Age | Commit message (Collapse) | Author | Files | Lines |
|
Fixes OOPS on boards with ANX9805 DP encoders.
Cc: stable@vger.kernel.org # 6.4+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230719044051.6975-3-skeggsb@gmail.com
|
|
Fixes crash on boards with ANX9805 TMDS/DP encoders.
Cc: stable@vger.kernel.org # 6.4+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230719044051.6975-2-skeggsb@gmail.com
|
|
This was completely bogus before, using maximum DCB device index rather
than maximum AUX ID to size the buffer that stores event refcounts.
*Pretty* unlikely to have been an actual problem on most configurations,
that is, unless you've got one of the rare boards that have off-chip DP.
There, it'll likely crash.
Cc: stable@vger.kernel.org # 6.4+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230719044051.6975-1-skeggsb@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-07-17 (iavf)
This series contains updates to iavf driver only.
Ding Hui fixes use-after-free issue by calling netif_napi_del() for all
allocated q_vectors. He also resolves out-of-bounds issue by not
updating to new values when timeout is encountered.
Marcin and Ahmed change the way resets are handled so that the callback
operating under the RTNL lock will wait for the reset to finish, the
rtnl_lock sensitive functions in reset flow will schedule the netdev update
for later in order to remove circular dependency with the critical lock.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
iavf: fix reset task race with iavf_remove()
iavf: fix a deadlock caused by rtnl and driver's lock circular dependencies
Revert "iavf: Do not restart Tx queues after reset task failure"
Revert "iavf: Detach device during reset task"
iavf: Wait for reset in callbacks which trigger it
iavf: use internal state to free traffic IRQs
iavf: Fix out-of-bounds when setting channels on remove
iavf: Fix use-after-free in free_netdev
====================
Link: https://lore.kernel.org/r/20230717175205.3217774-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Hardware generated encryption and ICV tags are found to
be wrong when tested with IEEE MACSEC test vectors.
This is because as per the HRM, the hash key (derived by
AES-ECB block encryption of an all 0s block with the SAK)
has to be programmed by the software in
MCSX_RS_MCS_CPM_TX_SLAVE_SA_PLCY_MEM_4X register.
Hence fix this by generating hash key in software and
configuring in hardware.
Fixes: c54ffc73601c ("octeontx2-pf: mcs: Introduce MACSEC hardware offloading")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://lore.kernel.org/r/1689574603-28093-1-git-send-email-sbhatta@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In normal operation, each populated queue item has
next_to_watch pointing to the last TX desc of the packet,
while each cleaned item has it set to 0. In particular,
next_to_use that points to the next (necessarily clean)
item to use has next_to_watch set to 0.
When the TX queue is used both by an application using
AF_XDP with ZEROCOPY as well as a second non-XDP application
generating high traffic, the queue pointers can get in
an invalid state where next_to_use points to an item
where next_to_watch is NOT set to 0.
However, the implementation assumes at several places
that this is never the case, so if it does hold,
bad things happen. In particular, within the loop inside
of igc_clean_tx_irq(), next_to_clean can overtake next_to_use.
Finally, this prevents any further transmission via
this queue and it never gets unblocked or signaled.
Secondly, if the queue is in this garbled state,
the inner loop of igc_clean_tx_ring() will never terminate,
completely hogging a CPU core.
The reason is that igc_xdp_xmit_zc() reads next_to_use
before acquiring the lock, and writing it back
(potentially unmodified) later. If it got modified
before locking, the outdated next_to_use is written
pointing to an item that was already used elsewhere
(and thus next_to_watch got written).
Fixes: 9acf59a752d4 ("igc: Enable TX via AF_XDP zero-copy")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230717175444.3217831-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2023-07-17
The 1st patch is by Ziyang Xuan and fixes a possible memory leak in
the receiver handling in the CAN RAW protocol.
YueHaibing contributes a use after free in bcm_proc_show() of the
Broad Cast Manager (BCM) CAN protocol.
The next 2 patches are by me and fix a possible null pointer
dereference in the RX path of the gs_usb driver with activated
hardware timestamps and the candlelight firmware.
The last patch is by Fedor Ross, Marek Vasut and me and targets the
mcp251xfd driver. The polling timeout of __mcp251xfd_chip_set_mode()
is increased to fix bus joining on busy CAN buses and very low bit
rate.
