Age | Commit message (Collapse) | Author | Files | Lines |
|
[ Upstream commit 996d585b079ad494a30cac10e08585bcd5345125 ]
Add Synaptics IDs in trackpoint_start_protocol() to mark them as valid.
Signed-off-by: Vincent Huang <vincent.huang@tw.synaptics.com>
Fixes: 6c77545af100 ("Input: trackpoint - add new trackpoint variant IDs")
Reviewed-by: Harry Cutts <hcutts@chromium.org>
Tested-by: Harry Cutts <hcutts@chromium.org>
Link: https://lore.kernel.org/r/20200924053013.1056953-1-vincent.huang@tw.synaptics.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8947efc077168c53b84d039881a7c967086a248a ]
Due to a HW issue, in some scenarios the LAST bit might remain set.
This will cause an unexpected NACK after reading 16 bytes on the next
read.
Example: if user tries to read from a missing device, get a NACK,
then if the next command is a long read ( > 16 bytes),
the master will stop reading after 16 bytes.
To solve this, if a command fails, check if LAST bit is still
set. If it does, reset the module.
Fixes: 56a1485b102e (i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver)
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a2bd970aa62f2f7f80fd0d212b1d4ccea5df4aed ]
the i2c_ram structure is missing the sdmatmp field mentionned in
datasheet for MPC8272 at paragraph 36.5. With this field missing, the
hardware would write past the allocated memory done through
cpm_muram_alloc for the i2c_ram structure and land in memory allocated
for the buffers descriptors corrupting the cbd_bufaddr field. Since this
field is only set during setup(), the first i2c transaction would work
and the following would send data read from an arbitrary memory
location.
Fixes: 61045dbe9d8d ("i2c: Add support for I2C bus on Freescale CPM1/CPM2 controllers")
Signed-off-by: Nicolas VINCENT <nicolas.vincent@vossloh.com>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3e640b1eec38e4c8eba160f26cba4f592e657f3d ]
GPIO_U is mapped to the least significant byte of input/output mask, and
the byte in "output" mask should be 0 because GPIO_U is input only. All
the other bits need to be 1 because GPIO_V/W/X support both input and
output modes.
Similarly, GPIO_Y/Z are mapped to the 2 least significant bytes, and the
according bits need to be 1 because GPIO_Y/Z support both input and
output modes.
Fixes: ab4a85534c3e ("gpio: aspeed: Add in ast2600 details to Aspeed driver")
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bf0d394e885015941ed2d5724c0a6ed8d42dd95e ]
Currently, the IRQ setup for the SGPIO driver enables all interrupts in
dual-edge trigger mode. Since the default handler is handle_bad_irq, any
state change on input GPIOs will trigger bad IRQ warnings.
This change applies sensible IRQ defaults: single-edge trigger, and all
IRQs disabled.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae79b ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ac67b07e268d46eba675a60c37051bb3e59fd201 ]
Currently, the aspeed-sgpio driver exposes up to 80 GPIO lines,
corresponding to the 80 status bits available in hardware. Each of these
lines can be configured as either an input or an output.
However, each of these GPIOs is actually an input *and* an output; we
actually have 80 inputs plus 80 outputs.
This change expands the maximum number of GPIOs to 160; the lower half
of this range are the input-only GPIOs, the upper half are the outputs.
We fix the GPIO directions to correspond to this mapping.
This also fixes a bug when setting GPIOs - we were reading from the
input register, making it impossible to set more than one output GPIO.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae79b ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e43c26e12dd49a41cf5a4cd5c5b59a1eb98ed11e ]
When pca953x_irq_pending returns false, the pending parameter won't
be set. But pca953x_irq_handler continues using this uninitialized
variable as pending irqs and will cause problem.
Fix the issue by initializing pending to 0.
Fixes: 064c73afe738 ("gpio: pca953x: Synchronize interrupt handler properly")
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1a26044954a6d1f4d375d5e62392446af663be7a ]
if of_find_device_by_node() succeed, exynos_iommu_of_xlate() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: aa759fd376fb ("iommu/exynos: Add callback for initializing devices from device tree")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200918011335.909141-1-yukuai3@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 149415586243bd0ea729760fb6dd7b3c50601871 ]
transport_lookup_tmr_lun() uses "orig_fe_lun" member of struct se_cmd for
the lookup. Hence, update this field directly for the
TARGET_SCF_LOOKUP_LUN_FROM_TAG case.
Link: https://lore.kernel.org/r/1600300471-26135-1-git-send-email-sudhakar.panneerselvam@oracle.com
Fixes: a36840d80027 ("target: Initialize LUN in transport_init_se_cmd()")
Reported-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Sudhakar Panneerselvam <sudhakar.panneerselvam@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f3bb0f796f5ffe32f0fbdce5b1b12eb85511158f ]
The ChipID IO region has it's own clock, which is being disabled while
scanning for unused clocks. It turned out that some CPU hotplug, CPU idle
or even SOC firmware code depends on the reads from that area. Fix the
mysterious hang caused by entering deep CPU idle state by ignoring the
'chipid' clock during unused clocks scan, as there are no direct clients
for it which will keep it enabled.
