Age | Commit message (Collapse) | Author | Files | Lines |
|
As the i.MX8MP supports reading MAC propagation delay and correcting the
Hardware timestamp counter for additional delays [1], enable the feature
for this SoC.
This reduces phase error of the PPS output from the PTP Hardware Clock
from approx 150ns to 100ns.
[1] i.MX8MP Reference Manual, rev.1 Section 11.7.2.5.3 "Timestamp
correction"
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Link: https://lore.kernel.org/r/20230719-stmmac_correct_mac_delay-v3-2-61e63427735e@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The IEEE1588 Standard specifies that the timestamps of Packets must be
captured when the PTP message timestamp point (leading edge of first
octet after the start of frame delimiter) crosses the boundary between
the node and the network. As the MAC latches the timestamp at an
internal point, the captured timestamp must be corrected for the
additional data transmission latency, as described in the publicly
available datasheet [1].
This patch only corrects for the MAC-Internal delay, which can be read
out from the MAC_Ingress_Timestamp_Latency register on DWMAC version 5,
since the Phy framework currently does not support querying the Phy
ingress and egress latency. The Closs Domain Crossing Circuits errors as
indicated in [1] are already being accounted in the
stmmac_get_tx_hwtstamp() function and are not corrected here.
As the Latency varies for different link speeds and MII
modes of operation, the correction value needs to be updated on each
link state change.
As the delay also causes a phase shift in the timestamp counter compared
to the rest of the network, this correction will also reduce phase error
when generating PPS outputs from the timestamp counter.
Since the correction registers may be unavailable on some hardware and
no feature bits are documented for dynamically detection of the MAC
propagation delay readout, introduce a feature bit to explicitely enable
MAC delay Correction in the gluecode driver.
[1] i.MX8MP Reference Manual, rev.1 Section 11.7.2.5.3 "Timestamp
correction"
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Link: https://lore.kernel.org/r/20230719-stmmac_correct_mac_delay-v2-1-3366f38ee9a6@pengutronix.de
Link: https://lore.kernel.org/r/20230719-stmmac_correct_mac_delay-v3-1-61e63427735e@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages")
declared but never implemented it.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
address
Use eth_broadcast_addr() to assign broadcast address instead
of memset().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc with W=1 reports
drivers/net/ethernet/ibm/ibmvnic.c:194:13: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
^
This variable is not used so remove it.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202308040609.zQsSXWXI-lkp@intel.com/
Signed-off-by: Yu Liao <liaoyu15@huawei.com>
Reviewed-by: Nick Child <nnac123@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add page pool for RX buffers for faster buffer cycle and reduce CPU
usage.
The standard page pool API is used.
With iperf and 128 threads test, this patch improved the throughput
by 12-15%, and decreased the IRQ associated CPU's usage from 99-100% to
10-50%.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RX path allocates the QPL page pool at queue creation, and
tries to reuse these pages through page recycling. This patch
ensures that on refill no non-QPL pages are posted to the device.
When the driver is running low on free buffers, an ondemand
allocation step kicks in that allocates a non-qpl page for
SKB business to free up the QPL page in use.
gve_try_recycle_buf was moved to gve_rx_append_frags so that driver does
not attempt to mark buffer as used if a non-qpl page was allocated
ondemand.
Signed-off-by: Rushil Gupta <rushilg@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Bailey Forrest <bcf@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each QPL page is divided into GVE_TX_BUFS_PER_PAGE_DQO buffers.
When a packet needs to be transmitted, we break the packet into max
GVE_TX_BUF_SIZE_DQO sized chunks and transmit each chunk using a TX
descriptor.
We allocate the TX buffers from the free list in dqo_tx.
We store these TX buffer indices in an array in the pending_packet
structure.
The TX buffers are returned to the free list in dqo_compl after
receiving packet completion or when removing packets from miss
completions list.
Signed-off-by: Rushil Gupta <rushilg@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Bailey Forrest <bcf@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GVE supports QPL ("queue-page-list") mode where
all data is communicated through a set of pre-registered
pages. Adding this mode to DQO descriptor format.