* tag 'linux-can-fixes-for-6.5-20230717' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: mcp251xfd: __mcp251xfd_chip_set_mode(): increase poll timeout
can: gs_usb: fix time stamp counter initialization
can: gs_usb: gs_can_open(): improve error handling
can: bcm: Fix UAF in bcm_proc_show()
can: raw: fix receiver memory leak
====================
Link: https://lore.kernel.org/r/20230717180938.230816-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
~0 as no xcp partition is used in several places, so improve its
definition by a macro for code consistency.
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Other PDs/PTs allocation should just use the same xcp_id as that
stored in root PD.
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Recent code set xcp_id stored from file private data when opening
device to amdgpu bo for accounting memory usage etc, but not all
VMs are attached to this fpriv structure like the vm cases in
amdgpu_mes_self_test, otherwise, KASAN will complain below out
of bound access. And more importantly, VM code should not touch
fpriv structure, so drop fpriv code handling from amdgpu_vm_pt.
[ 77.292314] BUG: KASAN: slab-out-of-bounds in amdgpu_vm_pt_create+0x17e/0x4b0 [amdgpu]
[ 77.293845] Read of size 4 at addr ffff888102c48a48 by task modprobe/1069
[ 77.294146] Call Trace:
[ 77.294178] <TASK>
[ 77.294208] dump_stack_lvl+0x49/0x63
[ 77.294260] print_report+0x16f/0x4a6
[ 77.294307] ? amdgpu_vm_pt_create+0x17e/0x4b0 [amdgpu]
[ 77.295979] ? kasan_complete_mode_report_info+0x3c/0x200
[ 77.296057] ? amdgpu_vm_pt_create+0x17e/0x4b0 [amdgpu]
[ 77.297556] kasan_report+0xb4/0x130
[ 77.297609] ? amdgpu_vm_pt_create+0x17e/0x4b0 [amdgpu]
[ 77.299202] __asan_load4+0x6f/0x90
[ 77.299272] amdgpu_vm_pt_create+0x17e/0x4b0 [amdgpu]
[ 77.300796] ? amdgpu_init+0x6e/0x1000 [amdgpu]
[ 77.302222] ? amdgpu_vm_pt_clear+0x750/0x750 [amdgpu]
[ 77.303721] ? preempt_count_sub+0x18/0xc0
[ 77.303786] amdgpu_vm_init+0x39e/0x870 [amdgpu]
[ 77.305186] ? amdgpu_vm_wait_idle+0x90/0x90 [amdgpu]
[ 77.306683] ? kasan_set_track+0x25/0x30
[ 77.306737] ? kasan_save_alloc_info+0x1b/0x30
[ 77.306795] ? __kasan_kmalloc+0x87/0xa0
[ 77.306852] amdgpu_mes_self_test+0x169/0x620 [amdgpu]
v2: without specifying xcp partition for PD/PT bo, the xcp id is -1.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2686
Fixes: 3ebfd221c1a8 ("drm/amdkfd: Store xcp partition id to amdgpu bo")
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
file_priv needs to be setup firstly, otherwise, root PD
will always be allocated on partition 0, even if opening
the device from other partitions.
Fixes: 3ebfd221c1a8 ("drm/amdkfd: Store xcp partition id to amdgpu bo")
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Port of a change that went into DCN314 to keep the PHY enabled
when we have a connected and active DP display.
The PHY can hang if PHY refclk is disabled inadvertently.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
In dcn314 DML the destination pipe vtotal was being set
to the crtc adjustment vtotal_min value even in cases
where that value is 0.
[How]
Only set vtotal to the crtc adjustment vtotal_min value
in cases where the value is non-zero.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
All of pipes will be used when the MPC split enable on the dcn
which just has 2 pipes. Then MPO enter will trigger the minimal
transition which need programe dcn from 2 pipes MPC split to 2
pipes MPO. This action will cause lag if happen frequently.
[HOW]
Disable the MPC split for the platform which dcn resource is limited
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Zhikai Zhai <zhikai.zhai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
If there is no TG allocation we can dereference a NULL pointer when
checking if the TG is enabled.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Specific TBT4 dock doesn't send out short HPD to notify source
that IRQ event DOWN_REP_MSG_RDY is set. Which violates the spec
and cause source can't send out streams to mst sinks.
