| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Sort usb device id table for enhanced readability.
Signed-off-by: Jiande Lu <jiande.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add HW IDs for wireless module specific to Acer/ASUS
notebook models to ensure proper recognition and functionality.
These HW IDs are extracted from Windows driver inf file.
Note some HW IDs without official drivers, still in testing phase.
Thus, we update module HW ID and test ensure consistent boot success.
Signed-off-by: Jiande Lu <jiande.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Download board id specific NVM instead of default for WCN7850 if board id
is available.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The hardware information surfaced via debugfs might be usable by the
userspace to set some configuration knobs. This patch sets the hw_info
for Intel and Realtek chipsets.
Below are some possible output of the hardware_info debugfs file.
INTEL platform=55 variant=24
RTL lmp_subver=34898 hci_rev=10 hci_ver=11 hci_bus=1
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
USB driver defines macro @USB_CTRL_SET_TIMEOUT for sending control message
timeout and @USB_CTRL_GET_TIMEOUT for receiving, but usb_control_msg()
uses wrong macro @USB_CTRL_SET_TIMEOUT as argument to receive control
message, fixed by using @USB_CTRL_GET_TIMEOUT to receive message.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Because both MT7920 and MT7921 use the same chip ID.
We use the 8th bit of fw_flavor to distingush MT7920.
The original patch made a mistake to check whole fw_flavor,
that makes the condition both true (dev_id == 0x7961 && fw_flavor),
and makes MT7921 flow wrong.
In this patch, we correct the flow to get the 8th bit value for MT7920.
And the patch is verified pass with both MT7920 and MT7921.
Signed-off-by: Peter Tsao <peter.tsao@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This fixes some CHECKs reported by the checkpatch script.
Issues reported in ath3k.c:
-------
ath3k.c
-------
CHECK: Please don't use multiple blank lines
+
+
CHECK: Blank lines aren't necessary after an open brace '{'
+static const struct usb_device_id ath3k_blist_tbl[] = {
+
CHECK: Alignment should match open parenthesis
+static int ath3k_load_firmware(struct usb_device *udev,
+ const struct firmware *firmware)
CHECK: Alignment should match open parenthesis
+ err = usb_bulk_msg(udev, pipe, send_buf, size,
+ &len, 3000);
CHECK: Unnecessary parentheses around 'len != size'
+ if (err || (len != size)) {
CHECK: Alignment should match open parenthesis
+static int ath3k_get_version(struct usb_device *udev,
+ struct ath3k_version *version)
CHECK: Alignment should match open parenthesis
+static int ath3k_load_fwfile(struct usb_device *udev,
+ const struct firmware *firmware)
CHECK: Alignment should match open parenthesis
+ err = usb_bulk_msg(udev, pipe, send_buf, size,
+ &len, 3000);
CHECK: Unnecessary parentheses around 'len != size'
+ if (err || (len != size)) {
CHECK: Blank lines aren't necessary after an open brace '{'
+ switch (fw_version.ref_clock) {
+
CHECK: Alignment should match open parenthesis
+ snprintf(filename, ATH3K_NAME_LEN, "ar3k/ramps_0x%08x_%d%s",
+ le32_to_cpu(fw_version.rom_version), clk_value, ".dfu");
CHECK: Alignment should match open parenthesis
+static int ath3k_probe(struct usb_interface *intf,
+ const struct usb_device_id *id)
CHECK: Alignment should match open parenthesis
+ BT_ERR("Firmware file \"%s\" not found",
+ ATH3K_FIRMWARE);
CHECK: Alignment should match open parenthesis
+ BT_ERR("Firmware file \"%s\" request failed (err=%d)",
+ ATH3K_FIRMWARE, ret);
total: 0 errors, 0 warnings, 14 checks, 540 lines checked
Signed-off-by: Uri Arev <me@wantyapps.xyz>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Like the bcm43430a0 the bcm43455 BT does not support the 0xfc45 command
to set the UART clock to 48 MHz and because of this it does not work
at 4000000 baud.
These chips are found on ACPI/x86 devices where the operating baudrate
does not come from the firmware but is hardcoded at 4000000, which does
not work.
