| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Spectrum tunnels do not default to ttl of "inherit" like the Linux ones
do. Configure TIGCR on router init so that the TTL of tunnel packets is
copied from the overlay packets.
Fixes: ee954d1a91b2 ("mlxsw: spectrum_router: Support GRE tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TIGCR register is used for setting up the IPinIP Tunnel
configuration.
Fixes: ee954d1a91b2 ("mlxsw: spectrum_router: Support GRE tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
refresh_rate was not initialized when program
display gap.
this patch can fix vce ring test failed
when do S3 on Polaris10.
bug: https://bugs.freedesktop.org/show_bug.cgi?id=103102
bug: https://bugzilla.kernel.org/show_bug.cgi?id=196615
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fix from Vinod Koul:
"Late fix for altera driver which fixes the locking in driver"
* tag 'dmaengine-fix-4.14-rc6' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: altera: Use IRQ-safe spinlock calls in the error paths as well
|
|
The TSI channel, which is usually used for touchscreen support, but can
be used as 4 general purpose ADCs. When used as a touchscreen interface
the touchscreen driver switches the device into 1ms sampling mode (rather
than the default 10ms economy mode) as recommended by the manufacturer.
When using the TSI channels as a general purpose ADC we are currently not
doing this and testing suggests that this can result in ADC timeouts:
[ 5827.198289] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5827.728293] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5993.808335] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5994.328441] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5994.848291] da9052 spi2.0: timeout waiting for ADC conversion interrupt
Switching to the 1ms timing resolves this issue.
Fixes: 4f16cab19a3d5 ("hwmon: da9052: Add support for TSI channel")
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Default Tx rates cause very long ISR delays on Tx.
0xff is 510us delay, giving only ~ 2000 interrupts per seconds for
Tx rings cleanup. With these settings udp tx rate was never higher than
~800Mbps on a single stream. Changing min delay to 0xF makes it
way better with ~6Gbps
TCP stream performance is almost unaffected by this change, since LSO
optimizations play important role.
CPU load is affected insignificantly by this change.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Aquantia NIC allows both TX and RX interrupt throttle rate (ITR)
management, but this was used in a very limited way via predefined
values. This patch allows to setup ITR default values via module
command line arguments and via standard ethtool coalescing settings.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
That may lead to mmio resource leakage.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no much practical use from having MSIX vectors more that number
of cpus, thus cap this first with preconfigured limit, then with number
of cpus online.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When doing ifconfig down/up, driver did not reported carrier_off neither
in nic_stop nor in nic_start. That caused link to be visible as "up"
during couple of seconds immediately after "ifconfig up".
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Queue stat strings are cleaned up, duplicate stat name strings removed,
queue restarts counter added
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Internal statistics system on chip never gets reset until hardware
reboot. This is quite inconvenient in terms of ethtool statistics usage.
This patch implements incremental statistics update inside of
service callback.
Upon nic initialization, first request is done to fetch
initial stat data, current collected stat data gets cleared.
Internal statistics mailbox readout is improved to save space and
increase readability
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't access next->data in kernel debug message when the
next buffer is null.
Acked-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Sherry Yang <sherryy@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use binder_alloc struct's mm_struct rather than getting
a reference to the mm struct through get_task_mm to
avoid a potential deadlock between lru lock, task lock and
dentry lock, since a thread can be holding the task lock
and the dentry lock while trying to acquire the lru lock.
Acked-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Sherry Yang <sherryy@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On big-endian machines, functions converting between tunnel ID
and VNI use the three LSBs of tunnel ID storage to map VNI.
The comparison function eq_tun_id_and_vni(), on the other hand,
attempted to map the VNI from the three MSBs. Fix it by using
the same check implemented on LE, which maps VNI from the three
LSBs of tunnel ID.
Fixes: 2e0b26e10352 ("geneve: Optimize geneve device lookup.")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2017-10-19
this is a pull request of 11 patches for the upcoming 4.14 release.
There are 6 patches by ZHU Yi for the flexcan driver, that work around
the CAN error handling state transition problems found in various
incarnations of the flexcan IP core.