[How]
To cover this misbehavior, add an additional polling method to detect
DOWN_REP_MSG_RDY is set. HPD driven handling method is still kept.
Just hook up our handler to drm mgr->cbs->poll_hpd_irq().
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fix the following errors & warnings reported by checkpatch:
ERROR: space required before the open brace '{'
ERROR: space required before the open parenthesis '('
ERROR: that open brace { should be on the previous line
ERROR: space prohibited before that ',' (ctx:WxW)
ERROR: else should follow close brace '}'
ERROR: open brace '{' following function definitions go on the next line
ERROR: code indent should use tabs where possible
WARNING: braces {} are not necessary for single statement blocks
WARNING: void function return statements are not generally useful
WARNING: Block comments use * on subsequent lines
WARNING: Block comments use a trailing */ on a separate line
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Allow the initramfs generator to automatically include psp_13_0_6_ta
firmware to initramfs.
Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Use current uclk to be consistent with other dGPUs.
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
|
|
Use average gfxclock for consistency with other dGPUs.
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
|
|
Up until now, amdgpu was silently degrading to vsync when
user-space requested an async flip but the hardware didn't support
it.
The hardware doesn't support immediate flips when the update changes
the FB pitch, the DCC state, the rotation, enables or disables CRTCs
or planes, etc. This is reflected in the dm_crtc_state.update_type
field: UPDATE_TYPE_FAST means that immediate flip is supported.
Silently degrading async flips to vsync is not the expected behavior
from a uAPI point-of-view. Xorg expects async flips to fail if
unsupported, to be able to fall back to a blit. i915 already behaves
this way.
This patch aligns amdgpu with uAPI expectations and returns a failure
when an async flip is not possible.
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: André Almeida <andrealmeid@igalia.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: André Almeida <andrealmeid@igalia.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
In below thousands of screen rotation loop tests with virtual display
enabled, a CPU hard lockup issue may happen, leading system to unresponsive
and crash.
do {
xrandr --output Virtual --rotate inverted
xrandr --output Virtual --rotate right
xrandr --output Virtual --rotate left
xrandr --output Virtual --rotate normal
} while (1);
NMI watchdog: Watchdog detected hard LOCKUP on cpu 1
? hrtimer_run_softirq+0x140/0x140
? store_vblank+0xe0/0xe0 [drm]
hrtimer_cancel+0x15/0x30
amdgpu_vkms_disable_vblank+0x15/0x30 [amdgpu]
drm_vblank_disable_and_save+0x185/0x1f0 [drm]
drm_crtc_vblank_off+0x159/0x4c0 [drm]
? record_print_text.cold+0x11/0x11
? wait_for_completion_timeout+0x232/0x280
? drm_crtc_wait_one_vblank+0x40/0x40 [drm]
? bit_wait_io_timeout+0xe0/0xe0
? wait_for_completion_interruptible+0x1d7/0x320
? mutex_unlock+0x81/0xd0
amdgpu_vkms_crtc_atomic_disable
It's caused by a stuck in lock dependency in such scenario on different
CPUs.
CPU1 CPU2
drm_crtc_vblank_off hrtimer_interrupt
grab event_lock (irq disabled) __hrtimer_run_queues
grab vbl_lock/vblank_time_block amdgpu_vkms_vblank_simulate
amdgpu_vkms_disable_vblank drm_handle_vblank
hrtimer_cancel grab dev->event_lock
So CPU1 stucks in hrtimer_cancel as timer callback is running endless on
current clock base, as that timer queue on CPU2 has no chance to finish it
because of failing to hold the lock. So NMI watchdog will throw the errors
after its threshold, and all later CPUs are impacted/blocked.
So use hrtimer_try_to_cancel to fix this, as disable_vblank callback
does not need to wait the handler to finish. And also it's not necessary
to check the return value of hrtimer_try_to_cancel, because even if it's
-1 which means current timer callback is running, it will be reprogrammed
in hrtimer_start with calling enable_vblank to make it works.
v2: only re-arm timer when vblank is enabled (Christian) and add a Fixes
tag as well
v3: drop warn printing (Christian)
v4: drop superfluous check of blank->enabled in timer function, as it's
guaranteed in drm_handle_vblank (Christian)
Fixes: 84ec374bd580 ("drm/amdgpu: create amdgpu_vkms (v4)")
Cc: stable@vger.kernel.org
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why&How]
DCN301 does not have FAMS hence the workaround needed on other DCN3x
variants related to OTG min/max selector programming is not applicable for it.
