Age | Commit message (Collapse) | Author | Files | Lines |
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc updates from Ben Herrenschmidt:
"This is the powerpc new goodies for 3.17. The short story:
The biggest bit is Michael removing all of pre-POWER4 processor
support from the 64-bit kernel. POWER3 and rs64. This gets rid of a
ton of old cruft that has been bitrotting in a long while. It was
broken for quite a few versions already and nobody noticed. Nobody
uses those machines anymore. While at it, he cleaned up a bunch of
old dusty cabinets, getting rid of a skeletton or two.
Then, we have some base VFIO support for KVM, which allows assigning
of PCI devices to KVM guests, support for large 64-bit BARs on
"powernv" platforms, support for HMI (Hardware Management Interrupts)
on those same platforms, some sparse-vmemmap improvements (for memory
hotplug),
There is the usual batch of Freescale embedded updates (summary in the
merge commit) and fixes here or there, I think that's it for the
highlights"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (102 commits)
powerpc/eeh: Export eeh_iommu_group_to_pe()
powerpc/eeh: Add missing #ifdef CONFIG_IOMMU_API
powerpc: Reduce scariness of interrupt frames in stack traces
powerpc: start loop at section start of start in vmemmap_populated()
powerpc: implement vmemmap_free()
powerpc: implement vmemmap_remove_mapping() for BOOK3S
powerpc: implement vmemmap_list_free()
powerpc: Fail remap_4k_pfn() if PFN doesn't fit inside PTE
powerpc/book3s: Fix endianess issue for HMI handling on napping cpus.
powerpc/book3s: handle HMIs for cpus in nap mode.
powerpc/powernv: Invoke opal call to handle hmi.
powerpc/book3s: Add basic infrastructure to handle HMI in Linux.
powerpc/iommu: Fix comments with it_page_shift
powerpc/powernv: Handle compound PE in config accessors
powerpc/powernv: Handle compound PE for EEH
powerpc/powernv: Handle compound PE
powerpc/powernv: Split ioda_eeh_get_state()
powerpc/powernv: Allow to freeze PE
powerpc/powernv: Enable M64 aperatus for PHB3
powerpc/eeh: Aux PE data for error log
...
|
|
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 3.17. It contains:
- misc Cavium Octeon, BCM47xx, BCM63xx and Alchemy updates
- MIPS ptrace updates and cleanups
- various fixes that will also go to -stable
- a number of cleanups and small non-critical fixes.
- NUMA support for the Loongson 3.
- more support for MSA
- support for MAAR
- various FP enhancements and fixes"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
MIPS: jz4740: remove unnecessary null test before debugfs_remove
MIPS: Octeon: remove unnecessary null test before debugfs_remove_recursive
MIPS: ZBOOT: implement stack protector in compressed boot phase
MIPS: mipsreg: remove duplicate MIPS_CONF4_FTLBSETS_SHIFT
MIPS: Bonito64: remove a duplicate define
MIPS: Malta: initialise MAARs
MIPS: Initialise MAARs
MIPS: detect presence of MAARs
MIPS: define MAAR register accessors & bits
MIPS: mark MSA experimental
MIPS: Don't build MSA support unless it can be used
MIPS: consistently clear MSA flags when starting & copying threads
MIPS: 16 byte align MSA vector context
MIPS: disable preemption whilst initialising MSA
MIPS: ensure MSA gets disabled during boot
MIPS: fix read_msa_* & write_msa_* functions on non-MSA toolchains
MIPS: fix MSA context for tasks which don't use FP first
MIPS: init upper 64b of vector registers when MSA is first used
MIPS: save/disable MSA in lose_fpu
MIPS: preserve scalar FP CSR when switching vector context
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
"Mostly cleanups and bug-fixes, with two exceptions.
The first is lazy flushing of I/O-TLBs for PCI to improve performance,
the second is software dirty bits in the pmd for the madvise-free
implementation"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (24 commits)
s390/locking: Reenable optimistic spinning
s390/mm: implement dirty bits for large segment table entries
KVM: s390/mm: Fix page table locking vs. split pmd lock
s390/dasd: fix camel case
s390/3215: fix hanging console issue
s390/irq: improve displayed interrupt order in /proc/interrupts
s390/seccomp: fix error return for filtered system calls
s390/pci: introduce lazy IOTLB flushing for DMA unmap
dasd: fix error recovery for alias devices during format
dasd: fix list_del corruption during format
dasd: fix unresponsive device during format
dasd: use aliases for formatted devices during format
s390/pci: fix kmsg component
s390/kdump: Return NOTIFY_OK for all actions other than MEM_GOING_OFFLINE
s390/watchdog: Fix module name in Kconfig help text
s390/dasd: replace seq_printf by seq_puts
s390/dasd: replace pr_warning by pr_warn
s390/dasd: Move EXPORT_SYMBOL after function/variable
s390/dasd: remove unnecessary null test before debugfs_remove
s390/zfcp: use qdio buffer helpers
...
|
|
Merge incoming from Andrew Morton:
- Various misc things.
- arch/sh updates.
- Part of ocfs2. Review is slow.
- Slab updates.
- Most of -mm.
- printk updates.
- lib/ updates.
