| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-11-04
This series includes:
From Huy: dscp to priority mapping for Ethernet packet.
===================================================
First six patches enable differentiated services code point (dscp) to
priority mapping for Ethernet packet. Once this feature is
enabled, the packet is routed to the corresponding priority based on its
dscp. User can combine this feature with priority flow control (pfc)
feature to have priority flow control based on the dscp.
Firmware interface:
Mellanox firmware provides two control knobs for this feature:
QPTS register allow changing the trust state between dscp and
pcp mode. The default is pcp mode. Once in dscp mode, firmware will
route the packet based on its dscp value if the dscp field exists.
QPDPM register allow mapping a specific dscp (0 to 63) to a
specific priority (0 to 7). By default, all the dscps are mapped to
priority zero.
Software interface:
This feature is controlled via application priority TLV. IEEE
specification P802.1Qcd/D2.1 defines priority selector id 5 for
application priority TLV. This APP TLV selector defines DSCP to priority
map. This APP TLV can be sent by the switch or can be set locally using
software such as lldptool. In mlx5 drivers, we add the support for net
dcb's getapp and setapp call back. Mlx5 driver only handles the selector
id 5 application entry (dscp application priority application entry).
If user sends multiple dscp to priority APP TLV entries on the same
dscp, the last sent one will take effect. All the previous sent will be
deleted.
The firmware trust state (in QPTS register) is changed based on the
number of dscp to priority application entries. When the first dscp to
priority application entry is added by the user, the trust state is
changed to dscp. When the last dscp to priority application entry is
deleted by the user, the trust state is changed to pcp.
When the port is in DSCP trust state, the transmit queue is selected
based on the dscp of the skb.
When the port is in DSCP trust state and vport inline mode is not NONE,
firmware requires mlx5 driver to copy the IP header to the
wqe ethernet segment inline header if the skb has it.
This is done by changing the transmit queue sq's min inline mode to L3.
Note that the min inline mode of sqs that belong to other features
such as xdpsq, icosq are not modified.
===================================================
Plus to the dscp series, some small misc changes are include as well:
From Inbar, Ethtool msglvl support and some debug prints in DCBNL logic
From Or Gerlitz, Enlarge the NIC TC offload table size
From Rabie, Initialize destination_flow struct to 0
From Feras, Add inner TTC table to IPoIB flow steering
From Tal, Enable CQE based moderation on TX CQ
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support in the driver ethtool ops to modify the NFP FEC modes.
The FEC modes can be set for vNIC associated with physical ports or
for MAC representor netdevs.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement helpers to determine and modify FEC modes via the NSP.
The NSP advertises FEC capabilities on a per port basis and provides
support for:
* Auto mode selection
* Reed Solomon
* BaseR
* None/Off
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since it is now safe to modify link settings for representors, we can
attach the get/set link settings ndos to it. The get/set link settings
are nfp_port based operations.
If a port becomes invalid, the representor will be removed in the same
way a vnic would be.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the NSP port table has been refreshed, resync the representor state
with the new port information. At the moment, this only entails looking
for invalid ports and killing off representors associated with them.
The repr instance becomes NULL which is safe since the app accessor
function for reprs returns NULL when it cannot access a repr.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The criteria that reprs cannot be replaced with another new set of reprs
has been removed. This check is not needed since the only use case that
could exercise this at the moment, would be to modify the number of
SRIOV VFs without first disabling them. This case is explicitly
disallowed in any case and subsequent patches in this series
need to be able to replace the running set of reprs.
All cases where the return code used to be checked for the
nfp_app_reprs_set function have been removed.
As stated above, it is not possible for the current code to encounter a
case where reprs exist and need to be replaced.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent management FW images can perform full reinit of MAC cores
without requiring a reboot. When loading the driver check if there
are changes pending and if so call NSP MAC reinit. Full application
FW reload is still required, and all MACs need to be reinited at the
same time (not only the ones which have been reconfigured, and thus
potentially causing disruption to unrelated netdevs) therefore for
now changing MAC config without reloading the driver still remains
future work.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Tested-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Matthias reports:
nfp_eth_set_bit_config() is marked as __always_inline to allow gcc to
identify the 'mask' parameter as known to be constant at compile time,
which is required to use the FIELD_GET() macro.
The forced inlining does the trick for gcc, but for kernel builds with
clang it results in undefined symbols:
drivers/net/ethernet/netronome/nfp/nfpcore/nfp_nsp_eth.o: In function
`__nfp_eth_set_aneg':
drivers/net/ethernet/netronome/nfp/nfpcore/nfp_nsp_eth.c:(.text+0x787):
undefined reference to `__compiletime_assert_492'
drivers/net/ethernet/netronome/nfp/nfpcore/nfp_nsp_eth.c:(.text+0x7b1):
undefined reference to `__compiletime_assert_496'
These __compiletime_assert_xyx() calls would have been optimized away
if
the compiler had seen 'mask' as a constant.