Add checks, abi-changes and device options to support
QPL mode for DQO in addition to GQI. Also, use
pages-per-qpl supplied by device-option to control the
size of the "queue-page-list".
Signed-off-by: Rushil Gupta <rushilg@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Bailey Forrest <bcf@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.6
The first pull request for v6.6 and only driver patches this time.
Nothing special really standing out, it has been quiet most likely due
to vacations.
Major changes:
rtl8xxxu
- enable AP mode for: RTL8192FU, RTL8710BU (RTL8188GU),
RTL8192EU and RTL8723BU
mwifiex
- allow moving to a different namespace
mt76
- preparation for mt7925 support
- mt7981 support
ath12k
- Extremely High Throughput (EHT) PHY support for Wi-Fi 7
* tag 'wireless-next-2023-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (172 commits)
wifi: rtw89: return failure if needed firmware elements are not recognized
wifi: rtw89: add to parse firmware elements of BB and RF tables
wifi: rtw89: introduce infrastructure of firmware elements
wifi: rtw89: add firmware suit for BB MCU 0/1
wifi: rtw89: add firmware parser for v1 format
wifi: rtw89: introduce v1 format of firmware header
wifi: rtw89: support firmware log with formatted text
wifi: rtw89: recognize log format from firmware file
wifi: ath12k: avoid deadlock by change ieee80211_queue_work for regd_update_work
wifi: ath12k: add handler for scan event WMI_SCAN_EVENT_DEQUEUED
wifi: ath12k: relax list iteration in ath12k_mac_vif_unref()
wifi: ath12k: configure puncturing bitmap
wifi: ath12k: parse WMI service ready ext2 event
wifi: ath12k: add MLO header in peer association
wifi: ath12k: peer assoc for 320 MHz
wifi: ath12k: add WMI support for EHT peer
wifi: ath12k: prepare EHT peer assoc parameters
wifi: ath12k: add EHT PHY modes
wifi: ath12k: propagate EHT capabilities to userspace
wifi: ath12k: WMI support to process EHT capabilities
...
====================
Link: https://lore.kernel.org/r/87msz7j942.fsf@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move marking the PHY as being on a SFP module into the SFP code between
getting the PHY device (and thus initialising the phy_device structure)
and registering the discovered device.
This means that PHY drivers can use phy_on_sfp() in their match and
get_features methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qRaga-001vKt-8X@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit c3d2ed93b14d ("mlxsw: Remove old parsing depth infrastructure")
left behind mlxsw_sp_nve_inc_parsing_depth_get()/mlxsw_sp_nve_inc_parsing_depth_put().
And commit 532b49e41e64 ("mlxsw: spectrum_span: Derive SBIB from maximum port speed & MTU")
remove mlxsw_sp_span_port_mtu_update()/mlxsw_sp_span_speed_update_work() but leave the
declarations.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20230803142047.42660-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ixgbe_napi_add_all()/ixgbe_napi_del_all() are declared but never implemented in
commit 92915f71201b ("ixgbevf: Driver main and ethool interface module and main header")
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230803141904.15316-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 1e6e76101fd9 ("net: hns3: configure promisc mode for VF asynchronously")
left behind hclge_inform_vf_promisc_info() declaration.
And commit 68c0a5c70614 ("net: hns3: Add HNS3 IMP(Integrated Mgmt Proc) Cmd Interface Support")
declared but never implemented hclge_cmd_mdio_write() and hclge_cmd_mdio_read().
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230803135138.37456-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since platform_get_irq_byname() never returned zero, so it need not to
check whether it returned zero, it returned -EINVAL or -ENXIO when
failed, so we replace the return error code with the result it returned.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At present hwc timeout value is a fixed value. This patch sets the hwc
timeout from the hardware. It now uses a new hardware capability
GDMA_DRV_CAP_FLAG_1_HWC_TIMEOUT_RECONFIG to query and set the value
in hwc_timeout.
