| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Checking skb->len against ETH_FRAME_LEN assumes a 1514
ethernet frame size. With an 802.1Q VLAN header, ethernet
frame length can now be 1518. Validate frame length against that.
Signed-off-by: Ian Coolidge <iancoolidge@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
INGPADBOUNDARY_MASK is already shifted. No need to shift it again. On reloading
a driver it was resulting in a bad SGE FL MTU sizes [1536, 9088] error. This
only causes an issue on systems that have L1 cache size of 32B, 128B, 512B,
2048B or 4096B.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It doesn't make much sense to enable ISDN services if you don't
intend to connect to a network. Therefore insisting that ISDN
depends on NETDEVICES seems logical. We can then remove any
guards mentioning NETDEVICES inside all subordinate drivers.
This also has the nice side-effect of fixing the warning below
when ISDN_I4L && !CONFIG_NETDEVICES at compile time.
This patch fixes:
drivers/isdn/i4l/isdn_common.c: In function ‘isdn_ioctl’:
drivers/isdn/i4l/isdn_common.c:1278:8: warning: unused variable ‘s’ [-Wunused-variable]
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should not assume reserve fields to be don't cares as fields may change.
Clearing data structures before using.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correct spelling typo in bnx2x driver
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
f7b2927 introduced tx checksum offload support for smsc95xx,
and enabled it by default. This feature doesn't take
endianness into account, so causes most tx to fail on
those platforms.
This patch fixes the problem fully by adding the missing
conversion.
An alternate workaround is to disable TX checksum offload
on those platforms. The cpu impact of this feature is very low.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RTL_GIGA_MAC_VER_35 includes no multicast hardware filter.
Signed-off-by: Nathan Walp <faceprint@faceprint.com>
Suggested-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This regression was spotted between Debian squeeze and Debian wheezy
kernels (respectively based on 2.6.32 and 3.2). More info about
Wake-on-LAN issues with Realtek's 816x chipsets can be found in the
following thread: http://marc.info/?t=132079219400004
Probable regression from d4ed95d796e5126bba51466dc07e287cebc8bd19;
more chipsets are likely affected.
Tested on top of a 3.2.23 kernel.
Reported-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Tested-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Hinted-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Cyril Brulebois <kibi@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some driver uses tasklet_disable in device remove/close process,
tasklet_disable will inc tasklet->count and return. If the tasklet
is not handled yet because some softirq pressure, the tasklet will
placed on the tasklet_vec, never have a chance to excute. This might
lead to ksoftirqd heavy loaded, wakeup with pending_softirq, but
tasklet is disabled. tasklet_kill should be used in this case.
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"First post-Sandy pull request"
1) Fix antenna gain handling and initialization of chan->max_reg_power
in wireless, from Felix Fietkau.
2) Fix nexthop handling in H.232 conntrack helper, from Julian
Anastasov.
3) Only process 80211 mesh config header in certain kinds of frames,
from Javier Cardona.
4) 80211 management frame header length needs to be validated, from
Johannes Berg.
5) Don't access free'd SKBs in ath9k driver, from Felix Fietkay.
6) Test for permanent state correctly in VXLAN driver, from Stephen
Hemminger.
7) BNX2X bug fixes from Yaniv Rosner and Dmitry Kravkov.
8) Fix off by one errors in bonding, from Nikolay ALeksandrov.
9) Fix divide by zero in TCP-Illinois congestion control. From Jesper
Dangaard Brouer.
10) TCP metrics code says "Yo dawg, I heard you like sizeof, so I did a
sizeof of a sizeof, so you can size your size" Fix from Julian
Anastasov.
11) Several drivers do mdiobus_free without first doing an
mdiobus_unregister leading to stray pointer references. Fix from
Peter Senna Tschudin.
12) Fix OOPS in l2tp_eth_create() error path, it's another danling
pointer kinda situation. Fix from Tom Parkin.
13) Hardware driven by the vmxnet driver can't handle larger than 16K
fragments, so split them up when necessary. From Eric Dumazet.