Fixes: e062b571777f ("clk: exynos4: register clocks using common clock framework")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200922124046.10496-1-m.szyprowski@samsung.com
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ce65d55f92a67e247f4d799e581cf9fed677871c ]
Andy reported that commit 6b41030fdc79 ("dmaengine: dmatest:
Restore default for channel") broke his scripts for the case
where "busy" channel is used for configuration with expectation
that run command would do nothing. Instead, behavior was
(unintentionally) changed to treat such case as under-configuration
and progress with defaults, i.e. run command would start a test
with default setting for channel (which would use all channels).
Restore original behavior with tracking status of channel setter
so we can distinguish between misconfigured and under-configured
cases in run command and act accordingly.
Fixes: 6b41030fdc79 ("dmaengine: dmatest: Restore default for channel")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200922115847.30100-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2f878d04218c8b26f6d0ab26955ca6b03848a1ad ]
Include the Tegra driver's clk.h to pull in the prototype definition for
this function so that compilers don't warn about it being missing.
Fixes: 0ac65fc946d3 ("clk: tegra: Implement Tegra210 EMC clock")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5105660ee80862b85f7769626d0f936c18ce1885 ]
Commit bff1cef5f23a ("clk: tegra: Don't enable already enabled PLLs")
added checks to avoid enabling PLLs that have already been enabled by
the bootloader. However, the PLL_E configuration inherited from the
bootloader isn't necessarily the one that is needed for the kernel.
This can cause SATA to fail like this:
[ 5.310270] phy phy-sata.6: phy poweron failed --> -110
[ 5.315604] tegra-ahci 70027000.sata: failed to power on AHCI controller: -110
[ 5.323022] tegra-ahci: probe of 70027000.sata failed with error -110
Fix this by always programming the PLL_E. This ensures that any mis-
configuration by the bootloader will be overwritten by the kernel.
Fixes: bff1cef5f23a ("clk: tegra: Don't enable already enabled PLLs")
Reported-by: LABBE Corentin <clabbe@baylibre.com>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 63c3212e7a37d68c89a13bdaebce869f4e064e67 ]
Per the datasheet the i2c functions use MPP_Sel=0x1. They are documented
as using MPP_Sel=0x4 as well but mixing 0x1 and 0x4 is clearly wrong. On
the board tested 0x4 resulted in a non-functioning i2c bus so stick with
0x1 which works.
Fixes: d7ae8f8dee7f ("pinctrl: mvebu: pinctrl driver for 98DX3236 SoC")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20200907211712.9697-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 850280156f6421a404f2351bee07a0e7bedfd4c6 ]
If devm_phy_create() fails then we need to call of_clk_del_provider(node)
to undo the call to of_clk_add_provider().
Fixes: 71e2f5c5c224 ("phy: ti: Add a new SERDES driver for TI's AM654x SoC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200905124648.GA183976@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5fcface659aab7eac4bd65dd116d98b8f7bb88d5 ]
The raw interrupt status of GPIO maybe set before the interrupt is enabled,
which would trigger the interrupt event once enabled it from user side.
This is the case for edge interrupts only. Adding a clear operation when
setting interrupt type can avoid that.
There're a few considerations for the solution:
1) This issue is for edge interrupt only; The interrupts requested by users
are IRQ_TYPE_LEVEL_HIGH as default, so clearing interrupt when request
is useless.
2) The interrupt type can be set to edge when request and following up
with clearing it though, but the problem is still there once users set
the interrupt type to level trggier.
3) We can add a clear operation after each time of setting interrupt
enable bit, but it is redundant for level trigger interrupt.
Therefore, the solution is this patch seems the best for now.
Fixes: 9a3821c2bb47 ("gpio: Add GPIO driver for Spreadtrum SC9860 platform")
Signed-off-by: Taiping Lai <taiping.lai@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9e0e8dac985d4bd07d9e62922b9d189d3ca2fccf ]
The lldd may have made calls to delete a remote port or local port and
the delete is in progress when the cli then attempts to create a new
controller. Currently, this proceeds without error although it can't be
very successful.
Fix this by validating that both the host port and remote port are
present when a new controller is to be created.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 50b7c24390a53c78de546215282fb52980f1d7b7 ]
Currently, we use nvmeq->q_depth as the upper limit for a valid tag in
nvme_handle_cqe(), it is not correct. Because the available tag number
is recorded in tagset, which is not equal to nvmeq->q_depth.
The nvme driver registers interrupts for queues before initializing the
tagset, because it uses the number of successful request_irq() calls to
configure the tagset parameters. This allows a race condition with the
current tag validity check if the controller happens to produce an
interrupt with a corrupted CQE before the tagset is initialized.
Replace the driver's indirect tag check with the one already provided by
the block layer.
Signed-off-by: Xianting Tian <tian.xianting@h3c.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8b9e03cd08250c60409099c791e858157838d9eb ]
Some of the IS2 IP4_TCP_UDP keys are not correct, like L4_DPORT,
L4_SPORT and other L4 keys. This prevents offloaded tc-flower rules from
matching on src_port and dst_port for TCP and UDP packets.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b867eef4cf548cd9541225aadcdcee644669b9e1 ]
The SPIE register contains counts for the TX FIFO so any time the irq
handler was invoked we would attempt to process the RX/TX fifos. Use the
SPIM value to mask the events so that we only process interrupts that
were expected.