Hence isolate it and have it use the old sequence without workaround.
Fixes: 1598fc576420 ("drm/amd/display: Program OTG vtotal min/max selectors unconditionally for DCN1+")
Reviewed-by: Swapnil Patel <swapnil.patel@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why&How]
Make a few functions non static so that they can be reused for other
asic. This is in preparation for separating out OTG programming sequence
for DCN301
Fixes: 1598fc576420 ("drm/amd/display: Program OTG vtotal min/max selectors unconditionally for DCN1+")
Reviewed-by: Swapnil Patel <swapnil.patel@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
SMU7 does a check if the dGPU is inserted into a Rocket Lake system,
to turn off DPM. Extend this check to all systems that have problems
with dynamic switching by using the
amdgpu_device_pcie_dynamic_switching_supported() helper.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Current driver enables backpressure for LBK interfaces.
But these interfaces do not support this feature.
Hence, this patch fixes the issue by skipping the
backpressure configuration for these interfaces.
Fixes: 75f36270990c ("octeontx2-pf: Support to enable/disable pause frames via ethtool").
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Link: https://lore.kernel.org/r/20230716093741.28063-1-gakula@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Cited commit converted the neighbour code to use the standard RCU
variant instead of the RCU-bh variant, but the VRF code still uses
rcu_read_lock_bh() / rcu_read_unlock_bh() around the neighbour lookup
code in its IPv4 and IPv6 output paths, resulting in lockdep splats
[1][2]. Can be reproduced using [3].
Fix by switching to rcu_read_lock() / rcu_read_unlock().
[1]
=============================
WARNING: suspicious RCU usage
6.5.0-rc1-custom-g9c099e6dbf98 #403 Not tainted
-----------------------------
include/net/neighbour.h:302 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
2 locks held by ping/183:
#0: ffff888105ea1d80 (sk_lock-AF_INET){+.+.}-{0:0}, at: raw_sendmsg+0xc6c/0x33c0
#1: ffffffff85b46820 (rcu_read_lock_bh){....}-{1:2}, at: vrf_output+0x2e3/0x2030
stack backtrace:
CPU: 0 PID: 183 Comm: ping Not tainted 6.5.0-rc1-custom-g9c099e6dbf98 #403
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-1.fc37 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0xc1/0xf0
lockdep_rcu_suspicious+0x211/0x3b0
vrf_output+0x1380/0x2030
ip_push_pending_frames+0x125/0x2a0
raw_sendmsg+0x200d/0x33c0
inet_sendmsg+0xa2/0xe0
__sys_sendto+0x2aa/0x420
__x64_sys_sendto+0xe5/0x1c0
do_syscall_64+0x38/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
[2]
=============================
WARNING: suspicious RCU usage
6.5.0-rc1-custom-g9c099e6dbf98 #403 Not tainted
-----------------------------
include/net/neighbour.h:302 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
2 locks held by ping6/182:
#0: ffff888114b63000 (sk_lock-AF_INET6){+.+.}-{0:0}, at: rawv6_sendmsg+0x1602/0x3e50
#1: ffffffff85b46820 (rcu_read_lock_bh){....}-{1:2}, at: vrf_output6+0xe9/0x1310
stack backtrace:
CPU: 0 PID: 182 Comm: ping6 Not tainted 6.5.0-rc1-custom-g9c099e6dbf98 #403
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-1.fc37 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0xc1/0xf0
lockdep_rcu_suspicious+0x211/0x3b0
vrf_output6+0xd32/0x1310
ip6_local_out+0xb4/0x1a0
ip6_send_skb+0xbc/0x340
ip6_push_pending_frames+0xe5/0x110
rawv6_sendmsg+0x2e6e/0x3e50
inet_sendmsg+0xa2/0xe0
__sys_sendto+0x2aa/0x420
__x64_sys_sendto+0xe5/0x1c0
do_syscall_64+0x38/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
[3]
#!/bin/bash
ip link add name vrf-red up numtxqueues 2 type vrf table 10
ip link add name swp1 up master vrf-red type dummy
ip address add 192.0.2.1/24 dev swp1
ip address add 2001:db8:1::1/64 dev swp1
ip neigh add 192.0.2.2 lladdr 00:11:22:33:44:55 nud perm dev swp1
ip neigh add 2001:db8:1::2 lladdr 00:11:22:33:44:55 nud perm dev swp1
ip vrf exec vrf-red ping 192.0.2.2 -c 1 &> /dev/null
ip vrf exec vrf-red ping6 2001:db8:1::2 -c 1 &> /dev/null
Fixes: 09eed1192cec ("neighbour: switch to standard rcu, instead of rcu_bh")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://lore.kernel.org/netdev/CA+G9fYtEr-=GbcXNDYo3XOkwR+uYgehVoDjsP0pFLUpZ_AZcyg@mail.gmail.com/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230715153605.4068066-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-07-14 (ice)
This series contains updates to ice driver only.
