summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2010-05-18bnx2x: avoid TX timeout when stopping deviceStanislaw Gruszka1-4/+2
When stop device call netif_carrier_off() just after disabling TX queue to avoid possibility of netdev watchdog warning and ->ndo_tx_timeout() invocation. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18bnx2: Use netif_carrier_off() to prevent timeout.Michael Chan1-9/+5
Based on original patch from Stanislaw Gruszka <sgruszka@redhat.com>. Using netif_carrier_off() is better than updating all the ->trans_start on all the tx queues. netif_carrier_off() needs to be called after bnx2_disable_int_sync() to guarantee no race conditions with the serdes timers that can modify the carrier state. If the chip or phy is reset, carrier will turn back on when we get the link interrupt. If there is no reset, we need to turn carrier back on in bnx2_netif_start(). Again, the phy_lock prevents race conditions with the serdes timers. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18bnx2: Update 5709 MIPS firmware and version to 2.0.15.Michael Chan1-3/+3
New firmware fixes a performance regression on small packets. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18bnx2: Fix register printouts during NETEV_WATCHDOG.Eddie Wai2-3/+14
Dump the correct MCP registers and add EMAC_RX_STATUS register during NETDEV_WATCHDOG for debugging. Signed-off-by: Eddie Wai <waie@broadcom.com> Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18qlcnic: mark device state failAmit Kumar Salecha1-2/+8
Device state need to be mark as FAILED, if fail to start firmware. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18qlcnic: remove unused registerAmit Kumar Salecha4-21/+0
Removing register defines which are not used by Qlgoic CNA device. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18qlcnic: fix internal loopback testSucheta Chakraborty1-0/+2
Reset/set DEV_UP bit during allocation and deallocation of resources. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18qlcnic: module param for firmware load optionAmit Kumar Salecha1-1/+8
By default fw is loaded from flash, user can change this priority using load_fw_file module param. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18qlcnic: fix rx bytes statisticsSucheta Chakraborty1-1/+1
Added lrobytes to it. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18qlcnic: change adapter name displaySucheta Chakraborty1-1/+6
Append mac address to adapter name. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18qlcnic: fix memory leaksAnirban Chakraborty2-3/+4
Fixes memory leak in error path when memory allocation for adapter data structures fails. Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18netdev: bfin_mac: check for mii_bus platform dataSonic Zhang1-0/+6
If the platform data for the mii_bus is missing, gracefully error out rather than deference NULL pointers. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18netdev: bfin_mac: handle timeouts with the MDIO registers gracefullyMike Frysinger1-19/+34
Have the low level MDIO functions pass back up timeout information so we don't waste time polling them multiple times when there is a problem, and so we don't let higher layers think the device is available when it isn't. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18netdev: bfin_mac: use promiscuous flag for promiscuous modeSonic Zhang1-1/+1
Rather than using the Receive All Frames (RAF) bit to enable promiscuous mode, use the Promiscuous (PR) bit. This lowers overhead at runtime as we let the hardware process the packets that should actually be checked. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18netdev: bfin_mac: add support for wake-on-lan magic packetsMichael Hennerich2-4/+75
Note that WOL works only in PM Suspend Standby Mode (Sleep Mode). Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18netdev: bfin_mac: clear RXCKS if hardware generated checksum is not enabledSonic Zhang1-2/+3
Otherwise we might be get a setting mismatch from a previous module or bootloader and what the driver currently expects. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18netdev: bfin_mac: deduce Ethernet FCS from hardware IP payload checksumSonic Zhang1-2/+33
IP checksum is based on 16-bit one's complement algorithm, so to deduce a value from checksum is equal to add its complement. Unfortunately, the Blackfin on-chip MAC checksum logic only works when the IP packet has a header length of 20 bytes. This is true for most IPv4 packets, but not for IPv6 packets or IPv4 packets which use header options. So only use the hardware checksum when appropriate. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Jon Kowal <jon.kowal@dspecialists.de> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18netdev: bfin_mac: invalid data cache only once for each new rx skb bufferSonic Zhang1-5/+8