This was a latent issue exposed by commit 3282a3da25bd ("powerpc/64:
Implement soft interrupt replay in C").
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200904002812.7300-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 36050d8984ab743f9990a2eb97a0062fdc3d7bbd ]
The commit eb1f00237aca ("lockdep,trace: Expose tracepoints"), started to
expose us for tracepoints. This lead to the following RCU splat on an ARM64
Qcom board.
[ 5.529634] WARNING: suspicious RCU usage
[ 5.537307] sdhci-pltfm: SDHCI platform and OF driver helper
[ 5.541092] 5.9.0-rc3 #86 Not tainted
[ 5.541098] -----------------------------
[ 5.541105] ../include/trace/events/lock.h:37 suspicious rcu_dereference_check() usage!
[ 5.541110]
[ 5.541110] other info that might help us debug this:
[ 5.541110]
[ 5.541116]
[ 5.541116] rcu_scheduler_active = 2, debug_locks = 1
[ 5.541122] RCU used illegally from extended quiescent state!
[ 5.541129] no locks held by swapper/0/0.
[ 5.541134]
[ 5.541134] stack backtrace:
[ 5.541143] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.9.0-rc3 #86
[ 5.541149] Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
[ 5.541157] Call trace:
[ 5.568185] sdhci_msm 7864900.sdhci: Got CD GPIO
[ 5.574186] dump_backtrace+0x0/0x1c8
[ 5.574206] show_stack+0x14/0x20
[ 5.574229] dump_stack+0xe8/0x154
[ 5.574250] lockdep_rcu_suspicious+0xd4/0xf8
[ 5.574269] lock_acquire+0x3f0/0x460
[ 5.574292] _raw_spin_lock_irqsave+0x80/0xb0
[ 5.574314] __pm_runtime_suspend+0x4c/0x188
[ 5.574341] psci_enter_domain_idle_state+0x40/0xa0
[ 5.574362] cpuidle_enter_state+0xc0/0x610
[ 5.646487] cpuidle_enter+0x38/0x50
[ 5.650651] call_cpuidle+0x18/0x40
[ 5.654467] do_idle+0x228/0x278
[ 5.657678] cpu_startup_entry+0x24/0x70
[ 5.661153] rest_init+0x1a4/0x278
[ 5.665061] arch_call_rest_init+0xc/0x14
[ 5.668272] start_kernel+0x508/0x540
Following the path in pm_runtime_put_sync_suspend() from
psci_enter_domain_idle_state(), it seems like we end up using the RCU.
Therefore, let's simply silence the splat by informing the RCU about it
with RCU_NONIDLE.
Note that, this is a temporary solution. Instead we should strive to avoid
using RCU_NONIDLE (and similar), but rather push rcu_idle_enter|exit()
further down, closer to the arch specific code. However, as the CPU PM
notifiers are also using the RCU, additional rework is needed.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9fb030a70431a2a2a1b292dbf0b2f399cc072c16 ]
This patch sets skb->protocol before transmitting frames on the HDLC
device, so that a user listening on the HDLC device with an AF_PACKET
socket will see outgoing frames' sll_protocol field correctly set and
consistent with that of incoming frames.
1. Control frames in hdlc_cisco and hdlc_ppp
When these drivers send control frames, skb->protocol is not set.
This value should be set to htons(ETH_P_HDLC), because when receiving
control frames, their skb->protocol is set to htons(ETH_P_HDLC).
When receiving, hdlc_type_trans in hdlc.h is called, which then calls
cisco_type_trans or ppp_type_trans. The skb->protocol of control frames
is set to htons(ETH_P_HDLC) so that the control frames can be received
by hdlc_rcv in hdlc.c, which calls cisco_rx or ppp_rx to process the
control frames.
2. hdlc_fr
When this driver sends control frames, skb->protocol is set to internal
values used in this driver.
When this driver sends data frames (from upper stacked PVC devices),
skb->protocol is the same as that of the user data packet being sent on
the upper PVC device (for normal PVC devices), or is htons(ETH_P_802_3)
(for Ethernet-emulating PVC devices).
However, skb->protocol for both control frames and data frames should be
set to htons(ETH_P_HDLC), because when receiving, all frames received on
the HDLC device will have their skb->protocol set to htons(ETH_P_HDLC).
When receiving, hdlc_type_trans in hdlc.h is called, and because this
driver doesn't provide a type_trans function in struct hdlc_proto,
all frames will have their skb->protocol set to htons(ETH_P_HDLC).
The frames are then received by hdlc_rcv in hdlc.c, which calls fr_rx
to process the frames (control frames are consumed and data frames
are re-received on upper PVC devices).
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 83f9a9c8c1edc222846dc1bde6e3479703e8e5a3 ]
This driver is a virtual driver stacked on top of Ethernet interfaces.
When this driver transmits data on the Ethernet device, the skb->protocol
setting is inconsistent with the Ethernet header prepended to the skb.
This causes a user listening on the Ethernet interface with an AF_PACKET
socket, to see different sll_protocol values for incoming and outgoing
frames, because incoming frames would have this value set by parsing the
Ethernet header.