Petr Oros removes multiple calls made to unregister netdev and
devlink_port.
Michal fixes null pointer dereference that can occur during reload.
====================
Link: https://lore.kernel.org/r/20230714201041.1717834-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
After activation of interrupts for TPM TIS drivers 0-day reports an
interrupt storm on an Inspur NF5180M6 server.
Fix this by detecting the storm and falling back to polling:
Count the number of unhandled interrupts within a 10 ms time interval. In
case that more than 1000 were unhandled deactivate interrupts entirely,
deregister the handler and use polling instead.
Also print a note to point to the tpm_tis_dmi_table.
Since the interrupt deregistration function devm_free_irq() waits for all
interrupt handlers to finish, only trigger a worker in the interrupt
handler and do the unregistration in the worker to avoid a deadlock.
Note: the storm detection logic equals the implementation in
note_interrupt() which uses timestamps and counters stored in struct
irq_desc. Since this structure is private to the generic interrupt core
the TPM TIS core uses its own timestamps and counters. Furthermore the TPM
interrupt handler always returns IRQ_HANDLED to prevent the generic
interrupt core from processing the interrupt storm.
Cc: stable@vger.kernel.org # v6.4+
Fixes: e644b2f498d2 ("tpm, tpm_tis: Enable interrupt test")
Reported-by: kernel test robot <yujie.liu@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202305041325.ae8b0c43-yujie.liu@intel.com/
Suggested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
The Lenovo L590 suffers from an irq storm issue like the T490, T490s
and P360 Tiny, so add an entry for it to tpm_tis_dmi_table and force
polling.
Cc: stable@vger.kernel.org # v6.4+
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2214069#c0
Fixes: e644b2f498d2 ("tpm, tpm_tis: Enable interrupt test")
Signed-off-by: Florian Bezdeka <florian@bezdeka.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
For Pluton TPM devices, it was assumed that there was no ACPI memory
regions. This is not true for ASUS ROG Ally. ACPI advertises
0xfd500000-0xfd5fffff.
Since remapping is already done in `crb_map_pluton`, remapping again
in `crb_map_io` causes EBUSY error:
[ 3.510453] tpm_crb MSFT0101:00: can't request region for resource [mem 0xfd500000-0xfd5fffff]
[ 3.510463] tpm_crb: probe of MSFT0101:00 failed with error -16
Cc: stable@vger.kernel.org # v6.3+
Fixes: 4d2732882703 ("tpm_crb: Add support for CRB devices based on Pluton")
Signed-off-by: Valentin David <valentin.david@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
This device suffer an irq storm, so add it in tpm_tis_dmi_table to
force polling.
Cc: stable@vger.kernel.org # v6.4+
Link: https://community.frame.work/t/boot-and-shutdown-hangs-with-arch-linux-kernel-6-4-1-mainline-and-arch/33118
Fixes: e644b2f498d2 ("tpm, tpm_tis: Enable interrupt test")
Reported-by: <roubro1991@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217631
Signed-off-by: Christian Hesse <mail@eworm.de>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
This device suffer an irq storm, so add it in tpm_tis_dmi_table to
force polling.