- checkpatch updates.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (226 commits)
checkpatch: update $declaration_macros, add uninitialized_var
checkpatch: warn on missing spaces in broken up quoted
checkpatch: fix false positives for --strict "space after cast" test
checkpatch: fix false positive MISSING_BREAK warnings with --file
checkpatch: add test for native c90 types in unusual order
checkpatch: add signed generic types
checkpatch: add short int to c variable types
checkpatch: add for_each tests to indentation and brace tests
checkpatch: fix brace style misuses of else and while
checkpatch: add --fix option for a couple OPEN_BRACE misuses
checkpatch: use the correct indentation for which()
checkpatch: add fix_insert_line and fix_delete_line helpers
checkpatch: add ability to insert and delete lines to patch/file
checkpatch: add an index variable for fixed lines
checkpatch: warn on break after goto or return with same tab indentation
checkpatch: emit a warning on file add/move/delete
checkpatch: add test for commit id formatting style in commit log
checkpatch: emit fewer kmalloc_array/kcalloc conversion warnings
checkpatch: improve "no space after cast" test
checkpatch: allow multiple const * types
...
|
|
Pull networking fixes from David Miller:
"This fixes the most immediate fallout from yesterday's networking
merge:
1) sock_tx_timestamp() must not clear the passed in tx_flags, but
rather add to them. Fix from Eric Dumazet.
2) The hyperv driver sendbuf region increase needs to be decreased
slightly to handle older backends. From KY Srinivasan.
3) Fix RCU lockdep splats in netlink diag after recent hashing
changes, from Thomas Graf.
4) The new IPV6_FLOWLABEL was given a socket option number that
overlapped with an existing IP6 tables one, breaking ip6_tables.
Fixed by Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
netlink: hold nl_sock_hash_lock during diag dump
tcp: md5: check md5 signature without socket lock
net: fix USB network driver config option.
net: reallocate new socket option number for IPV6_AUTOFLOWLABEL
vmxnet3: fix decimal printf format specifiers prefixed with 0x
net-timestamp: cumulative tcp timestamping fixes
hyperv: Adjust the size of sendbuf region to support ws2008r2
cxgb4: Fix for SR-IOV VF initialization
net-timestamp: sock_tx_timestamp() fix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree changes from Jiri Kosina:
"Summer edition of trivial tree updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: fix two typos in watchdog-api.txt
irq-gic: remove file name from heading comment
MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
scsi: mvsas: mv_sas.c: Fix for possible null pointer dereference
doc: replace "practise" with "practice" in Documentation
befs: remove check for CONFIG_BEFS_RW
scsi: doc: fix 'SCSI_NCR_SETUP_MASTER_PARITY'
drivers/usb/phy/phy.c: remove a leading space
mfd: fix comment
cpuidle: fix comment
doc: hpfall.c: fix missing null-terminate after strncpy call
usb: doc: hotplug.txt code typos
kbuild: fix comment in Makefile.modinst
SH: add proper prompt to SH_MAGIC_PANEL_R2_VERSION
ARM: msm: Remove MSM_SCM
crypto: Remove MPILIB_EXTRA
doc: CN: remove dead link, kerneltrap.org no longer works
media: update reference, kerneltrap.org no longer works
hexagon: update reference, kerneltrap.org no longer works
doc: LSM: update reference, kerneltrap.org no longer works
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
"Some highlights:
- hid-sony improvements of Sixaxis device support by Antonio Ospite
- hid-hyperv driven devices can now be used as wakeup source, by
Dexuan Cui
- hid-lenovo driver is now more generic and supports more devices, by
Jamie Lentin
- hid-huion now supports wider range of tablets, by Nikolai
Kondrashov
- other various unsorted fixes and device ID additions"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (30 commits)
HID: hyperv: register as a wakeup source
HID: sony: Default initialize all elements of the LED max_brightness array to 1
HID: huion: Fix sparse warnings
HID: usbhid: Use flag HID_DISCONNECTED when a usb device is removed
HID: ignore jabra gn9350e
HID: cp2112: add I2C mode
HID: use multi input quirk for 22b9:2968
HID: rmi: only bind the hid-rmi driver to the mouse interface of composite USB devices
HID: rmi: check that report ids exist in the report_id_hash before accessing their size
HID: lenovo: Add support for Compact (BT|USB) keyboard
HID: lenovo: Don't call function in condition, show error codes
HID: lenovo: Prepare support for adding other devices
HID: lenovo: Rename hid-lenovo-tpkbd to hid-lenovo
HID: huion: Handle tablets with UC-Logic vendor ID
HID: huion: Switch to generating report descriptor
HID: huion: Don't ignore other interfaces
HID: huion: Use "tablet" instead of specific model
HID: add quirk for 0x04d9:0xa096 device
HID: i2c-hid: call the hid driver's suspend and resume callbacks
HID: rmi: change logging level of log messages related to unexpected reports
...
|
|
Pull watchdog updates from Wim Van Sebroeck:
- remove unnecessary checks after platform_get_resource()
- fix watchdog api documentation typo's
- imx2_wdt: adds big endianness support
- move restart code to the sunxi watchdog driver
* git://www.linux-watchdog.org/linux-watchdog:
wdt: sunxi: Move restart code to the watchdog driver
Documentation: fix two typos in watchdog-api.txt
watchdog: imx2_wdt: adds big endianness support.
watchdog: shwdt: Remove the unnecessary check of resource after platform_get_resource()
watchdog: lantiq_wdt: Remove the un-necessary check of resource after platform_get_resource()
watchdog: dw_wdt: Remove the un-necessary check after platform_get_resource()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"Again, ACPICA leads the pack (47 commits), followed by cpufreq (18
commits) and system suspend/hibernation (9 commits).
From the new code perspective, the ACPICA update brings ACPI 5.1 to
the table, including a new device configuration object called _DSD
(Device Specific Data) that will hopefully help us to operate device
properties like Device Trees do (at least to some extent) and changes
related to supporting ACPI on ARM.
Apart from that we have hibernation changes making it use radix trees
to store memory bitmaps which should speed up some operations carried
out by it quite significantly. We also have some power management
changes related to suspend-to-idle (the "freeze" sleep state) support
and more preliminary changes needed to support ACPI on ARM (outside of
ACPICA).