This patch changes the skb->protocol value for outgoing Ethernet frames,
making it consistent with the Ethernet header prepended. This makes a
user listening on the Ethernet device with an AF_PACKET socket, to see
the same sll_protocol value for incoming and outgoing frames.
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 52a3974feb1a3eec25d8836d37a508b67b0a9cd0 ]
Get and put the reference to the ctrl in the nvme_dev_open() and
nvme_dev_release() before and after module get/put for ctrl in char
device file operations.
Introduce char_dev relase function, get/put the controller and module
which allows us to fix the potential Oops which can be easily reproduced
with a passthru ctrl (although the problem also exists with pure user
access):
Entering kdb (current=0xffff8887f8290000, pid 3128) on processor 30 Oops: (null)
due to oops @ 0xffffffffa01019ad
CPU: 30 PID: 3128 Comm: bash Tainted: G W OE 5.8.0-rc4nvme-5.9+ #35
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.4
RIP: 0010:nvme_free_ctrl+0x234/0x285 [nvme_core]
Code: 57 10 a0 e8 73 bf 02 e1 ba 3d 11 00 00 48 c7 c6 98 33 10 a0 48 c7 c7 1d 57 10 a0 e8 5b bf 02 e1 8
RSP: 0018:ffffc90001d63de0 EFLAGS: 00010246
RAX: ffffffffa05c0440 RBX: ffff8888119e45a0 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff8888177e9550 RDI: ffff8888119e43b0
RBP: ffff8887d4768000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: ffffc90001d63c90 R12: ffff8888119e43b0
R13: ffff8888119e5108 R14: dead000000000100 R15: ffff8888119e5108
FS: 00007f1ef27b0740(0000) GS:ffff888817600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffa05c0470 CR3: 00000007f6bee000 CR4: 00000000003406e0
Call Trace:
device_release+0x27/0x80
kobject_put+0x98/0x170
nvmet_passthru_ctrl_disable+0x4a/0x70 [nvmet]
nvmet_passthru_enable_store+0x4c/0x90 [nvmet]
configfs_write_file+0xe6/0x150
vfs_write+0xba/0x1e0
ksys_write+0x5f/0xe0
do_syscall_64+0x52/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7f1ef1eb2840
Code: Bad RIP value.
RSP: 002b:00007fffdbff0eb8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007f1ef1eb2840
RDX: 0000000000000002 RSI: 00007f1ef27d2000 RDI: 0000000000000001
RBP: 00007f1ef27d2000 R08: 000000000000000a R09: 00007f1ef27b0740
R10: 0000000000000001 R11: 0000000000000246 R12: 00007f1ef2186400
R13: 0000000000000002 R14: 0000000000000001 R15: 0000000000000000
With this patch fix we take the module ref count in nvme_dev_open() and
release that ref count in newly introduced nvme_dev_release().
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ce4cc3133dc72c31bd49ddcf22d0f9eeff47a761 ]
The write zeros command does not work with 4k range.
bash-4.4# ./blkdiscard /dev/nvme0n1p2
bash-4.4# strace -efallocate xfs_io -c "fzero 536895488 2048" /dev/nvme0n1p2
fallocate(3, FALLOC_FL_ZERO_RANGE, 536895488, 2048) = 0
+++ exited with 0 +++
bash-4.4# dd bs=1 if=/dev/nvme0n1p2 skip=536895488 count=512 | hexdump -C
00000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
*
00000200
bash-4.4# ./blkdiscard /dev/nvme0n1p2
bash-4.4# strace -efallocate xfs_io -c "fzero 536895488 4096" /dev/nvme0n1p2
fallocate(3, FALLOC_FL_ZERO_RANGE, 536895488, 4096) = 0
+++ exited with 0 +++
bash-4.4# dd bs=1 if=/dev/nvme0n1p2 skip=536895488 count=512 | hexdump -C
00000000 5c 61 5c b0 96 21 1b 5e 85 0c 07 32 9c 8c eb 3c |\a\..!.^...2...<|
00000010 4a a2 06 ca 67 15 2d 8e 29 8d a8 a0 7e 46 8c 62 |J...g.-.)...~F.b|
00000020 bb 4c 6c c1 6b f5 ae a5 e4 a9 bc 93 4f 60 ff 7a |.Ll.k.......O`.z|
Reported-by: Eric Sandeen <esandeen@redhat.com>
Signed-off-by: David Milburn <dmilburn@redhat.com>
Tested-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4202c9fdf03d79dedaa94b2c4cf574f25793d669 ]
Some WinCE devices face connectivity issues via the NDIS interface. They
fail to register, resulting in -110 timeout errors and failures during the
probe procedure.
In this kind of WinCE devices, the Windows-side ndis driver needs quite
more time to be loaded and configured, so that the linux rndis host queries
to them fail to be responded correctly on time.
More specifically, when INIT is called on the WinCE side - no other
requests can be served by the Client and this results in a failed QUERY
afterwards.
The increase of the waiting time on the side of the linux rndis host in
the command-response loop leaves the INIT process to complete and respond
to a QUERY, which comes afterwards. The WinCE devices with this special
"feature" in their ndis driver are satisfied by this fix.
