| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 1cc3542c76acb5f59001e3e562eba672f1983355 upstream.
In the hardware implementation of the I2C HID driver based on DesignWare
GPIO IRQ chip, when the user continues to use the I2C HID device in the
suspend process, the I2C HID interrupt will be masked after the resume
process is finished.
This is because the disable_irq()/enable_irq() of the DesignWare GPIO
driver does not synchronize the IRQ mask register state. In normal use
of the I2C HID procedure, the GPIO IRQ irq_mask()/irq_unmask() functions
are called in pairs. In case of an exception, i2c_hid_core_suspend()
calls disable_irq() to disable the GPIO IRQ. With low probability, this
causes irq_unmask() to not be called, which causes the GPIO IRQ to be
masked and not unmasked in enable_irq(), raising an exception.
Add synchronization to the masked register state in the
dwapb_irq_enable()/dwapb_irq_disable() function. mask the GPIO IRQ
before disabling it. After enabling the GPIO IRQ, unmask the IRQ.
Fixes: 7779b3455697 ("gpio: add a driver for the Synopsys DesignWare APB GPIO block")
Cc: stable@kernel.org
Co-developed-by: Riwen Lu <luriwen@kylinos.cn>
Signed-off-by: Riwen Lu <luriwen@kylinos.cn>
Signed-off-by: xiongxin <xiongxin@kylinos.cn>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f71f6ff8c1f682a1cae4e8d7bdeed9d7f76b8f75 upstream.
Commit 34539b442b3b ("bus: ti-sysc: Flush posted write on enable before
reset") caused a regression reproducable on omap4 duovero where the ISS
target module can produce interconnect errors on boot. Turns out the
registers are not accessible until after a delay for devices needing
a ti,sysc-delay-us value.
Let's fix this by flushing the posted write only after the reset delay.
We do flushing also for ti,sysc-delay-us using devices as that should
trigger an interconnect error if the delay is not properly configured.
Let's also add some comments while at it.
Fixes: 34539b442b3b ("bus: ti-sysc: Flush posted write on enable before reset")
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5c584f175d32f9cc66c909f851cd905da58b39ea upstream.
The driver always registers pin configurations in device tree. This can
cause some inconvenience to users, as pin configurations in the base
device tree cannot be disabled in the device tree overlay, even when the
relevant devices are not used.
Ignore disabled pin configuration nodes in device tree.
Fixes: ec648f6b7686 ("pinctrl: starfive: Add pinctrl driver for StarFive SoCs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Link: https://lore.kernel.org/r/fe4c15dcc3074412326b8dc296b0cbccf79c49bf.1701422582.git.namcao@linutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f6e3b40a2c89c1d832ed9cb031dc9825bbf43b7c upstream.
The driver always registers pin configurations in device tree. This can
cause some inconvenience to users, as pin configurations in the base
device tree cannot be disabled in the device tree overlay, even when the
relevant devices are not used.
Ignore disabled pin configuration nodes in device tree.
Fixes: 447976ab62c5 ("pinctrl: starfive: Add StarFive JH7110 sys controller driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Link: https://lore.kernel.org/r/fd8bf044799ae50a6291ae150ef87b4f1923cacb.1701422582.git.namcao@linutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b86f4b790c998afdbc88fe1aa55cfe89c4068726 upstream.
__bio_for_each_segment assumes that the first struct bio_vec argument
doesn't change - it calls "bio_advance_iter_single((bio), &(iter),
(bvl).bv_len)" to advance the iterator. Unfortunately, the dm-integrity
code changes the bio_vec with "bv.bv_len -= pos". When this code path
is taken, the iterator would be out of sync and dm-integrity would
report errors. This happens if the machine is out of memory and
"kmalloc" fails.
Fix this bug by making a copy of "bv" and changing the copy instead.
Fixes: 7eada909bfd7 ("dm: add integrity target")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 066c5b46b6eaf2f13f80c19500dbb3b84baabb33 upstream.
In commit 8930a6c20791 ("scsi: core: add support for request batching") the
block layer bd->last flag was mapped to SCMD_LAST and used as an indicator
to send the batch for the drivers that implement this feature. However, the
error handling code was not updated accordingly.
scsi_send_eh_cmnd() is used to send error handling commands and request
sense. The problem is that request sense comes as a single command that
gets into the batch queue and times out. As a result the device goes
offline after several failed resets. This was observed on virtio_scsi
during a device resize operation.
[ 496.316946] sd 0:0:4:0: [sdd] tag#117 scsi_eh_0: requesting sense
[ 506.786356] sd 0:0:4:0: [sdd] tag#117 scsi_send_eh_cmnd timeleft: 0
[ 506.787981] sd 0:0:4:0: [sdd] tag#117 abort
To fix this always set SCMD_LAST flag in scsi_send_eh_cmnd() and
scsi_reset_ioctl().
Fixes: 8930a6c20791 ("scsi: core: add support for request batching")
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexander Atanasov <alexander.atanasov@virtuozzo.com>
Link: https://lore.kernel.org/r/20231215121008.2881653-1-alexander.atanasov@virtuozzo.com
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c5becf57dd5659c687d41d623a69f42d63f59eb2 upstream.
This reverts commit 9dc704dcc09eae7d21b5da0615eb2ed79278f63e.