The patch by Colin Ian King fixes a potential NULL pointer deref in the
CAN broad cast manager (bcm). One patch by me replaces a direct deref of a RCU
protected pointer by rcu_access_pointer. My second patch adds missing
OOM error handling in af_can. A patch by Stefan Mätje for the esd_usb2
driver fixes the dlc in received RTR frames. And the last patch is by
Wolfgang Grandegger, it fixes a busy loop in the gs_usb driver in case
it runs out of TX contexts.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here is another set of bugfixes for ARM SoCs, mostly harmless:
- a boot regression fix on ux500
- PCIe interrupts on NXP i.MX7 and on Marvell Armada 7K/8K were wired
up wrong, in different ways
- Armada XP support for large memory never worked
- the socfpga reset controller now builds on 64-bit
- minor device tree corrections on gemini, mvebu, r-pi 3, rockchip
and at91"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ux500: Fix regression while init PM domains
ARM: dts: fix PCLK name on Gemini and MOXA ART
arm64: dts: rockchip: fix typo in iommu nodes
arm64: dts: rockchip: correct vqmmc voltage for rk3399 platforms
ARM: dts: imx7d: Invert legacy PCI irq mapping
bus: mbus: fix window size calculation for 4GB windows
ARM: dts: at91: sama5d2: add ADC hw trigger edge type
ARM: dts: at91: sama5d2_xplained: enable ADTRG pin
ARM: dts: at91: at91-sama5d27_som1: fix PHY ID
ARM: dts: bcm283x: Fix console path on RPi3
reset: socfpga: fix for 64-bit compilation
ARM: dts: Fix I2C repeated start issue on Armada-38x
arm64: dts: marvell: fix interrupt-map property for Armada CP110 PCIe controller
arm64: dts: salvator-common: add 12V regulator to backlight
ARM: dts: sun6i: Fix endpoint IDs in second display pipeline
arm64: allwinner: a64: pine64: Use dcdc1 regulator for mmc0
|
|
Pull NVMe fixes from Christoph:
"Below are two regression fixes each for RDMA and FC, and a fix for a
SQHD update race in the target."
|
|
Without the patch, vmbus_hvsock_device_unregister() can destroy the device
prematurely when close() is called, and can cause NULl dereferencing or
potential data loss (the last portion of the data stream may be dropped
prematurely).
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The interrupt handler mfgpt_tick() is not robust versus spurious interrupts
which happen before the clock event device is registered and fully
initialized.
The reason is that the safe guard against spurious interrupts solely checks
for the clockevents shutdown state, but lacks a check for detached
state. If the interrupt hits while the device is in detached state it
passes the safe guard and dereferences the event handler call back which is
NULL.
Add the missing state check.
Fixes: 8f9327cbb6e8 ("clockevents/drivers/cs5535: Migrate to new 'set-state' interface")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20171020093103.3317F6004D@linux.fjfi.cvut.cz
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fix from Juergen Gross:
"A fix for the Xen pv network drivers (frontend and backend) avoiding
the network connection to become unusable due to an illegal MTU"
* tag 'for-linus-4.14c-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen-netfront, xen-netback: Use correct minimum MTU values
|
|
Because we're not guaranteed that subsequent calls
to poll() will have a poll_table_struct parameter
with _qproc set. When _qproc is not set, poll_wait()
is a noop, and we won't be woken up correctly.
Signed-off-by: Martijn Coenen <maco@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fix from Ulf Hansson:
"sdhci-pci: Fix default d3_retune for Intel host controllers"
* tag 'mmc-v4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-pci: Fix default d3_retune for Intel host controllers
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Standard fixes pull for rc6: one regression fix for amdgpu, a bunch of
nouveau fixes that I'd missed a pull req for from Ben last week, some
exynos regression fixes, and a few fixes for i915"
* tag 'drm-fixes-for-v4.14-rc6' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/fbcon: fix oops without fbdev emulation
Revert "drm/amdgpu: discard commands of killed processes"
drm/i915: Use a mask when applying WaProgramL3SqcReg1Default
drm/i915: Report -EFAULT before pwrite fast path into shmemfs
drm/i915/cnl: Fix PLL initialization for HDMI.
drm/i915/cnl: Fix PLL mapping.
drm/i915: Use bdw_ddi_translations_fdi for Broadwell
drm/i915: Fix eviction when the GGTT is idle but full
drm/i915/gvt: Fix GPU hang after reusing vGPU instance across different guest OS
drm/exynos: Clear drvdata after component unbind
drm/exynos: Fix potential NULL pointer dereference in suspend/resume paths
drm/nouveau/kms/nv50: fix oops during DP IRQ handling on non-MST boards
drm/nouveau/bsp/g92: disable by default
drm/nouveau/mmu: flush tlbs before deleting page tables
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"A couple of bugfixes for I2C drivers.