The rest is fixes and cleanups pretty much everywhere.
Specifics:
- ACPICA update to upstream version 20140724. That includes ACPI 5.1
material (support for the _CCA and _DSD predefined names, changes
related to the DMAR and PCCT tables and ARM support among other
things) and cleanups related to using ACPICA's header files. A
major part of it is related to acpidump and the core code used by
that utility. Changes from Bob Moore, David E Box, Lv Zheng,
Sascha Wildner, Tomasz Nowicki, Hanjun Guo.
- Radix trees for memory bitmaps used by the hibernation core from
Joerg Roedel.
- Support for waking up the system from suspend-to-idle (also known
as the "freeze" sleep state) using ACPI-based PCI wakeup signaling
(Rafael J Wysocki).
- Fixes for issues related to ACPI button events (Rafael J Wysocki).
- New device ID for an ACPI-enumerated device included into the
Wildcat Point PCH from Jie Yang.
- ACPI video updates related to backlight handling from Hans de Goede
and Linus Torvalds.
- Preliminary changes needed to support ACPI on ARM from Hanjun Guo
and Graeme Gregory.
- ACPI PNP core cleanups from Arjun Sreedharan and Zhang Rui.
- Cleanups related to ACPI_COMPANION() and ACPI_HANDLE() macros
(Rafael J Wysocki).
- ACPI-based device hotplug cleanups from Wei Yongjun and Rafael J
Wysocki.
- Cleanups and improvements related to system suspend from Lan
Tianyu, Randy Dunlap and Rafael J Wysocki.
- ACPI battery cleanup from Wei Yongjun.
- cpufreq core fixes from Viresh Kumar.
- Elimination of a deadband effect from the cpufreq ondemand governor
and intel_pstate driver cleanups from Stratos Karafotis.
- 350MHz CPU support for the powernow-k6 cpufreq driver from Mikulas
Patocka.
- Fix for the imx6 cpufreq driver from Anson Huang.
- cpuidle core and governor cleanups from Daniel Lezcano, Sandeep
Tripathy and Mohammad Merajul Islam Molla.
- Build fix for the big_little cpuidle driver from Sachin Kamat.
- Configuration fix for the Operation Performance Points (OPP)
framework from Mark Brown.
- APM cleanup from Jean Delvare.
- cpupower utility fixes and cleanups from Peter Senna Tschudin,
Andrey Utkin, Himangi Saraogi, Rickard Strandqvist, Thomas
Renninger"
* tag 'pm+acpi-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (118 commits)
ACPI / LPSS: add LPSS device for Wildcat Point PCH
ACPI / PNP: Replace faulty is_hex_digit() by isxdigit()
ACPICA: Update version to 20140724.
ACPICA: ACPI 5.1: Update for PCCT table changes.
ACPICA/ARM: ACPI 5.1: Update for GTDT table changes.
ACPICA/ARM: ACPI 5.1: Update for MADT changes.
ACPICA/ARM: ACPI 5.1: Update for FADT changes.
ACPICA: ACPI 5.1: Support for the _CCA predifined name.
ACPICA: ACPI 5.1: New notify value for System Affinity Update.
ACPICA: ACPI 5.1: Support for the _DSD predefined name.
ACPICA: Debug object: Add current value of Timer() to debug line prefix.
ACPICA: acpihelp: Add UUID support, restructure some existing files.
ACPICA: Utilities: Fix local printf issue.
ACPICA: Tables: Update for DMAR table changes.
ACPICA: Remove some extraneous printf arguments.
ACPICA: Update for comments/formatting. No functional changes.
ACPICA: Disassembler: Add support for the ToUUID opererator (macro).
ACPICA: Remove a redundant cast to acpi_size for ACPI_OFFSET() macro.
ACPICA: Work around an ancient GCC bug.
ACPI / processor: Make it possible to get local x2apic id via _MAT
...
|
|
Pull SCSI updates from James Bottomley:
"This patch set consists of the usual driver updates (ufs, storvsc,
pm8001 hpsa). It also has removal of the user space target driver
code (everyone is using LIO now), a partial PCI MSI-X update, more
multi-queue updates, conversion to 64 bit LUNs (so we could
theoretically cope with any LUN returned by a device) and placeholder
support for the ZBC device type (Shingle drives), plus an assortment
of minor updates and bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (143 commits)
scsi: do not issue SCSI RSOC command to Promise Vtrak E610f
vmw_pvscsi: Use pci_enable_msix_exact() instead of pci_enable_msix()
pm8001: Fix invalid return when request_irq() failed
lpfc: Remove superfluous call to pci_disable_msix()
isci: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Cleanup bfad_setup_intr() function
bfa: Do not call pci_enable_msix() after it failed once
fnic: Use pci_enable_msix_exact() instead of pci_enable_msix()
scsi: use short driver name for per-driver cmd slab caches
scsi_debug: support scsi-mq, queues and locks
Drivers: add blist flags
scsi: ufs: fix endianness sparse warnings
scsi: ufs: make undeclared functions static
bnx2i: Update driver version to 2.7.10.1
pm8001: fix a memory leak in nvmd_resp
pm8001: fix update_flash
pm8001: fix a memory leak in flash_update
pm8001: Cleaning up uninitialized variables
pm8001: Fix to remove null pointer checks that could never happen
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There've been many updates in ASoC side at this time, especially the
framework enhancement for multiple CODECs on a single DAI and more
componentization works.
The only major change in ALSA core is the addition of timestamp type
in sw_params field. This should behave in backward compatible way.