Several reports have been made indicating that this commit caused
hangs. Numerous attempts at root causing and fixing the issue have
been unsuccessful so let's revert for now.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217599
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1e37bf84afacd5ba17b7a13a18ca2bc78aff05c0 upstream.
This driver uses MMIO access for reading NVRAM from a flash device.
Underneath there is a flash controller that reads data and provides
mapping window.
Using MMIO interface affects controller configuration and may break real
controller driver. It was reported by multiple users of devices with
NVRAM stored on NAND.
Modify driver to read & cache NVRAM content during init and use that
copy to provide NVMEM data when requested. On NAND flashes due to their
alignment NVRAM partitions can be quite big (1 MiB and more) while
actual NVRAM content stays quite small (usually 16 to 32 KiB). To avoid
allocating so much memory check for actual data length.
Link: https://lore.kernel.org/linux-mtd/CACna6rwf3_9QVjYcM+847biTX=K0EoWXuXcSMkJO1Vy_5vmVqA@mail.gmail.com/
Fixes: 3fef9ed0627a ("nvmem: brcm_nvram: new driver exposing Broadcom's NVRAM")
Cc: <Stable@vger.kernel.org>
Cc: Arınç ÜNAL <arinc.unal@arinc9.com>
Cc: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231215111358.316727-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fc70d643a2f6678cbe0f5c86433c1aeb4d613fcc upstream.
The current Atmel SPI controller driver (v2) behaves incorrectly when
using two SPI devices with different clock polarities and GPIO CS.
When switching from one device to another, the controller driver first
enables the CS and then applies whatever configuration suits the targeted
device (typically, the polarities). The side effect of such order is the
apparition of a spurious clock edge after enabling the CS when the clock
polarity needs to be inverted wrt. the previous configuration of the
controller.
This parasitic clock edge is problematic when the SPI device uses that edge
for internal processing, which is perfectly legitimate given that its CS
was asserted. Indeed, devices such as HVS8080 driven by driver gpio-sr in
the kernel are shift registers and will process this first clock edge to
perform a first register shift. In this case, the first bit gets lost and
the whole data block that will later be read by the kernel is all shifted
by one.
Current behavior:
The actual switching of the clock polarity only occurs after the CS
when the controller sends the first message:
CLK ------------\ /-\ /-\
| | | | | . . .
\---/ \-/ \
CS -----\
|
\------------------
^ ^ ^
| | |
| | Actual clock of the message sent
| |
| Change of clock polarity, which occurs with the first
| write to the bus. This edge occurs when the CS is
| already asserted, and can be interpreted as
| the first clock edge by the receiver.
|
GPIO CS toggle
This issue is specific to this controller because while the SPI core
performs the operations in the right order, the controller however does
not. In practice, the controller only applies the clock configuration right
before the first transmission.
So this is not a problem when using the controller's dedicated CS, as the
controller does things correctly, but it becomes a problem when you need to
change the clock polarity and use an external GPIO for the CS.
One possible approach to solve this problem is to send a dummy message
before actually activating the CS, so that the controller applies the clock
polarity beforehand.
New behavior:
CLK ------\ /-\ /-\ /-\ /-\
| | | ... | | | | ... | |
\------/ \- -/ \------/ \- -/ \------
CS -\/-----------------------\
|| |
\/ \---------------------
^ ^ ^ ^ ^
| | | | |
| | | | Expected clock cycles when
| | | | sending the message
| | | |
| | | Actual GPIO CS activation, occurs inside
| | | the driver
| | |
| | Dummy message, to trigger clock polarity
| | reconfiguration. This message is not received and
| | processed by the device because CS is low.
| |
| Change of clock polarity, forced by the dummy message. This
| time, the edge is not detected by the receiver.
|
This small spike in CS activation is due to the fact that the
spi-core activates the CS gpio before calling the driver's
set_cs callback, which deactivates this gpio again until the
clock polarity is correct.
To avoid having to systematically send a dummy packet, the driver keeps
track of the clock's current polarity. In this way, it only sends the dummy
packet when necessary, ensuring that the clock will have the correct
polarity when the CS is toggled.
There could be two hardware problems with this patch:
1- Maybe the small CS activation peak can confuse SPI devices
2- If on a design, a single wire is used to select two devices depending
on its state, the dummy message may disturb them.
Fixes: 5ee36c989831 ("spi: atmel_spi update chipselect handling")
Cc: <stable@vger.kernel.org>
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
Link: https://msgid.link/r/20231204154903.11607-1-louis.chauvet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 890188d2d7e4ac6c131ba166ca116cb315e752ee upstream.
Upstream commit e0205d6203c2 ("spi: atmel: Prevent false timeouts on
long transfers") has tried to mitigate the problem of getting spi
transfers canceled because they were lasting too long. On slow buses,
transfers in the MiB range can take more than one second and thus a
calculation was added to progressively increment the timeout value. In
order to not be too problematic from a user point of view (waiting dozen
of seconds or even minutes), the wait call was turned interruptible.
Turning the wait interruptible was a mistake as what we really wanted to
do was to be able to kill a transfer. Any signal interrupting our
transfer would not be suitable at all so a second attempt was made at
turning the wait killable instead.
Link: https://lore.kernel.org/linux-spi/20231127095842.389631-1-miquel.raynal@bootlin.com/
All being well, it was reported that JFFS2 was showing a splat when
interrupting a transfer. After some more debate about whether JFFS2
should be fixed and how, it was also pointed out that the whole
consistency of the filesystem in case of parallel I/O would be
compromised. Changing JFFS2 behavior would in theory be possible but
nobody has the energy and time and knowledge to do this now, so better
prevent spi transfers to be interrupted by the user.