The skb buffer isn't actually used until we finish transferring and pass it up to higher layers, so only invalidate the range once before we start receiving actual data. This also avoids the problem with data invalidating on Blackfin systems -- there is no invalidate-only, just invalidate+flush. So when running in writeback mode, there is the small (but not uncommon) possibility of the flush overwriting valid DMA-ed data from the cache. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18netdev: bfin_mac: handler RX status errorsPeter Meerwald1-3/+14
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net> Signed-off-by: Graf Yang <graf.yang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18netdev: bfin_mac: add support for IEEE 1588 PTPBarry Song3-1/+362
Newer on-chip MAC peripherals support IEEE 1588 PTP in the hardware, so extend the driver to support this functionality. Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18drivers/net/usb/asix.c: Fix unaligned accessesNeil Jones1-1/+33
Using this driver can cause unaligned accesses in the IP layer This has been fixed by aligning the skb data correctly using the spare room left over by the 4 byte header inserted between packets by the device. Signed-off-by: Neil Jones <NeilJay@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-18ibmveth: Add suspend/resume supportBrian King1-0/+12
Adds support for resuming from suspend for IBM virtual ethernet devices. We may have lost an interrupt over the suspend, so we just kick the interrupt handler to process anything that is outstanding. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17Merge branch 'master' of ↵David S. Miller1-1/+6
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: include/linux/if_link.h
2010-05-16qeth: synchronize configuration interfaceFrank Blaschka6-168/+242
Synchronize access to the drivers configuration interface. Also do not allow configuration changes during online/offline transition. Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-16qeth: new message if OLM limit is reachedUrsula Braun1-1/+9
z/OS may activate Optimized Latency Mode (OLM) for a connection through an OSA Express3 adapter, which reduces the number of allowed concurrent connections, if adapter is used in shared mode. Create a meaningful message, if activation of an OSA-connection fails due to an active OLM-connection on the shared OSA-adapter. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-16qeth: exploit HW TX checksummingFrank Blaschka2-26/+69
OSA supports HW TX checksumming in layer 3 mode. Enable this feature and remove software fallback used for TSO. Cleanup checksum bits to indicate OSA can do checksumming only for IPv4 TCP and UDP. Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-16net: congestion notifications are not dropped packetsEric Dumazet1-1/+1
vlan/macvlan start_xmit() can inform caller of congestion with NET_XMIT_CN return value. This doesnt mean packet was dropped. Increment normal stat counters instead of tx_dropped. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-16net: adjust handle_macvlan to pass port struct to hookJiri Pirko1-6/+2
Now there's null check here and also again in the hook. Looking at bridge bits which are simmilar, port structure is rcu_dereferenced right away in handle_bridge and passed to hook. Looks nicer. Signed-off-by: Jiri Pirko <jpirko@redhat.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-16skge: use the DMA state API instead of the pci equivalentsFUJITA Tomonori2-18/+18
This replace the PCI DMA state API (include/linux/pci-dma.h) with the DMA equivalents since the PCI DMA state API will be obsolete. No functional change. For further information about the background: http://marc.info/?l=linux-netdev&m=127037540020276&w=2 Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-16Merge branch 'master' of ↵David S. Miller10-116/+479
git://git.kernel.org/pub/scm/linux/kernel/git/inaky/wimax
2010-05-16rndis_host: Poll status channel before control channelBen Hutchings1-6/+12
Some RNDIS devices don't respond on the control channel until polled on the status channel. In particular, this was reported to be the case for the 2Wire HomePortal 1000SW. This is roughly based on a patch by John Carr <john.carr@unrouted.co.uk> which is reported to be needed for use with some Windows Mobile devices and which is currently applied by Mandriva. Reported-by: Mark Glassberg <vzeeaxwl@myfairpoint.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Tested-by: Mark Glassberg <vzeeaxwl@myfairpoint.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14Merge branch 'net-2.6' of ↵David S. Miller1-1/+6
git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