Other than that, there are lots of small changes and new drivers in
wide range, including a large code cut in HD-audio driver for
deprecated static quirks. Some highlights are below:
ALSA Core:
- Add the new timestamp type field to sw_params to choose
MONOTONIC_RAW type
HD-audio:
- Continued conversion to standard printk macros, generic code
cleanups
- Removal of obsoleted static quirk codes for Conexant and C-Media
codecs
- Fixups for HP Envy TS, Dell XPS 15, HP and Dell mute/mic LED,
Gigabyte BXBT-2807 mobo
- Intel Braswell support
ASoC:
- Support for multiple CODECs attached to a single DAI, enabling
systems with for example multiple DAC/speaker drivers on a single
link, contributed by Benoit Cousson based on work from Misael Lopez
Cruz
- Support for byte controls larger than 256 bytes based on the use of
TLVs contributed by Omair Mohammed Abdullah
- More componentisation work from Lars-Peter Clausen
- The remainder of the conversions of CODEC drivers to params_width()
by Mark Brown
- Drivers for Cirrus Logic CS4265, Freescale i.MX ASRC blocks,
Realtek RT286 and RT5670, Rockchip RK3xxx I2S controllers and Texas
Instruments TAS2552
- Lots of updates and fixes, especially to the DaVinci, Intel,
Freescale, Realtek, and rcar drivers"
* tag 'sound-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (402 commits)
ALSA: usb-audio: Whitespace cleanups for sound/usb/midi.*
ALSA: usb-audio: Respond to suspend and resume callbacks for MIDI input
sound/oss/pss: Remove typedefs pss_mixerdata and pss_confdata
sound/oss/opl3: Remove typedef opl_devinfo
ALSA: fireworks: fix specifiers in format strings for propper output
ASoC: imx-audmux: Use uintptr_t for port numbers
ASoC: davinci: Enable menuconfig entry for McASP
ASoC: fsl_asrc: Don't access members of config before checking it
ASoC: fsl_sarc_dma: Check pair before using it
ASoC: adau1977: Fix truncation warning on 64 bit architectures
ALSA: virtuoso: add Xonar Essence STX II support
ALSA: riptide: fix %d confusingly prefixed with 0x in format strings
ALSA: fireworks: fix %d confusingly prefixed with 0x in format strings
ALSA: hda - add codec ID for Braswell display audio codec
ALSA: hda - add PCI IDs for Intel Braswell
ALSA: usb-audio: Adjust Gamecom 780 volume level
ALSA: usb-audio: improve dmesg source grepability
ASoC: rt5670: Fix duplicate const warnings
ASoC: rt5670: Staticise non-exported symbols
ASoC: Intel: update stream only on stream IPC msgs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi
Pull HSI changes from Sebastian Reichel:
"Misc fixes in SSI related drivers"
* tag 'hsi-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
HSI: omap_ssi: Fix return value check in ssi_debug_add_ctrl()
HSI: omap_ssi_port: Fix return value check in ssi_debug_add_port()
HSI: ssi_protocol: Fix sparse non static symbol warning
drivers/hsi/controllers/omap_ssi{,_port}.c: fix failure checks
|
|
Pull power supply changes from Sebastian Reichel:
- Added iPaq h3xxx battery driver
- Added Broadcom STB reset driver
- DT support for rx51-battery
- misc. fixes
* tag 'for-v3.17' of git://git.infradead.org/battery-2.6:
ipaq_micro_battery: fix sparse non static symbol warning
power: add driver for battery reading on iPaq h3xxx
power: twl4030_charger: detect battery presence prior to enabling charger
power: reset: Add reboot driver for brcmstb
power_supply: Fix sparse non static symbol warning
power_supply: Add inlmt,iterm, min/max temp props
charger: tps65090: Allow charger module to be used when no irq
power/reset: Fix GPL v2 license string typo
power: poweroff: gpio: convert to use descriptors
bq27000: report missing device better.
bq27x00_battery: Introduce the use of the managed version of kzalloc
Documentation: DT: Document rx51-battery binding
rx51_battery: convert to iio consumer
bq2415x_charger: Fix Atomic Sleep Bug
|
|
The function may be useful for other drivers, so export it. (Suggested
by Tejun Heo.)
Note that I inverted the return value of glob_match; returning true on
match seemed to make more sense.
Signed-off-by: George Spelvin <linux@horizon.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
All other add functions for lists have the new item as first argument
and the position where it is added as second argument. This was changed
for no good reason in this function and makes using it unnecessary
confusing.
The name was changed to hlist_add_behind() to cause unconverted code to
generate a compile error instead of using the wrong parameter order.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Ken Helias <kenhelias@firemail.de>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> [intel driver bits]
Cc: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
definition and use
The DEFINE_SIMPLE_ATTRIBUTE macro should not end in a ; Fix the one use
in the kernel tree that did not have a semicolon.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, we use a rwlock tb_lock to protect concurrent access to the
whole zram meta table. However, according to the actual access model,
there is only a small chance for upper user to access the same
table[index], so the current lock granularity is too big.
The idea of optimization is to change the lock granularity from whole
meta table to per table entry (table -> table[index]), so that we can
protect concurrent access to the same table[index], meanwhile allow the
maximum concurrency.