Partially revert the blamed commit to no longer use the interruptible
nor the killable variant of wait_for_completion().
Fixes: e0205d6203c2 ("spi: atmel: Prevent false timeouts on long transfers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Ronald Wahl <ronald.wahl@raritan.com>
Link: https://lore.kernel.org/r/20231205083102.16946-1-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1ca2761a7734928ffe0678f88789266cf3d05362 upstream.
The intended move from wait_for_completion_*() to
wait_for_completion_interruptible_*() was to allow (very) long spi memory
transfers to be stopped upon user request instead of freezing the
machine forever as the timeout value could now be significantly bigger.
However, depending on the user logic, applications can receive many
signals for their own "internal" purpose and have nothing to do with the
requested kernel operations, hence interrupting spi transfers upon any
signal is probably not a wise choice. Instead, let's switch to
wait_for_completion_killable_*() to only catch the "important"
signals. This was likely the intended behavior anyway.
Fixes: e0205d6203c2 ("spi: atmel: Prevent false timeouts on long transfers")
Cc: stable@vger.kernel.org
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231127095842.389631-1-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 49e0a85ec3441edc6c77aa40206d6e5ee4597efc upstream.
The pipe DMC seems to be making a mess of things in ADL. Various weird
symptoms have been observed such as missing vblank irqs, typicalle
happening when using multiple displays.
Keep all pipe DMC event handlers disabled until needed (which is never
atm). This is also what Windows does on ADL+.
We can also drop DG2 from disable_all_flip_queue_events() since
on DG2 the pipe DMC is the one that handles the flip queue events.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8685
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231211213750.27109-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
(cherry picked from commit 648d7be8ecf47b0556e32550145c70db153b16fb)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 88a173e5dd05e788068e8fa20a8c37c44bd8f416 upstream.
Currently async flips are busted when bigjoiner is in use.
As a short term fix simply reject async flips in that case.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9769
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231211081134.2698-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit e93bffc2ac0a833b42841f31fff955549d38ce98)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bd7f77dae69532ffc027ee50ff99e3792dc30b7f upstream.
The driver should continue get the timestamp if STMMAC_FLAG_EXT_SNAPSHOT_EN
flag is set.
Fixes: aa5513f5d95f ("net: stmmac: replace the ext_snapshot_en field with a flag")
Cc: <stable@vger.kernel.org> # 6.6
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Lai Peter Jun Ann <jun.ann.lai@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3dc5d44545453de1de9c53cc529cc960a85933da upstream.
There is a bug in the ks8851 Ethernet driver that more data is written
to the hardware TX buffer than actually available. This is caused by
wrong accounting of the free TX buffer space.
The driver maintains a tx_space variable that represents the TX buffer
space that is deemed to be free. The ks8851_start_xmit_spi() function
adds an SKB to a queue if tx_space is large enough and reduces tx_space
by the amount of buffer space it will later need in the TX buffer and
then schedules a work item. If there is not enough space then the TX
queue is stopped.
The worker function ks8851_tx_work() dequeues all the SKBs and writes
the data into the hardware TX buffer. The last packet will trigger an
interrupt after it was send. Here it is assumed that all data fits into
the TX buffer.
In the interrupt routine (which runs asynchronously because it is a
threaded interrupt) tx_space is updated with the current value from the
hardware. Also the TX queue is woken up again.
Now it could happen that after data was sent to the hardware and before
handling the TX interrupt new data is queued in ks8851_start_xmit_spi()
when the TX buffer space had still some space left. When the interrupt
is actually handled tx_space is updated from the hardware but now we
already have new SKBs queued that have not been written to the hardware
TX buffer yet. Since tx_space has been overwritten by the value from the
hardware the space is not accounted for.
Now we have more data queued then buffer space available in the hardware
and ks8851_tx_work() will potentially overrun the hardware TX buffer. In
many cases it will still work because often the buffer is written out
fast enough so that no overrun occurs but for example if the peer
throttles us via flow control then an overrun may happen.
This can be fixed in different ways. The most simple way would be to set
tx_space to 0 before writing data to the hardware TX buffer preventing
the queuing of more SKBs until the TX interrupt has been handled. I have
chosen a slightly more efficient (and still rather simple) way and
track the amount of data that is already queued and not yet written to
the hardware. When new SKBs are to be queued the already queued amount
of data is honoured when checking free TX buffer space.
I tested this with a setup of two linked KS8851 running iperf3 between
the two in bidirectional mode. Before the fix I got a stall after some
minutes. With the fix I saw now issues anymore after hours.
Fixes: 3ba81f3ece3c ("net: Micrel KS8851 SPI network driver")
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org # 5.10+
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231214181112.76052-1-rwahl@gmx.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ea3715941a9b7d816a1e9096ac0577900af2a69e upstream.
This add a mapping for the airplane mode button on the TUXEDO Pulse Gen3.
While it is physically a key it behaves more like a switch, sending a key
down on first press and a key up on 2nd press. Therefor the switch event
is used here. Besides this behaviour it uses the HID usage-id 0xc6
(Wireless Radio Button) and not 0xc8 (Wireless Radio Slider Switch), but
since neither 0xc6 nor 0xc8 are currently implemented at all in
soc_button_array this not to standard behaviour is not put behind a quirk
for the moment.
