| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull IDE cleanup from David Miller:
"Just one minor cleanup"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
ide: use module_platform_driver()
|
|
Pull sparc updates from David Miller:
1) Add sparc RAM output to /proc/iomem, from Bob Picco.
2) Allow seeks on /dev/mdesc, from Khalid Aziz.
3) Cleanup sparc64 I/O accessors, from Sam Ravnborg.
4) If update_mmu_cache{,_pmd}() is called with an not-valid mapping, do
not insert it into the TLB miss hash tables otherwise we'll
livelock. Based upon work by Christopher Alexander Tobias Schulze.
5) Fix BREAK detection in sunsab driver when no actual characters are
pending, from Christopher Alexander Tobias Schulze.
6) Because we have modules --> openfirmware --> vmalloc ordering of
virtual memory, the lazy VMAP TLB flusher can cons up an invocation
of flush_tlb_kernel_range() that covers the openfirmware address
range. Unfortunately this will flush out the firmware's locked TLB
mapping which causes all kinds of trouble. Just split up the flush
request if this happens, but in the long term the lazy VMAP flusher
should probably be made a little bit smarter.
Based upon work by Christopher Alexander Tobias Schulze.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next:
sparc64: Fix up merge thinko.
sparc: Add "install" target
arch/sparc/math-emu/math_32.c: drop stray break operator
sparc64: ldc_connect() should not return EINVAL when handshake is in progress.
sparc64: Guard against flushing openfirmware mappings.
sunsab: Fix detection of BREAK on sunsab serial console
bbc-i2c: Fix BBC I2C envctrl on SunBlade 2000
sparc64: Do not insert non-valid PTEs into the TSB hash table.
sparc64: avoid code duplication in io_64.h
sparc64: reorder functions in io_64.h
sparc64: drop unused SLOW_DOWN_IO definitions
sparc64: remove macro indirection in io_64.h
sparc64: update IO access functions in PeeCeeI
sparcspkr: use sbus_*() primitives for IO
sparc: Add support for seek and shorter read to /dev/mdesc
sparc: use %s for unaligned panic
drivers/sbus/char: Micro-optimization in display7seg.c
display7seg: Introduce the use of the managed version of kzalloc
sparc64 - add mem to iomem resource
|
|
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull randomness updates from Ted Ts'o:
"Cleanups and bug fixes to /dev/random, add a new getrandom(2) system
call, which is a superset of OpenBSD's getentropy(2) call, for use
with userspace crypto libraries such as LibreSSL.
Also add the ability to have a kernel thread to pull entropy from
hardware rng devices into /dev/random"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
hwrng: Pass entropy to add_hwgenerator_randomness() in bits, not bytes
random: limit the contribution of the hw rng to at most half
random: introduce getrandom(2) system call
hw_random: fix sparse warning (NULL vs 0 for pointer)
random: use registers from interrupted code for CPU's w/o a cycle counter
hwrng: add per-device entropy derating
hwrng: create filler thread
random: add_hwgenerator_randomness() for feeding entropy from devices
random: use an improved fast_mix() function
random: clean up interrupt entropy accounting for archs w/o cycle counters
random: only update the last_pulled time if we actually transferred entropy
random: remove unneeded hash of a portion of the entropy pool
random: always update the entropy pool under the spinlock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security subsystem updates from James Morris:
"In this release:
- PKCS#7 parser for the key management subsystem from David Howells
- appoint Kees Cook as seccomp maintainer
- bugfixes and general maintenance across the subsystem"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (94 commits)
X.509: Need to export x509_request_asymmetric_key()
netlabel: shorter names for the NetLabel catmap funcs/structs
netlabel: fix the catmap walking functions
netlabel: fix the horribly broken catmap functions
netlabel: fix a problem when setting bits below the previously lowest bit
PKCS#7: X.509 certificate issuer and subject are mandatory fields in the ASN.1
tpm: simplify code by using %*phN specifier
tpm: Provide a generic means to override the chip returned timeouts
tpm: missing tpm_chip_put in tpm_get_random()
tpm: Properly clean sysfs entries in error path
tpm: Add missing tpm_do_selftest to ST33 I2C driver
PKCS#7: Use x509_request_asymmetric_key()
Revert "selinux: fix the default socket labeling in sock_graft()"
X.509: x509_request_asymmetric_keys() doesn't need string length arguments
PKCS#7: fix sparse non static symbol warning
KEYS: revert encrypted key change
ima: add support for measuring and appraising firmware
firmware_class: perform new LSM checks
security: introduce kernel_fw_from_file hook
PKCS#7: Missing inclusion of linux/err.h
...
|
|
Eliminate boilerplate code by using module_platform_driver().
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
arch/sparc/mm/init_64.c
Conflict was simple non-overlapping additions.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/Makefile
net/ipv6/sysctl_net_ipv6.c
Two ipv6_table_template[] additions overlap, so the index
of the ipv6_table[x] assignments needed to be adjusted.