Cc: stable@vger.kernel.org # v6.4+
Link: https://community.frame.work/t/boot-and-shutdown-hangs-with-arch-linux-kernel-6-4-1-mainline-and-arch/33118
Fixes: e644b2f498d2 ("tpm, tpm_tis: Enable interrupt test")
Reported-by: <roubro1991@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217631
Signed-off-by: Christian Hesse <mail@eworm.de>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
tpm_amd_is_rng_defective is for dealing with an issue related to the
AMD firmware TPM, so on non-x86 architectures just have it inline and
return false.
Cc: stable@vger.kernel.org # v6.3+
Reported-by: Sachin Sant <sachinp@linux.ibm.com>
Reported-by: Aneesh Kumar K. V <aneesh.kumar@linux.ibm.com>
Closes: https://lore.kernel.org/lkml/99B81401-DB46-49B9-B321-CF832B50CAC3@linux.ibm.com/
Fixes: f1324bbc4011 ("tpm: disable hwrng for fTPM on some AMD designs")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
Underlying I2C bus drivers not always support longer transfers and
imx-lpi2c for instance doesn't. The fix is symmetric to previous patch
which fixed the read direction.
Cc: stable@vger.kernel.org # v5.20+
Fixes: bbc23a07b072 ("tpm: Add tpm_tis_i2c backend for tpm_tis_core")
Tested-by: Michael Haener <michael.haener@siemens.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
Underlying I2C bus drivers not always support longer transfers and
imx-lpi2c for instance doesn't. SLB 9673 offers 427-bytes packets.
Visible symptoms are:
tpm tpm0: Error left over data
tpm tpm0: tpm_transmit: tpm_recv: error -5
tpm_tis_i2c: probe of 1-002e failed with error -5
Cc: stable@vger.kernel.org # v5.20+
Fixes: bbc23a07b072 ("tpm: Add tpm_tis_i2c backend for tpm_tis_core")
Tested-by: Michael Haener <michael.haener@siemens.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
The failure paths in tpm_tis_spi_transfer() do not deactivate
chip select. Send an empty message (cs_select == 0) to overcome
this.
The patch is tested by two ways.
One way needs to touch hardware:
1. force pull MISO pin down to GND, it emulates a forever
'WAIT' timing.
2. probe cs pin by an oscilloscope.
3. load tpm_tis_spi.ko.
After loading, dmesg prints:
"probe of spi0.0 failed with error -110"
and oscilloscope shows cs pin goes high(deactivated) after
the failure. Before the patch, cs pin keeps low.
Second way is by writing a fake spi controller.
1. implement .transfer_one method, fill all rx buf with 0.
2. implement .set_cs method, print the state of cs pin.
we can see cs goes high after the failure.
Signed-off-by: Peijie Shao <shaopeijie@cestc.cn>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
Further restrict with DMI_PRODUCT_VERSION.
Cc: stable@vger.kernel.org # v6.4+
Link: https://lore.kernel.org/linux-integrity/20230517122931.22385-1-peter.ujfalusi@linux.intel.com/
Fixes: 95a9359ee22f ("tpm: tpm_tis: Disable interrupts for AEON UPX-i11")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
/dev/vtpmx is made visible before 'workqueue' is initialized, which can
lead to a memory corruption in the worst case scenario.
Address this by initializing 'workqueue' as the very first step of the
driver initialization.
Cc: stable@vger.kernel.org
Fixes: 6f99612e2500 ("tpm: Proxy driver for supporting multiple emulated TPMs")
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@tuni.fi>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
The mcp251xfd controller needs an idle bus to enter 'Normal CAN 2.0
mode' or . The maximum length of a CAN frame is 736 bits (64 data
bytes, CAN-FD, EFF mode, worst case bit stuffing and interframe
spacing). For low bit rates like 10 kbit/s the arbitrarily chosen
MCP251XFD_POLL_TIMEOUT_US of 1 ms is too small.
