it, so I can re-enable armada
in the drm-misc build configs.
v2: Rebase just the compile fix on top of Chris' build fix.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1483115932-19584-1-git-send-email-daniel.vetter@ffwll.ch
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 107fded7bf616ad6f46823d98b8ed6405d7adf2d ]
In a few cases the err-variable is not set to a negative error code if a
function call in typhoon_init_one() fails and thus 0 is returned
instead.
It may be better to set err to the appropriate negative error
code before returning.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188841
Reported-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Thomas Preisner <thomas.preisner+linux@fau.de>
Signed-off-by: Milan Stephan <milan.stephan+linux@fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6b6bbb5922a4b1d4b58125a572da91010295fba3 ]
In some cases the return value of a failing function is not being used
and the function typhoon_init_one() returns another negative error code
instead.
Signed-off-by: Thomas Preisner <thomas.preisner+linux@fau.de>
Signed-off-by: Milan Stephan <milan.stephan+linux@fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 977509f7c5c6fb992ffcdf4291051af343b91645 ]
Previously we didn't check the type of device before trying to apply Type 1
(PCI-X) or Type 2 (PCIe) Setting Records from _HPX.
We don't support PCI-X Setting Records, so this was harmless, but the
warning was useless.
We do support PCIe Setting Records, and we didn't check whether a device
was PCIe before applying settings. I don't think anything bad happened on
non-PCIe devices because pcie_capability_clear_and_set_word(),
pcie_cap_has_lnkctl(), etc., would fail before doing any harm. But it's
ugly to depend on those internals.
Check the device type before attempting to apply Type 1 and Type 2 Setting
Records (Type 0 records are applicable to PCI, PCI-X, and PCIe devices).
A side benefit is that this prevents useless "not supported" warnings when
a BIOS supplies a Type 1 (PCI-X) Setting Record and we try to apply it to
every single device:
pci 0000:00:00.0: PCI-X settings not supported
After this patch, we'll get the warning only when a BIOS supplies a Type 1
record and we have a PCI-X device to which it should be applied.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=187731
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 19110cfbb34d4af0cdfe14cd243f3b09dc95b013 upstream.
Lennart reported the following race condition:
\ e1000_watchdog_task
\ e1000e_has_link
\ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link
/* link is up */
mac->get_link_status = false;
/* interrupt */
\ e1000_msix_other
hw->mac.get_link_status = true;
link_active = !hw->mac.get_link_status
/* link_active is false, wrongly */
This problem arises because the single flag get_link_status is used to
signal two different states: link status needs checking and link status is
down.
Avoid the problem by using the return value of .check_for_link to signal
the link status to e1000e_has_link().
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3509f8bc7b0560044c15f0e3ecfde1d9af757a6 upstream.
All the helpers return -E1000_ERR_PHY.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c4c40e51f9c32c6dd8adf606624c930a1c4d9bbb upstream.
In case of error from e1e_rphy(), the loop will exit early and "success"
will be set to true erroneously.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is based on upstream commit 10e840dfb0b7, which did not touch the
iio-trig-periodic-rtc driver because it has been removed upstream.
The following explanation comes from that commit:
These stand-alone trigger drivers were using iio_trigger_put()
where they should have been using iio_trigger_free(). The
iio_trigger_put() adds a module_put which is bad since they
never did a module_get.
In the sysfs driver, module_get/put's are used as triggers are
added & removed. This extra module_put() occurs on an error path
in the probe routine (probably rare).
In the bfin-timer & interrupt trigger drivers, the module resources
are not explicitly managed, so it's doing a put on something that
was never get'd. It occurs on the probe error path and on the
remove path (not so rare).
Tested with the sysfs trigger driver.
The bfin & interrupt drivers were build tested & inspected only.
This was build tested only.
Cc: Alison Schofield <amsfield22@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Parsing CDC headers a buffer overflow cannot just be prevented
by checking that the remainder of the buffer is longer than minimum
length. The size of the fields to be parsed must be figured in, too.
In newer kernels this issue has been fixed at a central location with
commit 2e1c42391ff2556387b3cb6308b24f6f65619feb
Author: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Date: Thu Sep 21 16:58:48 2017 +0200
USB: core: harden cdc_parse_cdc_header
on anything older the parsing had not been centralised, so a separate
fix for each driver is necessary.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 30863e38ebeb500a31cecee8096fb5002677dd9b upstream.