In the drivers/net/Makefile case, we've gotten rid of the
garbage whereby we had to list every single USB networking
driver in the top-level Makefile, there is just one
"USB_NETWORKING" that guards everything.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer and time updates from Thomas Gleixner:
"A rather large update of timers, timekeeping & co
- Core timekeeping code is year-2038 safe now for 32bit machines.
Now we just need to fix all in kernel users and the gazillion of
user space interfaces which rely on timespec/timeval :)
- Better cache layout for the timekeeping internal data structures.
- Proper nanosecond based interfaces for in kernel users.
- Tree wide cleanup of code which wants nanoseconds but does hoops
and loops to convert back and forth from timespecs. Some of it
definitely belongs into the ugly code museum.
- Consolidation of the timekeeping interface zoo.
- A fast NMI safe accessor to clock monotonic for tracing. This is a
long standing request to support correlated user/kernel space
traces. With proper NTP frequency correction it's also suitable
for correlation of traces accross separate machines.
- Checkpoint/restart support for timerfd.
- A few NOHZ[_FULL] improvements in the [hr]timer code.
- Code move from kernel to kernel/time of all time* related code.
- New clocksource/event drivers from the ARM universe. I'm really
impressed that despite an architected timer in the newer chips SoC
manufacturers insist on inventing new and differently broken SoC
specific timers.
[ Ed. "Impressed"? I don't think that word means what you think it means ]
- Another round of code move from arch to drivers. Looks like most
of the legacy mess in ARM regarding timers is sorted out except for
a few obnoxious strongholds.
- The usual updates and fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
timekeeping: Fixup typo in update_vsyscall_old definition
clocksource: document some basic timekeeping concepts
timekeeping: Use cached ntp_tick_length when accumulating error
timekeeping: Rework frequency adjustments to work better w/ nohz
timekeeping: Minor fixup for timespec64->timespec assignment
ftrace: Provide trace clocks monotonic
timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
seqcount: Add raw_write_seqcount_latch()
seqcount: Provide raw_read_seqcount()
timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
timekeeping: Create struct tk_read_base and use it in struct timekeeper
timekeeping: Restructure the timekeeper some more
clocksource: Get rid of cycle_last
clocksource: Move cycle_last validation to core code
clocksource: Make delta calculation a function
wireless: ath9k: Get rid of timespec conversions
drm: vmwgfx: Use nsec based interfaces
drm: i915: Use nsec based interfaces
timekeeping: Provide ktime_get_raw()
hangcheck-timer: Use ktime_get_ns()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Nothing spectacular from the irq department this time:
- overhaul of the crossbar chip driver
- overhaul of the spear shirq chip driver
- support for the atmel-aic chip
- code move from arch to drivers
- the usual tiny fixlets
- two reverts worth to mention which undo the too simple attempt of
supporting wakeup interrupts on shared interrupt lines"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
Revert "irq: Warn when shared interrupts do not match on NO_SUSPEND"
Revert "PM / sleep / irq: Do not suspend wakeup interrupts"
irq: Warn when shared interrupts do not match on NO_SUSPEND
irqchip: atmel-aic: Define irq fixups for atmel SoCs
irqchip: atmel-aic: Implement RTC irq fixup
irqchip: atmel-aic: Add irq fixup infrastructure
irqchip: atmel-aic: Add atmel AIC/AIC5 drivers
irqchip: atmel-aic: Move binding doc to interrupt-controller directory
genirq: generic chip: Export irq_map_generic_chip function
PM / sleep / irq: Do not suspend wakeup interrupts
irqchip: or1k-pic: Migrate from arch/openrisc/
irqchip: crossbar: Allow for quirky hardware with direct hardwiring of GIC
documentation: dt: omap: crossbar: Add description for interrupt consumer
irqchip: crossbar: Introduce centralized check for crossbar write
irqchip: crossbar: Introduce ti, max-crossbar-sources to identify valid crossbar mapping
irqchip: crossbar: Add kerneldoc for crossbar_domain_unmap callback
irqchip: crossbar: Set cb pointer to null in case of error
irqchip: crossbar: Change the goto naming
irqchip: crossbar: Return proper error value
irqchip: crossbar: Fix kerneldoc warning
...
|
|
Enabling a Virtual Interface can result in an interrupt during the processing
of the VI Enable command and, in some paths, result in an attempt to issue
another command in the interrupt context, eventually crashing the system. Thus,
we disable interrupts during the course of the VI Enable command and ensure
enable doesn't sleep.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
USB network drivers are already handled in drivers/net/usb/Kconfig.
Let's save the maintenance burden of dependencies in drivers/net/Makefile.