Signed-off-by: Souradeep Chakrabarti <schakrabarti@linux.microsoft.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a warning reported by coccinelle:
./drivers/net/ethernet/microchip/vcap/vcap_api.c:2399:9-16: WARNING:
ERR_CAST can be used with ri
Use ERR_CAST instead of ERR_PTR + PTR_ERR to simplify the
conversion process.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2023-08-03
This is a pull request of 9 patches for net-next/master.
The 1st patch is by Ruan Jinjie, targets the flexcan driver, and
cleans up the error handling of platform_get_irq() in the
flexcan_probe() function.
Markus Schneider-Pargmann contributes 6 patches for the tcan4x5x M_CAN
driver, consisting of some cleanups, and adding support for the
tcan4552/4553 chips.
Another patch by Ruan Jinjie, that cleans up the error path of
platform_get_irq() in the c_can_plat_probe() function of the C_CAN
platform driver.
The last patch is by Frank Jungclaus and adds support for the
CAN-USB/3 and CAN FD to the ESD USB CAN driver.
================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing include for DPAA (fix aarch64 build).
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202308040620.ty8oYNOP-lkp@intel.com/
Fixes: 680ee0456a57 ("net: invert the netdevice.h vs xdp.h dependency")
Reviewed-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20230803230008.362214-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Martin KaFai Lau says:
====================
pull-request: bpf-next 2023-08-03
We've added 54 non-merge commits during the last 10 day(s) which contain
a total of 84 files changed, 4026 insertions(+), 562 deletions(-).
The main changes are:
1) Add SO_REUSEPORT support for TC bpf_sk_assign from Lorenz Bauer,
Daniel Borkmann
2) Support new insns from cpu v4 from Yonghong Song
3) Non-atomically allocate freelist during prefill from YiFei Zhu
4) Support defragmenting IPv(4|6) packets in BPF from Daniel Xu
5) Add tracepoint to xdp attaching failure from Leon Hwang
6) struct netdev_rx_queue and xdp.h reshuffling to reduce
rebuild time from Jakub Kicinski
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (54 commits)
net: invert the netdevice.h vs xdp.h dependency
net: move struct netdev_rx_queue out of netdevice.h
eth: add missing xdp.h includes in drivers
selftests/bpf: Add testcase for xdp attaching failure tracepoint
bpf, xdp: Add tracepoint to xdp attaching failure
selftests/bpf: fix static assert compilation issue for test_cls_*.c
bpf: fix bpf_probe_read_kernel prototype mismatch
riscv, bpf: Adapt bpf trampoline to optimized riscv ftrace framework
libbpf: fix typos in Makefile
tracing: bpf: use struct trace_entry in struct syscall_tp_t
bpf, devmap: Remove unused dtab field from bpf_dtab_netdev
bpf, cpumap: Remove unused cmap field from bpf_cpu_map_entry
netfilter: bpf: Only define get_proto_defrag_hook() if necessary
bpf: Fix an array-index-out-of-bounds issue in disasm.c
net: remove duplicate INDIRECT_CALLABLE_DECLARE of udp[6]_ehashfn
docs/bpf: Fix malformed documentation
bpf: selftests: Add defrag selftests
bpf: selftests: Support custom type and proto for client sockets
bpf: selftests: Support not connecting client socket
netfilter: bpf: Support BPF_F_NETFILTER_IP_DEFRAG in netfilter link
...
