| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Update the qmi_wwan driver support for the Rolling
LTE modules.
- VID:PID 33f8:0104, RW101-GL for laptop debug M.2 cards(with RMNET
interface for /Linux/Chrome OS)
0x0104: RMNET, diag, at, pipe
Here are the outputs of usb-devices:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=33f8 ProdID=0104 Rev=05.04
S: Manufacturer=Rolling Wireless S.a.r.l.
S: Product=Rolling Module
S: SerialNumber=ba2eb033
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
Signed-off-by: Vanillan Wang <vanillanwang@163.com>
Link: https://lore.kernel.org/r/20240416120713.24777-1-vanillanwang@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-04-16 (ice)
This series contains updates to ice driver only.
Michal fixes a couple of issues with TC filter parsing; always add match
for src_vsi and remove flag check that could prevent addition of valid
filters.
Marcin adds additional checks for unsupported flower filters.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Fix checking for unsupported keys on non-tunnel device
ice: tc: allow zero flags in parsing tc flower
ice: tc: check src_vsi in case of traffic from VF
====================
Link: https://lore.kernel.org/r/20240416202409.2008383-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux
Pull pwm fixes from Uwe Kleine-König:
"The first patch fixes a regression in the suspend/resume path for the
dwc pwm driver that was introduced in v6.9-rc1 when support for 16
channel devices was added.
The second patch fixes a bunch of device tree binding check warnings"
* tag 'pwm/for-6.9-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
dt-bindings: pwm: mediatek,pwm-disp: Document power-domains property
pwm: dwc: allow suspend/resume for 16 channels
|
|
Convert a variable sized array from [1] to [].
v2: fix up a few more.
v3: integrate comments from Kees.
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Jeff Johnson <quic_jjohnson@quicinc.com> (v2)
Acked-by: Christian König <christian.koenig@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: keescook@chromium.org
|
|
The driver parses a union where the layout up through the first
array is the same, however, the array has different sizes
depending on the elements in the union. Be explicit to
fix the UBSAN checker.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3323
Fixes: df8fc4e934c1 ("kbuild: Enable -fstrict-flex-arrays=3")
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Kees Cook <keescook@chromium.org>
|
|
When we removed the hacky start code check we actually didn't took into
account that *all* VRAM pages needs to be CPU accessible.
Clean up the code and unify the handling into a single helper which
checks if the whole resource is CPU accessible.
The only place where a partial check would make sense is during
eviction, but that is neglitible.
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: aed01a68047b ("drm/amdgpu: Remove TTM resource->start visible VRAM condition v2")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CC: stable@vger.kernel.org
|
|
Verify the parameters of
amdgpu_vm_bo_(map/replace_map/clearing_mappings) in one common place.
Fixes: dc54d3d1744d ("drm/amdgpu: implement AMDGPU_VA_OP_CLEAR v2")
Cc: stable@vger.kernel.org
Reported-by: Vlad Stolyarov <hexed@google.com>
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit b5abd7f983e14054593dc91d6df2aa5f8cc67652.
This change breaks DSC on 4k monitors at 144Hz over USB-C.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3254
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Muhammad Ahmed <ahmed.ahmed@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Charlene Liu <charlene.liu@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
|
|
Fix memory leak due to a leaked mmget reference on an error handling
code path that is triggered when attempting to create KFD processes
while a GPU reset is in progress.
Fixes: 0ab2d7532b05 ("drm/amdkfd: prepare per-process debug enable and disable")
CC: Xiaogang Chen <xiaogang.chen@amd.com>
Signed-off-by: Felix Kuehling <felix.kuehling@amd.com>
Tested-by: Harish Kasiviswanthan <Harish.Kasiviswanthan@amd.com>
Reviewed-by: Mukul Joshi <mukul.joshi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
The majority of those where removed in the commit aed01a68047b
("drm/amdgpu: Remove TTM resource->start visible VRAM condition v2")
But this one was missed because it's working on the resource and not the
BO. Since we also no longer use a fake start address for visible BOs
this will now trigger invalid mapping errors.
v2: also remove the unused variable
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: aed01a68047b ("drm/amdgpu: Remove TTM resource->start visible VRAM condition v2")
CC: stable@vger.kernel.org
Acked-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
BIOS 03.05 still hasn't fixed the spurious IRQ1 issue. As it's still
being worked on there is still a possibility that it won't need to
apply to future BIOS releases.
