| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Packet Level Co-Running is a BT Coex feature which is
supported on certain devices only, hence the need for
a TLV flag for it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
We shouldn't call iwl_mvm_d3_disconnect_iter() on the running
interfaces when we are woken up due to net-detect, because it doesn't
make sense. Additionally, this seems to set the
IEEE80211_SDATA_DISCONNECT_RESUME flag that will cause a disconnection
on the next resume (if a normal WoWLAN is used).
To solve this, skip the iteration loop when net-detect is set.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reported-by: Samuel Tan <samueltan@chromium.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The new API slightly changes the layout of the version of
the firmware - prepare for that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Report the average beacon signal and the number of received beacons as
measured by the firmware.
Since the firmware just counts, and doesn't reset the counter at all,
clear it in the firmware whenever we associate. However, accumulate it
over firmware restart.
Since clearing the statistics in the firmware will also clear the ones
for the radio statistics, add those to the accumulator when cleared.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Due to HW bug in the DBGC when driver want to stop the dbg recording it
should wait 100us before collecting the data instead of write 0 to
DBGC_OUT_CTRL.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The legacy scan API is deprecated and not used anymore with 10 and
higher firmware versions. Since we deprecated firmware version 9, we
can remove a whole lot of unused code.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This firmware is not supported anymore. Stop loading this firmware.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Export the radio statistics from the statistics v10 API (if the
firmware also has the capability to fill these statistics) using
the global survey data facility.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
New firmware versions will report statistics using a new version 10
of the API, instead of the current version 8. Add support for this.
This enables getting beacon and radio statistics.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This allows to use the firmware debugging system even when
the configuration values are set hard coded in the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Cleanup unused code.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The shared antenna should be forbidden to use only if there's
high BT activity. Comparing to BT_OFF was effectively causing
us to always forbid using the shared antenna for SISO. This
leads to degraded performance in scenarios where the shared
antenna would have better performance.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Add this to the info printed when reading rate_scale_table.
Useful for debugging.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
ss_force is a debugging option to force a certain single stream
tx mode. It's not useful if it gets reset after tx idle. Fix that.
While at it also make sure any code touching ss_force will only
get compiled if debugfs support is configured.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Newer devices have more PAPD channel groups.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
When a TDLS station is being drained its Tx queues are still in use. Don't
allocate them to a different station in the meantime.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Due to issues with Miracast adapters MIMO reception disable
use of MIMO when for low latency P2P traffic.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Once the FW supports autonomous decision between STBC/BFER/SISO
we no longer set the STBC bit and ANT_AB in the rate table.
However the FW rate in the tx response will have the STBC
or BFER bit set and the antennas set to ANT_AB in case these
were chosen by it. This will cause us to discard any such
response as unmatching the current LQ table and thus break
the rs search cycle completely.
Fix this by relaxing the rate matching in case we're working
with the new API and STBC/BFER are used.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The check to avoid the shared antenna was passed the wrong
antenna parameter. It should have checked whether the antenna of
the next column we're considering is allowed and instead it was
passed the current antenna.
This could lead to a wrong choice of the next column in the rs
algorithm and non optimal performance.
Fixes: commit 219fb66b49fac64bb ("iwlwifi: mvm: rs - don't use the shared antenna when BT load is high")
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
For the STA interface, track 'privacy'.
Refactor safety checks to:
- always print connection params
- always check IE size validity
- require RSN IE for secure connection
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Make this field to track privacy attribute for all interface types
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
On some platforms get_cycles() implemented to allways return 0.
On such platforms "Division by zero" bug was triggered.
Signed-off-by: Boris Sorochkin <boriss@codeaurora.org>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Change threshold to be variable debugfs entry from hard-coded 0.
Default threshold value is 16 descriptors because HW is capable
of fetching up to 16 descriptors at once.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Mark expected branches using likely()/unlikely().
Do it on high performance route - data path and interrupts
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In the old hardware, bug existed that caused DA and SA for every
Rx packet to be swapped in the AP mode.
New hardware has fix for this bug. Enable this fix in the
hardware.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Hardware older than Sparrow B0 obsolete.
There is no WiFi product that uses this hardware.
Recent firmware does not support it either.
Remove driver support.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Introduce boot loader. Instead of the operational firmware,
very small boot loader is burned to the on-board flash. Boot loader
initializes hardware upon reset, and prepares for low power mode.
Boot loader reports MAC address and detects radio chip connected.
