| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add dt-based retrieval of host sdio pm capabilities. Based on
the dt based discovery do a bus init in the resume function.
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add support for optional pm capabilities such as MMC_PM_KEEP_POWER
and MMC_PM_WAKE_SDIO_IRQ.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
For regulator vmmc/vmmcq, use voltage range as below
3.3v/3.0v: (2.7v, 3.6v)
1.8v: (1.7v, 1.95v)
Original code uses the precise value which may fail in regulator
driver if it does NOT support the precise voltage.
Signed-off-by: Jialing Fu <jlfu@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This patch adds support for the SD/MMC host controller found
on Wondermedia 8xxx series SoCs, currently supported under
arm/arch-vt8500.
A binding document is also included, based on mmc.txt with
additional properties.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
RPMB partition is accessing though /dev/block/mmcXrpmb device
User callers can read and write entire data frame(s) as defined
by JEDEC Standard JESD84-A441, using standard IOCTL interface.
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Provide support for automatically sending Set Block Count
(CMD23) messages. Used at least for RPMB support.
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Extend current sysfs access to ext_csd rpmb parameters (RPMB partition
size) and rel_sector information.
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Do not scan rpmb partitions for "soft" partitions, since the rpmb
partition contains protected data. Silences the following message
during boot:
mmcblkXRPMB: unknown partition table
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Following JEDEC standard, if the mmc supports RPMB partition,
a new interface is created and exposed via /dev/block.
Users will be able to access RPMB partition using standard
mmc IOCTL commands.
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Enable the quirk SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN since
SD_CAPABILITIES_1[15:8](BASE_FREQ) can't get correct base clock value.
It returns a fixed pre-set value like 200 on some sdhci-pxav3 based
platforms like MMP3 while return 0 on the other sdhci-pxav3 based
platforms. So we enable the quirk and get the base clock via function
get_max_clock. Also add get_max_clock.
Reported-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Philip Rakity <prakity@Marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
There are discrepancies with regards to how MMC capabilities
are carried throughout the subsystem. Let's standardise them
to eliminate any confusion.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
All MXS users have been converted to device tree and the board files have
been removed.
No need to keep platform data in the driver.
Also move bus_width declaration in the beggining of mxs_mmc_probe() to
avoid: 'warning: ISO C90 forbids mixed declarations and code'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Before this patch, we always used only single sg entry for SDIO transfer.
This patch switches to using multiple sg entries. In the case of dwmci,
it supports only up to 4KB size per single sg entry. So if we want to
transfer more than 4KB, we should send more than 1 command.
When we tested before applying this patch, it took around 335 us for
5K(5120) bytes transfer with dwmci controller. After applying this patch,
it takes 242 us for 5K bytes. So this patch makes around 38% performance
improvement for 5K bytes transfer. If the transfer size is bigger, then
the performance improvement ratio will be increased.
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
There are infinite loops in the mmc code that can be caused by bad
hardware. The code will loop forever if the device never comes back
from program mode, R1_STATE_PRG, and it is not ready for data,
R1_READY_FOR_DATA.
A long timeout is added to prevent the code from looping forever.
The timeout will occur if the device never comes back from program
state or the device never becomes ready for data.
It's not clear whether the timeout will do more than log a pr_err()
and then start a fresh hang all over again. We may need to extend
this patch later to perform some kind of reset of the device (is
that possible?) or rejection of new I/O to the device.
Signed-off-by: Trey Ramsay <tramsay@linux.vnet.ibm.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The patch "dw_mmc: fix multiple drv_data NULL dereferences" has
unfortunately clashed with my "mmc: dw_mmc: constify dw_mci_idmac_ops
in exynos back-end" patch, causing new warnings to appear.
This should hopefully fix the issue for good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The at91-mci driver is not needed anymore since the atmel-mci driver now
supports all Atmel devices.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
MMC debounce clock is applicable only for omap2430, warning message gets
printed when enable fails for debounce clock. Remove the get debounce clock
failure message as it is noisy for other platforms.
Signed-off-by: Balaji T K <balajitk@ti.com>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Maximum bus frequency can be limited by external circuitry like level
shifters etc. Allow passing this value from DT.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This allows DT-driven board to set up the pin mux only when the driver
is in use.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
When a SD card is initialized some data transfers of 64 and 8 bytes
are issued. It seems the DMA has some problems dealing with these kind
of "short" transfers, leading sometimes to the SD card not being detected.
In order to solve this problem, do not use DMA for transfer sizes lower
than the sector size.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Since v3.2 we have nice macro to define the platform driver's init and exit
calls. This patch simplifies the dw_mmc platform driver by using that macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Girish K S <girish.shivanajappa@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
In case both 'req' and 'mq->mqrq_prev->req' are null, there is no request
to be processed. That means there is no need to switch buffer.
Switching buffer is required only after finishing 'issue_fn'.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Per Forlin <per.forlin@stericsson.com>
Tested-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: Philip Rakity <prakity@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
On some systems, e.g., kzm9g, MMCIF interfaces can produce spurious
interrupts without any active request. To prevent the Oops, that results
in such cases, don't dereference the mmc request pointer until we make
sure, that we are indeed processing such a request.