Add a quirk for BIOS 03.05 as well.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240410141046.433-1-mario.limonciello@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The asid is only erased from the xarray when the vm refcount reaches
zero, however this leads to potential UAF since the xe_vm_get() only
works on a vm with refcount != 0. Since the asid is allocated in the vm
create ioctl, rather erase it when closing the vm, prior to dropping the
potential last ref. This should also work when user closes driver fd
without explicit vm destroy.
Fixes: dd08ebf6c352 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/1594
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: <stable@vger.kernel.org> # v6.8+
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240412113144.259426-4-matthew.auld@intel.com
(cherry picked from commit 83967c57320d0d01ae512f10e79213f81e4bf594)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Add a unreference bo in the error path, to prevent leaking a bo ref.
Return 0 on success to clarify the success path.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 44e694958b95 ("drm/xe/display: Implement display support")
Cc: <stable@vger.kernel.org> # v6.8+
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404090302.68422-1-maarten.lankhorst@linux.intel.com
(cherry picked from commit a2f3d731be3893e730417ae3190760fcaffdf549)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Since [1], dma_alloc_coherent() does not accept requests for GFP_COMP
anymore, even on archs that may be able to fulfill this. Functionality that
relied on the receive buffer being a compound page broke at that point:
The SMC-D protocol, that utilizes the ism device driver, passes receive
buffers to the splice processor in a struct splice_pipe_desc with a
single entry list of struct pages. As the buffer is no longer a compound
page, the splice processor now rejects requests to handle more than a
page worth of data.
Replace dma_alloc_coherent() and allocate a buffer with folio_alloc and
create a DMA map for it with dma_map_page(). Since only receive buffers
on ISM devices use DMA, qualify the mapping as FROM_DEVICE.
Since ISM devices are available on arch s390, only, and on that arch all
DMA is coherent, there is no need to introduce and export some kind of
dma_sync_to_cpu() method to be called by the SMC-D protocol layer.
Analogously, replace dma_free_coherent by a two step dma_unmap_page,
then folio_put to free the receive buffer.
[1] https://lore.kernel.org/all/20221113163535.884299-1-hch@lst.de/
Fixes: c08004eede4b ("s390/ism: don't pass bogus GFP_ flags to dma_alloc_coherent")
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The entropy accounting changes a static key when the RNG has
initialized, since it only ever initializes once. Static key changes,
however, cannot be made from atomic context, so depending on where the
last creditable entropy comes from, the static key change might need to
be deferred to a worker.
Previously the code used the execute_in_process_context() helper
function, which accounts for whether or not the caller is
in_interrupt(). However, that doesn't account for the case where the
caller is actually in process context but is holding a spinlock.
This turned out to be the case with input_handle_event() in
drivers/input/input.c contributing entropy:
[<ffffffd613025ba0>] die+0xa8/0x2fc
[<ffffffd613027428>] bug_handler+0x44/0xec
[<ffffffd613016964>] brk_handler+0x90/0x144
[<ffffffd613041e58>] do_debug_exception+0xa0/0x148
[<ffffffd61400c208>] el1_dbg+0x60/0x7c
[<ffffffd61400c000>] el1h_64_sync_handler+0x38/0x90
[<ffffffd613011294>] el1h_64_sync+0x64/0x6c
[<ffffffd613102d88>] __might_resched+0x1fc/0x2e8
[<ffffffd613102b54>] __might_sleep+0x44/0x7c
[<ffffffd6130b6eac>] cpus_read_lock+0x1c/0xec
[<ffffffd6132c2820>] static_key_enable+0x14/0x38
[<ffffffd61400ac08>] crng_set_ready+0x14/0x28
[<ffffffd6130df4dc>] execute_in_process_context+0xb8/0xf8
[<ffffffd61400ab30>] _credit_init_bits+0x118/0x1dc
[<ffffffd6138580c8>] add_timer_randomness+0x264/0x270
[<ffffffd613857e54>] add_input_randomness+0x38/0x48
[<ffffffd613a80f94>] input_handle_event+0x2b8/0x490
[<ffffffd613a81310>] input_event+0x6c/0x98
According to Guoyong, it's not really possible to refactor the various
drivers to never hold a spinlock there. And in_atomic() isn't reliable.
So, rather than trying to be too fancy, just punt the change in the
static key to a workqueue always. There's basically no drawback of doing
this, as the code already needed to account for the static key not
changing immediately, and given that it's just an optimization, there's
not exactly a hurry to change the static key right away, so deferal is
fine.
Reported-by: Guoyong Wang <guoyong.wang@mediatek.com>
Cc: stable@vger.kernel.org
Fixes: f5bda35fba61 ("random: use static branch for crng_ready()")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
When an UART is opened that still has .throttled set from a previous
open, the RX interrupt is enabled but the irq handler doesn't consider
it. This easily results in a stuck irq with the effect to occupy the CPU
in a tight loop.
