| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
With one of the on-board ASM1061 AHCI controllers (1b21:0612) on an
ASUSTeK Pro WS WRX80E-SAGE SE WIFI mainboard, a controller hang was
observed that was immediately preceded by the following kernel
messages:
ahci 0000:28:00.0: Using 64-bit DMA addresses
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00000 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00300 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00380 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00400 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00680 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00700 flags=0x0000]
The first message is produced by code in drivers/iommu/dma-iommu.c
which is accompanied by the following comment that seems to apply:
/*
* Try to use all the 32-bit PCI addresses first. The original SAC vs.
* DAC reasoning loses relevance with PCIe, but enough hardware and
* firmware bugs are still lurking out there that it's safest not to
* venture into the 64-bit space until necessary.
*
* If your device goes wrong after seeing the notice then likely either
* its driver is not setting DMA masks accurately, the hardware has
* some inherent bug in handling >32-bit addresses, or not all the
* expected address bits are wired up between the device and the IOMMU.
*/
Asking the ASM1061 on a discrete PCIe card to DMA from I/O virtual
address 0xffffffff00000000 produces the following I/O page faults:
vfio-pci 0000:07:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0x7ff00000000 flags=0x0010]
vfio-pci 0000:07:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0x7ff00000500 flags=0x0010]
Note that the upper 21 bits of the logged DMA address are zero. (When
asking a different PCIe device in the same PCIe slot to DMA to the
same I/O virtual address, we do see all the upper 32 bits of the DMA
address as 1, so this is not an issue with the chipset or IOMMU
configuration on the test system.)
Also, hacking libahci to always set the upper 21 bits of all DMA
addresses to 1 produces no discernible effect on the behavior of the
ASM1061, and mkfs/mount/scrub/etc work as without this hack.
This all strongly suggests that the ASM1061 has a 43 bit DMA address
limit, and this commit therefore adds a quirk to deal with this limit.
This issue probably applies to (some of) the other supported ASMedia
parts as well, but we limit it to the PCI IDs known to refer to
ASM1061 parts, as that's the only part we know for sure to be affected
by this issue at this point.
Link: https://lore.kernel.org/linux-ide/ZaZ2PIpEId-rl6jv@wantstofly.org/
Signed-off-by: Lennert Buytenhek <kernel@wantstofly.org>
[cassel: drop date from error messages in commit log]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
The fill ring of the XDP socket may contain not enough buffers to
completey fill the RX queue during socket creation. In this case the
flag XDP_RING_NEED_WAKEUP is not set as this flag is only set if the RX
queue is not completely filled during polling.
Set XDP_RING_NEED_WAKEUP flag also if RX queue is not completely filled
during XDP socket creation.
Fixes: 3fc2333933fd ("tsnep: Add XDP socket zero-copy RX support")
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The RX data buffer includes the FCS. The FCS is already stripped for the
normal data path. But for the XDP data path the FCS is included and
acts like additional/useless data.
Remove the FCS from the RX data buffer also for XDP.
Fixes: 65b28c810035 ("tsnep: Add XDP RX support")
Fixes: 3fc2333933fd ("tsnep: Add XDP socket zero-copy RX support")
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2024-01-24
This series provides bug fixes to mlx5 driver.
Please pull and let me know if there is any problem.
* tag 'mlx5-fixes-2024-01-24' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: fix a potential double-free in fs_any_create_groups
net/mlx5e: fix a double-free in arfs_create_groups
net/mlx5e: Ignore IPsec replay window values on sender side
net/mlx5e: Allow software parsing when IPsec crypto is enabled
net/mlx5: Use mlx5 device constant for selecting CQ period mode for ASO
net/mlx5: DR, Can't go to uplink vport on RX rule
net/mlx5: DR, Use the right GVMI number for drop action
net/mlx5: Bridge, fix multicast packets sent to uplink
net/mlx5: Fix a WARN upon a callback command failure
net/mlx5e: Fix peer flow lists handling
net/mlx5e: Fix inconsistent hairpin RQT sizes
net/mlx5e: Fix operation precedence bug in port timestamping napi_poll context
net/mlx5: Fix query of sd_group field
net/mlx5e: Use the correct lag ports number when creating TISes
====================
Link: https://lore.kernel.org/r/20240124081855.115410-1-saeed@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2024-01-25
The following pull-request contains BPF updates for your *net* tree.