Make the driver_data for the "BCM2EA4" ACPI HID which is used for
the bcm43455 BT point to bcm43430_device_data which limits the baudrate
to 2000000.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This fixes the following CHECKs, WARNINGs, and ERRORs reported in
hci_intel.c
Reported by checkpatch.pl:
-----------
hci_intel.c
-----------
WARNING: Prefer using '"%s...", __func__' to using 'intel_setup', this
function's name, in a string
+ bt_dev_dbg(hdev, "start intel_setup");
ERROR: code indent should use tabs where possible
+ /* Check for supported iBT hardware variants of this firmware$
ERROR: code indent should use tabs where possible
+ * loading method.$
ERROR: code indent should use tabs where possible
+ *$
ERROR: code indent should use tabs where possible
+ * This check has been put in place to ensure correct forward$
ERROR: code indent should use tabs where possible
+ * compatibility options when newer hardware variants come along.$
ERROR: code indent should use tabs where possible
+ */$
CHECK: No space is necessary after a cast
+ duration = (unsigned long long) ktime_to_ns(delta) >> 10;
CHECK: No space is necessary after a cast
+ duration = (unsigned long long) ktime_to_ns(delta) >> 10;
WARNING: Missing a blank line after declarations
+ int err = PTR_ERR(intel->rx_skb);
+ bt_dev_err(hu->hdev, "Frame reassembly failed (%d)", err);
Signed-off-by: Uri Arev <me@wantyapps.xyz>
Suggested-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This patch adds support for the MediaTek MT7922 Bluetooth device.
The information in /sys/kernel/debug/usb/devices about the MT7922
is as follows:
T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3585 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Ian W MORRISON <ianwmorrison@live.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Some variants of Intel controllers like BlazarI supports downloading of
Intermediate bootloader (IML) image. IML gives flexibility to fix issues as its
not possible to fix issue in Primary bootloader once flashed to ROM. This patch
adds the support to download IML before downloading operational firmware image.
dmesg logs:
[13.399003] Bluetooth: Core ver 2.22
[13.399006] Bluetooth: Starting self testing
[13.401194] Bluetooth: ECDH test passed in 2135 usecs
[13.421175] Bluetooth: SMP test passed in 597 usecs
[13.421184] Bluetooth: Finished self testing
[13.422919] Bluetooth: HCI device and connection manager initialized
[13.422923] Bluetooth: HCI socket layer initialized
[13.422925] Bluetooth: L2CAP socket layer initialized
[13.422930] Bluetooth: SCO socket layer initialized
[13.458065] Bluetooth: hci0: Device revision is 0
[13.458071] Bluetooth: hci0: Secure boot is disabled
[13.458072] Bluetooth: hci0: OTP lock is disabled
[13.458072] Bluetooth: hci0: API lock is enabled
[13.458073] Bluetooth: hci0: Debug lock is disabled
[13.458073] Bluetooth: hci0: Minimum firmware build 1 week 10 2014
[13.458075] Bluetooth: hci0: Bootloader timestamp 2022.46 buildtype 1 build 26590
[13.458324] Bluetooth: hci0: DSM reset method type: 0x00
[13.460678] Bluetooth: hci0: Found device firmware: intel/ibt-0090-0291-iml.sfi
[13.460684] Bluetooth: hci0: Boot Address: 0x30099000
[13.460685] Bluetooth: hci0: Firmware Version: 227-11.24
[13.562554] Bluetooth: hci0: Waiting for firmware download to complete
[13.563023] Bluetooth: hci0: Firmware loaded in 99941 usecs
[13.563057] Bluetooth: hci0: Waiting for device to boot
[13.565029] Bluetooth: hci0: Malformed MSFT vendor event: 0x02
[13.565148] Bluetooth: hci0: Device booted in 2064 usecs
[13.567065] Bluetooth: hci0: No device address configured
[13.569010] Bluetooth: hci0: Found device firmware: intel/ibt-0090-0291.sfi
[13.569061] Bluetooth: hci0: Boot Address: 0x10000800
[13.569062] Bluetooth: hci0: Firmware Version: 227-11.24
[13.788891] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[13.788897] Bluetooth: BNEP filters: protocol multicast
[13.788902] Bluetooth: BNEP socket layer initialized
[15.435905] Bluetooth: hci0: Waiting for firmware download to complete
[15.436016] Bluetooth: hci0: Firmware loaded in 1823233 usecs
[15.436258] Bluetooth: hci0: Waiting for device to boot