So reset the throttle state in .startup() to ensure that RX irqs are
handled.
Fixes: d1ec8a2eabe9 ("serial: stm32: update throttle and unthrottle ops for dma mode")
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/a784f80d3414f7db723b2ec66efc56e1ad666cbf.1713344161.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If there is a stuck irq that the handler doesn't address, returning
IRQ_HANDLED unconditionally makes it impossible for the irq core to
detect the problem and disable the irq. So only return IRQ_HANDLED if
an event was handled.
A stuck irq is still problematic, but with this change at least it only
makes the UART nonfunctional instead of occupying the (usually only) CPU
by 100% and so stall the whole machine.
Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/5f92603d0dfd8a5b8014b2b10a902d91e0bb881f.1713344161.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The "MT7988A Wi-Fi 7 Generation Router Platform: Datasheet (Open Version)
v0.1" document shows bits 16 to 18 as the MIRROR_PORT field of the CPU
forward control register. Currently, the MT7530 DSA subdriver configures
bits 0 to 2 of the CPU forward control register which breaks the port
mirroring feature for the MT7988 SoC switch.
Fix this by using the MT7531_MIRROR_PORT_GET() and MT7531_MIRROR_PORT_SET()
macros which utilise the correct bits.
Fixes: 110c18bfed41 ("net: dsa: mt7530: introduce driver for MT7988 built-in switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This switch intellectual property provides a bit on the ARL global control
register which controls allowing mirroring frames which are received on the
local port (monitor port). This bit is unset after reset.
This ability must be enabled to fully support the port mirroring feature on
this switch intellectual property.
Therefore, this patch fixes the traffic not being reflected on a port,
which would be configured like below:
tc qdisc add dev swp0 clsact
tc filter add dev swp0 ingress matchall skip_sw \
action mirred egress mirror dev swp0
As a side note, this configuration provides the hairpinning feature for a
single port.
Fixes: 37feab6076aa ("net: dsa: mt7530: add support for port mirroring")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fibocom FM650/FG650 are 5G modems with ECM/NCM/RNDIS/MBIM modes.
This patch adds support to all 4 modes.
In all 4 modes, the first serial port is the AT console while the other
3 appear to be diagnostic interfaces for dumping modem logs.
usb-devices output for all modes:
ECM:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 5 Spd=5000 MxCh= 0
D: Ver= 3.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=2cb7 ProdID=0a04 Rev=04.04
S: Manufacturer=Fibocom Wireless Inc.
S: Product=FG650 Module
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 5 Cfg#= 1 Atr=c0 MxPwr=504mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
NCM:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=5000 MxCh= 0
D: Ver= 3.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=2cb7 ProdID=0a05 Rev=04.04
S: Manufacturer=Fibocom Wireless Inc.
S: Product=FG650 Module
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=c0 MxPwr=504mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0d Prot=00 Driver=cdc_ncm
E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=01 Driver=cdc_ncm
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
RNDIS:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=5000 MxCh= 0
D: Ver= 3.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=2cb7 ProdID=0a06 Rev=04.04
S: Manufacturer=Fibocom Wireless Inc.
S: Product=FG650 Module
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=c0 MxPwr=504mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
MBIM:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=5000 MxCh= 0
D: Ver= 3.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=2cb7 ProdID=0a07 Rev=04.04
S: Manufacturer=Fibocom Wireless Inc.
S: Product=FG650 Module
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=c0 MxPwr=504mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
vhost_worker will call tun call backs to receive packets. If too many
illegal packets arrives, tun_do_read will keep dumping packet contents.
When console is enabled, it will costs much more cpu time to dump
packet and soft lockup will be detected.
net_ratelimit mechanism can be used to limit the dumping rate.