Otherwise during polling for the CAN controller to enter 'Normal CAN
2.0 mode' the timeout limit is exceeded and the configuration fails
with:
| $ ip link set dev can1 up type can bitrate 10000
| [ 731.911072] mcp251xfd spi2.1 can1: Controller failed to enter mode CAN 2.0 Mode (6) and stays in Configuration Mode (4) (con=0x068b0760, osc=0x00000468).
| [ 731.927192] mcp251xfd spi2.1 can1: CRC read error at address 0x0e0c (length=4, data=00 00 00 00, CRC=0x0000) retrying.
| [ 731.938101] A link change request failed with some changes committed already. Interface can1 may have been left with an inconsistent configuration, please check.
| RTNETLINK answers: Connection timed out
Make MCP251XFD_POLL_TIMEOUT_US timeout calculation dynamic. Use
maximum of 1ms and bit time of 1 full 64 data bytes CAN-FD frame in
EFF mode, worst case bit stuffing and interframe spacing at the
current bit rate.
For easier backporting define the macro MCP251XFD_FRAME_LEN_MAX_BITS
that holds the max frame length in bits, which is 736. This can be
replaced by can_frame_bits(true, true, true, true, CANFD_MAX_DLEN) in
a cleanup patch later.
Fixes: 55e5b97f003e8 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20230717-mcp251xfd-fix-increase-poll-timeout-v5-1-06600f34c684@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The reset task is currently scheduled from the watchdog or adminq tasks.
First, all direct calls to schedule the reset task are replaced with the
iavf_schedule_reset(), which is modified to accept the flag showing the
type of reset.
To prevent the reset task from starting once iavf_remove() starts, we need
to check the __IAVF_IN_REMOVE_TASK bit before we schedule it. This is now
easily added to iavf_schedule_reset().
Finally, remove the check for IAVF_FLAG_RESET_NEEDED in the watchdog task.
It is redundant since all callers who set the flag immediately schedules
the reset task.
Fixes: 3ccd54ef44eb ("iavf: Fix init state closure on remove")
Fixes: 14756b2ae265 ("iavf: Fix __IAVF_RESETTING state usage")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
A driver's lock (crit_lock) is used to serialize all the driver's tasks.
Lockdep, however, shows a circular dependency between rtnl and
crit_lock. This happens when an ndo that already holds the rtnl requests
the driver to reset, since the reset task (in some paths) tries to grab
rtnl to either change real number of queues of update netdev features.
[566.241851] ======================================================
[566.241893] WARNING: possible circular locking dependency detected
[566.241936] 6.2.14-100.fc36.x86_64+debug #1 Tainted: G OE
[566.241984] ------------------------------------------------------
[566.242025] repro.sh/2604 is trying to acquire lock:
[566.242061] ffff9280fc5ceee8 (&adapter->crit_lock){+.+.}-{3:3}, at: iavf_close+0x3c/0x240 [iavf]
[566.242167]
but task is already holding lock:
[566.242209] ffffffff9976d350 (rtnl_mutex){+.+.}-{3:3}, at: iavf_remove+0x6b5/0x730 [iavf]
[566.242300]
which lock already depends on the new lock.
[566.242353]
the existing dependency chain (in reverse order) is:
[566.242401]
-> #1 (rtnl_mutex){+.+.}-{3:3}:
[566.242451] __mutex_lock+0xc1/0xbb0
[566.242489] iavf_init_interrupt_scheme+0x179/0x440 [iavf]
[566.242560] iavf_watchdog_task+0x80b/0x1400 [iavf]
[566.242627] process_one_work+0x2b3/0x560
[566.242663] worker_thread+0x4f/0x3a0
[566.242696] kthread+0xf2/0x120
[566.242730] ret_from_fork+0x29/0x50
[566.242763]
-> #0 (&adapter->crit_lock){+.+.}-{3:3}:
[566.242815] __lock_acquire+0x15ff/0x22b0
[566.242869] lock_acquire+0xd2/0x2c0
[566.242901] __mutex_lock+0xc1/0xbb0
[566.242934] iavf_close+0x3c/0x240 [iavf]
[566.242997] __dev_close_many+0xac/0x120
[566.243036] dev_close_many+0x8b/0x140
[566.243071] unregister_netdevice_many_notify+0x165/0x7c0
[566.243116] unregister_netdevice_queue+0xd3/0x110
[566.243157] iavf_remove+0x6c1/0x730 [iavf]
[566.243217] pci_device_remove+0x33/0xa0
[566.243257] device_release_driver_internal+0x1bc/0x240
[566.243299] pci_stop_bus_device+0x6c/0x90