[15.471140] Bluetooth: hci0: Device booted in 34277 usecs
[15.471201] Bluetooth: hci0: Malformed MSFT vendor event: 0x02
[15.471487] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-0090-0291.ddc
[15.474353] Bluetooth: hci0: Applying Intel DDC parameters completed
[15.474486] Bluetooth: hci0: Found Intel DDC parameters: intel/bdaddress.cfg
[15.475299] Bluetooth: hci0: Applying Intel DDC parameters completed
[15.479381] Bluetooth: hci0: Firmware timestamp 2024.10 buildtype 3 build 58595
[15.479385] Bluetooth: hci0: Firmware SHA1: 0xb4f3cc46
[15.483243] Bluetooth: hci0: Fseq status: Success (0x00)
[15.483246] Bluetooth: hci0: Fseq executed: 00.00.00.00
[15.483247] Bluetooth: hci0: Fseq BT Top: 00.00.00.00
[15.578712] Bluetooth: MGMT ver 1.22
[15.822682] Bluetooth: RFCOMM TTY layer initialized
[15.822690] Bluetooth: RFCOMM socket layer initialized
[15.822695] Bluetooth: RFCOMM ver 1.11
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Use macro for image type instead of using hard code number.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The blamed commit started to use the ptp workqueue to get the second
part of the timestamp. And when the port was set down, then this
workqueue is stopped. But if the config option NETWORK_PHY_TIMESTAMPING
is not enabled, then the ptp_clock is not initialized so then it would
crash when it would try to access the delayed work.
So then basically by setting up and then down the port, it would crash.
The fix consists in checking if the ptp_clock is initialized and only
then cancel the delayed work.
Fixes: cc7554954848 ("net: micrel: Change to receive timestamp in the frame for lan8841")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- implement full support for WinWing Orion2 (Ivan Gorinov)
|
|
|
|
- support for Deck IMU in hid-steam (Max Maisel)
|
|
|
|
- fixes for better support of 3rd party playstation DS4 controllers (Max Staudt)
|
|
- conversion of HID device drivers from platform_driver->remove() to
platform_driver->remove_new() (Uwe Kleine-König)
|
|
|
|
|
|
- Implement loading firmware from host in intel-ish driver, needed
to support Lunar Lake and later (Zhang Lixu)
|
|
- PM fixes for STM and Weida Tech devices (Kenny Levinsen)
|
|
- conversion from sprintf() to sysfs_emit() (Li Zhijian)
|
|
- support for missing mappings and codes from HUT 1.5 in
hid-debug (Thomas Kuehne)
|
|
- updates to HID-BPF infrastructure, with some of the specific
fixes (e.g. rdesc fixups) abstracted into separate BPF programs
for consumption by libevdev/udev-hid-bpf (Benjamin Tissoires)
|
|
- initial support for ROG Ally and ROG X13 devices (Luke D. Jones)
- other small assorted cleanups of hid-asus driver (Luke D. Jones)
|
|
- PM fix and assorted other code cleanups for amd-sfh (Basavaraj Natikar)
|
|
The bcm2835-unicam driver calls the clk_set_min_rate() function, which
is declared but not implemented on platforms that don't provide
COMMON_CLK. This causes linkage failures with some configurations.
Fix it by depending on COMMON_CLK. This only slightly restricts
compilation testing, but not usage of the driver as all platforms on
which the hardware can be found provide COMMON_CLK.
Fixes: 392cd78d495f ("media: bcm2835-unicam: Add support for CCP2/CSI2 camera interface")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202405112243.2MLRT7li-lkp@intel.com/
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Pull DSA and IAA accelerator mis-alignment fix from Arjan van de Ven:
"The DSA (memory copy/zero/etc) and IAA (compression) accelerators in
the Sapphire Rapids and Emerald Rapids SOCs turn out to have a bug
that has security implications.
Both of these accelerators work by the application submitting a 64
byte command to the device; this command contains an opcode as well as
the virtual address of the return value that the device will update on
completion... and a set of opcode specific values.
In a typical scenario a ring 3 application mmaps the device file and
uses the ENQCMD or MOVDIR64 instructions (which are variations of a 64
byte atomic write) on this mmap'd memory region to directly submit
commands to a device hardware.