We've added 12 non-merge commits during the last 2 day(s) which contain
a total of 13 files changed, 190 insertions(+), 91 deletions(-).
The main changes are:
1) Fix bpf_xdp_adjust_tail() in context of XSK zero-copy drivers which
support XDP multi-buffer. The former triggered a NULL pointer
dereference upon shrinking, from Maciej Fijalkowski & Tirthendu Sarkar.
2) Fix a bug in riscv64 BPF JIT which emitted a wrong prologue and
epilogue for struct_ops programs, from Pu Lehui.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
i40e: update xdp_rxq_info::frag_size for ZC enabled Rx queue
i40e: set xdp_rxq_info::frag_size
xdp: reflect tail increase for MEM_TYPE_XSK_BUFF_POOL
ice: update xdp_rxq_info::frag_size for ZC enabled Rx queue
intel: xsk: initialize skb_frag_t::bv_offset in ZC drivers
ice: remove redundant xdp_rxq_info registration
i40e: handle multi-buffer packets that are shrunk by xdp prog
ice: work on pre-XDP prog frag count
xsk: fix usage of multi-buffer BPF helpers for ZC XDP
xsk: make xsk_buff_pool responsible for clearing xdp_buff::flags
xsk: recycle buffer in case Rx queue was full
riscv, bpf: Fix unpredictable kernel crash about RV64 struct_ops
====================
Link: https://lore.kernel.org/r/20240125084416.10876-1-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When repeatedly changing the interface link speed using the command below:
ethtool -s eth0 speed 100 duplex full
ethtool -s eth0 speed 1000 duplex full
The following errors may sometimes be reported by the ARM SMMU driver:
[ 5395.035364] fec 5b040000.ethernet eth0: Link is Down
[ 5395.039255] arm-smmu 51400000.iommu: Unhandled context fault:
fsr=0x402, iova=0x00000000, fsynr=0x100001, cbfrsynra=0x852, cb=2
[ 5398.108460] fec 5b040000.ethernet eth0: Link is Up - 100Mbps/Full -
flow control off
It is identified that the FEC driver does not properly stop the TX queue
during the link speed transitions, and this results in the invalid virtual
I/O address translations from the SMMU and causes the context faults.
Fixes: dbc64a8ea231 ("net: fec: move calls to quiesce/resume packet processing out of fec_restart()")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20240123165141.2008104-1-shenwei.wang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
- Synchronize job submission with reset/recovery using reset_lock
- Always print recovery reason and call diagnose_failure()
- Don't allow for autosupend during recovery
- Prevent immediate autosuspend after reset/recovery
- Prevent force_recovery for issuing TDR when device is suspended
- Reset VPU instead triggering recovery after changing debugfs params
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Wachowski, Karol <karol.wachowski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240122120945.1150728-4-jacek.lawrynowicz@linux.intel.com
|
|
- Wake up the device as late as possible
- Remove job reference counting in order to simplify the code
- Don't put jobs that are not fully submitted on submitted_jobs_xa in
order to avoid potential races with reset/recovery
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Wachowski, Karol <karol.wachowski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240122120945.1150728-3-jacek.lawrynowicz@linux.intel.com
|
|
- Add context_list_lock to synchronize user context addition/removal
- Use drm_dev_enter() to prevent unbinding the device during ivpu_open()
and vpu address allocation
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Wachowski, Karol <karol.wachowski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240122120945.1150728-2-jacek.lawrynowicz@linux.intel.com
|
|
On HSW non-ULT (or at least on Dell Latitude E6540) external displays
start to flicker when we enable PSR on the eDP. We observe a much higher
SR and PC6 residency than should be possible with an external display,
and indeen much higher than what we observe with eDP disabled and
only the external display enabled. Looks like the hardware is somehow
ignoring the fact that the external display is active during PSR.