With this in mind, several kinds of locks which could be used as a
per-entry lock were tested and compared:
Test environment:
x86-64 Intel Core2 Q8400, system memory 4GB, Ubuntu 12.04,
kernel v3.15.0-rc3 as base, zram with 4 max_comp_streams LZO.
iozone test:
iozone -t 4 -R -r 16K -s 200M -I +Z
(1GB zram with ext4 filesystem, take the average of 10 tests, KB/s)
Test base CAS spinlock rwlock bit_spinlock
-------------------------------------------------------------------
Initial write 1381094 1425435 1422860 1423075 1421521
Rewrite 1529479 1641199 1668762 1672855 1654910
Read 8468009 11324979 11305569 11117273 10997202
Re-read 8467476 11260914 11248059 11145336 10906486
Reverse Read 6821393 8106334 8282174 8279195 8109186
Stride read 7191093 8994306 9153982 8961224 9004434
Random read 7156353 8957932 9167098 8980465 8940476
Mixed workload 4172747 5680814 5927825 5489578 5972253
Random write 1483044 1605588 1594329 1600453 1596010
Pwrite 1276644 1303108 1311612 1314228 1300960
Pread 4324337 4632869 4618386 4457870 4500166
To enhance the possibility of access the same table[index] concurrently,
set zram a small disksize(10MB) and let threads run with large loop
count.
fio test:
fio --bs=32k --randrepeat=1 --randseed=100 --refill_buffers
--scramble_buffers=1 --direct=1 --loops=3000 --numjobs=4
--filename=/dev/zram0 --name=seq-write --rw=write --stonewall
--name=seq-read --rw=read --stonewall --name=seq-readwrite
--rw=rw --stonewall --name=rand-readwrite --rw=randrw --stonewall
(10MB zram raw block device, take the average of 10 tests, KB/s)
Test base CAS spinlock rwlock bit_spinlock
-------------------------------------------------------------
seq-write 933789 999357 1003298 995961 1001958
seq-read 5634130 6577930 6380861 6243912 6230006
seq-rw 1405687 1638117 1640256 1633903 1634459
rand-rw 1386119 1614664 1617211 1609267 1612471
All the optimization methods show a higher performance than the base,
however, it is hard to say which method is the most appropriate.
On the other hand, zram is mostly used on small embedded system, so we
don't want to increase any memory footprint.
This patch pick the bit_spinlock method, pack object size and page_flag
into an unsigned long table.value, so as to not increase any memory
overhead on both 32-bit and 64-bit system.
On the third hand, even though different kinds of locks have different
performances, we can ignore this difference, because: if zram is used as
zram swapfile, the swap subsystem can prevent concurrent access to the
same swapslot; if zram is used as zram-blk for set up filesystem on it,
the upper filesystem and the page cache also prevent concurrent access
of the same block mostly. So we can ignore the different performances
among locks.
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Weijie Yang <weijie.yang@samsung.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some architectures (eg, hexagon and PowerPC) could use PAGE_SHIFT of 16
or more. In these cases u16 is not sufficiently large to represent a
compressed page's size so use size_t.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reported-by: Weijie Yang <weijie.yang@samsung.com>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Drop SECTOR_SIZE define, because it's not used.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Weijie Yang <weijie.yang@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Andrew Morton has recently noted that `struct table' actually represents
table entry and, thus, should be renamed. Rename to `zram_table_entry'.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Weijie Yang <weijie.yang@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With memoryless node support being worked on, it's possible that for
optimizations that a node may not have a non-NULL zonelist. When
CONFIG_NUMA is enabled and node 0 is memoryless, this means the zonelist
for first_online_node may become NULL.
The oom killer requires a zonelist that includes all memory zones for
the sysrq trigger and pagefault out of memory handler.
Ensure that a non-NULL zonelist is always passed to the oom killer.
[akpm@linux-foundation.org: fix non-numa build]
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
range
When limiting memory by mem= and ACPI DSDT table has PNP0C80,
firmware_map_entrys of same memory range are allocated and memmap X
sysfses which have same memory range are created as follows:
# cat /sys/firmware/memmap/0/*
0x407ffffffff
0x40000000000
System RAM
# cat /sys/firmware/memmap/33/*
0x407ffffffff
0x40000000000
System RAM
# cat /sys/firmware/memmap/35/*
0x407ffffffff
0x40000000000
System RAM
In this case, when hot-removing memory, kernel panic occurs, showing
following call trace:
BUG: unable to handle kernel paging request at 00000001003e000b
IP: sysfs_open_file+0x46/0x2b0
PGD 203a89fe067 PUD 0
Oops: 0000 [#1] SMP
...
Call Trace:
do_dentry_open+0x1ef/0x2a0
finish_open+0x31/0x40
do_last+0x57c/0x1220
path_openat+0xc2/0x4c0
do_filp_open+0x4b/0xb0
do_sys_open+0xf3/0x1f0
SyS_open+0x1e/0x20
system_call_fastpath+0x16/0x1b
The problem occurs as follows:
When calling e820_reserve_resources(), firmware_map_entrys of all e820
memory map are allocated. And all firmware_map_entrys is added
map_entries list as follows:
map_entries
-> +--- entry A --------+ -> ...
| start 0x407ffffffff|
| end 0x40000000000|
| type System RAM |
+--------------------+
After that, if ACPI DSDT table has PNP0C80 and the memory range is
limited by mem=, the PNP0C80 is hot-added. Then firmware_map_entry of
PNP0C80 is allocated and added map_entries list as follows:
map_entries
-> +--- entry A --------+ -> ... -> +--- entry B --------+
| start 0x407ffffffff| | start 0x407ffffffff|
| end 0x40000000000| | end 0x40000000000|
| type System RAM | | type System RAM |
+--------------------+ +--------------------+
Then memmap 0 sysfs for entry B is created.
After that, firmware_memmap_init() creates memmap sysfses of all
firmware_map_entrys in map_entries list. As a result, memmap 33 sysfs
for entry A and memmap 35 sysfs for entry B are created. But kobject of
entry B has been used by memmap 0 sysfs. So when creating memmap 35
sysfs, the kobject is broken.
If hot-removing memory, memmap 0 sysfs is destroyed and kobject of
memmap 0 sysfs is freed. But the kobject can be accessed via memmap 35
sysfs. So when open memmap 35 sysfs, kernel panic occurs.