Signed-off-by: Christoffer Sandberg <cs@tuxedo.de>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Link: https://lore.kernel.org/r/20231215171718.80229-1-wse@tuxedocomputers.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aef05e349bfd81c95adb4489639413fadbb74a83 upstream.
When the device is disconnected we get the following messages showing
failed operations:
Nov 28 20:22:11 localhost kernel: usb 2-3: USB disconnect, device number 2
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3: unregister 'ax88179_178a' usb-0000:02:00.0-3, ASIX AX88179 USB 3.0 Gigabit Ethernet
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3: Failed to read reg index 0x0002: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3: Failed to write reg index 0x0002: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3 (unregistered): Failed to write reg index 0x0002: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3 (unregistered): Failed to write reg index 0x0001: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3 (unregistered): Failed to write reg index 0x0002: -19
The reason is that although the device is detached, normal stop and
unbind operations are commanded from the driver. These operations are
not necessary in this situation, so avoid these logs when the device is
detached if the result of the operation is -ENODEV and if the new flag
informing about the disconnecting status is enabled.
cc: <stable@vger.kernel.org>
Fixes: e2ca90c276e1f ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231207175007.263907-1-jtornosm@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7fbcd195e2b8cc952e4aeaeb50867b798040314c upstream.
Here "temp" is the number of characters that we have written and "size"
is the size of the buffer. The intent was clearly to say that if we have
written to the end of the buffer then stop.
However, for that to work the comparison should have been done on the
original "size" value instead of the "size -= temp" value. Not only
will that not trigger when we want to, but there is a small chance that
it will trigger incorrectly before we want it to and we break from the
loop slightly earlier than intended.
This code was recently changed from using snprintf() to scnprintf(). With
snprintf() we likely would have continued looping and passed a negative
size parameter to snprintf(). This would have triggered an annoying
WARN(). Now that we have converted to scnprintf() "size" will never
drop below 1 and there is no real need for this test. We could change
the condition to "if (temp <= 1) goto done;" but just deleting the test
is cleanest.
Fixes: 7d50195f6c50 ("usb: host: Faraday fotg210-hcd driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/ZXmwIwHe35wGfgzu@suswa
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c994cb596bf7ef5928f06331c76f46e071b16f09 upstream.
Fix the recently added connector sanity check which was off by one and
prevented orientation notifications from being handled correctly for the
second port when using GPIOs to determine orientation.
Fixes: c6165ed2f425 ("usb: ucsi: glink: use the connector orientation GPIO to provide switch events")
Cc: stable <stable@kernel.org>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231208123603.29957-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 06f22cd6635bdae7d73566fca9879b2026a08e00 upstream.
Add support for Quectel RM500Q R13 firmware which uses Prot=40 for the
NMEA port:
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 8 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=2c7c ProdID=0800 Rev= 4.14
S: Manufacturer=Quectel
S: Product=RM500Q-AE
S: SerialNumber=xxxxxxxx
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=896mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 13fde9ac23ca8c6d1ac13cc9eefe1f1ac3ee30a4 upstream.
This ID was added based on latest SDX12 code base line, and we
made some changes with previous 0489:e0db.
Test evidence as below:
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs= 2
P: Vendor=0489 ProdID=e0da Rev=05.04
S: Manufacturer=Qualcomm
S: Product=Qualcomm Snapdragon X12
S: SerialNumber=2bda65fb
C: #Ifs= 6 Cfg#= 2 Atr=a0 MxPwr=896mA
I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I: If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
0&1: MBIM, 2: Modem, 3:GNSS, 4:Diag, 5:ADB
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6d79d9434c69bb8ffa8a631050eb0ad6b83d3e90 upstream.
Add Quectel EG912Y "DIAG, AT, MODEM"
0x6001: ECM / RNDIS + DIAG + AT + MODEM
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=6001 Rev= 3.18
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=0000
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=4096ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=4096ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=88(I) Atr=03(Int.) MxPS= 64 Ivl=4096ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Alper Ak <alperyasinak1@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 513d88a88e0203188a38f4647dd08170aebd85df upstream.
Update the constant names for unused USB PIDs (product identifiers) to
reflect the new products now using the PIDs.
Signed-off-by: Mark Glover <mark.glover@actisense.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cd607f2cbbbec90682b2f6d6b85e1525d0f43b19 upstream.
If WED rx is enabled, rx buffers are added to a buffer pool that can be
filled from multiple page pools. Because buffers freed from rx poll are
not guaranteed to belong to the processed queue's page pool, lockless
caching must not be used in this case.
Cc: stable@vger.kernel.org
Fixes: 2f5c3c77fc9b ("wifi: mt76: switch to page_pool allocator")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231208075004.69843-1-nbd@nbd.name
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 772685c14743ad565bb271041ad3c262298cd6fc upstream.
This flash drive reports write protect during the first mode sense.
In the past this was not an issue as the kernel called revalidate twice,
thus asking the device for its write protect status twice, with write
protect being disabled in the second mode sense.
However, since commit 1e029397d12f ("scsi: sd: Reorganize DIF/DIX code to
avoid calling revalidate twice") that is no longer the case, thus the
device shows up read only.