Add a macro to extract the mask and shift and pass those to
nfp_eth_set_bit_config() separately.
Reported-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Tested-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev->rx_dropped was including packets dropped by napi_gro_receive.
If a packet is dropped by network stack, it should not be counted under
driver Rx dropped.
Made necessary changes to not include network stack drops under
netdev->rx_dropped.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following steps are taken in the driver to offload an XDP program:
XDP_SETUP_PROG:
* prepare:
- allocate program state;
- run verifier (bpf_analyzer());
- run translation;
* load:
- stop old program if needed;
- load program;
- enable BPF if not enabled;
* clean up:
- free program image.
With new infrastructure the flow will look like this:
BPF_OFFLOAD_VERIFIER_PREP:
- allocate program state;
BPF_OFFLOAD_TRANSLATE:
- run translation;
XDP_SETUP_PROG:
- stop old program if needed;
- load program;
- enable BPF if not enabled;
BPF_OFFLOAD_DESTROY:
- free program image.
Take advantage of the new infrastructure. Allocation of driver
metadata has to be moved from jit.c to offload.c since it's now
done at a different stage. Since there is no separate driver
private data for verification step, move temporary nfp_meta
pointer into nfp_prog. We will now use user space context
offsets.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct nfp_prog is currently only used internally by the translator.
This means there is a lot of parameter passing going on, between
the translator and different stages of offload. Simplify things
by allocating nfp_prog in offload.c already.
We will now use kmalloc() to allocate the program area and only
DMA map it for the time of loading (instead of allocating DMA
coherent memory upfront).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of offload/translation prepare logic will be moved to
offload.c. To help git generate more reasonable diffs
move nfp_prog_prepare() and nfp_prog_free() functions
there as a first step.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware supports live replacement of programs for quite some
time now. Remove the software-fallback related logic and
depend on the FW for program replace. Seamless reload will
become a requirement if maps are present, anyway.
Load and start stages have to be split now, since replace
only needs a load, start has already been done on add.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently create a fake cls_bpf offload object when we want
to offload XDP. Simplify and clarify the code by moving the
TC/XDP specific logic out of common offload code. This is easy
now that we don't support legacy TC actions. We only need the
bpf program and state of the skip_sw flag.
Temporarily set @code to NULL in nfp_net_bpf_offload(), compilers
seem to have trouble recognizing it's always initialized. Next
patches will eliminate that variable.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BPF offload's main header does not need to include nfp_net.h.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The register renumbering was removed and will not be coming back
in its old, naive form, given that it would be fundamentally
incompatible with calling functions. Remove the leftovers.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only support BPF_PROG_TYPE_SCHED_CLS programs in direct
action mode. This simplifies preparing the offload since
there will now be only one mode of operation for that type
of program. We need to know the attachment mode type of
cls_bpf programs, because exit codes are interpreted
differently for legacy vs DA mode.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ndo_xdp is a control path callback for setting up XDP in the
driver. We can reuse it for other forms of communication
between the eBPF stack and the drivers. Rename the callback
and associated structures and definitions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the swap macro and remove unnecessary variables skb and cnt.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114893
Addresses-Coverity-ID: 114894
Addresses-Coverity-ID: 114895
Addresses-Coverity-ID: 114896
Addresses-Coverity-ID: 114897
Addresses-Coverity-ID: 114898
Addresses-Coverity-ID: 114899
Addresses-Coverity-ID: 114900
Addresses-Coverity-ID: 114901
Addresses-Coverity-ID: 114902
Addresses-Coverity-ID: 114903
Addresses-Coverity-ID: 114904
Addresses-Coverity-ID: 114905
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can now build this driver on ARM, so I ran into a randconfig build
warning that presumably had existed on powerpc already.
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c: In function 'sg_fd_to_skb':
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:1712:18: error: 'skb' may be used uninitialized in this function [-Werror=maybe-uninitialized]
I'm slightly changing the logic here, to make it obvious to the
compiler that 'skb' is always initialized.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By using CQE based moderation on TX CQ we can reduce the number of TX
interrupt rate. Besides the benefit of less interrupts, this also
allows the kernel to better utilize TSO. Since TSO has some CPU overhead,
it might not aggregate when CPU is under high stress. By reducing the
interrupt rate and the CPU utilization, we can get better aggregation
and better overall throughput.