I wasn't able to redproduce this on my HSW ULT machine, or BDW.
So either there's something specific about this particular laptop
(eg. some unknown firmware thing) or the issue is limited to just
non-ULT HSW systems. All known registers that could affect this
look perfectly reasonable on the affected machine.
As a workaround let's unmask the LPSP event to prevent PSR entry
except while in LPSP mode (only pipe A + eDP active). This
will prevent PSR entry entirely when multiple pipes are active.
The one slight downside is that we now also prevent PSR entry
when driving eDP with pipe B or C, but I think that's a reasonable
tradeoff to avoid having to implement a more complex workaround.
Cc: stable@vger.kernel.org
Fixes: 783d8b80871f ("drm/i915/psr: Re-enable PSR1 on hsw/bdw")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10092
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240118212131.31868-1-ville.syrjala@linux.intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
(cherry picked from commit 94501c3ca6400e463ff6cc0c9cf4a2feb6a9205d)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
RCU protection was removed in the commit 2d32777d60de ("raid1: remove rcu
protection to access rdev from conf").
However, the code in fix_read_error does rcu_dereference outside
rcu_read_lock - this triggers the following warning. The warning is
triggered by a LVM2 test shell/integrity-caching.sh.
This commit removes rcu_dereference.
=============================
WARNING: suspicious RCU usage
6.7.0 #2 Not tainted
-----------------------------
drivers/md/raid1.c:2265 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
no locks held by mdX_raid1/1859.
stack backtrace:
CPU: 2 PID: 1859 Comm: mdX_raid1 Not tainted 6.7.0 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x60/0x70
lockdep_rcu_suspicious+0x153/0x1b0
raid1d+0x1732/0x1750 [raid1]
? lock_acquire+0x9f/0x270
? finish_wait+0x3d/0x80
? md_thread+0xf7/0x130 [md_mod]
? lock_release+0xaa/0x230
? md_register_thread+0xd0/0xd0 [md_mod]
md_thread+0xa0/0x130 [md_mod]
? housekeeping_test_cpu+0x30/0x30
kthread+0xdc/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x28/0x40
? kthread_complete_and_exit+0x20/0x20
ret_from_fork_asm+0x11/0x20
</TASK>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: ca294b34aaf3 ("md/raid1: support read error check")
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/51539879-e1ca-fde3-b8b4-8934ddedcbc@redhat.com
|
|
Creating a region with 16 memory devices caused a problem. The div_u64_rem
function, used for dividing an unsigned 64-bit number by a 32-bit one,
faced an issue when SZ_256M * p->interleave_ways. The result surpassed
the maximum limit of the 32-bit divisor (4G), leading to an overflow
and a remainder of 0.
note: At this point, p->interleave_ways is 16, meaning 16 * 256M = 4G
To fix this issue, I replaced the div_u64_rem function with div64_u64_rem
and adjusted the type of the remainder.
Signed-off-by: Quanquan Cao <caoqq@fujitsu.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 23a22cd1c98b ("cxl/region: Allocate HPA capacity to regions")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Several fixups
- Minor fix in `drm/exynos: gsc: gsc_runtime_resume`
. The patch ensures `clk_disable_unprepare()` is called on the first
element of `ctx->clocks` array.
This issue was identified by the Linux Verification Center.
- Fix excessive stack usage in `fimd_win_set_pixfmt()` in `drm/exynos`
. The issue, highlighted by gcc, involved an unnecessary on-stack copy of
the large `exynos_drm_plane` structure, now replaced with a pointer.
- Fix an incorrect type issue in `exynos_drm_fimd.c` module
. Addresses an incorrect type issue in `fimd_commit()` within the
`exynos_drm_fimd.c` The problem was reported by the kernel test robot[1].