The return value as specified in the command, is supposed to be 32 (or
64) bytes aligned in memory, and generally the hardware checks and
enforces this alignment.
However in testing it has been found that there are conditions
(controlled by the submitter) where this enforcement does not
happen... which makes it possible for the return value to span a page
boundary. And this is where it goes wrong - the accelerators will
perform the virtual to physical address lookup on the first of the two
pages, but end up continue writing to the next consecutive physical
(host) page rather than the consecutive virtual page. In addition, the
device will end up in a hung state on such unaligned write of the
return value.
This patch series has the proposed software side solution consisting
of three parts:
- Don't allow these two PCI devices to be assigned to VM guests (we
cannot trust a VM guest to behave correctly and not cause this
condition)
- Don't allow ring 3 applications to set up the mmap unless they have
CAP_SYS_RAWIO permissions. This makes it no longer possible for
non-root applications to directly submit commands to the
accelerator
- Add a write() method to the device so that an application can
submit its commands to the kernel driver, which performs the needed
sanity checks before submitting it to the hardware.
This switch from mmap to write is an incompatible interface change to
non-root userspace, but we have not found a way to avoid this. All
software we know of uses a small set of accessor libraries for these
accelerators, for which libqpl and libdml (on github) are the most
common. As part of the security release, updated versions of these
libraries will be released that transparently fall back to write().
Intel has assigned CVE-2024-21823 to this hardware issue"
* tag 'idxd-for-linus-may2024' of git bundle from Arjan:
dmaengine: idxd: add a write() method for applications to submit work
dmaengine: idxd: add a new security check to deal with a hardware erratum
VFIO: Add the SPR_DSA and SPR_IAX devices to the denylist
|
|
The series is causing issues with PHY drivers built as modules.
Since it was only partially applied and the merge window has
opened let's revert and try again for v6.11.
Revert 6916e461e793 ("net: phy: Introduce ethernet link topology representation")
Revert 0ec5ed6c130e ("net: sfp: pass the phy_device when disconnecting an sfp module's PHY")
Revert e75e4e074c44 ("net: phy: add helpers to handle sfp phy connect/disconnect")
Revert fdd353965b52 ("net: sfp: Add helper to return the SFP bus name")
Revert 841942bc6212 ("net: ethtool: Allow passing a phy index for some commands")
Link: https://lore.kernel.org/all/171242462917.4000.9759453824684907063.git-patchwork-notify@kernel.org/
Link: https://lore.kernel.org/all/20240507102822.2023826-1-maxime.chevallier@bootlin.com/
Link: https://lore.kernel.org/r/20240513154156.104281-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the EST structure to struct stmmac_priv, because the
EST configs don't look like platform config, but EST is
enabled in runtime with the settings retrieved for the TC
TAPRIO feature also in runtime. So it's better to have the
EST-data preserved in the driver private data instead of
the platform data storage.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240513014346.1718740-3-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reinitialize the whole EST structure would also reset the mutex
lock which is embedded in the EST structure, and then trigger
the following warning. To address this, move the lock to struct
stmmac_priv. We also need to reacquire the mutex lock when doing
this initialization.
DEBUG_LOCKS_WARN_ON(lock->magic != lock)
WARNING: CPU: 3 PID: 505 at kernel/locking/mutex.c:587 __mutex_lock+0xd84/0x1068
Modules linked in:
CPU: 3 PID: 505 Comm: tc Not tainted 6.9.0-rc6-00053-g0106679839f7-dirty #29
Hardware name: NXP i.MX8MPlus EVK board (DT)
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __mutex_lock+0xd84/0x1068
lr : __mutex_lock+0xd84/0x1068
sp : ffffffc0864e3570
x29: ffffffc0864e3570 x28: ffffffc0817bdc78 x27: 0000000000000003
x26: ffffff80c54f1808 x25: ffffff80c9164080 x24: ffffffc080d723ac
x23: 0000000000000000 x22: 0000000000000002 x21: 0000000000000000
x20: 0000000000000000 x19: ffffffc083bc3000 x18: ffffffffffffffff
x17: ffffffc08117b080 x16: 0000000000000002 x15: ffffff80d2d40000
x14: 00000000000002da x13: ffffff80d2d404b8 x12: ffffffc082b5a5c8
x11: ffffffc082bca680 x10: ffffffc082bb2640 x9 : ffffffc082bb2698
x8 : 0000000000017fe8 x7 : c0000000ffffefff x6 : 0000000000000001
x5 : ffffff8178fe0d48 x4 : 0000000000000000 x3 : 0000000000000027
x2 : ffffff8178fe0d50 x1 : 0000000000000000 x0 : 0000000000000000
Call trace:
__mutex_lock+0xd84/0x1068
mutex_lock_nested+0x28/0x34
tc_setup_taprio+0x118/0x68c
stmmac_setup_tc+0x50/0xf0
taprio_change+0x868/0xc9c
Fixes: b2aae654a479 ("net: stmmac: add mutex lock to protect est parameters")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240513014346.1718740-2-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change the Kconfig dependency, so this driver can be built and run on ARM64
with 4K page size.