When mtdoops calls mtd_panic_write(), it eventually calls
panic_nand_write() in nand_base.c. In order to properly wait for the
nand chip to be ready in panic_nand_wait(), the chip must first be
selected.
When using the atmel nand flash controller, a panic would occur due to
a NULL pointer exception.
Fixes: 2af7c6539931 ("mtd: Add panic_write for NAND flashes")
Signed-off-by: Brent Taylor <motobud@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9cac9d2fb2fe0e0cadacdb94415b3fe49e3f724f upstream.
VIDIOC_DQEVENT and VIDIOC_QUERY_EXT_CTRL should give the same output for
the control flags field.
This patch creates a new function user_flags(), that calculates the user
exported flags value (which is different than the kernel internal flags
structure). This function is then used by all the code that exports the
internal flags to userspace.
Reported-by: Dimitrios Katsaros <patcherwork@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3e45067f94bbd61dec0619b1c32744eb0de480c8 upstream.
The ioctl LIRC_SET_REC_TIMEOUT would set a timeout of 704ns if called
with a timeout of 4294968us.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b3120d2cc447ee77b9d69bf4ad7b452c9adb4d39 upstream.
Firmware load on AS102 is using the stack which is not allowed any
longer. We currently fail with:
kernel: transfer buffer not dma capable
kernel: ------------[ cut here ]------------
kernel: WARNING: CPU: 0 PID: 598 at drivers/usb/core/hcd.c:1595 usb_hcd_map_urb_for_dma+0x41d/0x620
kernel: Modules linked in: amd64_edac_mod(-) edac_mce_amd as102_fe dvb_as102(+) kvm_amd kvm snd_hda_codec_realtek dvb_core snd_hda_codec_generic snd_hda_codec_hdmi snd_hda_intel snd_hda_codec irqbypass crct10dif_pclmul crc32_pclmul snd_hda_core snd_hwdep snd_seq ghash_clmulni_intel sp5100_tco fam15h_power wmi k10temp i2c_piix4 snd_seq_device snd_pcm snd_timer parport_pc parport tpm_infineon snd tpm_tis soundcore tpm_tis_core tpm shpchp acpi_cpufreq xfs libcrc32c amdgpu amdkfd amd_iommu_v2 radeon hid_logitech_hidpp i2c_algo_bit drm_kms_helper crc32c_intel ttm drm r8169 mii hid_logitech_dj
kernel: CPU: 0 PID: 598 Comm: systemd-udevd Not tainted 4.13.10-200.fc26.x86_64 #1
kernel: Hardware name: ASUS All Series/AM1I-A, BIOS 0505 03/13/2014
kernel: task: ffff979933b24c80 task.stack: ffffaf83413a4000
kernel: RIP: 0010:usb_hcd_map_urb_for_dma+0x41d/0x620
systemd-fsck[659]: /dev/sda2: clean, 49/128016 files, 268609/512000 blocks
kernel: RSP: 0018:ffffaf83413a7728 EFLAGS: 00010282
systemd-udevd[604]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
kernel: RAX: 000000000000001f RBX: ffff979930bce780 RCX: 0000000000000000
kernel: RDX: 0000000000000000 RSI: ffff97993ec0e118 RDI: ffff97993ec0e118
kernel: RBP: ffffaf83413a7768 R08: 000000000000039a R09: 0000000000000000
kernel: R10: 0000000000000001 R11: 00000000ffffffff R12: 00000000fffffff5
kernel: R13: 0000000001400000 R14: 0000000000000001 R15: ffff979930806800
kernel: FS: 00007effaca5c8c0(0000) GS:ffff97993ec00000(0000) knlGS:0000000000000000
kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
kernel: CR2: 00007effa9fca962 CR3: 0000000233089000 CR4: 00000000000406f0
kernel: Call Trace:
kernel: usb_hcd_submit_urb+0x493/0xb40
kernel: ? page_cache_tree_insert+0x100/0x100
kernel: ? xfs_iunlock+0xd5/0x100 [xfs]
kernel: ? xfs_file_buffered_aio_read+0x57/0xc0 [xfs]
kernel: usb_submit_urb+0x22d/0x560
kernel: usb_start_wait_urb+0x6e/0x180