[1] https://lore.kernel.org/oe-kbuild-all/202312140930.Me9yWf8F-lkp@intel.com/
- Fix a typo in the dt-bindings for `samsung,exynos-mixer`
. Changes 'regs' to the correct property name 'reg' in the dt-bindings
documentation for `samsung,exynos-mixer`
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240122072407.39546-1-inki.dae@samsung.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
A null pointer dereference fix for v3d and a protection fault fix for
ttm.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/5zrphn2nhxnwillxlmo6ap3zh7qjt3jgydlm5sntuc4fzvwhpo@hznprx2bjyi7
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- DSI sequence revert to fix GitLab #10071 and DP test-pattern fix
- Drop -Wstringop-overflow (broken on GCC11)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZaozNnAGhu6Ec6cb@jlahtine-mobl.ger.corp.intel.com
|
|
In fjes_hw_setup, it allocates several memory and delay the deallocation
to the fjes_hw_exit in fjes_probe through the following call chain:
fjes_probe
|-> fjes_hw_init
|-> fjes_hw_setup
|-> fjes_hw_exit
However, when fjes_hw_setup fails, fjes_hw_exit won't be called and thus
all the resources allocated in fjes_hw_setup will be leaked. In this
patch, we free those resources in fjes_hw_setup and prevents such leaks.
Fixes: 2fcbca687702 ("fjes: platform_driver's .probe and .remove routine")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240122172445.3841883-1-alexious@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull ceph fixes from Ilya Dryomov:
"A fix to avoid triggering an assert in some cases where RBD exclusive
mappings are involved and a deprecated API cleanup"
* tag 'ceph-for-6.8-rc2' of https://github.com/ceph/ceph-client:
rbd: don't move requests to the running list on errors
rbd: remove usage of the deprecated ida_simple_*() API
|
|
Now that i40e driver correctly sets up frag_size in xdp_rxq_info, let us
make it work for ZC multi-buffer as well. i40e_ring::rx_buf_len for ZC
is being set via xsk_pool_get_rx_frame_size() and this needs to be
propagated up to xdp_rxq_info.
Fixes: 1c9ba9c14658 ("i40e: xsk: add RX multi-buffer support")
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-12-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
i40e support XDP multi-buffer so it is supposed to use
__xdp_rxq_info_reg() instead of xdp_rxq_info_reg() and set the
frag_size. It can not be simply converted at existing callsite because
rx_buf_len could be un-initialized, so let us register xdp_rxq_info
within i40e_configure_rx_ring(), which happen to be called with already
initialized rx_buf_len value.
Commit 5180ff1364bc ("i40e: use int for i40e_status") converted 'err' to
int, so two variables to deal with return codes are not needed within
i40e_configure_rx_ring(). Remove 'ret' and use 'err' to handle status
from xdp_rxq_info registration.
Fixes: e213ced19bef ("i40e: add support for XDP multi-buffer Rx")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-11-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Now that ice driver correctly sets up frag_size in xdp_rxq_info, let us
make it work for ZC multi-buffer as well. ice_rx_ring::rx_buf_len for ZC
is being set via xsk_pool_get_rx_frame_size() and this needs to be
propagated up to xdp_rxq_info.
Use a bigger hammer and instead of unregistering only xdp_rxq_info's
memory model, unregister it altogether and register it again and have
xdp_rxq_info with correct frag_size value.
Fixes: 1bbc04de607b ("ice: xsk: add RX multi-buffer support")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-9-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Ice and i40e ZC drivers currently set offset of a frag within
skb_shared_info to 0, which is incorrect. xdp_buffs that come from
xsk_buff_pool always have 256 bytes of a headroom, so they need to be
taken into account to retrieve xdp_buff::data via skb_frag_address().
Otherwise, bpf_xdp_frags_increase_tail() would be starting its job from
xdp_buff::data_hard_start which would result in overwriting existing
payload.