This patch checks whether there is firmware_map_entry of same memory
range in map_entries list and don't allocate firmware_map_entry of same
memroy range.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
firmware_map_find_entry_bootmem()
firmware_map_add_hotplug() calls firmware_map_find_entry_bootmem() to
get free firmware_map_entry. But end arguments is not correct. So
firmware_map_find_entry_bootmem() cannot not find firmware_map_entry.
The patch passes the correct end argument to firmware_map_find_entry_bootmem().
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently map_vm_area() takes (struct page *** pages) as third argument,
and after mapping, it moves (*pages) to point to (*pages +
nr_mappped_pages).
It looks like this kind of increment is useless to its caller these
days. The callers don't care about the increments and actually they're
trying to avoid this by passing another copy to map_vm_area().
The caller can always guarantee all the pages can be mapped into vm_area
as specified in first argument and the caller only cares about whether
map_vm_area() fails or not.
This patch cleans up the pointer movement in map_vm_area() and updates
its callers accordingly.
Signed-off-by: WANG Chao <chaowang@redhat.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Historically, we exported shared pages to userspace via sysinfo(2)
sharedram and /proc/meminfo's "MemShared" fields. With the advent of
tmpfs, from kernel v2.4 onward, that old way for accounting shared mem
was deemed inaccurate and we started to export a hard-coded 0 for
sysinfo.sharedram. Later on, during the 2.6 timeframe, "MemShared" got
re-introduced to /proc/meminfo re-branded as "Shmem", but we're still
reporting sysinfo.sharedmem as that old hard-coded zero, which makes the
"shared memory" report inconsistent across interfaces.
This patch leverages the addition of explicit accounting for pages used
by shmem/tmpfs -- "4b02108 mm: oom analysis: add shmem vmstat" -- in
order to make the users of sysinfo(2) and si_meminfo*() friends aware of
that vmstat entry and make them report it consistently across the
interfaces, as well to make sysinfo(2) returned data consistent with our
current API documentation states.
Signed-off-by: Rafael Aquini <aquini@redhat.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use the newer and more pleasant kstrtoull() to replace
simple_strtoull(), because simple_strtoull() is marked for obsoletion.
Signed-off-by: Zhang Zhen <zhenzhang.zhang@huawei.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Conventionally, we put output param to the end of param list and put the
'base' ahead of 'size', but cma_declare_contiguous() doesn't look like
that, so change it.
Additionally, move down cma_areas reference code to the position where
it is really needed.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Gleb Natapov <gleb@kernel.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, there are two users on CMA functionality, one is the DMA
subsystem and the other is the KVM on powerpc. They have their own code
to manage CMA reserved area even if they looks really similar. From my
guess, it is caused by some needs on bitmap management. KVM side wants
to maintain bitmap not for 1 page, but for more size. Eventually it use
bitmap where one bit represents 64 pages.
When I implement CMA related patches, I should change those two places
to apply my change and it seem to be painful to me. I want to change
this situation and reduce future code management overhead through this
patch.
This change could also help developer who want to use CMA in their new
feature development, since they can use CMA easily without copying &
pasting this reserved area management code.
In previous patches, we have prepared some features to generalize CMA
reserved area management and now it's time to do it. This patch moves
core functions to mm/cma.c and change DMA APIs to use these functions.
There is no functional change in DMA APIs.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Gleb Natapov <gleb@kernel.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
PPC KVM's CMA area management requires arbitrary bitmap granularity,
since they want to reserve very large memory and manage this region with
bitmap that one bit for several pages to reduce management overheads.
So support arbitrary bitmap granularity for following generalization.
[akpm@linux-foundation.org: s/1/1UL/]
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Gleb Natapov <gleb@kernel.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
PPC KVM's CMA area management needs alignment constraint on CMA region.
So support it to prepare generalization of CMA area management
functionality.
Additionally, add some comments which tell us why alignment constraint
is needed on CMA region.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Gleb Natapov <gleb@kernel.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
To prepare future generalization work on CMA area management code, we
need to separate core CMA management codes from DMA APIs. We will
extend these core functions to cover requirements of PPC KVM's CMA area
management functionality in following patches. This separation helps us
not to touch DMA APIs while extending core functions.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In store_mem_state(), we have:
...
334 else if (!strncmp(buf, "offline", min_t(int, count, 7)))
335 online_type = -1;
...
355 case -1:
356 ret = device_offline(&mem->dev);
357 break;
...
Here, "offline" is hard coded as -1.
This patch does the following renaming:
ONLINE_KEEP -> MMOP_ONLINE_KEEP
ONLINE_KERNEL -> MMOP_ONLINE_KERNEL
ONLINE_MOVABLE -> MMOP_ONLINE_MOVABLE
and introduces MMOP_OFFLINE = -1 to avoid hard coding.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Hu Tao <hutao@cn.fujitsu.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
state of memory_block
We use the following command to online a memory_block:
echo online|online_kernel|online_movable > /sys/devices/system/memory/memoryXXX/state
But, if we do the following:
echo online_fhsjkghfkd > /sys/devices/system/memory/memoryXXX/state
the block will also be onlined.
This is because the following code in store_mem_state() does not compare
the whole string, but only the prefix of the string.
store_mem_state()
{
......
328 if (!strncmp(buf, "online_kernel", min_t(int, count, 13)))
Here, only compare the first 13 letters of the string. If we give "online_kernelXXXXXX",
it will be recognized as online_kernel, which is incorrect.
329 online_type = ONLINE_KERNEL;
330 else if (!strncmp(buf, "online_movable", min_t(int, count, 14)))
We have the same problem here,
331 online_type = ONLINE_MOVABLE;
332 else if (!strncmp(buf, "online", min_t(int, count, 6)))
here,
(Here is more problematic. If we give online_movalbe, which is a typo
of online_movable, it will be recognized as online without noticing the
author.)