The newly introduced USB_NET_DRIVERS umbrella config option defaults
to 'y' so as to minimize the changes of behavior.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tg3_tso_bug() was originally designed to handle only HW TX ring 0, Commit
d3f6f3a1d818410c17445bce4f4caab52eb102f1 ("tg3: Prevent page allocation failure
during TSO workaround") changed the driver logic to use tg3_tso_bug() for all
HW TX rings that are enabled. This patch fixes the regression by modifying
tg3_tso_bug() to handle multiple HW TX rings.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A change added to the mdiobus/phy api added a module_get/module_put
during phy connect/disconnect processing. Currently, the driver
performs a phy connect during module probe and a phy disconnect during
module remove. With the addition of the module_get during phy connect
the amd-xgbe module use count is incremented and can no longer be
unloaded.
Move the phy connect/disconnect from the driver probe/remove functions
to the net_device_ops ndo_open/ndo_stop functions. This allows the
module use count to be decremented when the device(s) are brought down
and allows the module to be unloaded.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the dma_set_mask_and_coherent function to set the DMA mask rather
than setting the DMA mask fields directly. This was originally done
to work around a bug in the arm64 DMA support when RAM started above
the 4GB boundary which has since been fixed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upon reception of a new frame, the emac driver checks for a number
of error conditions, and flag the packet as "bad" if any of these
are present. It then allocates a skb unconditionally, but only uses
it if the packet is "good". On the error path, the skb is just forgotten,
and the system leaks memory.
The piece of junk I have on my desk seems to encounter such error
frequently enough so that the box goes OOM after a couple of days,
which makes me grumpy.
Fix this by moving the allocation on the "good_packet" path (and
convert it to netdev_alloc_skb while we're at it).
Tested on a random Allwinner A20 board.
Cc: Stefan Roese <sr@denx.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.11+
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit a71e3c37960ce5f9 ("net: phy: Set the driver when registering an MDIO bus
device") caused the following regression on the fec driver:
root@imx6qsabresd:~# echo mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.003 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
Unable to handle kernel NULL pointer dereference at virtual address 0000002c
pgd = bcd14000
[0000002c] *pgd=4d9e0831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 617 Comm: sh Not tainted 3.16.0 #17
task: bc0c4e00 ti: bceb6000 task.ti: bceb6000
PC is at fec_suspend+0x10/0x70
LR is at dpm_run_callback.isra.7+0x34/0x6c
pc : [<803f8a98>] lr : [<80361f44>] psr: 600f0013
sp : bceb7d70 ip : bceb7d88 fp : bceb7d84
r10: 8091523c r9 : 00000000 r8 : bd88f478
r7 : 803f8a88 r6 : 81165988 r5 : 00000000 r4 : 00000000
r3 : 00000000 r2 : 00000000 r1 : bd88f478 r0 : bd88f478
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 4cd1404a DAC: 00000015
Process sh (pid: 617, stack limit = 0xbceb6240)
Stack: (0xbceb7d70 to 0xbceb8000)
....
The problem with the original commit is explained by Russell King:
"It has the effect (as can be seen from the oops) of attaching the MDIO bus
device (itself is a bus-less device) to the platform driver, which means
that if the platform driver supports power management, it will be called
to power manage the MDIO bus device.
Moreover, drivers do not expect to be called for power management
operations for devices which they haven't probed, and certainly not for
devices which aren't part of the same bus that the driver is registered
against."
This reverts commit a71e3c37960ce5f9c6a519bc1215e3ba9fa83e75.
Cc: <stable@vger.kernel.org> #3.16
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
routine
Need to turn off SGE RX/TX Callback Timers & interrupt in cxgb4vf PCI Shutdown
routine in order to prevent crashes during reboot/poweroff when traffic is
running.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable "err" is not necessary.
Return register_netdevice() directly.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- removal of sn9c102. This device driver was replaced a long time ago
by gspca
- solo6x10 and go7007 webcam drivers moved from staging into
mainstream. They were waiting for an API to allow setting the image
detection matrix
- SDR drivers moved from staging into mainstream: sdr-msi3101 (renamed
as msi2500) and rtl2832
- added SDR driver for airspy
- added demux driver: si2165
- rework at several RC subsystem, making the code for RC-5 SZ variant
to be added at the standard RC5 decoder
- added decoder for the XMP IR protocol
- tuner driver moved from staging into mainstream: msi3101 (renamed as
msi001)
- added documentation for some additional SDR pixfmt
- some device tree bindings documented
- added support for exynos3250 at s5p-jpeg
- remove the obsolete, unmaintained and broken mx1_camera driver
- added support for remote controllers at au0828 driver
- added a RC driver: sunxi-cir
- several driver fixes, enhancements and cleanups.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (455 commits)
[media] cx23885: fix UNSET/TUNER_ABSENT confusion
[media] coda: fix build error by making reset control optional
[media] radio-miropcm20: fix sparse NULL pointer warning
[media] MAINTAINERS: Update go7007 pattern
[media] MAINTAINERS: Update solo6x10 patterns
[media] media: atmel-isi: add primary DT support
[media] media: atmel-isi: convert the pdata from pointer to structure
[media] media: atmel-isi: add v4l2 async probe support
[media] rcar_vin: add devicetree support
[media] media: pxa_camera device-tree support
[media] media: mt9m111: add device-tree suppport
[media] soc_camera: add support for dt binding soc_camera drivers
[media] media: soc_camera: pxa_camera documentation device-tree support
[media] media: mt9m111: add device-tree documentation
[media] s5p-mfc: remove unnecessary calling to function video_devdata()
[media] s5p-jpeg: add chroma subsampling adjustment for Exynos3250
[media] s5p-jpeg: Prevent erroneous downscaling for Exynos3250 SoC
[media] s5p-jpeg: Assure proper crop rectangle initialization
[media] s5p-jpeg: fix g_selection op
[media] s5p-jpeg: Adjust jpeg_bound_align_image to Exynos3250 needs
...