2010-05-14qlcnic: add idc debug registersSucheta Chakraborty2-0/+23
When ever driver changes the device state, it should write pci-func number and timestamp in debug registers. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14qlcnic: support quisce modeSucheta Chakraborty1-2/+26
Device can go to quiescent state, during which drivers should refrain from using the device. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14qlcnic: check device classSucheta Chakraborty3-8/+18
pci-func class can be other than ethernet in Qlogic CNA device. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14qlcnic: check IDC versionSucheta Chakraborty2-2/+19
Warn user if IDC version mismatch with different class of drivers. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14qlcnic: cleanup unused codeAmit Kumar Salecha4-61/+10
LRO ring, cut-thru mode and specific fw version are not valid to Qlogic CNA device. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14qlcnic: cleanup dma mask settingAmit Kumar Salecha2-70/+24
Device support 64 bit dma mask. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14qlcnic: fix caching window registerAmit Kumar Salecha3-18/+0
o Window register is not per pci-func, so caching can result in expected result. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14qlcnic: remove obsolete registerAmit Kumar Salecha3-16/+1
MSI_MODE, CAPABILITIES_FW and SCRATCHPAD registers are obsolete. Driver should not use them. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14qlcnic: fix context cleanupAmit Kumar Salecha1-3/+1
Before going for recovery, every pci-func should check fw state, irrespective of device state. This to avoid unnecssary sending of command for ctx destroy. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14sky2: version 1.28stephen hemminger1-1/+1
Version 1.28 Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14sky2: Avoid allocating memory in sky2_resumeMike McCormack1-15/+5
Allocating memory can fail, and since we have the memory we need in sky2_resume when sky2_suspend is called, just stop the hardware without freeing the memory it's using. This avoids the possibility of failing because we can't allocate memory in sky2_resume(), and allows sharing code with sky2_restart(). Signed-off-by: Mike McCormack <mikem@ring3k.org> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14sky2: Refactor down/up code out of sky2_restart()Mike McCormack1-7/+19
Code to bring down all sky2 interfaces and bring it up again can be reused in sky2_suspend and sky2_resume. Factor the code to bring the interfaces down into sky2_all_down and the up code into sky2_all_up. Signed-off-by: Mike McCormack <mikem@ring3k.org> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14sky2: Shut off interrupts before NAPIMike McCormack1-2/+2
Interrupts should be masked, then synchronized, and finally NAPI should be disabled. Signed-off-by: Mike McCormack <mikem@ring3k.org> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14sky2: Avoid race in sky2_change_mtuMike McCormack1-1/+1
netif_stop_queue does not ensure all in-progress transmits are complete, so use netif_tx_disable() instead. Secondly, make sure NAPI polls are disabled before stopping the tx queue, otherwise sky2_status_intr might trigger a TX queue wakeup between when we stop the queue and NAPI is disabled. Signed-off-by: Mike McCormack <mikem@ring3k.org> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14sky2: Restore multicast after restartMike McCormack1-0/+1
Multicast settings will be lost on reset, so restore them. Signed-off-by: Mike McCormack <mikem@ring3k.org> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14ixgb and e1000: Use new function for copybreak testsJoe Perches2-41/+58
There appears to be an off-by-1 defect in the maximum packet size copied when copybreak is speified in these modules. The copybreak module params are specified as: "Maximum size of packet that is copied to a new buffer on receive" The tests are changed from "< copybreak" to "<= copybreak" and moved into new static functions for readability. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14e1000: cleanup unused parametersJesse Brandeburg1-8/+0
During the cleanup pass after the removal of e1000e hardware from e1000 some parameters were missed. Remove them because it is just dead code. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14e1000: fix WARN_ON with mac-vlanJesse Brandeburg1-2/+0
When adding more than 14 mac-vlan adapters on e1000 the driver would fire a WARN_ON when adding the 15th. The WARN_ON in this case is completely un-necessary, as the code below the WARN_ON is directly handling the value the WARN_ON triggered on. CC: Jiri Pirko <jpirko@redhat.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2024-08-09 01:25:43 +0300