Signed-off-by: Olympia Giannou <olympia.giannou@leica-geosystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ee460417d254d941dfea5fb7cff841f589643992 ]
Increase Rx ring size to address issue where hardware is reaching
the receive work limit.
Before:
[ 102.223342] de2104x 0000:17:00.0 eth0: rx work limit reached
[ 102.245695] de2104x 0000:17:00.0 eth0: rx work limit reached
[ 102.251387] de2104x 0000:17:00.0 eth0: rx work limit reached
[ 102.267444] de2104x 0000:17:00.0 eth0: rx work limit reached
Signed-off-by: Lucy Yan <lucyyan@google.com>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit da26658c3d7005aa67a706dceff7b2807b59e123 ]
The previous change "hv_netvsc: Switch the data path at the right time
during hibernation" adds the call of netvsc_vf_changed() upon
NETDEV_CHANGE, so it's necessary to avoid the duplicate call and message
when the VF is brought UP or DOWN.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 74ea06164cda81dc80e97790164ca533fd7e3087 ]
Better guess. Secondary CSC registers are from 0xF0000.
Signed-off-by: Martin Cerveny <m.cerveny@computer.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200906162140.5584-3-m.cerveny@computer.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1264c1e0cfe55e2d6c35e869244093195529af37 ]
This patch causes a regression betwen Kernel 5.7 and 5.8 at wlcore:
with it applied, WiFi stops working, and the Kernel starts printing
this message every second:
wlcore: PHY firmware version: Rev 8.2.0.0.242
wlcore: firmware booted (Rev 8.9.0.0.79)
wlcore: ERROR command execute failure 14
------------[ cut here ]------------
WARNING: CPU: 0 PID: 133 at drivers/net/wireless/ti/wlcore/main.c:795 wl12xx_queue_recovery_work.part.0+0x6c/0x74 [wlcore]
Modules linked in: wl18xx wlcore mac80211 libarc4 cfg80211 rfkill snd_soc_hdmi_codec crct10dif_ce wlcore_sdio adv7511 cec kirin9xx_drm(C) kirin9xx_dw_drm_dsi(C) drm_kms_helper drm ip_tables x_tables ipv6 nf_defrag_ipv6
CPU: 0 PID: 133 Comm: kworker/0:1 Tainted: G WC 5.8.0+ #186
Hardware name: HiKey970 (DT)
Workqueue: events_freezable ieee80211_restart_work [mac80211]
pstate: 60000005 (nZCv daif -PAN -UAO BTYPE=--)
pc : wl12xx_queue_recovery_work.part.0+0x6c/0x74 [wlcore]
lr : wl12xx_queue_recovery_work+0x24/0x30 [wlcore]
sp : ffff8000126c3a60
x29: ffff8000126c3a60 x28: 00000000000025de
x27: 0000000000000010 x26: 0000000000000005
x25: ffff0001a5d49e80 x24: ffff8000092cf580
x23: ffff0001b7c12623 x22: ffff0001b6fcf2e8
x21: ffff0001b7e46200 x20: 00000000fffffffb
x19: ffff0001a78e6400 x18: 0000000000000030
x17: 0000000000000001 x16: 0000000000000001
x15: ffff0001b7e46670 x14: ffffffffffffffff
x13: ffff8000926c37d7 x12: ffff8000126c37e0
x11: ffff800011e01000 x10: ffff8000120526d0
x9 : 0000000000000000 x8 : 3431206572756c69
x7 : 6166206574756365 x6 : 0000000000000c2c
x5 : 0000000000000000 x4 : ffff0001bf1361e8
x3 : ffff0001bf1790b0 x2 : 0000000000000000
x1 : ffff0001a5d49e80 x0 : 0000000000000001
Call trace:
wl12xx_queue_recovery_work.part.0+0x6c/0x74 [wlcore]
wl12xx_queue_recovery_work+0x24/0x30 [wlcore]
wl1271_cmd_set_sta_key+0x258/0x25c [wlcore]
wl1271_set_key+0x7c/0x2dc [wlcore]
wlcore_set_key+0xe4/0x360 [wlcore]
wl18xx_set_key+0x48/0x1d0 [wl18xx]
wlcore_op_set_key+0xa4/0x180 [wlcore]
ieee80211_key_enable_hw_accel+0xb0/0x2d0 [mac80211]
ieee80211_reenable_keys+0x70/0x110 [mac80211]
ieee80211_reconfig+0xa00/0xca0 [mac80211]
ieee80211_restart_work+0xc4/0xfc [mac80211]
process_one_work+0x1cc/0x350
worker_thread+0x13c/0x470
kthread+0x154/0x160
ret_from_fork+0x10/0x30
---[ end trace b1f722abf9af5919 ]---
wlcore: WARNING could not set keys
wlcore: ERROR Could not add or replace key
wlan0: failed to set key (4, ff:ff:ff:ff:ff:ff) to hardware (-5)
wlcore: Hardware recovery in progress. FW ver: Rev 8.9.0.0.79
wlcore: pc: 0x0, hint_sts: 0x00000040 count: 39
wlcore: down
wlcore: down
ieee80211 phy0: Hardware restart was requested
mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 25000000Hz (slot req 25000000Hz, actual 25000000HZ div = 0)
wlcore: PHY firmware version: Rev 8.2.0.0.242
wlcore: firmware booted (Rev 8.9.0.0.79)
wlcore: ERROR command execute failure 14
------------[ cut here ]------------
Tested on Hikey 970.