14) Handle zero length data length in tcp_send_rcvq() properly. Fix
from Pavel Emelyanov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
tcp-repair: Handle zero-length data put in rcv queue
vmxnet3: must split too big fragments
l2tp: fix oops in l2tp_eth_create() error path
cxgb4: Fix unable to get UP event from the LLD
drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free
drivers/net/ethernet/nxp/lpc_eth.c: Call mdiobus_unregister before mdiobus_free
bnx2x: fix HW initialization using fw 7.8.x
tcp: Fix double sizeof in new tcp_metrics code
net: fix divide by zero in tcp algorithm illinois
net: sctp: Fix typo in net/sctp
bonding: fix second off-by-one error
bonding: fix off-by-one error
bnx2x: Disable FCoE for 57840 since not yet supported by FW
bnx2x: Fix no link on 577xx 10G-baseT
bnx2x: Fix unrecognized SFP+ module after driver is loaded
bnx2x: Fix potential incorrect link speed provision
bnx2x: Restore global registers back to default.
bnx2x: Fix link down in 57712 following LFA
bnx2x: Fix 57810 1G-KR link against certain switches.
ixgbe: PTP get_ts_info missing software support
...
|
|
vmxnet3 has a 16Kbytes limit per tx descriptor, that happened to work
as long as we provided PAGE_SIZE fragments.
Our stack can now build larger fragments, so we need to split them to
the 16kbytes boundary.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: jongman heo <jongman.heo@samsung.com>
Tested-by: jongman heo <jongman.heo@samsung.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Reviewed-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If T4 configuration file gets loaded from the /lib/firmware/cxgb4/ directory
then offload capabilities of the cards were getting disabled during
initialization. Hence ULDs do not get an UP event from the LLD.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on commit b27393aecf66199f5ddad37c302d3e0cfadbe6c0
Calling mdiobus_free without calling mdiobus_unregister causes
BUG_ON(). This patch fixes the issue.
The semantic patch that found this issue(http://coccinelle.lip6.fr/):
// <smpl>
@@
expression E;
@@
... when != mdiobus_unregister(E);
+ mdiobus_unregister(E);
mdiobus_free(E);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on commit b27393aecf66199f5ddad37c302d3e0cfadbe6c0
Calling mdiobus_free without calling mdiobus_unregister causes
BUG_ON(). This patch fixes the issue.
The semantic patch that found this issue(http://coccinelle.lip6.fr/):
// <smpl>
@@
expression E;
@@
... when != mdiobus_unregister(E);
+ mdiobus_unregister(E);
mdiobus_free(E);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 96bed4b9 (use FW 7.8.2) BRB HW block needs to be
initialized using fw values for all devices.
Otherwise ETS on 57712/578xx will not work.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management update from Rafael J. Wysocki:
"Change the email address of the powernow-k8 maintainer."
* tag 'pm-for-3.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq / powernow-k8: Change maintainer's email address
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem fixes from Dmitry Torokhov:
"Just a few driver fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: tsc40 - remove wrong announcement of pressure support
Input: lpc32xx-keys - select INPUT_MATRIXKMAP
Input: pxa27x_keypad - clear pending interrupts on keypad config
Input: wacom - correct bad Cintiq 24HD check
Input: wacom - add INPUT_PROP_DIRECT flag to Cintiq 24HD
Input: egalax_ts - get gpio from devicetree
|
|
Pull more scsi target fixes from Nicholas Bellinger:
"This series is a second round of target fixes for v3.7-rc4 that have
come into target-devel over the last days, and are important enough to
be applied ASAP.
All are being CC'ed to stable. The most important two are:
- target: Re-add explict zeroing of INQUIRY bounce buffer memory to
fix a regression for handling zero-length payloads, a bug that went
during v3.7-rc1, and hit >= v3.6.3 stable. (nab + paolo)
- iscsi-target: Fix a long-standing missed R2T wakeup race in TX
thread processing when using a single queue slot. (Roland)
Thanks to Roland & PureStorage team for helping to track down this
long standing race with iscsi-target single queue slot operation.