PID: 33036 TASK: ffff949da6f20000 CPU: 23 COMMAND: "vhost-32980"
#0 [fffffe00003fce50] crash_nmi_callback at ffffffff89249253
#1 [fffffe00003fce58] nmi_handle at ffffffff89225fa3
#2 [fffffe00003fceb0] default_do_nmi at ffffffff8922642e
#3 [fffffe00003fced0] do_nmi at ffffffff8922660d
#4 [fffffe00003fcef0] end_repeat_nmi at ffffffff89c01663
[exception RIP: io_serial_in+20]
RIP: ffffffff89792594 RSP: ffffa655314979e8 RFLAGS: 00000002
RAX: ffffffff89792500 RBX: ffffffff8af428a0 RCX: 0000000000000000
RDX: 00000000000003fd RSI: 0000000000000005 RDI: ffffffff8af428a0
RBP: 0000000000002710 R8: 0000000000000004 R9: 000000000000000f
R10: 0000000000000000 R11: ffffffff8acbf64f R12: 0000000000000020
R13: ffffffff8acbf698 R14: 0000000000000058 R15: 0000000000000000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#5 [ffffa655314979e8] io_serial_in at ffffffff89792594
#6 [ffffa655314979e8] wait_for_xmitr at ffffffff89793470
#7 [ffffa65531497a08] serial8250_console_putchar at ffffffff897934f6
#8 [ffffa65531497a20] uart_console_write at ffffffff8978b605
#9 [ffffa65531497a48] serial8250_console_write at ffffffff89796558
#10 [ffffa65531497ac8] console_unlock at ffffffff89316124
#11 [ffffa65531497b10] vprintk_emit at ffffffff89317c07
#12 [ffffa65531497b68] printk at ffffffff89318306
#13 [ffffa65531497bc8] print_hex_dump at ffffffff89650765
#14 [ffffa65531497ca8] tun_do_read at ffffffffc0b06c27 [tun]
#15 [ffffa65531497d38] tun_recvmsg at ffffffffc0b06e34 [tun]
#16 [ffffa65531497d68] handle_rx at ffffffffc0c5d682 [vhost_net]
#17 [ffffa65531497ed0] vhost_worker at ffffffffc0c644dc [vhost]
#18 [ffffa65531497f10] kthread at ffffffff892d2e72
#19 [ffffa65531497f50] ret_from_fork at ffffffff89c0022f
Fixes: ef3db4a59542 ("tun: avoid BUG, dump packet on GSO errors")
Signed-off-by: Lei Chen <lei.chen@smartx.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20240415020247.2207781-1-lei.chen@smartx.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The DSI device for the panel was registered by the DSI host, so it is an
error to unregister it from the panel driver. Drop the call to
mipi_dsi_device_unregister().
Fixes: ea4f9975625a ("drm/panel: Add support for Novatek NT36672E panel driver")
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404-drop-panel-unregister-v1-2-9f56953c5fb9@linaro.org
|
|
The DSI device for the panel was registered by the DSI host, so it is an
error to unregister it from the panel driver. Drop the call to
mipi_dsi_device_unregister().
Fixes: c7f66d32dd43 ("drm/panel: add support for rm69299 visionox panel")
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404-drop-panel-unregister-v1-1-9f56953c5fb9@linaro.org
|
|
Add missing FLOW_DISSECTOR_KEY_ENC_* checks to TC flower filter parsing.
Without these checks, it would be possible to add filters with tunnel
options on non-tunnel devices. enc_* options are only valid for tunnel
devices.
Example:
devlink dev eswitch set $PF1_PCI mode switchdev
echo 1 > /sys/class/net/$PF1/device/sriov_numvfs
tc qdisc add dev $VF1_PR ingress
ethtool -K $PF1 hw-tc-offload on
tc filter add dev $VF1_PR ingress flower enc_ttl 12 skip_sw action drop
Fixes: 9e300987d4a8 ("ice: VXLAN and Geneve TC support")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The check for flags is done to not pass empty lookups to adding switch
rule functions. Since metadata is always added to lookups there is no
need to check against the flag.
It is also fixing the problem with such rule:
$ tc filter add dev gtp_dev ingress protocol ip prio 0 flower \
enc_dst_port 2123 action drop
Switch block in case of GTP can't parse the destination port, because it
should always be set to GTP specific value. The same with ethertype. The
result is that there is no other matching criteria than GTP tunnel. In
this case flags is 0, rule can't be added only because of defensive
check against flags.
Fixes: 9a225f81f540 ("ice: Support GTP-U and GTP-C offload in switchdev")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In case of traffic going from the VF (so ingress for port representor)
source VSI should be consider during packet classification. It is
needed for hardware to not match packets from different ports with
filters added on other port.
It is only for "from VF" traffic, because other traffic direction
doesn't have source VSI.
Set correct ::src_vsi in rule_info to pass it to the hardware filter.
For example this rule should drop only ipv4 packets from eth10, not from
the others VF PRs. It is needed to check source VSI in this case.