This reverts commit 2b7aadd3b9e17e8b81eeb8d9cc46756ae4658265.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/f0a2cb7ea606f1a284d4c23cbf983da2954ce9b6.1598420968.git.mchehab+huawei@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 44a049c42681de71c783d75cd6e56b4e339488b0 ]
PVC devices are virtual devices in this driver stacked on top of the
actual HDLC device. They are the devices normal users would use.
PVC devices have two types: normal PVC devices and Ethernet-emulating
PVC devices.
When transmitting data with PVC devices, the ndo_start_xmit function
will prepend a header of 4 or 10 bytes. Currently this driver requests
this headroom to be reserved for normal PVC devices by setting their
hard_header_len to 10. However, this does not work when these devices
are used with AF_PACKET/RAW sockets. Also, this driver does not request
this headroom for Ethernet-emulating PVC devices (but deals with this
problem by reallocating the skb when needed, which is not optimal).
This patch replaces hard_header_len with needed_headroom, and set
needed_headroom for Ethernet-emulating PVC devices, too. This makes
the driver to request headroom for all PVC devices in all cases.
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b4be5a53ebf478ffcfb4c98c0ccc4a8d922b9a02 ]
Using dev_kfree_skb for tx skbs breaks AQL. This worked until now only
by accident, because a mac80211 issue breaks AQL on drivers with firmware
rate control that report the rate via ieee80211_tx_status_ext as struct
rate_info.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200812144943.91974-1-nbd@nbd.name
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bc6717d55d07110d8f3c6d31ec2af50c11b07091 ]
When the timer counts to the upper limit, an overflow interrupt is
generated, and the count is reset with the value in the TIME_INI
register. But the software expects to start counting from 0 when
the count overflows, so it forces TIME_INI to 0 to solve the
potential interrupt storm problem.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Tested-by: Xu Kai <xukai@nationalchip.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1597735877-71115-1-git-send-email-guoren@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0891fb39ba67bd7ae023ea0d367297ffff010781 upstream.
Since commit c330fb1ddc0a ("XEN uses irqdesc::irq_data_common::handler_data to store a per interrupt XEN data pointer which contains XEN specific information.")
Xen is using the chip_data pointer for storing IRQ specific data. When
running as a HVM domain this can result in problems for legacy IRQs, as
those might use chip_data for their own purposes.
Use a local array for this purpose in case of legacy IRQs, avoiding the
double use.
Cc: stable@vger.kernel.org
Fixes: c330fb1ddc0a ("XEN uses irqdesc::irq_data_common::handler_data to store a per interrupt XEN data pointer which contains XEN specific information.")
Signed-off-by: Juergen Gross <jgross@suse.com>
Tested-by: Stefan Bader <stefan.bader@canonical.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20200930091614.13660-1-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a39d0d7bdf8c21ac7645c02e9676b5cb2b804c31 upstream.
A recent attempt to fix a ref count leak in
amdgpu_display_crtc_set_config() turned out to be doing too much and
"fixed" an intended decrease as if it were a leak. Undo that part to
restore the proper balance. This is the very nature of this function
to increase or decrease the power reference count depending on the
situation.
Consequences of this bug is that the power reference would
eventually get down to 0 while the display was still in use,
resulting in that display switching off unexpectedly.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: e008fa6fb415 ("drm/amdgpu: fix ref count leak in amdgpu_display_crtc_set_config")
Cc: stable@vger.kernel.org
Cc: Navid Emamdoost <navid.emamdoost@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 62c59a8786e6bb75569cee91dab66e9da3ff4b68 upstream.
After commit 6827ca573c03 ("memstick: rtsx_usb_ms: Support runtime power
management"), removing module rtsx_usb_ms will be stuck.
The deadlock is caused by powering on and powering off at the same time,
the former one is when memstick_check() is flushed, and the later is called
by memstick_remove_host().
Soe let's skip allocating card to prevent this issue.
Fixes: 6827ca573c03 ("memstick: rtsx_usb_ms: Support runtime power management")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20200925084952.13220-1-kai.heng.feng@canonical.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fdb29f4de1374483291232ae7515e5e7bb464762 upstream.
Remove superfluous '.c' from qcom-spmi-adc5 device driver name.
Fixes: e13d757279bb ("iio: adc: Add QCOM SPMI PMIC5 ADC driver")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200910140000.324091-2-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5fc27b098dafb8e30794a9db0705074c7d766179 upstream.
Touchpad on this laptop is not detected properly during boot, as PNP
enumerates (wrongly) AUX port as disabled on this machine.
Fix that by adding this board (with admittedly quite funny DMI
identifiers) to nopnp quirk list.
Reported-by: Andrés Barrantes Silman <andresbs2000@protonmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Link: https://lore.kernel.org/r/nycvar.YFH.7.76.2009252337340.3336@cbobk.fhfr.pm
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 845b89127bc5458d0152a4d63f165c62a22fcb70 upstream.