[490891.289495] sd 12:0:0:0: [sdl] Write Protect is on
[490891.289497] sd 12:0:0:0: [sdl] Mode Sense: 2b 00 80 08
This does not appear to be a timing issue, as enabling the usbcore quirk
USB_QUIRK_DELAY_INIT has no effect on write protect.
Fixes: 1e029397d12f ("scsi: sd: Reorganize DIF/DIX code to avoid calling revalidate twice")
Cc: stable <stable@kernel.org>
Signed-off-by: Tasos Sahanidis <tasos@tasossah.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20231207134441.298131-1-tasos@tasossah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bce61476dc82f114e24e9c2e11fb064781ec563c upstream.
Commit ee708e6baacd ("iio: buffer: introduce support for attaching more
IIO buffers") introduced support for multiple buffers per indio_dev but
left indio_dev->buffer for a few legacy use cases.
In the case of the triggered buffer, iio_triggered_buffer_cleanup()
still assumes that indio_dev->buffer points to the buffer allocated by
iio_triggered_buffer_setup_ext(). However, since
iio_triggered_buffer_setup_ext() now calls iio_device_attach_buffer()
to attach the buffer, indio_dev->buffer will only point to the buffer
allocated by iio_device_attach_buffer() if it the first buffer attached.
This adds a check to make sure that no other buffer has been attached
yet to ensure that indio_dev->buffer will be assigned when
iio_device_attach_buffer() is called.
As per discussion in the review thread, we may want to deal with multiple
triggers per device, but this is a fix for the issue in the meantime and
any such support would be unlikely to be suitable for a backport.
Fixes: ee708e6baacd ("iio: buffer: introduce support for attaching more IIO buffers")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Acked-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20231031210521.1661552-1-dlechner@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3b8157ec4573e304a29b7bced627e144dbc3dfdb upstream.
The current offset has the scale already applied to it. The ABI
documentation defines the offset parameter as "offset to be added
to <type>[Y]_raw prior to scaling by <type>[Y]_scale in order to
obtain value in the <type> units as specified in <type>[Y]_raw
documentation"
The right value is obtained at 0 degrees Celsius by the formula provided
in the datasheet:
T = Tsens_t0 + (Tadc_t - Tadc_t0) / Tadc_res
where:
T = 0 degrees Celsius
Tsens_t0 (reference temperature) = 25 degrees Celsius
Tadc_t0 (16-bit format for Tsens_t0) = 17508
Tadc_res = 60.1 LSB/degree Celsius
The resulting offset is 16005.5, which has been truncated to 16005 to
provide an integer value with a precision loss smaller than the 1-LSB
measurement precision.
Fix the offset to apply its value prior to scaling.
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/9879beec-05fc-4fc6-af62-d771e238954e@wolfvision.net
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 60576e84c187043cef11f11d015249e71151d35a upstream.
Fix wrong handling of a DMA request where the probing only failed
if -EPROPE_DEFER was returned. Instead, let us fail if a non -ENODEV
value is returned. This makes DMAs explicitly optional. Even if the
DMA request is unsuccessfully, the ADC can still work properly.
We do also handle the defer probe case by making use of dev_err_probe().
Fixes: f438b9da75eb ("drivers: iio: ti_am335x_adc: add dma support")
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20230925134427.214556-1-w.egorov@phytec.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ee4d79055aeea27f1b8c42233cc0c90d0a8b5355 upstream.
This prevents the warning message "SPI driver has no spi_device_id for..."
when registering the driver. More importantly, it makes sure that
module autoloading works as spi relies on spi: modaliases and not of.
While at it, move the of_device_id table to it's natural place.
Fixes: fff7352bf7a3c ("iio: imu: Add support for adis16475")
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20231102125258.3284830-1-nuno.sa@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 54cf39ec16335dadbe1ba008d8e5e98dae3e26f8 upstream.
The HTU21 offers 4 sampling frequencies: 20, 40, 70 and 120, which are
associated to an index that is used to select the right measurement
resolution and its corresponding measurement time. The current
implementation selects the measurement resolution and the temperature
measurement time properly, but it does not select the right humidity
measurement time in all cases.
In summary, the 40 and 70 humidity measurement times are swapped.
The reason for that is probably the unusual coding for the measurement
resolution. According to the datasheet, the bits [7,0] of the "user
register" are used as follows to select the bit resolution:
--------------------------------------------------
| Bit 7 | Bit 0 | RH | Temp | Trh (us) | Tt (us) |
--------------------------------------------------
| 0 | 0 | 12 | 14 | 16000 | 50000 |
--------------------------------------------------
| 0 | 1 | 8 | 12 | 3000 | 13000 |
--------------------------------------------------
| 1 | 0 | 10 | 13 | 5000 | 25000 |
--------------------------------------------------
| 1 | 1 | 11 | 11 | 8000 | 7000 |
--------------------------------------------------
*This table is available in the official datasheet, page 13/21. I have
just appended the times provided in the humidity/temperature tables,
pages 3/21, 5/21. Note that always a pair of resolutions is selected.