Fixes: 1c9ba9c14658 ("i40e: xsk: add RX multi-buffer support")
Fixes: 1bbc04de607b ("ice: xsk: add RX multi-buffer support")
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-8-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
xdp_rxq_info struct can be registered by drivers via two functions -
xdp_rxq_info_reg() and __xdp_rxq_info_reg(). The latter one allows
drivers that support XDP multi-buffer to set up xdp_rxq_info::frag_size
which in turn will make it possible to grow the packet via
bpf_xdp_adjust_tail() BPF helper.
Currently, ice registers xdp_rxq_info in two spots:
1) ice_setup_rx_ring() // via xdp_rxq_info_reg(), BUG
2) ice_vsi_cfg_rxq() // via __xdp_rxq_info_reg(), OK
Cited commit under fixes tag took care of setting up frag_size and
updated registration scheme in 2) but it did not help as
1) is called before 2) and as shown above it uses old registration
function. This means that 2) sees that xdp_rxq_info is already
registered and never calls __xdp_rxq_info_reg() which leaves us with
xdp_rxq_info::frag_size being set to 0.
To fix this misbehavior, simply remove xdp_rxq_info_reg() call from
ice_setup_rx_ring().
Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side")
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-7-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
XDP programs can shrink packets by calling the bpf_xdp_adjust_tail()
helper function. For multi-buffer packets this may lead to reduction of
frag count stored in skb_shared_info area of the xdp_buff struct. This
results in issues with the current handling of XDP_PASS and XDP_DROP
cases.
For XDP_PASS, currently skb is being built using frag count of
xdp_buffer before it was processed by XDP prog and thus will result in
an inconsistent skb when frag count gets reduced by XDP prog. To fix
this, get correct frag count while building the skb instead of using
pre-obtained frag count.
For XDP_DROP, current page recycling logic will not reuse the page but
instead will adjust the pagecnt_bias so that the page can be freed. This
again results in inconsistent behavior as the page refcnt has already
been changed by the helper while freeing the frag(s) as part of
shrinking the packet. To fix this, only adjust pagecnt_bias for buffers
that are stillpart of the packet post-xdp prog run.
Fixes: e213ced19bef ("i40e: add support for XDP multi-buffer Rx")
Reported-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tirthendu Sarkar <tirthendu.sarkar@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-6-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Fix an OOM panic in XDP_DRV mode when a XDP program shrinks a
multi-buffer packet by 4k bytes and then redirects it to an AF_XDP
socket.
Since support for handling multi-buffer frames was added to XDP, usage
of bpf_xdp_adjust_tail() helper within XDP program can free the page
that given fragment occupies and in turn decrease the fragment count
within skb_shared_info that is embedded in xdp_buff struct. In current
ice driver codebase, it can become problematic when page recycling logic
decides not to reuse the page. In such case, __page_frag_cache_drain()
is used with ice_rx_buf::pagecnt_bias that was not adjusted after
refcount of page was changed by XDP prog which in turn does not drain
the refcount to 0 and page is never freed.
To address this, let us store the count of frags before the XDP program
was executed on Rx ring struct. This will be used to compare with
current frag count from skb_shared_info embedded in xdp_buff. A smaller
value in the latter indicates that XDP prog freed frag(s). Then, for
given delta decrement pagecnt_bias for XDP_DROP verdict.
While at it, let us also handle the EOP frag within
ice_set_rx_bufs_act() to make our life easier, so all of the adjustments
needed to be applied against freed frags are performed in the single
place.
Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side")
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-5-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
XDP multi-buffer support introduced XDP_FLAGS_HAS_FRAGS flag that is
used by drivers to notify data path whether xdp_buff contains fragments
or not. Data path looks up mentioned flag on first buffer that occupies
the linear part of xdp_buff, so drivers only modify it there. This is
sufficient for SKB and XDP_DRV modes as usually xdp_buff is allocated on
stack or it resides within struct representing driver's queue and
fragments are carried via skb_frag_t structs. IOW, we are dealing with
only one xdp_buff.