$tc filter add dev eth10 ingress protocol ip flower skip_sw action drop
Fixes: 0d08a441fb1a ("ice: ndo_setup_tc implementation for PF")
Reviewed-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Here is the list of the MAC capabilities specific to the particular DW MAC
IP-cores currently supported by the driver:
DW MAC100: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100
DW GMAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000
Allwinner sun8i MAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000
DW QoS Eth: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000 | MAC_2500FD
if there is more than 1 active Tx/Rx queues:
MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10FD | MAC_100FD | MAC_1000FD | MAC_2500FD
DW XGMAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_1000FD | MAC_2500FD | MAC_5000FD | MAC_10000FD
DW XLGMAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_1000FD | MAC_2500FD | MAC_5000FD | MAC_10000FD |
MAC_25000FD | MAC_40000FD | MAC_50000FD | MAC_100000FD
As you can see there are only two common capabilities:
MAC_ASYM_PAUSE | MAC_SYM_PAUSE.
Meanwhile what is currently implemented defines 10/100/1000 link speeds
for all IP-cores, which is definitely incorrect for DW MAC100, DW XGMAC
and DW XLGMAC devices.
Seeing the flow-control is implemented as a callback for each MAC IP-core
(see dwmac100_flow_ctrl(), dwmac1000_flow_ctrl(), sun8i_dwmac_flow_ctrl(),
etc) and since the MAC-specific setup() method is supposed to be called
for each available DW MAC-based device, the capabilities initialization
can be freely moved to these setup() functions, thus correctly setting up
the MAC-capabilities for each IP-core (including the Allwinner Sun8i). A
new stmmac_link::caps field was specifically introduced for that so to
have all link-specific info preserved in a single structure.
Note the suggested change fixes three earlier commits at a time. The
commit 5b0d7d7da64b ("net: stmmac: Add the missing speeds that XGMAC
supports") permitted the 10-100 link speeds and 1G half-duplex mode for DW
XGMAC IP-core even though it doesn't support them. The commit df7699c70c1b
("net: stmmac: Do not cut down 1G modes") incorrectly added the MAC1000
capability to the DW MAC100 IP-core. Similarly to the DW XGMAC the commit
8a880936e902 ("net: stmmac: Add XLGMII support") incorrectly permitted the
10-100 link speeds and 1G half-duplex mode for DW XLGMAC IP-core.
Fixes: 5b0d7d7da64b ("net: stmmac: Add the missing speeds that XGMAC supports")
Fixes: df7699c70c1b ("net: stmmac: Do not cut down 1G modes")
Fixes: 8a880936e902 ("net: stmmac: Add XLGMII support")
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
It's possible to have the maximum link speed being artificially limited on
the platform-specific basis. It's done either by setting up the
plat_stmmacenet_data::max_speed field or by specifying the "max-speed"
DT-property. In such cases it's required that any specific
MAC-capabilities re-initializations would take the limit into account. In
particular the link speed capabilities may change during the number of
active Tx/Rx queues re-initialization. But the currently implemented
procedure doesn't take the speed limit into account.
Fix that by calling phylink_limit_mac_speed() in the
stmmac_reinit_queues() method if the speed limitation was required in the
same way as it's done in the stmmac_phy_setup() function.
Fixes: 95201f36f395 ("net: stmmac: update MAC capabilities when tx queues are updated")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There are three DW MAC IP-cores which can have the multiple Tx/Rx queues
enabled:
DW GMAC v3.7+ with AV feature,
DW QoS Eth v4.x/v5.x,
DW XGMAC/XLGMAC
Based on the respective HW databooks, only the DW QoS Eth IP-core doesn't
support the half-duplex link mode in case if more than one queues enabled:
"In multiple queue/channel configurations, for half-duplex operation,
enable only the Q0/CH0 on Tx and Rx. For single queue/channel in
full-duplex operation, any queue/channel can be enabled."
The rest of the IP-cores don't have such constraint. Thus in order to have
the constraint applied for the DW QoS Eth MACs only, let's move the it'
implementation to the respective MAC-capabilities getter and make sure the
getter is called in the queues re-init procedure.
Fixes: b6cfffa7ad92 ("stmmac: fix DMA channel hang in half-duplex mode")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
No new changes will be added for minor version 2. Change the minor
version number to 2 and stop displaying log message for unsupported
minor version 2.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20240415220625.2828339-1-srinivas.pandruvada@linux.intel.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add Granite Rapids-D to hpm_cpu_ids, so that MSR 0x54 can be used.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20240415212853.2820470-1-srinivas.pandruvada@linux.intel.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
ROG Zephyrus G14 advertises support for SPS notifications to the
BIOS but doesn't actually use them. Instead the asus-nb-wmi driver
utilizes such events.