Because the changes for the piix4 driver are larger than usual, the
patches have been in linux-next for more than a week with no reports
coming in. The rest is usual stuff"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: omap: Fix error handling for clk_get()
i2c: piix4: Disable completely the IMC during SMBUS_BLOCK_DATA
i2c: piix4: Fix SMBus port selection for AMD Family 17h chips
i2c: imx: fix misleading bus recovery debug message
i2c: imx: use IRQF_SHARED mode to request IRQ
i2c: ismt: Separate I2C block read from SMBus block read
|
|
The patch edf10919 [dmaengine: altera: fix spinlock usage] missed to
change 2 occurrences of spin_unlock_bh() to spin_unlock_irqrestore().
This patch fixes this by moving to the IRQ-safe call in the error
paths as well.
Fixes: edf10919 (dmaengine: altera: fix spinlock usage)
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Sylvain Lesne <lesne@alse-fr.com>
[add fixes tag and fix typo in log]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Before trying to use CDC union descriptor, try to validate whether that it
is sane by checking that intf->altsetting->extra is big enough and that
descriptor bLength is not too big and not too small.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Introduce a device table used for blacklisting devices. We currently
blacklist the motion sensor subdevice of THQ Udraw and Sony ds3/ds4.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
[dtor: siwtched to blacklist built on input_device_id and using
input_match_device_id()]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Let's allow matching input devices on their property bits, both in-kernel
and when generating module aliases.
Tested-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Factor out and export input_match_device_id() so that modules may use it.
It will be needed by joydev to blacklist accelerometers in composite
devices.
Tested-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The Goodix panel triggers an interrupt on touch events. However, its
registers will contain the valid values a short time after the
interrupt, and not when it's raised. At that moment, the 'buffer status'
bit is set.
Previously, if the 'buffer status' bit was not set when the registers
were read, the data was discarded and no input event was emitted,
causing "finger down" or "finger up" events to be missed sometimes.
This went unnoticed until v4.9, as the DesignWare I2C driver commonly
used with this driver had enough latency for that bug to never trigger
until commit 2702ea7dbec5 ("i2c: designware: wait for disable/enable only
if necessary").
Now, in the IRQ handler we will poll (with a timeout) the 'buffer status'
bit and process the data of the panel as soon as this bit gets set.
Note that the Goodix panel will send a few spurious interrupts after the
'finger up' event, in which the 'buffer status' bit will never be set.
Cc: Bastien Nocera <hadess@hadess.net>
Cc: russianneuromancer@ya.ru
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
[hdegoede@redhat.com: Change poll loop to use jiffies,
add comment about typical poll time]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[dtor: rearranged control flow a bit to avoid explicit goto and double
check]
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Now that we have a platform_device_id table and multiple supported ids
we should be using MODULE_DEVICE_TABLE instead of MODULE_ALIAS.
This fixes a regression on Bay and Cherry Trail devices, where the power
button is now enumerated as an "axp221-pek" and it was impossible to
wakeup these devices from suspend since the module did not load.
Fixes: c3cc94470bd3 ("Input: axp20x-pek - add support for AXP221 PEK")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Currently, enabling keypad interrupts is one of the first operations
done on the keypad, even before the interrupt is requested, so there is
a small time window where the keypad can fire interrupts but the driver
is not yet ready to handle them. It's fine for level interrupts because
they will be handled anyway, but not so much for edge ones.
This commit modifies and moves the function in charge of configuring the
keypad. Enabling interrupts is now the last thing done on the keypad,
and after the interrupt has been requested by the driver.
Writing to the config register was also used to determine if the device
was indeed present on the bus or not, this has been replaced by reading
the lock/event count register to keep the same functionality.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
into fixes
Pull "Reset controller fixes for v4.14" from Philipp Zabel:
Fix SoCFPGA reset controller for 64-bit systems. This patch removes the
assumption that BITS_PER_LONG is 32, which is not the case on Stratix10.
* tag 'reset-fixes-for-4.14-2' of git://git.pengutronix.de/git/pza/linux:
reset: socfpga: fix for 64-bit compilation
|
|
Pull "mvebu fixes for 4.14 (part 2)" from Gregory CLEMENT
Two device tree related fixes:
- One on Armada 38x using a other compatible string for I2C in order
to cover an errata.