Also, the tcm_fc(FCoE) regression bug that was observed recently with
-rc2 code has also been resolved with the cancel_delayed_work() return
bugfix (commit c0158ca64da5: "workqueue: cancel_delayed_work() should
return %false if work item is idle") now in -rc3. Thanks again to Yi
Zou, MDR, Robert Love @ Intel for helping to track this down."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix incorrect usage of nested IRQ spinlocks in ABORT_TASK path
iscsi-target: Fix missed wakeup race in TX thread
target: Avoid integer overflow in se_dev_align_max_sectors()
target: Don't return success from module_init() if setup fails
target: Re-add explict zeroing of INQUIRY bounce buffer memory
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"An e-mail address update, and fix a compile error on SPARC"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: Only include of_match_table with CONFIG_OF_GPIO
hwmon, fam15h_power: Change email address, MAINTAINERS entry
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bugfixes from Konrad Rzeszutek Wilk:
- Use appropriate macros instead of hand-rolling our own (ARM).
- Fixes if FB/KBD closed unexpectedly.
- Fix memory leak in /dev/gntdev ioctl calls.
- Fix overflow check in xenbus_file_write.
- Document cleanup.
- Performance optimization when migrating guests.
* tag 'stable/for-linus-3.7-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/mmu: Use Xen specific TLB flush instead of the generic one.
xen/arm: use the __HVC macro
xen/xenbus: fix overflow check in xenbus_file_write()
xen-kbdfront: handle backend CLOSED without CLOSING
xen-fbfront: handle backend CLOSED without CLOSING
xen/gntdev: don't leak memory from IOCTL_GNTDEV_MAP_GRANT_REF
x86: remove obsolete comment from asm/xen/hypervisor.h
|
|
The following fixes build errors on sparc. Without any DT support,
of_match_ptr is NULL and the below is a no-op. However, if just
CONFIG_OF is defined then so is of_match_ptr.
All useful parts of the gpio-fan DT support rely on CONFIG_OF_GPIO
anyway, so of_match_table should too.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix off-by-one error because IFNAMSIZ == 16 and when this
code gets executed we stick a NULL byte where we should not.
How to reproduce:
with CONFIG_CC_STACKPROTECTOR=y (otherwise it may pass by silently)
modprobe bonding; echo 1 > /sys/class/net/bond0/bonding/mode;
echo "AAAAAAAAAAAAAAAA" > /sys/class/net/bond0/bonding/active_slave;
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Note: Sorry for the second patch but I missed this one while checking
the file. You can squash them into one patch.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix off-by-one error because IFNAMSIZ == 16 and when this
code gets executed we stick a NULL byte where we should not.
How to reproduce:
with CONFIG_CC_STACKPROTECTOR=y (otherwise it may pass by silently)
modprobe bonding; echo 1 > /sys/class/net/bond0/bonding/mode;
echo "AAAAAAAAAAAAAAAA" > /sys/class/net/bond0/bonding/primary;
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the Warpcore supports various link types, need to set only the correct
supported modes for XFI which is the serdes interface for the 10G-baseT PHY.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When SFP+ module is plugged in after driver is already loaded, it may not be
recognized, so set SFP module recognition time up to 300ms, without resetting
the module power in the middle.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix possible incorrect link speed provision following rapid link speed change.
Clear link speed mask after each link change, and not only after link down.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several KR registers were not set correctly back to default after
loopback test, so set those global registers over the global WC lane (zero)
rather than the current lane.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of link flap avoidance between PXE boot and bnx2x, set the appropriate
PHY DEVAD even if LFA kicks in.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix 1G KR link by restoring CL72 misc control register to default value rather
than 0.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch corrects the ethtool get_ts_info functon which did not state that
software timestamping was supported, even though it is.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
CC: Stable <stable@vger.kernel.org> [3.5]
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes core_tmr_abort_task() to use spin_lock -> spin_unlock
around se_cmd->t_state_lock while spin_lock_irqsave is held via
se_sess->sess_cmd_lock.