Add a quirk to prevent the system from registering for ACPI platform
profile when this system is found to avoid conflicts.
Reported-by: al0uette@outlook.com
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218685
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20240410140956.385-3-mario.limonciello@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
In the event of a BIOS bug add infrastructure that will be utilized
to override the return value for supported_funcs to avoid enabling
features.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20240410140956.385-2-mario.limonciello@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
ASUS ROG Zephyrus G14 doesn't have _CRS in AMDI0102 device and so
there are no resources to walk. This is expected behavior because
it doesn't support Smart PC. Decrease error message to debug.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218685
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240410140956.385-1-mario.limonciello@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
I didn't pay close enough attention the last time I tried to fix this
problem - while we currently do correctly take care to make sure we don't
probe a connected eDP port more then once, we don't do the same thing for
eDP ports we found to be disconnected.
So, fix this and make sure we only ever probe eDP ports once and then leave
them at that connector state forever (since without HPD, it's not going to
change on its own anyway). This should get rid of the last few GSP errors
getting spit out during runtime suspend and resume on some machines, as we
tried to reprobe eDP ports in response to ACPI hotplug probe events.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404233736.7946-3-lyude@redhat.com
(cherry picked from commit fe6660b661c3397af0867d5d098f5b26581f1290)
|
|
GSP has its own state for keeping track of whether or not a given display
connector is plugged in or not, and enforces this state on the driver. In
particular, AUX transactions on a DisplayPort connector which GSP says is
disconnected can never succeed - and can in some cases even cause
unexpected timeouts, which can trickle up to cause other problems. A good
example of this is runtime power management: where we can actually get
stuck trying to resume the GPU if a userspace application like fwupd tries
accessing a drm_aux_dev for a disconnected port. This was an issue I hit a
few times with my Slimbook Executive 16 - where trying to offload something
to the discrete GPU would wake it up, and then potentially cause it to
timeout as fwupd tried to immediately access the dp_aux_dev nodes for
nouveau.
Likewise: we don't really have any cases I know of where we'd want to
ignore this state and try an aux transaction anyway - and failing pointless
aux transactions immediately can even speed things up. So - let's start
enabling/disabling the aux bus in nouveau_dp_detect() to fix this. We
enable the aux bus during connector probing, and leave it enabled if we
discover something is actually on the connector. Otherwise, we just shut it
off.
This should fix some people's runtime PM issues (like myself), and also get
rid of quite of a lot of GSP error spam in dmesg.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404233736.7946-2-lyude@redhat.com
(cherry picked from commit 9c8a10bf1f3467b2c16f6848249bdc7692ace825)
|
|
The commit 509433d8146c ("drm/v3d: Expose the total GPU usage stats on sysfs")
introduced the calculation of global GPU stats. For the regards, it used
the already existing infrastructure provided by commit 09a93cc4f7d1 ("drm/v3d:
Implement show_fdinfo() callback for GPU usage stats"). While adding
global GPU stats calculation ability, the author forgot to delete the
existing one.
Currently, the value of `enabled_ns` is incremented twice by the end of
the job, when it should be added just once. Therefore, delete the
leftovers from commit 509433d8146c ("drm/v3d: Expose the total GPU usage
stats on sysfs").
Fixes: 509433d8146c ("drm/v3d: Expose the total GPU usage stats on sysfs")
Reported-by: Tvrtko Ursulin <tursulin@igalia.com>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Reviewed-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240403203517.731876-2-mcanal@igalia.com
|
|
The table of primary plane formats wasn't sorted at all, leading to
applications picking our least desirable formats by defaults.
Sort the primary plane formats according to our order of preference.
Nice side-effect of this change is that it makes IGT's kms_atomic
plane-invalid-params pass because the test picks the first format
which for vmwgfx was DRM_FORMAT_XRGB1555 and uses fb's with odd sizes
which make Pixman, which IGT depends on assert due to the fact that our
16bpp formats aren't 32 bit aligned like Pixman requires all formats
to be.
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Fixes: 36cc79bc9077 ("drm/vmwgfx: Add universal plane support")
Cc: Broadcom internal kernel review list <bcm-kernel-feedback-list@broadcom.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.12+
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240412025511.78553-6-zack.rusin@broadcom.com
|
|
The conditional was supposed to prevent enabling of a crtc state
without a set primary plane. Accidently it also prevented disabling
crtc state with a set primary plane. Neither is correct.
Fix the conditional and just driver-warn when a crtc state has been
enabled without a primary plane which will help debug broken userspace.
Fixes IGT's kms_atomic_interruptible and kms_atomic_transition tests.