By default, PCI drivers with runtime PM enabled will skip the calls
to suspend and resume on system PM. For this driver, we don't want
that, as we need to perform additional steps for system PM to work
properly on all systems. So instruct the PM core to not skip these
calls.
Fixes: a9c8088c7988 ("i2c: i801: Don't restore config registers on runtime PM")
Reported-by: Volker Rümelin <volker.ruemelin@googlemail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bcf3a2953d36bbfb9bd44ccb3db0897d935cc485 upstream.
The kernel may fail to boot or devices may fail to come up when
initializing iscsi_tcp devices starting with Linux 5.8.
Commit a79af8a64d39 ("[SCSI] iscsi_tcp: use iscsi_conn_get_addr_param
libiscsi function") introduced getpeername() within the session spinlock.
Commit 1b66d253610c ("bpf: Add get{peer, sock}name attach types for
sock_addr") introduced BPF_CGROUP_RUN_SA_PROG_LOCK() within getpeername(),
which acquires a mutex and when used from iscsi_tcp devices can now lead to
"BUG: scheduling while atomic:" and subsequent damage.
Ensure that the spinlock is released before calling getpeername() or
getsockname(). sock_hold() and sock_put() are used to ensure that the
socket reference is preserved until after the getpeername() or
getsockname() complete.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1877345
Link: https://lkml.org/lkml/2020/7/28/1085
Link: https://lkml.org/lkml/2020/8/31/459
Link: https://lore.kernel.org/r/20200928043329.606781-1-mark.mielke@gmail.com
Fixes: a79af8a64d39 ("[SCSI] iscsi_tcp: use iscsi_conn_get_addr_param libiscsi function")
Fixes: 1b66d253610c ("bpf: Add get{peer, sock}name attach types for sock_addr")
Cc: stable@vger.kernel.org
Reported-by: Marc Dionne <marc.c.dionne@gmail.com>
Tested-by: Marc Dionne <marc.c.dionne@gmail.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Mark Mielke <mark.mielke@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b02cf0c4736c65c6667f396efaae6b5521e82abf upstream.
The fixed divider the emac_ptp_free_clk should be 2, not 4.
Fixes: 07afb8db7340 ("clk: socfpga: stratix10: add clock driver for
Stratix10 platform")
Cc: stable@vger.kernel.org
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20200831202657.8224-1-dinguyen@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0212a0483b0a36cc94cfab882b3edbb41fcfe1cd upstream.
BPLL clock must not be disabled because it is needed for proper DRAM
operation. This is normally handled by respective memory devfreq driver,
but when that driver is not yet probed or its probe has been deferred
the clock might get disabled what causes board hang. Fix this by calling
clk_prepare_enable() directly from the clock provider driver.
Cc: stable@vger.kernel.org
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200807133143.22748-1-m.szyprowski@samsung.com
Fixes: 6e7674c3c6df ("memory: Add DMC driver for Exynos5422")
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d25e8fdebdad84219b498873300b7f11dd915b88 upstream.
The original commit appears to have the logic reversed in
amd_fch_gpio_get_direction. Also confirmed by observing the value of
"direction" in the sys tree.
Signed-off-by: Ed Wildgoose <lists@wildgooses.com>
Fixes: e09d168f13f0 ("gpio: AMD G-Series PCH gpio driver")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 214b0e1ad01abf4c1f6d8d28fa096bf167e47cef upstream.
The offset of regmap is incorrect, j * 8 is move to the
wrong register.
for example:
asume i = 0, j = 1. we want to set KPY5 as interrupt
falling edge mode, regmap[0][1] should be TC3589x_GPIOIBE1 0xcd
but, regmap[i] + j * 8 = TC3589x_GPIOIBE0 + 8 ,point to 0xd4,
this is TC3589x_GPIOIE2 not TC3589x_GPIOIBE1.
Fixes: d88b25be3584 ("gpio: Add TC35892 GPIO driver")
Cc: Cc: stable@vger.kernel.org
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1b02d9e770cd7087f34c743f85ccf5ea8372b047 upstream.
If the module init function fails after creating the debugs directory,
it's never removed. Add proper cleanup calls to avoid this resource
leak.
Fixes: 9202ba2397d1 ("gpio: mockup: implement event injecting over debugfs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 45ccf6556720293323c20cda717756014ff63007 upstream.
The gpio-siox driver uses handle_nested_irq() to implement its
interrupt support. This is only capable of handling threaded irq
actions. For a hardirq action it triggers a NULL pointer oops.
(It calls action->thread_fn which is NULL then.)
Prevent registration of a hardirq action by setting
gpio_irq_chip::threaded to true.
Cc: u.kleine-koenig@pengutronix.de
Fixes: be8c8facc707 ("gpio: new driver to work with a 8x12 siox")
Cc: stable@vger.kernel.org
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3fce39601a1a34d940cf62858ee01ed9dac5d459 upstream.
Commit 88b7381a939d ("USB: Select better matching USB drivers when
available") inadvertently broke usbip functionality. The commit in
question allows USB device drivers to be explicitly matched with
USB devices via the use of driver-provided identifier tables and
match functions, which is useful for a specialised device driver
to be chosen for a device that can also be handled by another,
more generic, device driver.