ZC mode though relies on list of xdp_buff structs that is carried via
xsk_buff_pool::xskb_list, so ZC data path has to make sure that
fragments do *not* have XDP_FLAGS_HAS_FRAGS set. Otherwise,
xsk_buff_free() could misbehave if it would be executed against xdp_buff
that carries a frag with XDP_FLAGS_HAS_FRAGS flag set. Such scenario can
take place when within supplied XDP program bpf_xdp_adjust_tail() is
used with negative offset that would in turn release the tail fragment
from multi-buffer frame.
Calling xsk_buff_free() on tail fragment with XDP_FLAGS_HAS_FRAGS would
result in releasing all the nodes from xskb_list that were produced by
driver before XDP program execution, which is not what is intended -
only tail fragment should be deleted from xskb_list and then it should
be put onto xsk_buff_pool::free_list. Such multi-buffer frame will never
make it up to user space, so from AF_XDP application POV there would be
no traffic running, however due to free_list getting constantly new
nodes, driver will be able to feed HW Rx queue with recycled buffers.
Bottom line is that instead of traffic being redirected to user space,
it would be continuously dropped.
To fix this, let us clear the mentioned flag on xsk_buff_pool side
during xdp_buff initialization, which is what should have been done
right from the start of XSK multi-buffer support.
Fixes: 1bbc04de607b ("ice: xsk: add RX multi-buffer support")
Fixes: 1c9ba9c14658 ("i40e: xsk: add RX multi-buffer support")
Fixes: 24ea50127ecf ("xsk: support mbuf on ZC RX")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-3-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Marvel RVU mbox driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240123190332.677489-11-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the LiteX Liteeth Ethernet device.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20240123190332.677489-10-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Freescale PQ MDIO driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240123190332.677489-9-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the FEC (MPC8xx) Ethernet controller.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20240123190332.677489-8-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the NXP ENETC Ethernet driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240123190332.677489-7-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the EZchip NPS ethernet driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240123190332.677489-6-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Cirrus EP93xx ethernet driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240123190332.677489-5-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Cavium Liquidio.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240123190332.677489-4-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Broadcom iProc GBit driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240123190332.677489-3-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to all the good old 8390 modules and drivers.
Signed-off-by: Breno Leitao <leitao@debian.org>
CC: geert@linux-m68k.org
Link: https://lore.kernel.org/r/20240123190332.677489-2-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Register value persist after booting the kernel using
kexec which results in kernel panic. Thus clear the
BM pool registers before initialisation to fix the issue.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Jenishkumar Maheshbhai Patel <jpatel2@marvell.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://lore.kernel.org/r/20240119035914.2595665-1-jpatel2@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
otherwise the synopsys_id value may be read out wrong,
because the GMAC_VERSION register might still be in reset
state, for at least 1 us after the reset is de-asserted.
Add a wait for 10 us before continuing to be on the safe side.
> From what have you got that delay value?
Just try and error, with very old linux versions and old gcc versions
the synopsys_id was read out correctly most of the time (but not always),
with recent linux versions and recnet gcc versions it was read out
wrongly most of the time, but again not always.
I don't have access to the VHDL code in question, so I cannot
tell why it takes so long to get the correct values, I also do not
have more than a few hardware samples, so I cannot tell how long
this timeout must be in worst case.
Experimentally I can tell that the register is read several times
as zero immediately after the reset is de-asserted, also adding several
no-ops is not enough, adding a printk is enough, also udelay(1) seems to
be enough but I tried that not very often, and I have not access to many
hardware samples to be 100% sure about the necessary delay.
And since the udelay here is only executed once per device instance,
it seems acceptable to delay the boot for 10 us.
BTW: my hardware's synopsys id is 0x37.