|
|
These belong to the t4 msg header, will ensure there is no accidental code
duplication in the future
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Initialization of dcbnl_ops after register netdev may result in
dcbnl_ops not getting set before it is being accessed from open.
So, moving it before register_netdev.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Earlier, set_drv_version was getting called after register_netdev.
This was resulting in a race between set_drv_version and FLR called
from open(). Moving set_drv_version before register_netdev avoids
the race.
o Log response code in error message on CDRP failure.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Aggregating tx stats in adapter variable was resulting in
an increase in stats even after no traffic was run and
user runs ifconfig/ethtool command.
o qlcnic_update_stats used to accumulate stats in adapter
struct at each function call, instead accumulate tx stats
in local variable and then assign it to adapter structure.
Reported-by: Holger Kiehl <holger.kiehl@dwd.de>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A couple of nice new features this month, the ability to map
regulators in order to allow voltage control by external coprocessors
is something people have been asking for for a long time.
- improved support for switch only "regulators", allowing current
state to be read from the parent regulator but no setting.
- support for obtaining the register access method used to set
voltages, for use in systems which can offload control of this to a
coprocessor (typically for DVFS).
- support for Active-Semi AC8846, Dialog DA9211 and Texas Instruments
TPS65917"
* tag 'regulator-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (58 commits)
regulator: act8865: fix build when OF is not enabled
regulator: act8865: add act8846 to DT binding documentation
regulator: act8865: add support for act8846
regulator: act8865: prepare support for other act88xx devices
regulator: act8865: set correct number of regulators in pdata
regulator: act8865: Remove error variable in act8865_pmic_probe
regulator: act8865: fix parsing of platform data
regulator: tps65090: Set voltage for fixed regulators
regulator: core: Allow to get voltage count and list from parent
regulator: core: Get voltage from parent if not available
regulator: Add missing statics and inlines for stub functions
regulator: lp872x: Don't set constraints within the regulator driver
regmap: Fix return code for stub regmap_get_device()
regulator: s2mps11: Update module description and Kconfig to add S2MPU02 support
regulator: Add helpers for low-level register access
regmap: Allow regmap_get_device() to be used by modules
regmap: Add regmap_get_device
regulator: da9211: Remove unnecessary devm_regulator_unregister() calls
regulator: Add DT bindings for tps65218 PMIC regulators.
regulator: da9211: new regulator driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A quiet release, more bug fixes than anything else. A few things do
stand out though:
- updates to several drivers to move towards the standard GPIO chip
select handling in the core.
- DMA support for the SH MSIOF driver.
- support for Rockchip SPI controllers (their first mainline
submission)"
* tag 'spi-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (64 commits)
spi: davinci: use spi_device.cs_gpio to store gpio cs per spi device
spi: davinci: add support to configure gpio cs through dt
spi/pl022: Explicitly truncate large bitmask
spi/atmel: Fix pointer to int conversion warnings on 64 bit builds
spi: davinci: fix to support more than 2 chip selects
spi: topcliff-pch: don't hardcode PCI slot to get DMA device
spi: orion: fix incorrect handling of cell-index DT property
spi: orion: Fix error return code in orion_spi_probe()
spi/rockchip: fix error return code in rockchip_spi_probe()
spi/rockchip: remove redundant dev_err call in rockchip_spi_probe()
spi/rockchip: remove duplicated include from spi-rockchip.c
ARM: dts: fix the chip select gpios definition in the SPI nodes
spi: s3c64xx: Update binding documentation
spi: s3c64xx: use the generic SPI "cs-gpios" property
spi: s3c64xx: Revert "spi: s3c64xx: Added provision for dedicated cs pin"
spi: atmel: Use dmaengine_prep_slave_sg() API
spi: topcliff-pch: Update error messages for dmaengine_prep_slave_sg() API
spi: sh-msiof: Use correct device for DMA mapping with IOMMU
spi: sh-msiof: Handle dmaengine_prep_slave_single() failures gracefully
spi: rspi: Handle dmaengine_prep_slave_sg() failures gracefully
...
|
|
Currently when the guest is not able to receive more packets, qdisc layer starts
a timer, and when it goes off, qdisc is started again to deliver a packet again.