The sampling frequencies [20, 40, 70, 120] are assigned to a linear
index [0..3] which is then coded as follows [1]:
Index [7,0]
--------------
idx 0 0,0
idx 1 1,0
idx 2 0,1
idx 3 1,1
That is done that way because the temperature measurements are being
used as the reference for the sampling frequency (the frequencies and
the temperature measurement times are correlated), so increasing the
index always reduces the temperature measurement time and its
resolution. Therefore, the temperature measurement time array is as
simple as [50000, 25000, 13000, 7000]
On the other hand, the humidity resolution cannot follow the same
pattern because of the way it is coded in the "user register", where
both resolutions are selected at the same time. The humidity measurement
time array is the following: [16000, 3000, 5000, 8000], which defines
the following assignments:
Index [7,0] Trh
-----------------------
idx 0 0,0 16000 -> right, [0,0] selects 12 bits (Trh = 16000)
idx 1 1,0 3000 -> wrong! [1,0] selects 10 bits (Trh = 5000)
idx 2 0,1 5000 -> wrong! [0,1] selects 8 bits (Trh = 3000)
idx 3 1,1 8000 -> right, [1,1] selects 11 bits (Trh = 8000)
The times have been ordered as if idx = 1 -> [0,1] and idx = 2 -> [1,0],
which is not the case for the reason explained above.
So a simple modification is required to obtain the right humidity
measurement time array, swapping the values in the positions 1 and 2.
The right table should be the following: [16000, 5000, 3000, 8000]
Fix the humidity measurement time array with the right idex/value
coding.
[1] The actual code that makes this coding and assigns it to the current
value of the "user register" is the following:
config_reg &= 0x7E;
config_reg |= ((i & 1) << 7) + ((i & 2) >> 1);
Fixes: d574a87cc311 ("Add meas-spec sensors common part")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20231026-topic-htu21_conversion_time-v1-1-bd257dc44209@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2475ecdb9b6e177b133cf26e64e8d441d37bebde upstream.
According to the spec, this ADC totally support 8 channels.
i.MX93 contain this ADC with 4 channels connected to pins in
the package. i.MX95 contain this ADC with 8 channels connected
to pins in the package.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Fixes: 7d02296ac8b8 ("iio: adc: add imx93 adc support")
Link: https://lore.kernel.org/r/20231116071026.611269-1-haibo.chen@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 92bfa4ab1b79be95c4f52d13f5386390f0a513c2 upstream.
The IIO ABI mandates acceleration values from accelerometer to be
emitted in m/s^2. The KX022A was emitting values in micro m/s^2.
Fix driver to report the correct scale values.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reported-by: Jagath Jog J <jagathjog1996@gmail.com>
Fixes: 7c1d1677b322 ("iio: accel: Support Kionix/ROHM KX022A accelerometer")
Tested-by: Jagath Jog J <jagathjog1996@gmail.com>
Link: https://lore.kernel.org/r/ZTEt7NqfDHPOkm8j@dc78bmyyyyyyyyyyyyydt-3.rev.dnainternet.fi
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 04c116e2bdfc3969f9819d2cebfdf678353c354c ]
When accessing sq_tail_slot without protection from sq_lock, a race
condition can cause multiple SQEs to be copied to duplicate SQE slots. This
can lead to multiple stability issues. Fix this by moving the *dest
initialization in ufshcd_send_command() back under protection from the
sq_lock.
Fixes: 3c85f087faec ("scsi: ufs: mcq: Use pointer arithmetic in ufshcd_send_command()")
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1702913550-20631-1-git-send-email-quic_cang@quicinc.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
ufs_qcom_clk_scale_notify()
[ Upstream commit 9264fd61e628ce180a168e6b90bde134dd49ec28 ]
In commit 031312dbc695 ("scsi: ufs: ufs-qcom: Remove unnecessary goto
statements") the error handling was accidentally changed, resulting in the
error of ufs_qcom_clk_scale_*() calls not being returned.
This is the case I checked:
ufs_qcom_clk_scale_notify ->
'ufs_qcom_clk_scale_up_/down_pre_change' error ->
return 0;
Make sure those errors are properly returned.
Fixes: 031312dbc695 ("scsi: ufs: ufs-qcom: Remove unnecessary goto statements")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Link: https://lore.kernel.org/r/20231215003812.29650-1-cw9316.lee@samsung.com
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 08c94d80b2da481652fb633e79cbc41e9e326a91 ]
skb_share_check() already drops the reference to the skb when returning
NULL. Using kfree_skb() in the error handling path leads to an skb double
free.
Fix this by removing the variable tmp_skb, and return directly when
skb_share_check() returns NULL.
Fixes: 01a4cc4d0cd6 ("bnx2fc: do not add shared skbs to the fcoe_rx_list")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20221114110626.526643-1-weiyongjun@huaweicloud.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 59b75dcb0953813676b5030877f3f37cedaed87d ]
According to Amlogic custom kernels ADC of axg SoC family has
vref_select and requires this setting to work nominally and thus
needs a separate config.
Fixes: 90c6241860bf ("iio: adc: meson: init voltage control bits")
Signed-off-by: George Stark <gnstark@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231127235558.71995-1-gnstark@salutedevices.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 59b6a747e2d39227ac2325c5e29d6ab3bb070c2a ]
Check the return value of i2c_add_adapter. Static analysis revealed that
the function did not properly handle potential failures of
i2c_add_adapter, which could lead to partial initialization of the I2C
adapter and unstable operation.
Signed-off-by: Haoran Liu <liuhaoran14@163.com>
Link: https://lore.kernel.org/r/20231203164653.38983-1-liuhaoran14@163.com
Fixes: d7535ffa427b ("Input: driver for microcontroller keys on the iPaq h3xxx")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bfc7db1cb94ad664546d70212699f8cc6c539e8c ]
Add the generic icc sync_state callback to ensure interconnect votes
are taken into account, instead of being pegged at maximum values.