Fixes: c5e4ddbdfa11 ("net: stmmac: Add support for optional reset control")
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/AS8P193MB1285A810BD78C111E7F6AA34E4752@AS8P193MB1285.EURP193.PROD.OUTLOOK.COM
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As it devm_pm_runtime_enable can fail due to memory allocations, it is
best to handle the error.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://msgid.link/r/20240124174101.2270249-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fixes and cleanups from Helge Deller:
"A crash fix in stifb which was missed to be included in the drm-misc
tree, two checks to prevent wrong userspace input in sisfb and
savagefb and two trivial printk cleanups:
- stifb: Fix crash in stifb_blank()
- savage/sis: Error out if pixclock equals zero
- minor trivial cleanups"
* tag 'fbdev-for-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: stifb: Fix crash in stifb_blank()
fbcon: Fix incorrect printed function name in fbcon_prepare_logo()
fbdev: sis: Error out if pixclock equals zero
fbdev: savage: Error out if pixclock equals zero
fbdev: vt8500lcdfb: Remove unnecessary print function dev_err()
|
|
Several functions implementing VIDIOC_REQBUFS and _CREATE_BUFS all use
almost the same code to fill in the flags and capability fields. Refactor
this into a new vb2_set_flags_and_caps() function that replaces the old
fill_buf_caps() and validate_memory_flags() functions.
This also fixes a bug where vb2_ioctl_create_bufs() would not set the
V4L2_BUF_CAP_SUPPORTS_MAX_NUM_BUFFERS cap and also not fill in the
max_num_buffers field.
Fixes: d055a76c0065 ("media: core: Report the maximum possible number of buffers for the queue")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Acked-by: Tomasz Figa <tfiga@chromium.org>
|
|
Use vb2_get_num_buffers() to avoid using queue num_buffers field directly.
This allows us to change how the number of buffers is computed in the
future.
Fixes: d055a76c0065 ("media: core: Report the maximum possible number of buffers for the queue")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Change compatible string to match dt bindings for TI devices. K3 family
prefix should not be included as it deviates from naming convention.
Fixes: 9707a6254a8a ("media: chips-media: wave5: Add the v4l2 layer")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/all/CAMuHMdUYOq=q1j=d+Eac28hthOUAaNUkuvxmRu-mUN1pLKq69g@mail.gmail.com/
Signed-off-by: Brandon Brnich <b-brnich@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
subsys_initcall_sync"
This reverts commit 60aebc9559492cea6a9625f514a8041717e3a2e4.
Commit 60aebc9559492cea ("drivers/firmware: Move sysfb_init() from
device_initcall to subsys_initcall_sync") messes up initialization order
of the graphics drivers and leads to blank displays on some systems. So
revert the commit.
To make the display drivers fully independent from initialization
order requires to track framebuffer memory by device and independently
from the loaded drivers. The kernel currently lacks the infrastructure
to do so.
Reported-by: Jaak Ristioja <jaak@ristioja.ee>
Closes: https://lore.kernel.org/dri-devel/ZUnNi3q3yB3zZfTl@P70.localdomain/T/#t
Reported-by: Huacai Chen <chenhuacai@loongson.cn>
Closes: https://lore.kernel.org/dri-devel/20231108024613.2898921-1-chenhuacai@loongson.cn/
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10133
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: stable@vger.kernel.org # v6.5+
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240123120937.27736-1-tzimmermann@suse.de
|
|
Move set_capacity() outside of the section procected by (&d->lock).
To avoid possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
[1] lock(&bdev->bd_size_lock);
local_irq_disable();
[2] lock(&d->lock);
[3] lock(&bdev->bd_size_lock);
<Interrupt>
[4] lock(&d->lock);
*** DEADLOCK ***
Where [1](&bdev->bd_size_lock) hold by zram_add()->set_capacity().
[2]lock(&d->lock) hold by aoeblk_gdalloc(). And aoeblk_gdalloc()
is trying to acquire [3](&bdev->bd_size_lock) at set_capacity() call.
In this situation an attempt to acquire [4]lock(&d->lock) from
aoecmd_cfg_rsp() will lead to deadlock.