====================
Link: https://lore.kernel.org/r/20230803174845.825419-1-martin.lau@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/dsa/port.c
9945c1fb03a3 ("net: dsa: fix older DSA drivers using phylink")
a88dd7538461 ("net: dsa: remove legacy_pre_march2020 detection")
https://lore.kernel.org/all/20230731102254.2c9868ca@canb.auug.org.au/
net/xdp/xsk.c
3c5b4d69c358 ("net: annotate data-races around sk->sk_mark")
b7f72a30e9ac ("xsk: introduce wrappers and helpers for supporting multi-buffer in Tx path")
https://lore.kernel.org/all/20230731102631.39988412@canb.auug.org.au/
drivers/net/ethernet/broadcom/bnxt/bnxt.c
37b61cda9c16 ("bnxt: don't handle XDP in netpoll")
2b56b3d99241 ("eth: bnxt: handle invalid Tx completions more gracefully")
https://lore.kernel.org/all/20230801101708.1dc7faac@canb.auug.org.au/
Adjacent changes:
drivers/net/ethernet/mellanox/mlx5/core/en_accel/ipsec_fs.c
62da08331f1a ("net/mlx5e: Set proper IPsec source port in L4 selector")
fbd517549c32 ("net/mlx5e: Add function to get IPsec offload namespace")
drivers/net/ethernet/sfc/selftest.c
55c1528f9b97 ("sfc: fix field-spanning memcpy in selftest")
ae9d445cd41f ("sfc: Miscellaneous comment removals")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf and wireless.
Nothing scary here. Feels like the first wave of regressions from v6.5
is addressed - one outstanding fix still to come in TLS for the
sendpage rework.
Current release - regressions:
- udp: fix __ip_append_data()'s handling of MSG_SPLICE_PAGES
- dsa: fix older DSA drivers using phylink
Previous releases - regressions:
- gro: fix misuse of CB in udp socket lookup
- mlx5: unregister devlink params in case interface is down
- Revert "wifi: ath11k: Enable threaded NAPI"
Previous releases - always broken:
- sched: cls_u32: fix match key mis-addressing
- sched: bind logic fixes for cls_fw, cls_u32 and cls_route
- add bound checks to a number of places which hand-parse netlink
- bpf: disable preemption in perf_event_output helpers code
- qed: fix scheduling in a tasklet while getting stats
- avoid using APIs which are not hardirq-safe in couple of drivers,
when we may be in a hard IRQ (netconsole)
- wifi: cfg80211: fix return value in scan logic, avoid page
allocator warning
- wifi: mt76: mt7615: do not advertise 5 GHz on first PHY of MT7615D
(DBDC)
Misc:
- drop handful of inactive maintainers, put some new in place"
* tag 'net-6.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (98 commits)
MAINTAINERS: update TUN/TAP maintainers
test/vsock: remove vsock_perf executable on `make clean`
tcp_metrics: fix data-race in tcpm_suck_dst() vs fastopen
tcp_metrics: annotate data-races around tm->tcpm_net
tcp_metrics: annotate data-races around tm->tcpm_vals[]
tcp_metrics: annotate data-races around tm->tcpm_lock
tcp_metrics: annotate data-races around tm->tcpm_stamp
tcp_metrics: fix addr_same() helper
prestera: fix fallback to previous version on same major version
udp: Fix __ip_append_data()'s handling of MSG_SPLICE_PAGES
net/mlx5e: Set proper IPsec source port in L4 selector
net/mlx5: fs_core: Skip the FTs in the same FS_TYPE_PRIO_CHAINS fs_prio
net/mlx5: fs_core: Make find_closest_ft more generic
wifi: brcmfmac: Fix field-spanning write in brcmf_scan_params_v2_to_v1()
vxlan: Fix nexthop hash size
ip6mr: Fix skb_under_panic in ip6mr_cache_report()
s390/qeth: Don't call dev_close/dev_open (DOWN/UP)
net: tap_open(): set sk_uid from current_fsuid()
net: tun_chr_open(): set sk_uid from current_fsuid()
net: dcb: choose correct policy to parse DCB_ATTR_BCN
...
|
|
ath.git patches for v6.6. Major changes:
ath12k
* Extremely High Throughput (EHT) PHY support for Wi-Fi 7
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.5
We did some house cleaning in MAINTAINERS file so several patches
about that. Few regressions fixed and also fix some recently enabled
memcpy() warnings. Only small commits and nothing special standing
out.