333 online_type = ONLINE_KEEP;
334 else if (!strncmp(buf, "offline", min_t(int, count, 7)))
and here.
335 online_type = -1;
336 else {
337 ret = -EINVAL;
338 goto err;
339 }
......
}
This patch fixes this problem by using sysfs_streq() to compare the
whole string.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Reported-by: Hu Tao <hutao@cn.fujitsu.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Gu Zheng <guz.fnst@cn.fujitsu.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It must be tristate to avoid broken dependencies with kernel built-in
usb network drivers when usb support is module only.
When net config option is set, least surprize default should match usb.
Wireless RNDIS USB driver used to select USB_USBNET. USB_USBNET now
depends on USB_NET_DRIVERS so the latter should be selected as well.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.
Found by using regex suggested by Joe Perches.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
WS2008R2 is a supported platform and it turns out that the maximum sendbuf
size that ws2008R2 can support is only 15MB. Make the necessary
adjustment.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 35b1de5 ("rdma/cxgb4: Fixes cxgb4 probe failure in VM when PF is exposed
through PCI Passthrough") introduced a regression, where VF failed to
initialize for Physical function 0 to Physical Function 3. In the above
commit, we removed the code which used to enable sriov for PF0 to PF3. Now
adding it back to get sriov working.
V2:
Removed SRIOV loop for PF[0..3] to instantiate the VF's as per David Miller's
comment
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull IDE cleanup from David Miller:
"Just one minor cleanup"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
ide: use module_platform_driver()
|
|
Pull sparc updates from David Miller:
1) Add sparc RAM output to /proc/iomem, from Bob Picco.
2) Allow seeks on /dev/mdesc, from Khalid Aziz.
3) Cleanup sparc64 I/O accessors, from Sam Ravnborg.
4) If update_mmu_cache{,_pmd}() is called with an not-valid mapping, do
not insert it into the TLB miss hash tables otherwise we'll
livelock. Based upon work by Christopher Alexander Tobias Schulze.
5) Fix BREAK detection in sunsab driver when no actual characters are
pending, from Christopher Alexander Tobias Schulze.
6) Because we have modules --> openfirmware --> vmalloc ordering of
virtual memory, the lazy VMAP TLB flusher can cons up an invocation
of flush_tlb_kernel_range() that covers the openfirmware address
range. Unfortunately this will flush out the firmware's locked TLB
mapping which causes all kinds of trouble. Just split up the flush
request if this happens, but in the long term the lazy VMAP flusher
should probably be made a little bit smarter.
Based upon work by Christopher Alexander Tobias Schulze.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next:
sparc64: Fix up merge thinko.
sparc: Add "install" target
arch/sparc/math-emu/math_32.c: drop stray break operator
sparc64: ldc_connect() should not return EINVAL when handshake is in progress.
sparc64: Guard against flushing openfirmware mappings.
sunsab: Fix detection of BREAK on sunsab serial console
bbc-i2c: Fix BBC I2C envctrl on SunBlade 2000
sparc64: Do not insert non-valid PTEs into the TSB hash table.
sparc64: avoid code duplication in io_64.h
sparc64: reorder functions in io_64.h
sparc64: drop unused SLOW_DOWN_IO definitions
sparc64: remove macro indirection in io_64.h
sparc64: update IO access functions in PeeCeeI
sparcspkr: use sbus_*() primitives for IO
sparc: Add support for seek and shorter read to /dev/mdesc
sparc: use %s for unaligned panic
drivers/sbus/char: Micro-optimization in display7seg.c
display7seg: Introduce the use of the managed version of kzalloc
sparc64 - add mem to iomem resource
|
|
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull randomness updates from Ted Ts'o:
"Cleanups and bug fixes to /dev/random, add a new getrandom(2) system
call, which is a superset of OpenBSD's getentropy(2) call, for use
with userspace crypto libraries such as LibreSSL.
Also add the ability to have a kernel thread to pull entropy from
hardware rng devices into /dev/random"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
hwrng: Pass entropy to add_hwgenerator_randomness() in bits, not bytes
random: limit the contribution of the hw rng to at most half
random: introduce getrandom(2) system call
hw_random: fix sparse warning (NULL vs 0 for pointer)
random: use registers from interrupted code for CPU's w/o a cycle counter
hwrng: add per-device entropy derating
hwrng: create filler thread
random: add_hwgenerator_randomness() for feeding entropy from devices
random: use an improved fast_mix() function
random: clean up interrupt entropy accounting for archs w/o cycle counters
random: only update the last_pulled time if we actually transferred entropy
random: remove unneeded hash of a portion of the entropy pool
random: always update the entropy pool under the spinlock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security subsystem updates from James Morris:
"In this release:
- PKCS#7 parser for the key management subsystem from David Howells
- appoint Kees Cook as seccomp maintainer
- bugfixes and general maintenance across the subsystem"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (94 commits)
X.509: Need to export x509_request_asymmetric_key()
netlabel: shorter names for the NetLabel catmap funcs/structs
netlabel: fix the catmap walking functions
netlabel: fix the horribly broken catmap functions
netlabel: fix a problem when setting bits below the previously lowest bit
PKCS#7: X.509 certificate issuer and subject are mandatory fields in the ASN.1
tpm: simplify code by using %*phN specifier
tpm: Provide a generic means to override the chip returned timeouts
tpm: missing tpm_chip_put in tpm_get_random()
tpm: Properly clean sysfs entries in error path
tpm: Add missing tpm_do_selftest to ST33 I2C driver
PKCS#7: Use x509_request_asymmetric_key()
Revert "selinux: fix the default socket labeling in sock_graft()"
X.509: x509_request_asymmetric_keys() doesn't need string length arguments
PKCS#7: fix sparse non static symbol warning
KEYS: revert encrypted key change
ima: add support for measuring and appraising firmware
firmware_class: perform new LSM checks
security: introduce kernel_fw_from_file hook
PKCS#7: Missing inclusion of linux/err.h
...
|
|
'for-3.17/hyperv', 'for-3.17/i2c', 'for-3.17/lenovo', 'for-3.17/rmi' and 'for-3.17/sony' into for-linus
|
|
Eliminate boilerplate code by using module_platform_driver().