Driver loads firmware only when bringing up interface. All information
required to set up network interface, most important is MAC address,
reported by the boot loader
The firmware composed of 2 files:
- wil6210.fw - firmware itself (compiled code + data)
- wil6210.board - board file (various board and radio dependent
calibrations and parameters)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Commit 84b313b35f8158d7 ("mwifiex: make tx packet 64 byte DMA aligned")
induced payload offset issue for USB interface.
There is no USB interface header for tx packets, so there's no need to
pull interface length while processing tx skb.
This patch fixes this issue.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch adds support for DMA alignment of sk_buffs
allocated for RX.
Patch also adds support to modify skb allocation flags.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
FW crash has been observed while running iperf TX with SD8887
devices. This is because of invalid TX buffer setting. SD8887
supports 2K buffer sizes. This patch fixes this issue.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch changes datatypes for device capability flags to bool.
Patch also aggregates these variables at single place.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch fixes a crash which was happening because of RX of
management frames on uninitialzed interface. Now we drop management
frames for interfaces where cfg80211 has not registered any management
subtype reception or interface has no NL80211 iftype set.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch handles a corner case where TX packet would remain in
driver queue till next packet comes in.
Here is sequence:
1. TX packet is queued via hard_start_xmit and main_work is queued
2. SDIO interrupt comes in which directly call mwifiex_main_process.
This starts executing main superloop.
3. Now work from step1 is scheduled but at first check itself it sees
mwifiex_processing is set and exits.
4. Now if superloop from step2 has passed TX processing part of superloop
this packet would remain in queue until next packet/command/SDIO interrupt
arrives and queues main_work.
This patch fixes this corner case by defining more_task flag which is set when
mwifiex_processing is found to be true. At end of superloop we again check if
more_task flag is set and if set, execute superloop again.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Debugfs_remove will check for error or NULL for us, so it is not
necessary to do this here.
Signed-off-by: Bas Peters <baspeters93@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Delete SET_USB_STOP macro and rtl_usb_deinit because
those are called twice in USB de-initialize routine.
Add some de-initialize workqueue function in USB disconnect routine.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This device is a dongle made by Philips to enhance their TVs with wireless capabilities,
but works flawlessly on any upstream kernel, provided that the ath9k_htc module is attached to it.
It's correctly recognized by lsusb as "0471:209e Philips (or NXP) PTA01 Wireless Adapter" and the
patch has been tested on real hardware.
Signed-off-by: Leon Nardella <leon.nardella@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
All hw driver components in the rtlwifi driver, except for the
rtl8192de component has this bug. They would clear BE bit in the
ACM_CTRL register instead of the VO bit when processing the VO queue.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In some rare circumstances the escan protection timer can expire
before the setup completed (due to long timeouts on IOCTL). This
patch avoids this situation by setting the timer after the setup
completed correctly.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The SDIO watchdog will put the device in sleep mode when there is
no activity for some time and nothing to do anymore. This check
is incomplete and should also check if there is a control frame
to transmit.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Borrowed the idea of the PM freezer to make sdio suspend wait for
watchdog and DPC thread to freeze at a safe point in their thread
routine. The suspend takes 20-25 msec.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Make the revision info visible in debugfs. The new debugfs
file is named 'revinfo'.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When a key is set or cleared with an unsupported key index then
brcmfmac will print an error. With most wpa_supplicants this is
happening a lot. The error print is confusing and not needed.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Changing the SDIO state of the driver involves changing the bus
interface state. Adding a helper function makes sure that knowledge
is in one place.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
alloc_workqueue() has string format formation ability e.g. wqname%ifname
will be treated as wqnameifname. Use this and remove string operations
while defining strings for workqueue names.
Reported-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
the if/elseif/else is exhaustive - there is no 4th case given the
rssi_ctrl_mask = RADIO_2055_NBRSSI_SEL | RADIO_2055_WBRSSI_G1_SEL |
RADIO_2055_WBRSSI_G2_SEL;
so this unreachable else case (dead code) can be dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When coming out of WoW sleep, check and restart
timers based on TSF2.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The events for patterns 8..15 need to be
cleared on wakeup.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Handle the user-configured patterns in the range 8..15
when waking up and update wow_status correctly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The power save state of MCI has to be disabled
when enabling WoW sleep, check this properly.
ar9003_mci_state() doesn't handle MCI_STATE_GET_WLAN_PS_STATE
right now, but this will be done later when proper
support for MCI/PS is added.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