* tag 'wireless-2023-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: brcmfmac: Fix field-spanning write in brcmf_scan_params_v2_to_v1()
wifi: ray_cs: Replace 1-element array with flexible array
MAINTAINERS: add Jeff as ath10k, ath11k and ath12k maintainer
MAINTAINERS: wifi: mark mlw8k as orphan
MAINTAINERS: wifi: mark b43 as orphan
MAINTAINERS: wifi: mark zd1211rw as orphan
MAINTAINERS: wifi: mark wl3501 as orphan
MAINTAINERS: wifi: mark rndis_wlan as orphan
MAINTAINERS: wifi: mark ar5523 as orphan
MAINTAINERS: wifi: mark cw1200 as orphan
MAINTAINERS: wifi: atmel: mark as orphan
MAINTAINERS: wifi: rtw88: change Ping as the maintainer
Revert "wifi: ath6k: silence false positive -Wno-dangling-pointer warning on GCC 12"
wifi: cfg80211: Fix return value in scan logic
Revert "wifi: ath11k: Enable threaded NAPI"
MAINTAINERS: Update mwifiex maintainer list
wifi: mt76: mt7615: do not advertise 5 GHz on first phy of MT7615D (DBDC)
====================
Link: https://lore.kernel.org/r/20230803140058.57476C433C9@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When both supported and previous version have the same major version,
and the firmwares are missing, the driver ends in a loop requesting the
same (previous) version over and over again:
[ 76.327413] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.1.img firmware, fall-back to previous 4.0 version
[ 76.339802] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.352162] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.364502] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.376848] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.389183] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.401522] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.413860] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.426199] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
...
Fix this by inverting the check to that we aren't yet at the previous
version, and also check the minor version.
This also catches the case where both versions are the same, as it was
after commit bb5dbf2cc64d ("net: marvell: prestera: add firmware v4.0
support").
With this fix applied:
[ 88.499622] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.1.img firmware, fall-back to previous 4.0 version
[ 88.511995] Prestera DX 0000:01:00.0: failed to request previous firmware: mrvl/prestera/mvsw_prestera_fw-v4.0.img
[ 88.522403] Prestera DX: probe of 0000:01:00.0 failed with error -2
Fixes: 47f26018a414 ("net: marvell: prestera: try to load previous fw version")
Signed-off-by: Jonas Gorski <jonas.gorski@bisdn.de>
Acked-by: Elad Nachman <enachman@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Taras Chornyi <taras.chornyi@plvision.eu>
Link: https://lore.kernel.org/r/20230802092357.163944-1-jonas.gorski@bisdn.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
struct netdev_rx_queue is touched in only a few places
and having it defined in netdevice.h brings in the dependency
on xdp.h, because struct xdp_rxq_info gets embedded in
struct netdev_rx_queue.
In prep for removal of xdp.h from netdevice.h move all
the netdev_rx_queue stuff to a new header.
We could technically break the new header up to avoid
the sysfs.h include but it's so rarely included it
doesn't seem to be worth it at this point.
Reviewed-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20230803010230.1755386-3-kuba@kernel.org
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
Handful of drivers currently expect to get xdp.h by virtue
of including netdevice.h. This will soon no longer be the case
so add explicit includes.
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20230803010230.1755386-2-kuba@kernel.org
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
The NULL initialization of the pointers assigned by kzalloc() first is
not necessary, because if the kzalloc() failed, the pointers will be
assigned NULL, otherwise it works as usual. so remove it.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230802040026.2588675-1-ruanjinjie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
It is not possible for platform_get_irq() to return 0. Use the
return value from platform_get_irq().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20230802085216.659238-1-ruanjinjie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
It is not possible for platform_get_irq() to return 0. Use the
return value from platform_get_irq().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20230802090657.969923-1-ruanjinjie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
WiFi 7 chips doesn't have static const tables defined in driver. If tables
aren't loaded properly from firmware file, driver can get NULL pointer
access exception. One way is to add the checking statements when trying to
access these tables, but I choose to check them right after loading
firmware elements from firmware file, so I don't need to add error handlers
everywhere.