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
arch/sparc/mm/init_64.c
Conflict was simple non-overlapping additions.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/Makefile
net/ipv6/sysctl_net_ipv6.c
Two ipv6_table_template[] additions overlap, so the index
of the ipv6_table[x] assignments needed to be adjusted.
In the drivers/net/Makefile case, we've gotten rid of the
garbage whereby we had to list every single USB networking
driver in the top-level Makefile, there is just one
"USB_NETWORKING" that guards everything.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer and time updates from Thomas Gleixner:
"A rather large update of timers, timekeeping & co
- Core timekeeping code is year-2038 safe now for 32bit machines.
Now we just need to fix all in kernel users and the gazillion of
user space interfaces which rely on timespec/timeval :)
- Better cache layout for the timekeeping internal data structures.
- Proper nanosecond based interfaces for in kernel users.
- Tree wide cleanup of code which wants nanoseconds but does hoops
and loops to convert back and forth from timespecs. Some of it
definitely belongs into the ugly code museum.
- Consolidation of the timekeeping interface zoo.
- A fast NMI safe accessor to clock monotonic for tracing. This is a
long standing request to support correlated user/kernel space
traces. With proper NTP frequency correction it's also suitable
for correlation of traces accross separate machines.
- Checkpoint/restart support for timerfd.
- A few NOHZ[_FULL] improvements in the [hr]timer code.
- Code move from kernel to kernel/time of all time* related code.
- New clocksource/event drivers from the ARM universe. I'm really
impressed that despite an architected timer in the newer chips SoC
manufacturers insist on inventing new and differently broken SoC
specific timers.
[ Ed. "Impressed"? I don't think that word means what you think it means ]
- Another round of code move from arch to drivers. Looks like most
of the legacy mess in ARM regarding timers is sorted out except for
a few obnoxious strongholds.
- The usual updates and fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
timekeeping: Fixup typo in update_vsyscall_old definition
clocksource: document some basic timekeeping concepts
timekeeping: Use cached ntp_tick_length when accumulating error
timekeeping: Rework frequency adjustments to work better w/ nohz
timekeeping: Minor fixup for timespec64->timespec assignment
ftrace: Provide trace clocks monotonic
timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
seqcount: Add raw_write_seqcount_latch()
seqcount: Provide raw_read_seqcount()
timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
timekeeping: Create struct tk_read_base and use it in struct timekeeper
timekeeping: Restructure the timekeeper some more
clocksource: Get rid of cycle_last
clocksource: Move cycle_last validation to core code
clocksource: Make delta calculation a function
wireless: ath9k: Get rid of timespec conversions
drm: vmwgfx: Use nsec based interfaces
drm: i915: Use nsec based interfaces
timekeeping: Provide ktime_get_raw()
hangcheck-timer: Use ktime_get_ns()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Nothing spectacular from the irq department this time:
- overhaul of the crossbar chip driver
- overhaul of the spear shirq chip driver
- support for the atmel-aic chip
- code move from arch to drivers
- the usual tiny fixlets
- two reverts worth to mention which undo the too simple attempt of
supporting wakeup interrupts on shared interrupt lines"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
Revert "irq: Warn when shared interrupts do not match on NO_SUSPEND"
Revert "PM / sleep / irq: Do not suspend wakeup interrupts"
irq: Warn when shared interrupts do not match on NO_SUSPEND
irqchip: atmel-aic: Define irq fixups for atmel SoCs
irqchip: atmel-aic: Implement RTC irq fixup
irqchip: atmel-aic: Add irq fixup infrastructure
irqchip: atmel-aic: Add atmel AIC/AIC5 drivers
irqchip: atmel-aic: Move binding doc to interrupt-controller directory
genirq: generic chip: Export irq_map_generic_chip function
PM / sleep / irq: Do not suspend wakeup interrupts
irqchip: or1k-pic: Migrate from arch/openrisc/
irqchip: crossbar: Allow for quirky hardware with direct hardwiring of GIC
documentation: dt: omap: crossbar: Add description for interrupt consumer
irqchip: crossbar: Introduce centralized check for crossbar write
irqchip: crossbar: Introduce ti, max-crossbar-sources to identify valid crossbar mapping
irqchip: crossbar: Add kerneldoc for crossbar_domain_unmap callback
irqchip: crossbar: Set cb pointer to null in case of error
irqchip: crossbar: Change the goto naming
irqchip: crossbar: Return proper error value
irqchip: crossbar: Fix kerneldoc warning
...
|
|
Enabling a Virtual Interface can result in an interrupt during the processing
of the VI Enable command and, in some paths, result in an attempt to issue
another command in the interrupt context, eventually crashing the system. Thus,
we disable interrupts during the course of the VI Enable command and ensure
enable doesn't sleep.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
USB network drivers are already handled in drivers/net/usb/Kconfig.
Let's save the maintenance burden of dependencies in drivers/net/Makefile.
The newly introduced USB_NET_DRIVERS umbrella config option defaults
to 'y' so as to minimize the changes of behavior.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|