Prior, the USB device section of usb_device_match() had an
unconditional "return 1" statement, which allowed user-space to bind
USB devices to the usbip_host device driver, if desired. However,
the aforementioned commit changed the default/fallback return
value to zero. This breaks device drivers such as usbip_host, so
this commit restores the legacy behaviour, but only if a device
driver does not have an id_table and a match() function.
In addition, if usb_device_match is called for a device driver
and device pair where the device does not match the id_table of the
device driver in question, then the device driver will be disqualified
for the device. This allows avoiding the default case of "return 1",
which prevents undesirable probe() calls to a driver even though
its id_table did not match the device.
Finally, this commit changes the specialised-driver-to-generic-driver
transition code so that when a device driver returns -ENODEV, a more
generic device driver is only considered if the current device driver
does not have an id_table and a match() function. This ensures that
"generic" drivers such as usbip_host will not be considered specialised
device drivers and will not cause the device to be locked in to the
generic device driver, when a more specialised device driver could be
tried.
All of these changes restore usbip functionality without regressions,
ensure that the specialised/generic device driver selection logic works
as expected with the usb and apple-mfi-fastcharge drivers, and do not
negatively affect the use of devices provided by dummy_hcd.
Fixes: 88b7381a939d ("USB: Select better matching USB drivers when available")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <syzkaller@googlegroups.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-5-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4df30e7603432704380b12fe40a604ee7f66746d upstream.
This commit resolves a minor bug in the selection/discovery of more
specific USB device drivers for devices that are currently bound to
generic USB device drivers.
The bug is related to the way a candidate USB device driver is
compared against the generic USB device driver. The code in
is_dev_usb_generic_driver() assumes that the device driver in question
is a USB device driver by calling to_usb_device_driver(dev->driver)
to downcast; however I have observed that this assumption is not always
true, through code instrumentation.
This commit avoids the incorrect downcast altogether by comparing
the USB device's driver (i.e., dev->driver) to the generic USB
device driver directly. This method was suggested by Alan Stern.
This bug was found while investigating Andrey Konovalov's report
indicating usbip device driver misbehaviour with the recently merged
generic USB device driver selection feature. The report is linked
below.
Fixes: d5643d2249b2 ("USB: Fix device driver race")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: <syzkaller@googlegroups.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-4-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aea850cd35ae3d266fe6f93fb9edb25e4a555230 upstream.
This commit resolves a bug in the selection/discovery of more
specific USB device drivers for devices that are currently bound to
generic USB device drivers.
The bug is in the logic that determines whether a device currently
bound to a generic USB device driver should be re-probed by a
more specific USB device driver or not. The code in
__usb_bus_reprobe_drivers() used to have the following lines:
if (usb_device_match_id(udev, new_udriver->id_table) == NULL &&
(!new_udriver->match || new_udriver->match(udev) != 0))
return 0;
ret = device_reprobe(dev);
As the reader will notice, the code checks whether the USB device in
consideration matches the identifier table (id_table) of a specific
USB device_driver (new_udriver), followed by a similar check, but this
time with the USB device driver's match function. However, the match
function's return value is not checked correctly. When match() returns
zero, it means that the specific USB device driver is *not* applicable
to the USB device in question, but the code then goes on to reprobe the
device with the new USB device driver under consideration. All this to
say, the logic is inverted.
This bug was found by code inspection and instrumentation while
investigating the root cause of the issue reported by Andrey Konovalov,
where usbip took over syzkaller's virtual USB devices in an undesired
manner. The report is linked below.
Fixes: d5643d2249b2 ("USB: Fix device driver race")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: <syzkaller@googlegroups.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-3-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d6407613c1e2ef90213dee388aa16b6e1bd08cbc upstream.
This commit reverts commit 7a2f2974f265 ("usbip: Implement a match
function to fix usbip").
In summary, commit d5643d2249b2 ("USB: Fix device driver race")
inadvertently broke usbip functionality, which I resolved in an incorrect
manner by introducing a match function to usbip, usbip_match(), that
unconditionally returns true.
However, the usbip_match function, as is, causes usbip to take over
virtual devices used by syzkaller for USB fuzzing, which is a regression
reported by Andrey Konovalov.
Furthermore, in conjunction with the fix of another bug, handled by another
patch titled "usbcore/driver: Fix specific driver selection" in this patch
set, the usbip_match function causes unexpected USB subsystem behaviour
when the usbip_host driver is loaded. The unexpected behaviour can be
qualified as follows:
- If commit 41160802ab8e ("USB: Simplify USB ID table match") is included
in the kernel, then all USB devices are bound to the usbip_host
driver, which appears to the user as if all USB devices were
disconnected.
- If the same commit (41160802ab8e) is not in the kernel (as is the case
with v5.8.10) then all USB devices are re-probed and re-bound to their
original device drivers, which appears to the user as a disconnection
and re-connection of USB devices.
Please note that this commit will make usbip non-operational again,
until yet another patch in this patch set is merged, titled
"usbcore/driver: Accommodate usbip".
Cc: <stable@vger.kernel.org> # 5.8: 41160802ab8e: USB: Simplify USB ID table match
Cc: <stable@vger.kernel.org> # 5.8
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <syzkaller@googlegroups.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-2-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|