- One for Armada 7K/8K fixing a typo on interrupt-map property for
PCIe leading to fail PME and AER root port service initialization
And the last one for the mbus fixing the window size calculation when
it exceed 32bits
* tag 'mvebu-fixes-4.14-2' of git://git.infradead.org/linux-mvebu:
bus: mbus: fix window size calculation for 4GB windows
ARM: dts: Fix I2C repeated start issue on Armada-38x
arm64: dts: marvell: fix interrupt-map property for Armada CP110 PCIe controller
|
|
We should make sure to escelate allocation failures to prevent a
use-after-free in nvmf_create_ctrl.
Fixes: b28a308ee777 ("nvme-rdma: move tagset allocation to a dedicated routine")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The fact that we free the async event buffer in
nvme_rdma_destroy_admin_queue can cause us to free it
more than once because this happens in every reconnect
attempt since commit 31fdf1840170. we rely on the queue
state flags DELETING to avoid this for other resources.
A more complete fix is to not destroy the admin/io queues
unconditionally on every reconnect attempt, but its a bit
more extensive and will go in the next release.
Fixes: 31fdf1840170 ("nvme-rdma: reuse configure/destroy_admin_queue")
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
ethtool ena_get_channels() expose the max number of queues as the max
number of queues ENA supports (128 queues) and not the actual number
of created queues.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This failure is rare and only found on testing where deliberately fail
devm_ioremap()
[ 451.170464] ena 0000:04:00.0: failed to remap regs bar
451.170549] Workqueue: pciehp-1 pciehp_power_thread
[ 451.170551] task: ffff88085a5f2d00 task.stack: ffffc9000756c000
[ 451.170552] RIP: 0010:devm_iounmap+0x2d/0x40
[ 451.170553] RSP: 0018:ffffc9000756fac0 EFLAGS: 00010282
[ 451.170554] RAX: 00000000fffffffe RBX: 0000000000000000 RCX:
0000000000000000
[ 451.170555] RDX: ffffffff813a7e00 RSI: 0000000000000282 RDI:
0000000000000282
[ 451.170556] RBP: ffffc9000756fac8 R08: 00000000fffffffe R09:
00000000000009b7
[ 451.170557] R10: 0000000000000005 R11: 00000000000009b6 R12:
ffff880856c9d0a0
[ 451.170558] R13: ffffc9000f5c90c0 R14: ffff880856c9d0a0 R15:
0000000000000028
[ 451.170559] FS: 0000000000000000(0000) GS:ffff88085f400000(0000)
knlGS:0000000000000000
[ 451.170560] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 451.170561] CR2: 00007f169038b000 CR3: 0000000001c09000 CR4:
00000000003406f0
[ 451.170562] DR0: 0000000000000000 DR1: 0000000000000000 DR2:
0000000000000000
[ 451.170562] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7:
0000000000000400
[ 451.170563] Call Trace:
[ 451.170572] ena_release_bars.isra.48+0x34/0x60 [ena]
[ 451.170574] ena_probe+0x144/0xd90 [ena]
[ 451.170579] ? ida_simple_get+0x98/0x100
[ 451.170585] ? kernfs_next_descendant_post+0x40/0x50
[ 451.170591] local_pci_probe+0x45/0xa0
[ 451.170592] pci_device_probe+0x157/0x180
[ 451.170599] driver_probe_device+0x2a8/0x460
[ 451.170600] __device_attach_driver+0x7e/0xe0
[ 451.170602] ? driver_allows_async_probing+0x30/0x30
[ 451.170603] bus_for_each_drv+0x68/0xb0
[ 451.170605] __device_attach+0xdd/0x160
[ 451.170607] device_attach+0x10/0x20
[ 451.170610] pci_bus_add_device+0x4f/0xa0
[ 451.170611] pci_bus_add_devices+0x39/0x70
[ 451.170613] pciehp_configure_device+0x96/0x120
[ 451.170614] pciehp_enable_slot+0x1b3/0x290
[ 451.170616] pciehp_power_thread+0x3b/0xb0
[ 451.170622] process_one_work+0x149/0x360
[ 451.170623] worker_thread+0x4d/0x3c0
[ 451.170626] kthread+0x109/0x140
[ 451.170627] ? rescuer_thread+0x380/0x380
[ 451.170628] ? kthread_park+0x60/0x60
[ 451.170632] ret_from_fork+0x25/0x30
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Decrease log level of checksum errors as these messages can be
triggered remotely by bad packets.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If sending messages with no cable connected, it quickly happens that
there is no more TX context available. Then "gs_can_start_xmit()"
returns with "NETDEV_TX_BUSY" and the upper layer does retry
immediately keeping the CPU busy. To fix that issue, I moved
"atomic_dec(&dev->active_tx_urbs)" from "gs_usb_xmit_callback()" to
the TX done handling in "gs_usb_receive_bulk_callback()". Renaming
"active_tx_urbs" to "active_tx_contexts" and moving it into
"gs_[alloc|free]_tx_context()" would also make sense.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The dlc member of the struct rx_msg contains also the ESD_RTR flag to
mark received RTR frames. Without the fix the can_dlc value for received
RTR frames would always be set to 8 by get_can_dlc() instead of the
received value.