This is a very slow way to drain the queues, consumes unnecessary resources and
slows down other guests shutdown.
This patch change the behaviour by turning the carrier off when that timer
fires, so all the packets are freed up which were stucked waiting for that vif.
Instead of the rx_queue_purge bool it uses the VIF_STATUS_RX_PURGE_EVENT bit to
signal the thread that either the timeout happened or an RX interrupt arrived,
so the thread can check what it should do. It also disables NAPI, so the guest
can't transmit, but leaves the interrupts on, so it can resurrect.
Only the queues which brought down the interface can enable it again, the bit
QUEUE_STATUS_RX_STALLED makes sure of that.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces a new state bit VIF_STATUS_CONNECTED to track whether the
vif is in a connected state. Using carrier will not work with the next patch
in this series, which aims to turn the carrier temporarily off if the guest
doesn't seem to be able to receive packets.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
v2:
- rename the bitshift type to "enum state_bit_shift" here, not in the next patch
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
"This time with:
- support for the generic PCI device alias code in x86 IOMMU drivers
- a new sysfs interface for IOMMUs
- preparations for hotplug support in the Intel IOMMU driver
- change the AMD IOMMUv2 driver to not hold references to core data
structures like mm_struct or task_struct. Rely on mmu_notifers
instead.
- removal of the OMAP IOVMM interface, all users of it are converted
to DMA-API now
- make the struct iommu_ops const everywhere
- initial PCI support for the ARM SMMU driver
- there is now a generic device tree binding documented for ARM
IOMMUs
- various fixes and cleanups all over the place
Also included are some changes to the OMAP code, which are acked by
the maintainer"
* tag 'iommu-updates-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (67 commits)
devicetree: Add generic IOMMU device tree bindings
iommu/vt-d: Fix race setting IRQ CPU affinity while freeing IRQ
iommu/amd: Fix 2 typos in comments
iommu/amd: Fix device_state reference counting
iommu/amd: Remove change_pte mmu_notifier call-back
iommu/amd: Don't set pasid_state->mm to NULL in unbind_pasid
iommu/exynos: Select ARM_DMA_USE_IOMMU
iommu/vt-d: Exclude devices using RMRRs from IOMMU API domains
iommu/omap: Remove platform data da_start and da_end fields
ARM: omap: Don't set iommu pdata da_start and da_end fields
iommu/omap: Remove virtual memory manager
iommu/vt-d: Fix issue in computing domain's iommu_snooping flag
iommu/vt-d: Introduce helper function iova_size() to improve code readability
iommu/vt-d: Introduce helper domain_pfn_within_range() to simplify code
iommu/vt-d: Simplify intel_unmap_sg() and kill duplicated code
iommu/vt-d: Change iommu_enable/disable_translation to return void
iommu/vt-d: Simplify include/linux/dmar.h
iommu/vt-d: Avoid freeing virtual machine domain in free_dmar_iommu()
iommu/vt-d: Fix possible invalid memory access caused by free_dmar_iommu()
iommu/vt-d: Allocate dynamic domain id for virtual domains only
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"Notable changes:
- Heiko Schocher provided a driver for TI TMP103.
- Kamil Debski provided a driver for pwm-controlled fans.
- Neelesh Gupta provided a driver for power, fan rpm, voltage and
temperature reporting on powerpc/powernv systems.
- Scott Kanowitz provided a driver supporting Lattice's POWR1220
power manager IC.
- Richard Zhu provided a pmbus front-end driver for TPS40422.
- Frans Klaver added support for TMP112 to the lm75 driver.
- Johannes Pointner added support for EPCOS B57330V2103 to the
ntc_thermistor driver.
- Guenter Roeck added support for TMP441 and TMP442 to the tmp421
driver.
- Axel Lin converted several drivers to the new hwmon API (36 of
them, if I counted correctly), and cleaned up many of the drivers
along the way.
There are also a number of patches fixing bugs discovered while
testing Axel's changes"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (88 commits)
hwmon: (g762) Use of_property_read_u32 at appropriate place
hwmon: (sis5595) Prevent overflow problem when writing large limits
hwmon: (gpio-fan) Prevent overflow problem when writing large limits
hwmon: (ibmpowernv) Use of_property_read_u32 at appropriate place
hwmon: (lm85) Convert to devm_hwmon_device_register_with_groups
hwmon: (lm85) Avoid forward declaration
hwmon: (lm78) Convert to devm_hwmon_device_register_with_groups
hwmon: (max6697) Use of_property_read_bool at appropriate places
hwmon: (pwm-fan) Make SENSORS_PWM_FAN depend on OF
hwmon: (pwm-fan) Remove duplicate dev_set_drvdata call
hwmon: (nct6775) Remove num_attr_groups from struct nct6775_data
hwmon: (nct6775) Update module description and Kconfig for NCT6106D and NCT6791D
hwmon: (adt7411) Convert to devm_hwmon_device_register_with_groups
hwmon: (g762) Convert to hwmon_device_register_with_groups
hwmon: (emc2103) Convert to devm_hwmon_device_register_with_groups
hwmon: (smsc47m1) Avoid forward declaration
hwmon: (smsc47m192) Convert to devm_hwmon_device_register_with_groups
hwmon: (smsc47m192) Avoid forward declaration
hwmon: (max1668) Make max1668_addr_list array const
hwmon: (max6639) Make normal_i2c array const
...