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Fixes: 06ec41909e31 ("drm/vmwgfx: Add and connect CRTC helper functions")
Cc: Broadcom internal kernel review list <bcm-kernel-feedback-list@broadcom.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.12+
Reviewed-by: Ian Forbes <ian.forbes@broadcom.com>
Reviewed-by: Martin Krastev <martin.krastev@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240412025511.78553-5-zack.rusin@broadcom.com
|
|
vmwgfx never supported prime import of external buffers. Furthermore the
driver exposes two different objects to userspace: vmw_surface's and
gem buffers but prime import/export only worked with vmw_surfaces.
Because gem buffers are used through the dumb_buffer interface this meant
that the driver created buffers couldn't have been prime exported or
imported.
Fix prime import/export. Makes IGT's kms_prime pass.
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Fixes: 8afa13a0583f ("drm/vmwgfx: Implement DRIVER_GEM")
Cc: <stable@vger.kernel.org> # v6.6+
Reviewed-by: Martin Krastev <martin.krastev@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240412025511.78553-4-zack.rusin@broadcom.com
|
|
With 16 channel pwm support, we're registering two instances of pwm_chip
with 8 channels each. We need to update PM functions to use both instances
of pwm_chip during power state transitions.
Introduce struct dwc_pwm_drvdata and use it as driver_data, which will
maintain both instances of pwm_chip along with dwc_pwm_info and allow us
to use them inside suspend/resume handles.
Fixes: ebf2c89eb95e ("pwm: dwc: Add 16 channel support for Intel Elkhart Lake")
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240415074051.14681-1-raag.jadav@intel.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
|
|
We only pool write combined and uncached allocations because they
require extra overhead on allocation and release.
If we also pool cached NUMA it not only means some extra unnecessary
overhead, but also that under memory pressure it can happen that
pages from the wrong NUMA node enters the pool and are re-used
over and over again.
This can lead to performance reduction after running into memory
pressure.
v2: restructure and cleanup the code a bit from the internal hack to
test this.
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: 4482d3c94d7f ("drm/ttm: add NUMA node id to the pool")
CC: stable@vger.kernel.org
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415134821.1919-1-christian.koenig@amd.com
|
|
Upon reviewing the flower control flags handling in
this driver, I notice that the key wasn't being used,
only the mask.
Ie. `tc flower ... ip_flags nofrag` was hardware
offloaded as `... ip_flags frag`.
Only compile tested, no access to HW.
Fixes: c672e3727989 ("octeontx2-pf: Add support to filter packet based on IP fragment")
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When Output Resource (dcb->or) value is assigned in
fabricate_dcb_output(), there may be out of bounds access to
dac_users array in case dcb->or is zero because ffs(dcb->or) is
used as index there.
The 'or' argument of fabricate_dcb_output() must be interpreted as a
number of bit to set, not value.
Utilize macros from 'enum nouveau_or' in calls instead of hardcoding.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 2e5702aff395 ("drm/nouveau: fabricate DCB encoder table for iMac G4")
Fixes: 670820c0e6a9 ("drm/nouveau: Workaround incorrect DCB entry on a GeForce3 Ti 200.")
Signed-off-by: Mikhail Kobuk <m.kobuk@ispras.ru>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240411110854.16701-1-m.kobuk@ispras.ru
|
|
Running a lot of VK CTS in parallel against nouveau, once every
few hours you might see something like this crash.
BUG: kernel NULL pointer dereference, address: 0000000000000008
PGD 8000000114e6e067 P4D 8000000114e6e067 PUD 109046067 PMD 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 7 PID: 53891 Comm: deqp-vk Not tainted 6.8.0-rc6+ #27
Hardware name: Gigabyte Technology Co., Ltd. Z390 I AORUS PRO WIFI/Z390 I AORUS PRO WIFI-CF, BIOS F8 11/05/2021
RIP: 0010:gp100_vmm_pgt_mem+0xe3/0x180 [nouveau]
Code: c7 48 01 c8 49 89 45 58 85 d2 0f 84 95 00 00 00 41 0f b7 46 12 49 8b 7e 08 89 da 42 8d 2c f8 48 8b 47 08 41 83 c7 01 48 89 ee <48> 8b 40 08 ff d0 0f 1f 00 49 8b 7e 08 48 89 d9 48 8d 75 04 48 c1
RSP: 0000:ffffac20c5857838 EFLAGS: 00010202
RAX: 0000000000000000 RBX: 00000000004d8001 RCX: 0000000000000001
RDX: 00000000004d8001 RSI: 00000000000006d8 RDI: ffffa07afe332180
RBP: 00000000000006d8 R08: ffffac20c5857ad0 R09: 0000000000ffff10
R10: 0000000000000001 R11: ffffa07af27e2de0 R12: 000000000000001c
R13: ffffac20c5857ad0 R14: ffffa07a96fe9040 R15: 000000000000001c
FS: 00007fe395eed7c0(0000) GS:ffffa07e2c980000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 000000011febe001 CR4: 00000000003706f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
...