So the simplest solution is breaking lock dependency
[2](&d->lock) -> [3](&bdev->bd_size_lock) by moving set_capacity()
outside.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240124072436.3745720-2-bigunclemax@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Since the PCI IDs for PVC weren't added to the xe driver, the xe_wa
tests should not try to create a fake PVC device since they can't find
the right PCI ID. Fix bugs when running kunit:
# xe_wa_gt: ASSERTION FAILED at drivers/gpu/drm/xe/tests/xe_wa_test.c:111
Expected ret == 0, but
ret == -19 (0xffffffffffffffed)
[FAILED] PVC (B0)
# xe_wa_gt: ASSERTION FAILED at drivers/gpu/drm/xe/tests/xe_wa_test.c:111
Expected ret == 0, but
ret == -19 (0xffffffffffffffed)
[FAILED] PVC (B1)
# xe_wa_gt: ASSERTION FAILED at drivers/gpu/drm/xe/tests/xe_wa_test.c:111
Expected ret == 0, but
ret == -19 (0xffffffffffffffed)
[FAILED] PVC (C0)
Fixes: dd08ebf6c352 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240123031242.3548724-1-lucas.demarchi@intel.com
(cherry picked from commit ab5ae65fb25d06c38a6617a628b964828adb4786)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
Fix xe_vm_create_ioctl routine not freeing the vm-id allocated to it
when the function fails.
Fixes: dd08ebf6c352 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240122102424.4008095-1-mhaimovski@habana.ai
(cherry picked from commit f6bf0424cadc27d7cf6a049d2db960e4b52fa513)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
The pat table entry associated with XE_CACHE_WB is coherent whereas
XE_CACHE_NONE is non coherent. Migration expects the coherency
with cpu therefore use the coherent entry XE_CACHE_WB for
buffers not supporting compression. For read/write to flat ccs region
the issue is not related to coherency with cpu. The hardware expects
the pat index associated with GPUVA for indirect access to be
compression enabled hence use XE_CACHE_NONE_COMPRESSION.
v2
- Fix the argument to emit_pte, pass the bool directly. (Thomas)
v3
- Rebase
- Update commit message (Matt)
v4
- Add a Fixes: tag. (Thomas)
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Fixes: 65ef8dbad1db ("drm/xe/xe2: Update emit_pte to use compression enabled PAT index")
Signed-off-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240119041826.1670496-1-himal.prasad.ghimiray@intel.com
(cherry picked from commit 6a02867560f77328ae5637b70b06704b140aafa6)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
readq() is not available in 32bits and i915_gem_object_read_from_page()
is supposed to allow reading arbitrary sizes determined by the `size`
argument. Currently the only caller only passes a size == 8 so the
second problem is not that big. Migrate to calling
memcpy()/memcpy_fromio() to allow possible changes in the display side
and to fix the build on 32b architectures.
v2: Use memcpy/memcpy_fromio directly rather than using iosys-map with
the same size == 8 bytes restriction (Matt Roper)
Fixes: 44e694958b95 ("drm/xe/display: Implement display support")
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240119001612.2991381-4-lucas.demarchi@intel.com
(cherry picked from commit 406663f777bee53e9ad93dc080c333d4655ab7de)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
resource_size_t uses %pa format in printk since the size varies
depending on build options. However to keep the io_size/physical_size
addition in the same call we can't pass the address without adding yet
another variable in these function. Simply cast it to u64 and keep using
%llx.
Fixes: 286089ce6929 ("drm/xe: Improve vram info debug printing")
Cc: Oak Zeng <oak.zeng@intel.com>
Cc: Michael J. Ruhl <michael.j.ruhl@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240119001612.2991381-3-lucas.demarchi@intel.com
(cherry picked from commit 6d8d038364d8ec573e9dc0872e17bee1e5f12490)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
Use DIV_ROUND_UP_ULL() so it also works on 32bit build.
Fixes: dd08ebf6c352 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240119001612.2991381-2-lucas.demarchi@intel.com
(cherry picked from commit 7b5bdb447b14930b9ef3e39bd301937889c60c96)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