|
|
rng_get_data() returns the number of bytes read from the hardware.
The entropy argument to add_hwgenerator_randomness() is passed
directly to credit_entropy_bits() so we should be passing the
number of bits, not bytes here.
Fixes: be4000bc464 "hwrng: create filler thread"
Acked-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
For people who don't trust a hardware RNG which can not be audited,
the changes to add support for RDSEED can be troubling since 97% or
more of the entropy will be contributed from the in-CPU hardware RNG.
We now have a in-kernel khwrngd, so for those people who do want to
implicitly trust the CPU-based system, we could create an arch-rng
hw_random driver, and allow khwrng refill the entropy pool. This
allows system administrator whether or not they trust the CPU (I
assume the NSA will trust RDRAND/RDSEED implicitly :-), and if so,
what level of entropy derating they want to use.
The reason why this is a really good idea is that if different people
use different levels of entropy derating, it will make it much more
difficult to design a backdoor'ed hwrng that can be generally
exploited in terms of the output of /dev/random when different attack
targets are using differing levels of entropy derating.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
The getrandom(2) system call was requested by the LibreSSL Portable
developers. It is analoguous to the getentropy(2) system call in
OpenBSD.
The rationale of this system call is to provide resiliance against
file descriptor exhaustion attacks, where the attacker consumes all
available file descriptors, forcing the use of the fallback code where
/dev/[u]random is not available. Since the fallback code is often not
well-tested, it is better to eliminate this potential failure mode
entirely.
The other feature provided by this new system call is the ability to
request randomness from the /dev/urandom entropy pool, but to block
until at least 128 bits of entropy has been accumulated in the
/dev/urandom entropy pool. Historically, the emphasis in the
/dev/urandom development has been to ensure that urandom pool is
initialized as quickly as possible after system boot, and preferably
before the init scripts start execution.
This is because changing /dev/urandom reads to block represents an
interface change that could potentially break userspace which is not
acceptable. In practice, on most x86 desktop and server systems, in
general the entropy pool can be initialized before it is needed (and
in modern kernels, we will printk a warning message if not). However,
on an embedded system, this may not be the case. And so with this new
interface, we can provide the functionality of blocking until the
urandom pool has been initialized. Any userspace program which uses
this new functionality must take care to assure that if it is used
during the boot process, that it will not cause the init scripts or
other portions of the system startup to hang indefinitely.
SYNOPSIS
#include <linux/random.h>
int getrandom(void *buf, size_t buflen, unsigned int flags);
DESCRIPTION
The system call getrandom() fills the buffer pointed to by buf
with up to buflen random bytes which can be used to seed user
space random number generators (i.e., DRBG's) or for other
cryptographic uses. It should not be used for Monte Carlo
simulations or other programs/algorithms which are doing
probabilistic sampling.
If the GRND_RANDOM flags bit is set, then draw from the
/dev/random pool instead of the /dev/urandom pool. The
/dev/random pool is limited based on the entropy that can be
obtained from environmental noise, so if there is insufficient
entropy, the requested number of bytes may not be returned.
If there is no entropy available at all, getrandom(2) will
either block, or return an error with errno set to EAGAIN if
the GRND_NONBLOCK bit is set in flags.
If the GRND_RANDOM bit is not set, then the /dev/urandom pool
will be used. Unlike using read(2) to fetch data from
/dev/urandom, if the urandom pool has not been sufficiently
initialized, getrandom(2) will block (or return -1 with the
errno set to EAGAIN if the GRND_NONBLOCK bit is set in flags).
The getentropy(2) system call in OpenBSD can be emulated using
the following function:
int getentropy(void *buf, size_t buflen)
{
int ret;
if (buflen > 256)
goto failure;
ret = getrandom(buf, buflen, 0);
if (ret < 0)
return ret;
if (ret == buflen)
return 0;
failure:
errno = EIO;
return -1;
}
RETURN VALUE
On success, the number of bytes that was filled in the buf is
returned. This may not be all the bytes requested by the
caller via buflen if insufficient entropy was present in the
/dev/random pool, or if the system call was interrupted by a
signal.
On error, -1 is returned, and errno is set appropriately.