Fixes: 96d8e90382dc ("can: Add driver for esd CAN-USB/2 device")
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Enable FLEXCAN_QUIRK_BROKEN_WERR_STATE and
FLEXCAN_QUIRK_BROKEN_PERR_STATE for p1010 to report correct state
transitions.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Enable FLEXCAN_QUIRK_BROKEN_PERR_STATE for i.MX28 to report correct
state transitions, especially to error passive.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Enable FLEXCAN_QUIRK_BROKEN_PERR_STATE for i.MX6 to report correct state
transitions.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add FLEXCAN_QUIRK_BROKEN_PERR_STATE for better description of the
missing error passive interrupt quirk.
Error interrupt flooding may happen if the broken error state quirk fix
is enabled. For example, in case there is singled out node on the bus
and the node sends a frame, then error interrupt flooding happens and
will not stop because the node cannot go to bus off. The flooding will
stop after another node connected to the bus again.
If high bitrate configured on the low end system, then the flooding
may causes performance issue, hence, this patch mitigates this by:
1. disable error interrupt upon error passive state transition
2. re-enable error interrupt upon error warning state transition
3. disable/enable error interrupt upon error active state transition
depends on FLEXCAN_QUIRK_BROKEN_WERR_STATE
In this way, the driver is still able to report correct state
transitions without additional latency. When there are bus problems,
flooding of error interrupts is limited to the number of frames required
to change state from error warning to error passive if the core has
[TR]WRN_INT connected (FLEXCAN_QUIRK_BROKEN_WERR_STATE is not enabled),
otherwise, the flooding is limited to the number of frames required to
change state from error active to error passive.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Rename FLEXCAN_QUIRK_BROKEN_ERR_STATE to FLEXCAN_QUIRK_BROKEN_WERR_STATE
for better description of the missing [TR]WRN_INT quirk.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Update state upon any interrupt to report correct state transitions in
case the flexcan core enabled the broken error state quirk fix.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
interrupt handling was broken with conversion to using regmap caching.
cached_gpio value was updated by boolean status instead of gpio reading.
Fixes: 8f38910ba4f6 ("pinctrl: mcp23s08: switch to regmap caching")
Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Dmitry Mastykin <mastichi@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
On Asus laptop models X505BA, X505BP, X542BA and X542BP, the i2c-hid
touchpad (using a GPIO for interrupts) becomes unresponsive after a
few minutes of usage, or after placing two fingers on the touchpad,
which seems to have the effect of queuing up a large amount of input
data to be transferred.
When the touchpad is in unresponsive state, we observed that the GPIO
level-triggered interrupt is still at it's active level, however the
pinctrl-amd driver is not receiving/dispatching more interrupts at this
point.
After the initial interrupt arrives, amd_gpio_irq_mask() is called
however we then see amd_gpio_irq_handler() being called repeatedly for
the same irq; the interrupt mask is not taking effect because of the
following sequence of events:
- amd_gpio_irq_handler fires, reads and caches pin reg
- amd_gpio_irq_handler calls generic_handle_irq()
- During IRQ handling, amd_gpio_irq_mask() is called and modifies pin reg
- amd_gpio_irq_handler clears interrupt by writing cached value
The stale cached value written at the final stage undoes the masking.
Fix this by re-reading the register before clearing the interrupt.
I also spotted that the interrupt-clearing code can race against
amd_gpio_irq_mask() / amd_gpio_irq_unmask(), so add locking there.
Presumably this race was leading to the loss of interrupts.
After these changes, the touchpad appears to be working fine.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Acked-by: Shah, Nehal-bakulchandra <Nehal-Bakulchandra.shah@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