Fixes: b95b668eaaa2 ("interconnect: qcom: icc-rpmh: Add BCMs to commit list in pre_aggregate")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231130-topic-8250icc_syncstate-v1-1-7ce78ba6e04c@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c3df0e29fb7788c4b3ddf37d5ed87dda2b822943 ]
inv_mpu6050_sensor_show() can return -EINVAL or IIO_VAL_INT. Return the
true value rather than only return IIO_VAL_INT.
Fixes: d5098447147c ("iio: imu: mpu6050: add calibration offset support")
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20231030020218.65728-1-suhui@nfschina.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ad2ab1297d0c80899125a842bb7a078abfe1e6ce ]
Currently, if provider->xlate() or provider->xlate_extended()
"successfully" return a NULL node, then of_icc_get_from_provider() won't
consider that an error and will successfully return the NULL node. This
bypasses error handling in of_icc_get_by_index() and leads to NULL
dereferences in path_find().
This could be avoided by ensuring provider callbacks always return an
error for NULL nodes, but it's better to explicitly protect against this
in the common framework.
Fixes: 87e3031b6fbd ("interconnect: Allow endpoints translation via DT")
Signed-off-by: Mike Tipton <quic_mdtipton@quicinc.com>
Link: https://lore.kernel.org/r/20231025145829.11603-1-quic_mdtipton@quicinc.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f6fe0b2d35457c10ec37acc209d19726bdc16dbd ]
the nvme_handle_cqe() interrupt handler calls nvme_complete_async_event()
but the latter may call nvme_auth_stop() which is a blocking function.
Sleeping functions can't be called in interrupt context
BUG: sleeping function called from invalid context
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 0, name: swapper/15
Call Trace:
<IRQ>
__cancel_work_timer+0x31e/0x460
? nvme_change_ctrl_state+0xcf/0x3c0 [nvme_core]
? nvme_change_ctrl_state+0xcf/0x3c0 [nvme_core]
nvme_complete_async_event+0x365/0x480 [nvme_core]
nvme_poll_cq+0x262/0xe50 [nvme]
Fix the bug by moving nvme_auth_stop() to fw_act_work
(executed by the nvme_wq workqueue)
Fixes: f50fff73d620 ("nvme: implement In-Band authentication")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1d656bd259edb89dc1d9938ec5c5389867088546 ]
While the GPIO cdev gpio_ioctl() call is in progress, the kernel can
call gpiochip_remove() which will set gdev->chip to NULL, after which
any subsequent access will cause a crash.
gpio_ioctl() was overlooked by the previous fix to protect syscalls
(bdbbae241a04), so add protection for that.
Fixes: bdbbae241a04 ("gpiolib: protect the GPIO device against being dropped while in use by user-space")
Fixes: d7c51b47ac11 ("gpio: userspace ABI for reading/writing GPIO lines")
Fixes: 3c0d9c635ae2 ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL")
Fixes: aad955842d1c ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 14694179e561b5f2f7e56a0f590e2cb49a9cc7ab ]
Trying to suspend to RAM on SAMA5D27 EVK leads to the following lockdep
warning:
============================================
WARNING: possible recursive locking detected
6.7.0-rc5-wt+ #532 Not tainted
--------------------------------------------
sh/92 is trying to acquire lock:
c3cf306c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0xe8/0x100
but task is already holding lock:
c3d7c46c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0xe8/0x100
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&irq_desc_lock_class);
lock(&irq_desc_lock_class);
*** DEADLOCK ***
May be due to missing lock nesting notation
6 locks held by sh/92:
#0: c3aa0258 (sb_writers#6){.+.+}-{0:0}, at: ksys_write+0xd8/0x178
#1: c4c2df44 (&of->mutex){+.+.}-{3:3}, at: kernfs_fop_write_iter+0x138/0x284
#2: c32684a0 (kn->active){.+.+}-{0:0}, at: kernfs_fop_write_iter+0x148/0x284
#3: c232b6d4 (system_transition_mutex){+.+.}-{3:3}, at: pm_suspend+0x13c/0x4e8
#4: c387b088 (&dev->mutex){....}-{3:3}, at: __device_suspend+0x1e8/0x91c
#5: c3d7c46c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0xe8/0x100
stack backtrace:
CPU: 0 PID: 92 Comm: sh Not tainted 6.7.0-rc5-wt+ #532
Hardware name: Atmel SAMA5
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x48
dump_stack_lvl from __lock_acquire+0x19ec/0x3a0c
__lock_acquire from lock_acquire.part.0+0x124/0x2d0
lock_acquire.part.0 from _raw_spin_lock_irqsave+0x5c/0x78
_raw_spin_lock_irqsave from __irq_get_desc_lock+0xe8/0x100
__irq_get_desc_lock from irq_set_irq_wake+0xa8/0x204
irq_set_irq_wake from atmel_gpio_irq_set_wake+0x58/0xb4
atmel_gpio_irq_set_wake from irq_set_irq_wake+0x100/0x204
irq_set_irq_wake from gpio_keys_suspend+0xec/0x2b8
gpio_keys_suspend from dpm_run_callback+0xe4/0x248
dpm_run_callback from __device_suspend+0x234/0x91c
__device_suspend from dpm_suspend+0x224/0x43c
dpm_suspend from dpm_suspend_start+0x9c/0xa8
dpm_suspend_start from suspend_devices_and_enter+0x1e0/0xa84
suspend_devices_and_enter from pm_suspend+0x460/0x4e8
pm_suspend from state_store+0x78/0xe4
state_store from kernfs_fop_write_iter+0x1a0/0x284
kernfs_fop_write_iter from vfs_write+0x38c/0x6f4
vfs_write from ksys_write+0xd8/0x178
ksys_write from ret_fast_syscall+0x0/0x1c
Exception stack(0xc52b3fa8 to 0xc52b3ff0)
3fa0: 00000004 005a0ae8 00000001 005a0ae8 00000004 00000001
3fc0: 00000004 005a0ae8 00000001 00000004 00000004 b6c616c0 00000020 0059d190
3fe0: 00000004 b6c61678 aec5a041 aebf1a26
This warning is raised because pinctrl-at91-pio4 uses chained IRQ. Whenever
a wake up source configures an IRQ through irq_set_irq_wake, it will
lock the corresponding IRQ desc, and then call irq_set_irq_wake on "parent"
IRQ which will do the same on its own IRQ desc, but since those two locks
share the same class, lockdep reports this as an issue.