16/64K page sizes are not supported yet.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1715632141-8089-1-git-send-email-haiyangz@microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The "struct prestera_msg_vtcam_rule_add_req" uses a dynamically sized
set of trailing elements. Specifically, it uses an array of structures
of type "prestera_msg_acl_action actions_msg".
The "struct prestera_msg_flood_domain_ports_set_req" also uses a
dynamically sized set of trailing elements. Specifically, it uses an
array of structures of type "prestera_msg_acl_action actions_msg".
So, use the preferred way in the kernel declaring flexible arrays [1].
At the same time, prepare for the coming implementation by GCC and Clang
of the __counted_by attribute. Flexible array members annotated with
__counted_by can have their accesses bounds-checked at run-time via
CONFIG_UBSAN_BOUNDS (for array indexing) and CONFIG_FORTIFY_SOURCE (for
strcpy/memcpy-family functions). In this case, it is important to note
that the attribute used is specifically __counted_by_le since the
counters are of type __le32.
The logic does not need to change since the counters for the flexible
arrays are asigned before any access to the arrays.
The order in which the structure prestera_msg_vtcam_rule_add_req and the
structure prestera_msg_flood_domain_ports_set_req are defined must be
changed to avoid incomplete type errors.
Also, avoid the open-coded arithmetic in memory allocator functions [2]
using the "struct_size" macro.
Moreover, the new structure members also allow us to avoid the open-
coded arithmetic on pointers. So, take advantage of this refactoring
accordingly.
This code was detected with the help of Coccinelle, and audited and
modified manually.
Link: https://www.kernel.org/doc/html/next/process/deprecated.html#zero-length-and-one-element-arrays [1]
Link: https://www.kernel.org/doc/html/next/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments [2]
Signed-off-by: Erick Archer <erick.archer@outlook.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/AS8PR02MB7237E8469568A59795F1F0408BE12@AS8PR02MB7237.eurprd02.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a deadlock issue found in sungem driver, please refer to the
commit ac0a230f719b ("eth: sungem: remove .ndo_poll_controller to avoid
deadlocks"). The root cause of the issue is that netpoll is in atomic
context and disable_irq() is called by .ndo_poll_controller interface
of sungem driver, however, disable_irq() might sleep. After analyzing
the implementation of fec_poll_controller(), the fec driver should have
the same issue. Due to the fec driver uses NAPI for TX completions, the
.ndo_poll_controller is unnecessary to be implemented in the fec driver,
so fec_poll_controller() can be safely removed.
Fixes: 7f5c6addcdc0 ("net/fec: add poll controller function for fec nic")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20240511062009.652918-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the Renesas RZ/N1 GMAC. This support can make use of a
custom RZ/N1 PCS which is fetched by parsing the pcs-handle device tree
property.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://lore.kernel.org/r/20240513-rzn1-gmac1-v7-6-6acf58b5440d@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the newly introduced pcs_init() and pcs_exit() operations to
create and destroy the PCS instance at a more appropriate moment during
the driver lifecycle, thereby avoiding publishing a network device to
userspace that has not yet finished its PCS initialisation.
There are other similar issues with this driver which remain
unaddressed, but these are out of scope for this patch.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
[rgantois: removed second parameters of new callbacks]
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://lore.kernel.org/r/20240513-rzn1-gmac1-v7-5-6acf58b5440d@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce a mechanism whereby platforms can create their PCS instances
prior to the network device being published to userspace, but after
some of the core stmmac initialisation has been completed. This means
that the data structures that platforms need will be available.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://lore.kernel.org/r/20240513-rzn1-gmac1-v7-4-6acf58b5440d@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A pcs_init() callback will be introduced to stmmac in a future patch. This
new function will be called during the hardware initialization phase.