Signed-off-by: Steve Hodgson <steve@purestorage.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The sleeping code in iscsi_target_tx_thread() is susceptible to the classic
missed wakeup race:
- TX thread finishes handle_immediate_queue() and handle_response_queue(),
thinks both queues are empty.
- Another thread adds a queue entry and does wake_up_process(), which does
nothing because the TX thread is still awake.
- TX thread does schedule_timeout() and sleeps forever.
In practice this can kill an iSCSI connection if for example an initiator
does single-threaded writes and the target misses the wakeup window when
queueing an R2T; in this case the connection will be stuck until the
initiator loses patience and does some task management operation (or kills
the connection entirely).
Fix this by converting to wait_event_interruptible(), which does not
suffer from this sort of race.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The expression (max_sectors * block_size) might overflow a u32
(indeed, since iblock sets max_hw_sectors to UINT_MAX, it is
guaranteed to overflow and end up with a much-too-small result in many
common cases). Fix this by doing an equivalent calculation that
doesn't require multiplication.
While we're touching this code, avoid splitting a printk format across
two lines and use pr_info(...) instead of printk(KERN_INFO ...).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
If the call to core_dev_release_virtual_lun0() fails, then nothing
sets ret to anything other than 0, so even though everything is
torn down and freed, target_core_init_configfs() will seem to succeed
and the module will be loaded. Fix this by passing the return value
on up the chain.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a regression in spc_emulate_inquiry() code where the
local scope bounce buffer was no longer getting it's memory zeroed,
causing various problems with SCSI initiators that depend upon areas
of INQUIRY EVPD=0x83 payload having been zeroed.
This bug was introduced with the following v3.7-rc1 patch + CC'ed
stable commit:
commit ffe7b0e9326d9c68f5688bef691dd49f1e0d3651
Author: Paolo Bonzini <pbonzini@redhat.com>
Date: Fri Sep 7 17:30:38 2012 +0200
target: support zero allocation length in INQUIRY
Go ahead and re-add the missing memset of bounce buffer memory to be
copied into the outgoing se_cmd descriptor kmapped SGL payload.
Reported-by: Kelsey Prantis <kelsey.prantis@intel.com>
Cc: Kelsey Prantis <kelsey.prantis@intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Pull scsi target fixes from Nicholas Bellinger:
"These are the current target pending fixes headed for v3.7-rc4 code.
This includes the following highlights:
- Fix long-standing qla2xxx target bug where certain fc_port_t state
transitions could cause the internal session b-tree list to become
out-of-sync. (Roland)
- Fix task management double free of se_cmd descriptor in exception
path for users of target_submit_tmr(). (nab)
- Re-introduce simple NOP emulation of REZERO_UNIT, SEEK_6, and
SEEK_10 SCSI-2 commands in order to support legacy initiators that
still require them. (Bernhard)
Note these three patches are also CC'ed to stable.
Also, there a couple of outstanding (external) regressions that are
still being tracked down for tcm_fc(FCoE) and tcm_vhost fabrics for
v3.7.0 code, so please expect another PULL as these issues identified
-> resolved."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: reintroduce some obsolete SCSI-2 commands
target: Fix double-free of se_cmd in target_complete_tmr_failure
qla2xxx: Update target lookup session tables when a target session changes
tcm_qla2xxx: Format VPD page 83h SCSI name string according to SPC
qla2xxx: Add missing ->vport_slock while calling qlt_update_vp_map
|
|
Pull nouveau fixes from Dave Airlie:
"Just a nouveau set, since we have a couple of reports on lkml and
dri-devel of regressions that this should fix I sent it along on its
own."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: headless mode by default if pci class != vga display
drm/nouveau: resurrect headless mode since rework
drm/nv50/fb: prevent oops on chipsets without compression tags
drm/nouveau: allow creation of zero-sized mm
drm/nouveau/i2c: fix typo when checking nvio i2c port validity
drm/nouveau: silence modesetting spam on pre-gf8 chipsets
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
"This contains fixes for two devices by Jiri Slaby and Xianhan Yu, new
device IDs for MacBook Pro 10,2 from Dirk Hohndel and generic
multitouch code fix from Alan Cox."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Add support for the MacBook Pro 10,2 keyboard / touchpad
HID: multitouch: fix maxcontacts problem on GeneralTouch
HID: multitouch: put the case in the right switch statement
HID: microsoft: fix invalid rdesc for 3k kbd
|
|
Change the Andreas' email address in drivers/cpufreq/powernow-k8.c.