Reported-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Cc: stable@vger.kernel.org
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The vmmc regulator enable in sdhci_add_host is NOT necessary since
it can be enabled during mmc_power_up by function mmc_regulator_set_ocr.
And this extra enable will make regulator_enable/regulator_disable
unbalanced. Consequently, vmmc can't be disabled during mmc_power_off.
Also, if the vqmmc regulator exists, it should be enabled regardless it
support 1.8v or not.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This reverts commit 8464dd52d3198dd05, which was a misapplied debugging
version of the patch, not the final patch itself.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: stable@vger.kernel.org
|
|
2abeb5c5ded2 ("Add clk_(enable/disable) in runtime suspend/resume")
added the capability to stop the clocks when the device is runtime
suspended, but forgot to handle the case of the card-detect using
an external gpio.
Therefore in the case that runtime-pm is enabled, start the io-clock
when a card is inserted and stop it again once it is removed.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Set chan_mux[DA9055_ADC_ADCIN3] = DA9055_ADC_MUX_ADCIN3.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This is the HWMON patch for DA9055 PMIC and has got dependency on the
DA9055 MFD core.
This patch monitors the DA9055 PMIC's ADC channels vddout, junction temperature
and auxiliary channels.
This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[Guenter Roeck: Dropped __devinit, __devexit, __devexit_p]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Since N4xx, N5xx, D4xx, and D5xx are now reliably detected using the model ID
and the stepping/mask, drop the respective entries from tjmax_table.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
Make the code easier to extend and easier to adjust by using a model table
listing CPU models, stepping/mask, and associated TjMax.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
So far, we use the NM10 Express Chipset PCI chip ID to detect TjMax for
Atom CPUs with model 0x1c. As it turns out, we can use the CPU stepping
(x86_mask) for the same purpose; stepping is 10 for all model 0x1c CPUs
with TjMax of 100 degrees C. This was verified by checking the output of
/proc/cpuinfo for the respective CPUs (D4xx, D5xx, N4xx, N5xx).
Other CPUs currently covered by the same code (Exx, Z6xx, Z2460) are not
supported by the NM10 Express Chipset. Most of those CPUs have TjMax of 90
degrees C, except for E6xxT models which have a TjMax of 110 degrees C.
E6xxT CPUs can however not be detected by software.
Calculate TjMax for Atom CPUs as follows. Note that the listed values are not
correct in some cases (230, 330). tjmax_table is used for those to override
the default values.
ID Stepping TjMax Models
0x1c 10 100 D4xx, N4xx, D5xx, N5xx
0x1c not 10 90 Z5xx, N2xx, 230, 330, others
0x26 - 90 Atom Tunnel Creek (Exx),
Lincroft (Z6xx)
0x27 - 90 Atom Medfield (Z2460)
0x36 - 100 Atom Cedar Trail (N2xxx, D2xxx)
Also drop the module dependency on PCI.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
Use the module_i2c_driver() macro to make the code smaller
and a bit simpler.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The ADS7830 device is almost the same as the ADS7828,
except that it does 8-bit sampling, instead of 12-bit.
This patch extends the ads7828 driver to support this chip.
Signed-off-by: Guillaume Roguez <guillaume.roguez@savoirfairelinux.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
As there is no reliable way to identify the chip, it is preferable to
remove the detect callback, to avoid misdetection.
Module parameters are not worth it here, so let's get rid of them and
add an ads7828_platform_data structure instead.
Clean the code by removing unused macros, fixing coding style issues,
avoiding function prototypes and using convenient macros such as
module_i2c_driver().
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add family 16h PCI ID to AMD's power driver to allow it report
power consumption on these processors.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This fixes a bit error in the U8500 clock implementation: the
unused p2_pclk12 registered at bit 12 in periphereral group 6
was defined as using bit 11 rather than bit 12.
When walking over and disabling the unused clocks in the tree
at late init time, p2_pclk12 was disabled, by effectively
clearing the but for p2_pclk11 instead of bit 12 as it should
have, thus disabling gpio block 6 and 7.
Reported-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Philippe Begnic <philippe.begnic@st.com>
Cc: stable@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Pull UBI changes from Artem Bityutskiy:
"Fixes for 2 brown-paperbag bugs introduced this merge window by the
fastmap code:
1. The UBI background thread got stuck when a bit-flip happened
because free LEBs was not removed from the "free" tree when we
started using it.
2. I/O debugging checks did not work because we called a sleeping
function in atomic context."
* tag 'upstream-3.7-rc9' of git://git.infradead.org/linux-ubi:
UBI: dont call ubi_self_check_all_ff() in __wl_get_peb()
UBI: remove PEB from free tree in get_peb_for_wl()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
"So, safe fixes my ass.
Commit 8852aac25e79 ("workqueue: mod_delayed_work_on() shouldn't queue
timer on 0 delay") had the side-effect of performing delayed_work
sanity checks even when @delay is 0, which should be fine for any sane
use cases.