Currently, the needed firmware elements of WiFi 6 chips are all zero, and
coming WiFi 7 chip will need at least BB MCU, parameters of BB and RF.
We will add them after 8922AE is verified.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-9-pkshih@realtek.com
|
|
The tables of BB and RF parameters are pairs of {addr, value}. Load them
and convert from little-endian to CPU order, and show the version to clear
which version we are using.
rtw89_8922ae 0000:03:00.0: Firmware element BB version: 00 04 00 00
rtw89_8922ae 0000:03:00.0: Firmware element radio A version: 00 13 00 00
rtw89_8922ae 0000:03:00.0: Firmware element NCTL version: 00 05 00 00
We use tables defined in firmware elements with higher priority than
original static const tables defined in driver, because WiFi 7 chips will
not define the tables in driver, and existing chips can possibly migrate to
the new design one by one.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-8-pkshih@realtek.com
|
|
In order to pack more data into firmware file, we introduce firmware
elements and append BB_MCU firmware first. The first part of new firmware
file is still unchanged firmware of WiFi CPU, so the new firmware format
can be backward compatible to old format. The new elements part consists
of ID and size basically, which can append more elements simply. To avoid
unaligned access in certain platform and be easy to read, headers of all
elements start at 16-byte aligned address.
+===========================================+
| original firmware |
| +-------------+
| | padding |
+===========================================+
| elm ID 1 | elm size | other header data |
+----------+----------+ |
| |
+-------------------------------------------+
| content (variable length) |
| +-------------+
| | padding |
+===========================================+
| elm ID 2 | elm size | other header data |
+----------+----------+ |
| |
+-------------------------------------------+
| content (variable length) |
| +-----------------------+
| | (no padding for the last one)
+===================+
More detail of element header is shown below. The additional fields
'version' and 'element_priv[]' are meta data of elements, so that we can
know element version easily, and element_priv[] provide specific fields
for certain element, such as RF path index for RF parameter tables.
+===========================================+
| elm ID | elm size | version | rsvd0 |
+----------+----------+----------+----------+
| rsvd1/2 | element_priv[] |
+-------------------------------------------+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-7-pkshih@realtek.com
|
|
For existing chips, firmware is only for WiFi CPU, but WiFi 7 chips add
new hardware component BB MCU that needs firmware as well. The firmwares of
BB MCU 0/1 are also downloaded via the same path like WiFi CPU firmware,
and use the same firmware header format, so add firmware suits to access
them commonly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-6-pkshih@realtek.com
|
|
A firmware with v1 format contains many sections to download. Add parser to
read section type, target address, length, checksum and so on, and then
download the section to WiFi CPU with proper location.
The additional dynamic header length named dynamic_hdr_len is used to
skip content of dynamic header containing compiler flags of firmware, which
can help to determine variant firmware build, but currently rtw89 only
use single one variant. So, just skip the content.
The layout of a WiFi CPU firmware with v1 format looks like:
+---------------------------------------+
| Header (12 words) |
+---------------------------------------+
| Section header 1 (4 words) |
| Section header 2 (4 words) |
| Section header 3 (4 words) |
| ... |
+---------------------------------------+
| Dynamic header (variable length) |
+---------------------------------------+
| Data used & pointed by section |
| ... |
+---------------------------------------+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-5-pkshih@realtek.com
|
|
New firmware header is used by upcoming WiFi 7 chips to have more
information, so use common field w3[31:24] to determine header version,
and then use corresponding function to read firmware version and commit ID:
rtw89_8852be 0000:03:00.0: Firmware version 0.29.29.1 (799134c3), cmd version 1, type 5
rtw89_8852be 0000:03:00.0: Firmware version 0.29.29.1 (799134c3), cmd version 1, type 3
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-4-pkshih@realtek.com
|
|
Original firmware log which is sent via C2H message bloats
code size of firmware and is also length-limited. So we put
some common log into format file, and firmware could use a
log ID and some variables in C2H message to map a formatted
text via pre-designed rule.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-3-pkshih@realtek.com
|
|
Firmware log format is an element of multi-firmware file
and used for firmware to provide log with formatted text.