The feature is enabled by default and has a private flag in ethtool
for control.
Throughput, interrupt rate and TSO utilization improvements:
(ConnectX-4Lx 40GbE, unidirectional, 1/16 TCP streams, 64B packets)
---------------------------------------------------------
Metric | Streams | CQE Based | EQE Based | improvement
---------------------------------------------------------
BW | 1 | 2.4Gb/s | 2.15Gb/s | +11.6%
IR | 1 | 27Kips | 50.6Kips | -46.7%
TSO Util | 1 | 74.6% | 71% | +5%
BW | 16 | 29Gb/s | 25.85Gb/s | +12.2%
IR | 16 | 482Kips | 745Kips | -35.3%
TSO Util | 16 | 69.1% | 49% | +41.1%
*BW = Bandwidth, IR = Interrupt rate, ips = interrupt per second.
TSO Util = bytes in TSO sessions / all bytes transferred
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
For supported platforms, add inner TTC flow table to enhanced IPoIB
flow steering.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This is needed in order to enlarge it with more members that will get
value of 0 when not set.
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The NIC TC offload table size was hard coded to 1k. Change it to be
min(max NIC RX table size,
min(max flow counters, 64k) * num flow groups)
where the max values are read from the firmware and the number of
flow groups is hard-coded as before this change.
We don't know upfront the division of flows to groups (== different masks).
This setup allows each group to be of size up to the where we want to go
(when supported, all offloaded flows use counters). Thus, we don't expect
multiple occurences for a group which in turn would add steering hops.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add debug print when changing the configuration of QoS through dcbnl.
Use ethtool -s <devname> msglvl hw on/off to toggle debug messages.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Reviewed-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use ethtool -s <devname> msglvl <type> on/off to toggle debug messages.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
If the port is in DSCP trust state, packets are placed in the right
priority queue based on the dscp value. This is done by selecting
the transmit queue based on the dscp of the skb.
Until now select_queue honors priority only from the vlan header.
However that is not sufficient in cases where port trust state is DSCP
mode as packet might not even contain vlan header. Therefore if the port
is in dscp trust state and vport's min inline mode is not NONE,
copy the IP header to the eseg's inline header if the skb has it.
This is done by changing the transmit queue sq's min inline mode to L3.
Note that the min inline mode of sqs that belong to other features such
as xdpsq, icosq are not modified.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This patch implements dcbnl hooks to set and delete DSCP to priority map
as defined by the DCB subsystem. Device maintains internal trust state
which needs to be set to DSCP state for performing DSCP to priority mapping.
When the first dscp to priority APP entry is added by the user, the
trust state is changed to dscp.
When the last dscp to priority APP entry is deleted by the user, the
trust state is changed to pcp.
If user sends multiple dscp to priority APP entries on the same dscp,
the last sent one will take effect. All the previous sent will be
deleted.
The dscp to priority APP entries are added and deleted in the net/dcb
APP database using dcb_ieee_setapp/getapp.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The QPTS register allows changing the priority trust state between pcp and
dscp. Add support to get/set trust state from device. When the port is
in pcp/dscp trust state, packet is routed by hardware to matching priority
based on its pcp/dscp value respectively.
The QPDPM register allow channing the dscp to priority mapping. Add support
to get/set dscp to priority mapping from device.
Note that to change a dscp mapping, the "e" bit of this dscp structure
must be set in the QPDPM firmware command.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The QCAM register provides capability bit for all the QoS registers
using ACCESS_REG command.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fixes the following sparse warnings:
drivers/net/phy/phylink.c:570:6: warning:
symbol 'phylink_phy_change' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.15
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return success if the same dispatch function is being registered for
a given opcode and subcode, there by allow multiple switchdev enable
and disables.
Signed-off-by: Vijaya Mohan Guvva <vijaya.guvva@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the bound device of a tunnel device is down, encapsulated packets
are not egressed anymore, but tunnel decap still works. Extend
mlxsw_sp_nexthop_rif_update() to take IFF_UP into consideration when
deciding whether a given next hop should be offloaded.
Because the new logic was added to mlxsw_sp_nexthop_rif_update(), this
fixes the case where a newly-added tunnel has a down bound device, which
would previously be fully offloaded. Now the down state of the bound
device is noted and next hops forwarding to such tunnel are not
offloaded.
In addition to that, notice NETDEV_UP and NETDEV_DOWN of a bound device
to force refresh of tunnel encap route offloads.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a bound device of an IP-in-IP tunnel changes, such as through
'ip tunnel change name $name dev $dev', the loopback backing the tunnel
needs to be recreated.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changes to L3 tunnel netdevices (through `ip tunnel change' as well as
`ip link set') lead to NETDEV_CHANGE being generated on the tunnel
device. Because what is relevant for the tunnel in question depends on
the tunnel type, handling of the event is dispatched to the IPIP module
through a newly-added interface mlxsw_sp_ipip_ops.ol_netdev_change().