ERRORS
EINVAL An invalid flag was passed to getrandom(2)
EFAULT buf is outside the accessible address space.
EAGAIN The requested entropy was not available, and
getentropy(2) would have blocked if the
GRND_NONBLOCK flag was not set.
EINTR While blocked waiting for entropy, the call was
interrupted by a signal handler; see the description
of how interrupted read(2) calls on "slow" devices
are handled with and without the SA_RESTART flag
in the signal(7) man page.
NOTES
For small requests (buflen <= 256) getrandom(2) will not
return EINTR when reading from the urandom pool once the
entropy pool has been initialized, and it will return all of
the bytes that have been requested. This is the recommended
way to use getrandom(2), and is designed for compatibility
with OpenBSD's getentropy() system call.
However, if you are using GRND_RANDOM, then getrandom(2) may
block until the entropy accounting determines that sufficient
environmental noise has been gathered such that getrandom(2)
will be operating as a NRBG instead of a DRBG for those people
who are working in the NIST SP 800-90 regime. Since it may
block for a long time, these guarantees do *not* apply. The
user may want to interrupt a hanging process using a signal,
so blocking until all of the requested bytes are returned
would be unfriendly.
For this reason, the user of getrandom(2) MUST always check
the return value, in case it returns some error, or if fewer
bytes than requested was returned. In the case of
!GRND_RANDOM and small request, the latter should never
happen, but the careful userspace code (and all crypto code
should be careful) should check for this anyway!
Finally, unless you are doing long-term key generation (and
perhaps not even then), you probably shouldn't be using
GRND_RANDOM. The cryptographic algorithms used for
/dev/urandom are quite conservative, and so should be
sufficient for all purposes. The disadvantage of GRND_RANDOM
is that it can block, and the increased complexity required to
deal with partially fulfilled getrandom(2) requests.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Zach Brown <zab@zabbo.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
Conflicts:
net/6lowpan/iphc.c
Minor conflicts in iphc.c were changes overlapping with some
style cleanups.
John W. Linville says:
====================
Please pull this last(?) batch of wireless change intended for the
3.17 stream...
For the NFC bits, Samuel says:
"This is a rather quiet one, we have:
- A new driver from ST Microelectronics for their NCI ST21NFCB,
including device tree support.
- p2p support for the ST21NFCA driver
- A few fixes an enhancements for the NFC digital laye"
For the Atheros bits, Kalle says:
"Michal and Janusz did some important RX aggregation fixes, basically we
were missing RX reordering altogether. The 10.1 firmware doesn't support
Ad-Hoc mode and Michal fixed ath10k so that it doesn't advertise Ad-Hoc
support with that firmware. Also he implemented a workaround for a KVM
issue."
For the Bluetooth bits, Gustavo and Johan say:
"To quote Gustavo from his previous request:
'Some last minute fixes for -next. We have a fix for a use after free in
RFCOMM, another fix to an issue with ADV_DIRECT_IND and one for ADV_IND with
auto-connection handling. Last, we added support for reading the codec and
MWS setting for controllers that support these features.'
Additionally there are fixes to LE scanning, an update to conform to the 4.1
core specification as well as fixes for tracking the page scan state. All
of these fixes are important for 3.17."
And,
"We've got:
- 6lowpan fixes/cleanups
- A couple crash fixes, one for the Marvell HCI driver and another in LE SMP.
- Fix for an incorrect connected state check
- Fix for the bondable requirement during pairing (an issue which had
crept in because of using "pairable" when in fact the actual meaning
was "bondable" (these have different meanings in Bluetooth)"
Along with those are some late-breaking hardware support patches in
brcmfmac and b43 as well as a stray ath9k patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After this patch:
[ 32.985530] hso: drivers/net/usb/hso.c: Option Wireless
[ 33.000452] hso 2-1.4:1.7: Not our interface
[ 33.001849] usbcore: registered new interface driver hso
root@qt5022:~# ls /dev/ttyHS*
/dev/ttyHS0 /dev/ttyHS1 /dev/ttyHS2 /dev/ttyHS3 /dev/ttyHS4
/dev/ttyHS5
root@qt5022:~# lsusb -d 0af0: -vvv
Bus 002 Device 003: ID 0af0:9200 Option
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 255 Vendor Specific Protocol
bMaxPacketSize0 64
idVendor 0x0af0 Option
idProduct 0x9200
bcdDevice 0.00
iManufacturer 3 Option N.V.