Instead of separately initializing XPCS and PCS components, let's group all
PCS-related hardware initialization logic in the current
stmmac_xpcs_setup() function.
Rename stmmac_xpcs_setup() to stmmac_pcs_setup() and move the conditional
call to stmmac_xpcs_setup() inside the function itself.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://lore.kernel.org/r/20240513-rzn1-gmac1-v7-3-6acf58b5440d@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the XPCS handler destruction is performed in the
stmmac_mdio_unregister() method. It doesn't look good because the handler
isn't originally created in the corresponding protagonist
stmmac_mdio_unregister(), but in the stmmac_xpcs_setup() function. In
order to have more coherent MDIO and XPCS setup/cleanup procedures,
let's move the DW XPCS destruction to the dedicated stmmac_pcs_clean()
method.
This method will also be used to cleanup PCS hardware using the
pcs_exit() callback that will be introduced to stmmac in a subsequent
patch.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://lore.kernel.org/r/20240513-rzn1-gmac1-v7-2-6acf58b5440d@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
- Add cpufreq pressure feedback for the scheduler
- Rework misfit load-balancing wrt affinity restrictions
- Clean up and simplify the code around ::overutilized and
::overload access.
- Simplify sched_balance_newidle()
- Bump SCHEDSTAT_VERSION to 16 due to a cleanup of CPU_MAX_IDLE_TYPES
handling that changed the output.
- Rework & clean up <asm/vtime.h> interactions wrt arch_vtime_task_switch()
- Reorganize, clean up and unify most of the higher level
scheduler balancing function names around the sched_balance_*()
prefix
- Simplify the balancing flag code (sched_balance_running)
- Miscellaneous cleanups & fixes
* tag 'sched-core-2024-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (50 commits)
sched/pelt: Remove shift of thermal clock
sched/cpufreq: Rename arch_update_thermal_pressure() => arch_update_hw_pressure()
thermal/cpufreq: Remove arch_update_thermal_pressure()
sched/cpufreq: Take cpufreq feedback into account
cpufreq: Add a cpufreq pressure feedback for the scheduler
sched/fair: Fix update of rd->sg_overutilized
sched/vtime: Do not include <asm/vtime.h> header
s390/irq,nmi: Include <asm/vtime.h> header directly
s390/vtime: Remove unused __ARCH_HAS_VTIME_TASK_SWITCH leftover
sched/vtime: Get rid of generic vtime_task_switch() implementation
sched/vtime: Remove confusing arch_vtime_task_switch() declaration
sched/balancing: Simplify the sg_status bitmask and use separate ->overloaded and ->overutilized flags
sched/fair: Rename set_rd_overutilized_status() to set_rd_overutilized()
sched/fair: Rename SG_OVERLOAD to SG_OVERLOADED
sched/fair: Rename {set|get}_rd_overload() to {set|get}_rd_overloaded()
sched/fair: Rename root_domain::overload to ::overloaded
sched/fair: Use helper functions to access root_domain::overload
sched/fair: Check root_domain::overload value before update
sched/fair: Combine EAS check with root_domain::overutilized access
sched/fair: Simplify the continue_balancing logic in sched_balance_newidle()
...
|
|
This driver currently doesn't support any control flags.
Use flow_rule_match_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_match_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240511073705.230507-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We call the build_skb() actually without copying data.
The comment is misleading. So remove it.
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20240511031404.30903-5-xuanzhuo@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now, the premapped mode can be enabled unconditionally.
So we can remove the failover code for merge and small mode.
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20240511031404.30903-4-xuanzhuo@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The virtio-net big mode did not enable premapped mode,
so we did not need to check the unmap. And the subsequent
commit will remove the failover code for failing enable
premapped for merge and small mode. So we need to remove
the checking do_dma code in the big mode path.
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20240511031404.30903-3-xuanzhuo@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now, we have virtio DMA APIs, the driver can be the premapped
mode whatever the virtio core uses dma api or not.
So remove the limit of checking use_dma_api from
virtqueue_set_dma_premapped().
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20240511031404.30903-2-xuanzhuo@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