Driver needs to recognize it in advance if it exists.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-2-pkshih@realtek.com
|
|
NETSYS_V3 uses 64 bits for each counters while older SoCs are using
48/40 bits for each counter.
Support reading per-flow byte and package counters on NETSYS_V3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/37a0928fa8c1253b197884c68ce1f54239421ac5.1690946442.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Deadlock is easily happened while shutdown wlan interface such as run
"ifconfig wlan0 down".
The reason is because when ar->regd_update_work is ran, it will
call wiphy_lock(ar->hw->wiphy) in function ath12k_regd_update() which
is running in workqueue of ieee80211_local queued by ieee80211_queue_work().
Another thread from "ifconfig wlan0 down" will also accuqire the lock
by wiphy_lock(sdata->local->hw.wiphy) in function ieee80211_stop(), and
then it call ieee80211_stop_device() to flush_workqueue(local->workqueue),
this will wait the workqueue of ieee80211_local finished. Then deadlock
will happen easily if the two thread run meanwhile.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230718024724.29120-1-quic_wgong@quicinc.com
|
|
When wlan interface is up, and 11d scan is sent to the firmware, then
firmware needs to spend couple of seconds to complete the 11d scan. If
normal scan from user space arrives to ath12k at this moment, then the
normal scan request is also sent to the firmware, but the scan started
event will be reported to ath12k until the 11d scan complete. When timed
out for the scan started in ath12k, ath12k stops the normal scan and the
firmware reports WMI_SCAN_EVENT_DEQUEUED to ath12k for the normal scan.
ath12k has no handler for the event and then timed out for the scan
completed in ath12k_scan_stop(), and ath12k prints the following error
message.
[ 1491.604750] ath12k_pci 0000:02:00.0: failed to receive scan abort comple: timed out
[ 1491.604756] ath12k_pci 0000:02:00.0: failed to stop scan: -110
[ 1491.604758] ath12k_pci 0000:02:00.0: failed to start hw scan: -110
Add a handler for WMI_SCAN_EVENT_DEQUEUED and then complete the scan to
get rid of the above error message.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230717034457.22162-1-quic_wgong@quicinc.com
|
|
In ath12k_mac_vif_unref() dp->tx_desc_used_list[i]
is not altered so list_for_each_entry() should be safe.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230704173718.73462-1-dmantipov@yandex.ru
|
|
Enable the feature flag to indicate the driver support for
preamble puncturing. Firmware will support this feature
by default from IEEE 802.11be onwards.
Configure the bitmap as part of VDEV start/restart and
peer association commands.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-12-quic_alokad@quicinc.com
|
|
Parse WMI service ready ext2 event.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-11-quic_alokad@quicinc.com
|
|
Add tags with length 0 for MLO header and partner links which
are required by the firmware for a successful association.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-10-quic_alokad@quicinc.com
|
|
Add required peer association definitions and processing if the
bandwidth is 320 MHz.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu<quic_pradeepc@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-9-quic_alokad@quicinc.com
|
|
Add new WMI tag and pass the EHT parameters for peer association
to firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-8-quic_alokad@quicinc.com
|
|
Add new parameters and prepare the association data for an EHT peer.
MCS data uses the format described in IEEE P802.11be/D2.0, May 2022,
9.4.2.313.4, convert it into the format expected by the firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-7-quic_alokad@quicinc.com
|
|
Add support to retrieve and configure the phy modes supported
by the hardware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-6-quic_alokad@quicinc.com
|
|
Propagate EHT capabilities to the userspace using a new member
'eht_cap' in structure ieee80211_sband_iftype_data.
MCS-NSS capabilities are copied depending on the supported bandwidths
for the given band.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu<quic_pradeepc@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-5-quic_alokad@quicinc.com
|