iProduct 2 Globetrotter HSUPA Modem
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 200
bNumInterfaces 8
bConfigurationValue 1
iConfiguration 1 Option Configuration
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 4
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 5
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x06 EP 6 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 6
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x87 EP 7 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x88 EP 8 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x07 EP 7 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 32
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 7
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x08 EP 8 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x89 EP 9 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 255 Vendor Specific Protocol
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into regulator-next
|
|
'regulator/topic/tps65218', 'regulator/topic/tps6586x' and 'regulator/topic/twl' into regulator-next
|
|
'regulator/topic/s2mpu02', 'regulator/topic/s5m8767' and 'regulator/topic/tps65090' into regulator-next
|
|
'regulator/topic/ltc3589', 'regulator/topic/max8952', 'regulator/topic/mc13xxx' and 'regulator/topic/palmas' into regulator-next
|
|
'regulator/topic/getreg', 'regulator/topic/gpio' and 'regulator/topic/lp872x' into regulator-next
|
|
'regulator/topic/ab8500', 'regulator/topic/act8865', 'regulator/topic/as3722' and 'regulator/topic/bcm590xx' into regulator-next
|
|
|
|
'regulator/fix/arizona' and 'regulator/fix/tps65218' into regulator-linus
|
|
Pull ARM updates from Russell King:
"Included in this update:
- perf updates from Will Deacon:
The main changes are callchain stability fixes from Jean Pihet and
event mapping and PMU name rework from Mark Rutland
The latter is preparatory work for enabling some code re-use with
arm64 in the future.
- updates for nommu from Uwe Kleine-König:
Two different fixes for the same problem making some ARM nommu
configurations not boot since 3.6-rc1. The problem is that
user_addr_max returned the biggest available RAM address which
makes some copy_from_user variants fail to read from XIP memory.
- deprecate legacy OMAP DMA API, in preparation for it's removal.
The popular drivers have been converted over, leaving a very small
number of rarely used drivers, which hopefully can be converted
during the next cycle with a bit more visibility (and hopefully
people popping out of the woodwork to help test)
- more tweaks for BE systems, particularly with the kernel image
format. In connection with this, I've cleaned up the way we
generate the linker script for the decompressor.
- removal of hard-coded assumptions of the kernel stack size, making
everywhere depend on the value of THREAD_SIZE_ORDER.
- MCPM updates from Nicolas Pitre.
- Make it easier for proper CPU part number checks (which should
always include the vendor field).
- Assembly code optimisation - use the "bx" instruction when
returning from a function on ARMv6+ rather than "mov pc, reg".
- Save the last kernel misaligned fault location and report it via
the procfs alignment file.
- Clean up the way we create the initial stack frame, which is a
repeated pattern in several different locations.
- Support for 8-byte get_user(), needed for some DRM implementations.
- mcs locking from Will Deacon.
- Save and restore a few more Cortex-A9 registers (for errata
workarounds)
- Fix various aspects of the SWP emulation, and the ELF hwcap for the
SWP instruction.
- Update LPAE logic for pte_write and pmd_write to make it more
correct.
- Support for Broadcom Brahma15 CPU cores.
- ARM assembly crypto updates from Ard Biesheuvel"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (53 commits)
ARM: add comments to the early page table remap code
ARM: 8122/1: smp_scu: enable SCU standby support
ARM: 8121/1: smp_scu: use macro for SCU enable bit
ARM: 8120/1: crypto: sha512: add ARM NEON implementation
ARM: 8119/1: crypto: sha1: add ARM NEON implementation
ARM: 8118/1: crypto: sha1/make use of common SHA-1 structures
ARM: 8113/1: remove remaining definitions of PLAT_PHYS_OFFSET from <mach/memory.h>
ARM: 8111/1: Enable erratum 798181 for Broadcom Brahma-B15
ARM: 8110/1: do CPU-specific init for Broadcom Brahma15 cores
ARM: 8109/1: mm: Modify pte_write and pmd_write logic for LPAE
ARM: 8108/1: mm: Introduce {pte,pmd}_isset and {pte,pmd}_isclear
ARM: hwcap: disable HWCAP_SWP if the CPU advertises it has exclusives
ARM: SWP emulation: only initialise on ARMv7 CPUs
ARM: SWP emulation: always enable when SMP is enabled
ARM: 8103/1: save/restore Cortex-A9 CP15 registers on suspend/resume
ARM: 8098/1: mcs lock: implement wfe-based polling for MCS locking
ARM: 8091/2: add get_user() support for 8 byte types
ARM: 8097/1: unistd.h: relocate comments back to place
ARM: 8096/1: Describe required sort order for textofs-y (TEXT_OFFSET)
ARM: 8090/1: add revision info for PL310 errata 588369 and 727915
...
|
|
act8846_matches and act8865_matches are defined only when OF is
enabled. Move references to them to the act8865_pdata_from_dt()
function to avoid a build error when OF is disabled.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add device id and definition of registers and regulators to support
the act8846 PMU.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch prepares support for other devices in the act88xx family of
PMUs manufactured by Active-Semi.
http://www.active-semi.com/products/power-management-units/act88xx/
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
act8865_pdata_from_dt() populates the array pdata->regulators with all
the regulators and then assigns the field init_data only for the ones
actually found in the DT.
The patch changes the value assigned to pdata->num_regulators to match
the size of the array.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