Signed-off-by: Andreas Herrmann <herrmann.der.user@googlemail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
This is a batch of fixes intended for 3.7...
The biggest portion of this is a pull request from Johannes Berg:
"Please pull my mac80211.git tree per below to get a number of fixes. I
have included a patch from Antonio to fix a memcpy overrun, Felix's
patches for the antenna gain/tx power issues, a few mesh-related fixes
from Javier for mac80211 and my own patches to not access data that
might not be present in an skb at all as well as a patch (the duplicate
IE check one) to make mac80211 forward-compatible with potential future
spec extensions that use the same IE multiple times.
It's a bit bigger than I'd like maybe, but I think all of these are
worthwhile fixes at this point."
In addition...
Felix Fietkau fixes an ath9k use-after-free issue.
Stanislaw Gruszka adds a valid value check to rt2800.
Sven Eckelmann adds a check to only check a TID value in a BlockAck, for
frames that could be either a BlockAck or a normal Ack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VXLAN confused flag versus bitmap on state.
Based on part of a earlier patch by David Stevens.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
This enables the existing drivers for keyboard and touchpad with the new
USB IDs found on the MBP 13" Reasonable Resolution (also known as the
Retina Display).
Added entries to both keyboard and mouse ignore lists.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Fix maxcontacts problem for PWT GeneralTouch multi-touchscreen.
Our device didn't contain HID_DG_CONTACTMAX usage. This usage use to describe
touchscreen's maxcontacts for hid-multitouch.c to get maxcontacts automatic. We
fix the device that driver can get maxcontact from our device, hence it doesn't
need .maxcontact=10. Now there is just one device class can fix all our PWT
touchscreen.
Signed-off-by: Xianhan Yu <aroundight77@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Microsoft Digital Media Keyboard 3000 has two interfaces, and the
second one has a report descriptor with a bug. The second collection
says:
05 01 -- global; usage page -- 01 -- Generic Desktop Controls
09 80 -- local; usage -- 80 -- System Control
a1 01 -- main; collection -- 01 -- application
85 03 -- global; report ID -- 03
19 00 -- local; Usage Minimum -- 00
29 ff -- local; Usage Maximum -- ff
15 00 -- global; Logical Minimum -- 0
26 ff 00 -- global; Logical Maximum -- ff
81 00 -- main; input
c0 -- main; End Collection
I.e. it makes us think that there are all kinds of usages of system
control. That the keyboard is a not only a keyboard, but also a
joystick, mouse, gamepad, keypad, etc. The same as for the Wireless
Desktop Receiver, this should be Physical Min/Max. So fix that
appropriately.
References: https://bugzilla.novell.com/show_bug.cgi?id=776834
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The tsc40 driver announces it supports the pressure event, but will never
send one. The announcement will cause tslib to wait for such events and
sending all touch events with a pressure of 0. Removing the announcement
will make tslib fall back to emulating the pressure on touch events so
everything works as expected.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This is to prevent nouveau from taking over the console on headless boards
such as Tesla.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Pull md fixes from NeilBrown:
"Some fixes for md in 3.7
- one recently introduced crash for dm-raid10 with discard
- one bug in new functionality that has been around for a few
releases.
- minor bug in md's 'faulty' personality
and UAPI disintegration for md."
* tag 'md-3.7-fixes' of git://neil.brown.name/md:
MD RAID10: Fix oops when creating RAID10 arrays via dm-raid.c
md/raid1: Fix assembling of arrays containing Replacements.
md faulty: use disk_stack_limits()
UAPI: (Scripted) Disintegrate include/linux/raid
|