Unfortunately, megaraid was being overly ingenious. It seemingly
wanted to use cancel_delayed_work_sync() before cancel_work_sync() was
introduced, but didn't want to waste the space for full delayed_work
as it was only going to use 0 @delay. So, it only allocated space for
struct work_struct and then cast it to struct delayed_work and passed
it into delayed_work functions - truly awesome engineering tradeoff to
save some bytes.
Xiaotian fixed it by making megraid allocate full delayed_work for
now. It should be converted to use work_struct and cancel_work_sync()
but I think we better do that after 3.7.
I added another commit to change BUG_ON()s in __queue_delayed_work()
to WARN_ON_ONCE()s so that the kernel doesn't crash even if there are
more such abuses."
* 'for-3.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: convert BUG_ON()s in __queue_delayed_work() to WARN_ON_ONCE()s
megaraid: fix BUG_ON() from incorrect use of delayed work
|
|
megaraid use INIT_WORK to declare a hotplug_work, but cast the
hotplug_work from work_struct to delayed_work and
schedule_delayed_work on it. This is very dangerous, as other part of
delayed_work might be kernel memories allocated by others.
With commit 8852aac ("workqueue: mod_delayed_work_on() shouldn't queue
timer on 0 delay"), schedule_delayed_work() will check dwork->timer
before queue_work even when @delay is 0, this causes megaraid code to
hit the BUG_ON() in workqueue code. Change megaraid code to use
delayed work.
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Neela Syam Kolli <megaraidlinux@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-scsi@vger.kernel.org
|
|
As ubi_self_check_all_ff() might sleep we are not allowed
to call it from atomic context.
For now we call it only from ubi_wl_get_peb().
There are some code paths where it would also make sense,
but these paths are currently atomic and only enabled
when fastmap is used.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
If UBI is built without fastmap, get_peb_for_wl() has to
remove the PEB manially from the free tree.
Otherwise the requested PEB lives in two trees.
Reported-by: Zach Sadecki <zsadecki@itwatchdogs.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Use for_each_pci_dev to simplify the code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
[Boris: cleanup comments and drop loop brackets]
Signed-off-by: Borislav Petkov <bp@alien8.de>
|
|
Pull EDAC fixes from Mauro Carvalho Chehab:
"One EDAC core fix, and a few driver fixes (i7300, i9275x, i7core)."
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
i7core_edac: fix panic when accessing sysfs files
i7300_edac: Fix error flag testing
edac: Fix the dimm filling for csrows-based layouts
i82975x_edac: Fix dimm label initialization
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some driver fixes for s5p/exynos (mostly race fixes)"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] s5p-mfc: Handle multi-frame input buffer
[media] s5p-mfc: Bug fix of timestamp/timecode copy mechanism
[media] exynos-gsc: Add missing video device vfl_dir flag initialization
[media] exynos-gsc: Fix settings for input and output image RGB type
[media] exynos-gsc: Don't use mutex_lock_interruptible() in device release()
[media] fimc-lite: Don't use mutex_lock_interruptible() in device release()
[media] s5p-fimc: Don't use mutex_lock_interruptible() in device release()
[media] s5p-fimc: Prevent race conditions during subdevs registration
|
|
Merge 'block-dev' branch.
I was going to just mark everything here for stable and leave it to the
3.8 merge window, but having decided on doing another -rc, I migth as
well merge it now.
This removes the bd_block_size_semaphore semaphore that was added in
this release to fix a race condition between block size changes and
block IO, and replaces it with atomicity guaratees in fs/buffer.c
instead, along with simplifying fs/block-dev.c.
This removes more lines than it adds, makes the code generally simpler,
and avoids the latency/rt issues that the block size semaphore
introduced for mount.
I'm not happy with the timing, but it wouldn't be much better doing this
during the merge window and then having some delayed back-port of it
into stable.
* block-dev:
blkdev_max_block: make private to fs/buffer.c
direct-io: don't read inode->i_blkbits multiple times
blockdev: remove bd_block_size_semaphore again
fs/buffer.c: make block-size be per-page and protected by the page lock
|
|
Pull networking fixes from David Miller:
1) 8139cp leaks memory in error paths, from Francois Romieu.
2) do_tcp_sendpages() cannot handle order > 0 pages, but they can
certainly arrive there now, fix from Eric Dumazet.
3) Race condition and sysfs fixes in bonding from Nikolay Aleksandrov.
4) Remain-on-Channel fix in mac80211 from Felix Liao.
5) CCK rate calculation fix in iwlwifi, from Emmanuel Grumbach.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
8139cp: fix coherent mapping leak in error path.
tcp: fix crashes in do_tcp_sendpages()
bonding: fix race condition in bonding_store_slaves_active
bonding: make arp_ip_target parameter checks consistent with sysfs
bonding: fix miimon and arp_interval delayed work race conditions
mac80211: fix remain-on-channel (non-)cancelling
iwlwifi: fix the basic CCK rates calculation
|