kernel: usb_bulk_msg+0xb8/0x160
kernel: as102_send_ep1+0x49/0xe0 [dvb_as102]
kernel: ? devres_add+0x3f/0x50
kernel: as102_firmware_upload.isra.0+0x1dc/0x210 [dvb_as102]
kernel: as102_fw_upload+0xb6/0x1f0 [dvb_as102]
kernel: as102_dvb_register+0x2af/0x2d0 [dvb_as102]
kernel: as102_usb_probe+0x1f3/0x260 [dvb_as102]
kernel: usb_probe_interface+0x124/0x300
kernel: driver_probe_device+0x2ff/0x450
kernel: __driver_attach+0xa4/0xe0
kernel: ? driver_probe_device+0x450/0x450
kernel: bus_for_each_dev+0x6e/0xb0
kernel: driver_attach+0x1e/0x20
kernel: bus_add_driver+0x1c7/0x270
kernel: driver_register+0x60/0xe0
kernel: usb_register_driver+0x81/0x150
kernel: ? 0xffffffffc0807000
kernel: as102_usb_driver_init+0x1e/0x1000 [dvb_as102]
kernel: do_one_initcall+0x50/0x190
kernel: ? __vunmap+0x81/0xb0
kernel: ? kfree+0x154/0x170
kernel: ? kmem_cache_alloc_trace+0x15f/0x1c0
kernel: ? do_init_module+0x27/0x1e9
kernel: do_init_module+0x5f/0x1e9
kernel: load_module+0x2602/0x2c30
kernel: SYSC_init_module+0x170/0x1a0
kernel: ? SYSC_init_module+0x170/0x1a0
kernel: SyS_init_module+0xe/0x10
kernel: do_syscall_64+0x67/0x140
kernel: entry_SYSCALL64_slow_path+0x25/0x25
kernel: RIP: 0033:0x7effab6cf3ea
kernel: RSP: 002b:00007fff5cfcbbc8 EFLAGS: 00000246 ORIG_RAX: 00000000000000af
kernel: RAX: ffffffffffffffda RBX: 00005569e0b83760 RCX: 00007effab6cf3ea
kernel: RDX: 00007effac2099c5 RSI: 0000000000009a13 RDI: 00005569e0b98c50
kernel: RBP: 00007effac2099c5 R08: 00005569e0b83ed0 R09: 0000000000001d80
kernel: R10: 00007effab98db00 R11: 0000000000000246 R12: 00005569e0b98c50
kernel: R13: 00005569e0b81c60 R14: 0000000000020000 R15: 00005569dfadfdf7
kernel: Code: 48 39 c8 73 30 80 3d 59 60 9d 00 00 41 bc f5 ff ff ff 0f 85 26 ff ff ff 48 c7 c7 b8 6b d0 92 c6 05 3f 60 9d 00 01 e8 24 3d ad ff <0f> ff 8b 53 64 e9 09 ff ff ff 65 48 8b 0c 25 00 d3 00 00 48 8b
kernel: ---[ end trace c4cae366180e70ec ]---
kernel: as10x_usb: error during firmware upload part1
Let's allocate the the structure dynamically so we can get the firmware
loaded correctly:
[ 14.243057] as10x_usb: firmware: as102_data1_st.hex loaded with success
[ 14.500777] as10x_usb: firmware: as102_data2_st.hex loaded with success
Signed-off-by: Michele Baldessari <michele@acksyn.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0a9a17e3bb4564caf4bfe2a6783ae1287667d188 upstream.
This patch fixes an issue seen on Power systems with ixgbe which results
in skb list corruption and an eventual kernel oops. The following is what
was observed:
CPU 1 CPU2
============================ ============================
1: ixgbe_xmit_frame_ring ixgbe_clean_tx_irq
2: first->skb = skb eop_desc = tx_buffer->next_to_watch
3: ixgbe_tx_map read_barrier_depends()
4: wmb check adapter written status bit
5: first->next_to_watch = tx_desc napi_consume_skb(tx_buffer->skb ..);
6: writel(i, tx_ring->tail);
The read_barrier_depends is insufficient to ensure that tx_buffer->skb does not
get loaded prior to tx_buffer->next_to_watch, which then results in loading
a stale skb pointer. This patch replaces the read_barrier_depends with
smp_rmb to ensure loads are ordered with respect to the load of
tx_buffer->next_to_watch.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b8edcc685b5e2c3c37aa13dc50a88e84a5bfef8 upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with fm10k as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|