? gp100_vmm_pgt_mem+0xe3/0x180 [nouveau]
? gp100_vmm_pgt_mem+0x37/0x180 [nouveau]
nvkm_vmm_iter+0x351/0xa20 [nouveau]
? __pfx_nvkm_vmm_ref_ptes+0x10/0x10 [nouveau]
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
? __lock_acquire+0x3ed/0x2170
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
nvkm_vmm_ptes_get_map+0xc2/0x100 [nouveau]
? __pfx_nvkm_vmm_ref_ptes+0x10/0x10 [nouveau]
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
nvkm_vmm_map_locked+0x224/0x3a0 [nouveau]
Adding any sort of useful debug usually makes it go away, so I hand
wrote the function in a line, and debugged the asm.
Every so often pt->memory->ptrs is NULL. This ptrs ptr is set in
the nv50_instobj_acquire called from nvkm_kmap.
If Thread A and Thread B both get to nv50_instobj_acquire around
the same time, and Thread A hits the refcount_set line, and in
lockstep thread B succeeds at refcount_inc_not_zero, there is a
chance the ptrs value won't have been stored since refcount_set
is unordered. Force a memory barrier here, I picked smp_mb, since
we want it on all CPUs and it's write followed by a read.
v2: use paired smp_rmb/smp_wmb.
Cc: <stable@vger.kernel.org>
Fixes: be55287aa5ba ("drm/nouveau/imem/nv50: embed nvkm_instobj directly into nv04_instobj")
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240411011510.2546857-1-airlied@gmail.com
|
|
EM060K_129, EM060K_12a, EM060K_12b and EM0060K_12c are EM060K's sub-models,
having the same name "Quectel EM060K-GL" and the same interface layout.
MBIM + GNSS + DIAG + NMEA + AT + QDSS + DPL
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0129 Rev= 5.04
S: Manufacturer=Quectel
S: Product=Quectel EM060K-GL
S: SerialNumber=f6fa08b6
C:* #Ifs= 8 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none)
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=8f(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Jerry Meng <jerry-meng@foxmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Update the USB serial option driver support for the Fibocom
FM135-GL LTE modules.
- VID:PID 2cb7:0115, FM135-GL for laptop debug M.2 cards(with MBIM
interface for /Linux/Chrome OS)
0x0115: mbim, diag, at, pipe
Here are the outputs of usb-devices:
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2cb7 ProdID=0115 Rev=05.15
S: Manufacturer=Fibocom Wireless Inc.
S: Product=Fibocom Module
S: SerialNumber=12345678
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: bolan wang <bolan.wang@fibocom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus
Mika writes:
thunderbolt: Fixes for v6.9-rc5
This includes following USB4/Thunderbolt fixes for v6.9-rc5:
- Avoid creating DisplayPort tunnels for the adapters on the same router
- Correct wake configurations after device router unplug
- Fix immediate wake when "wakeup_count" is used to enter system sleep.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Avoid notify PM core about runtime PM resume
thunderbolt: Fix wake configurations after device unplug
thunderbolt: Do not create DisplayPort tunnels on adapters of the same router
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Ingo Molnar:
"Fix a bug in the GIC irqchip driver"
* tag 'irq-urgent-2024-04-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Fix VSYNC referencing an unmapped VPE on GIC v4.1
|
|
Pull virtio bugfixes from Michael Tsirkin:
"Some small, obvious (in hindsight) bugfixes:
- new ioctl in vhost-vdpa has a wrong # - not too late to fix
- vhost has apparently been lacking an smp_rmb() - due to code
duplication :( The duplication will be fixed in the next merge
cycle, this is a minimal fix
- an error message in vhost talks about guest moving used index -
which of course never happens, guest only ever moves the available
index
- i2c-virtio didn't set the driver owner so it did not get refcounted
correctly"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost: correct misleading printing information
vhost-vdpa: change ioctl # for VDPA_GET_VRING_SIZE
virtio: store owner from modules with register_virtio_driver()
vhost: Add smp_rmb() in vhost_enable_notify()
vhost: Add smp_rmb() in vhost_vq_avail_empty()
|