IPIP tunnels now remember the last set of tunnel parameters in struct
mlxsw_sp_ipip_entry.parms, and use it to figure out what exactly has
changed.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a bound device of a tunnel netdevice changes VRF, the loopback RIF
that backs the tunnel needs to be updated and existing encapsulating
routes need to be refreshed.
Note that several tunnels can share the same bound device, in which case
all the impacted tunnels need to be updated.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The approach for offloading IP tunnels implemented currently by mlxsw
doesn't allow two tunnels that have the same local IP address in the
same (underlay) VRF. Previously, offloads were introduced on demand as
encap routes were formed. When such a route was created that would cause
offload of a conflicting tunnel, mlxsw_sp_ipip_entry_create() would
detect it and return -EEXIST, which would propagate up and cause FIB
abort.
Now however IPIP entries are created as soon as an offloadable netdevice
is created, and the failure prevents creation of such device.
Furthermore, if the driver is installed at the point where such
conflicting tunnels exist, the failure actually prevents successful
modprobe.
Furthermore, follow-up patches implement handling of NETDEV_CHANGE due
to the local address change. However, NETDEV_CHANGE can't be vetoed. The
failure merely means that the offloads weren't updated, but the change
in Linux configuration is not rolled back. It is thus desirable to have
a robust way of handling these conflicts, which can later be reused for
handling NETDEV_CHANGE as well.
To fix this, when a conflicting tunnel is created, instead of failing,
simply pull the old tunnel to slow path and reject offloading the
new one.
Introduce two functions: mlxsw_sp_ipip_entry_demote_tunnel() and
mlxsw_sp_ipip_demote_tunnel_by_saddr() to handle this. Make them both
public, because they will be useful later on in this patchset.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When trying to determine whether there are other offloaded tunnels with
the same local address, mlxsw_sp_ipip_entry_create() should look for a
tunnel with matching UL protocol, matching saddr, in the same VRF.
However instead of taking into account the UL protocol of the tunnel
netdevice (which mlxsw_sp_ipip_entry_saddr_matches() then compares to
the UL protocol of inspected IPIP entry), it deduces the UL protocol
from the inspected IPIP entry (and that's compared to itself).
This is currently immaterial, because only one tunnel type is offloaded,
and therefore the UL protocol always matches, but introducing support
for a tunnel with IPv6 underlay would uncover this error.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The work that needs to be done to update HW configuration in response to
changes is similar to what __mlxsw_sp_ipip_entry_update_tunnel() already
does, but with a number of twists: each change requires a different
subset of things to happen. Extend the function to support all these
uses, and allow finely-grained configuration of what should happen at
each call through a suite of function arguments.
Publish the updated function to allow use from the spectrum_ipip module.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The work that's done by mlxsw_sp_netdevice_ipip_ol_vrf_event() is a good
basis for a more versatile function that would take care of all sorts of
tunnel updates requests: __mlxsw_sp_ipip_entry_update_tunnel(). Extract
that function. Factor out a helper mlxsw_sp_ipip_entry_ol_lb_update() as
well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function mlxsw_sp_rif_create() takes an extack parameter. So far,
for creation of loopback interfaces, NULL was passed. For some events
however the extack can be extracted and passed along. So do that for
NETDEV_CHANGEUPPER handler.
Use the opportunity to update the type of info argument that
mlxsw_sp_netdevice_ipip_ol_event() takes. Follow-up patches will
introduce handling of more changes, and some of them carry an extack as
well, but in an info structure of a different type. Though not strictly
erroneous (the pointer could be cast whichever way), it makes no sense
to pretend the value is always of a certain type, when in fact it isn't.
So change the prototype of the above-mentioned function as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The piece of logic to promote decap route, if any, is useful for generic
tunnel updates, not just for handling of NETDEV_UP events on tunnel
interfaces. Extract it to a separate function.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function only ever returns 0, so don't pretend it returns anything
useful and just make it void.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To implement NETDEV_CHANGE notifications on IP-in-IP tunnels, the
handler needs to figure out what actually changed, to understand how
exactly to update the offloads. It will do so by storing struct
ip_tunnel_parm with previous configuration, and comparing that to the
new version.
To facilitate these comparisons, extract the code that operates on
struct ip_tunnel_parm from the existing accessor functions, and make
those a thin wrapper that extracts tunnel parameters and dispatches.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