Fix lockdep false positive by setting a different class for parent and
children IRQ
Fixes: 776180848b57 ("pinctrl: introduce driver for Atmel PIO4 controller")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Link: https://lore.kernel.org/r/20231215-lockdep_warning-v1-1-8137b2510ed5@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b4cc1cbba5195a4dd497cf2f8f09e7807977d543 ]
Some masters may drive the transfers with low enough latency between
the nak/stop phase of the current command and the start/address phase
of the following command that the interrupts are coalesced by the
time we process them.
Handle the stop conditions before processing SLAVE_MATCH to fix the
complaints that sometimes occur below.
"aspeed-i2c-bus 1e78a040.i2c-bus: irq handled != irq. Expected
0x00000086, but was 0x00000084"
Fixes: f9eb91350bb2 ("i2c: aspeed: added slave support for Aspeed I2C driver")
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4a0057afa35872a5f2e65576785844688dd9fa5e ]
Idle bo's PTE needs to be re-created when resetting VM state machine.
Set idle bo's vm_bo as moved to mark it as invalid.
Fixes: 55bf196f60df ("drm/amdgpu: reset VM when an error is detected")
Signed-off-by: ZhenGuo Yin <zhenguo.yin@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 043465b66506e8c647cdd38a2db1f2ee0f369a1b ]
Add missing clk_disable_unprepare() and geni_se_resources_off() in the error
path in geni_i2c_probe().
Fixes: 14d02fbadb5d ("i2c: qcom-geni: add desc struct to prepare support for I2C Master Hub variant")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dbcab554f777390d9bb6a808ed0cd90ee59bb44e ]
Select the HDMI specific PLL clock only for HDMI outputs.
Fixes: 62618c7f117e ("drm/i915/mtl: C20 PLL programming")
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231213220526.1828827-1-imre.deak@intel.com
(cherry picked from commit 937d02cc79c6828fef28a4d80d8d0ad2f7bf2b62)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 768f17fd25e4a98bf5166148629ecf6f647d5efc ]
Updated i915 hwmon with fixes for issues reported by static analysis tool.
Fixed integer overflow with upcasting.
v2:
- Added Fixes tag (Badal).
- Updated commit message as per review comments (Anshuman).
Fixes: 4c2572fe0ae7 ("drm/i915/hwmon: Expose power1_max_interval")
Reviewed-by: Badal Nilawar <badal.nilawar@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Karthik Poosa <karthik.poosa@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231204144809.1518704-1-karthik.poosa@intel.com
(cherry picked from commit ac3420d3d428443a08b923f9118121c170192b62)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
mtk_wed_wo_queue_tx_clean()
[ Upstream commit 7cb8cd4daacfea646cf8b5925ca2c66c98b18480 ]
In order to avoid a NULL pointer dereference, check entry->buf pointer before running
skb_free_frag in mtk_wed_wo_queue_tx_clean routine.
Fixes: 799684448e3e ("net: ethernet: mtk_wed: introduce wed wo support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/3c1262464d215faa8acebfc08869798c81c96f4a.1702827359.git.lorenzo@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 340943fbff3d8faa44d2223ca04917df28786a07 ]
Mana uses PAGE_POOL API. x86_64 defconfig doesn't select it:
ld: vmlinux.o: in function `mana_create_page_pool.isra.0':
mana_en.c:(.text+0x9ae36f): undefined reference to `page_pool_create'
ld: vmlinux.o: in function `mana_get_rxfrag':
mana_en.c:(.text+0x9afed1): undefined reference to `page_pool_alloc_pages'
make[3]: *** [/home/yury/work/linux/scripts/Makefile.vmlinux:37: vmlinux] Error 1
make[2]: *** [/home/yury/work/linux/Makefile:1154: vmlinux] Error 2
make[1]: *** [/home/yury/work/linux/Makefile:234: __sub-make] Error 2
make[1]: Leaving directory '/home/yury/work/build-linux-x86_64'
make: *** [Makefile:234: __sub-make] Error 2
So we need to select it explicitly.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Fixes: ca9c54d2 ("net: mana: Add a driver for Microsoft Azure Network Adapter")
Link: https://lore.kernel.org/r/20231215203353.635379-1-yury.norov@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