[566.243338] pci_stop_and_remove_bus_device+0xe/0x20
[566.243380] pci_iov_remove_virtfn+0xd1/0x130
[566.243417] sriov_disable+0x34/0xe0
[566.243448] ice_free_vfs+0x2da/0x330 [ice]
[566.244383] ice_sriov_configure+0x88/0xad0 [ice]
[566.245353] sriov_numvfs_store+0xde/0x1d0
[566.246156] kernfs_fop_write_iter+0x15e/0x210
[566.246921] vfs_write+0x288/0x530
[566.247671] ksys_write+0x74/0xf0
[566.248408] do_syscall_64+0x58/0x80
[566.249145] entry_SYSCALL_64_after_hwframe+0x72/0xdc
[566.249886]
other info that might help us debug this:
[566.252014] Possible unsafe locking scenario:
[566.253432] CPU0 CPU1
[566.254118] ---- ----
[566.254800] lock(rtnl_mutex);
[566.255514] lock(&adapter->crit_lock);
[566.256233] lock(rtnl_mutex);
[566.256897] lock(&adapter->crit_lock);
[566.257388]
*** DEADLOCK ***
The deadlock can be triggered by a script that is continuously resetting
the VF adapter while doing other operations requiring RTNL, e.g:
while :; do
ip link set $VF up
ethtool --set-channels $VF combined 2
ip link set $VF down
ip link set $VF up
ethtool --set-channels $VF combined 4
ip link set $VF down
done
Any operation that triggers a reset can substitute "ethtool --set-channles"
As a fix, add a new task "finish_config" that do all the work which
needs rtnl lock. With the exception of iavf_remove(), all work that
require rtnl should be called from this task.
As for iavf_remove(), at the point where we need to call
unregister_netdevice() (and grab rtnl_lock), we make sure the finish_config
task is not running (cancel_work_sync()) to safely grab rtnl. Subsequent
finish_config work cannot restart after that since the task is guarded
by the __IAVF_IN_REMOVE_TASK bit in iavf_schedule_finish_config().
Fixes: 5ac49f3c2702 ("iavf: use mutexes for locking of critical sections")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This reverts commit 08f1c147b7265245d67321585c68a27e990e0c4b.
Netdev is no longer being detached during reset, so this fix can be
reverted. We leave the removal of "hacky" IFF_UP flag update.
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This reverts commit aa626da947e9cd30c4cf727493903e1adbb2c0a0.
Detaching device during reset was not fully fixing the rtnl locking issue,
as there could be a situation where callback was already in progress before
detaching netdev.
Furthermore, detaching netdevice causes TX timeouts if traffic is running.
To reproduce:
ip netns exec ns1 iperf3 -c $PEER_IP -t 600 --logfile /dev/null &
while :; do
for i in 200 7000 400 5000 300 3000 ; do
ip netns exec ns1 ip link set $VF1 mtu $i
sleep 2
done
sleep 10
done
Currently, callbacks such as iavf_change_mtu() wait for the reset.
If the reset fails to acquire the rtnl_lock, they schedule the netdev
update for later while continuing the reset flow. Operations like MTU
changes are performed under the rtnl_lock. Therefore, when the operation
finishes, another callback that uses rtnl_lock can start.
Signed-off-by: Dawid Wesierski <dawidx.wesierski@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There was a fail when trying to add the interface to bonding
right after changing the MTU on the interface. It was caused
by bonding interface unable to open the interface due to
interface being in __RESETTING state because of MTU change.
Add new reset_waitqueue to indicate that reset has finished.
Add waiting for reset to finish in callbacks which trigger hw reset:
iavf_set_priv_flags(), iavf_change_mtu() and iavf_set_ringparam().
We use a 5000ms timeout period because on Hyper-V based systems,
this operation takes around 3000-4000ms. In normal circumstances,
it doesn't take more than 500ms to complete.
Add a function iavf_wait_for_reset() to reuse waiting for reset code and
use it also in iavf_set_channels(), which already waits for reset.
We don't use error handling in iavf_set_channels() as this could
cause the device to be in incorrect state if the reset was scheduled
but hit timeout or the waitng function was interrupted by a signal.
Fixes: 4e5e6b5d9d13 ("iavf: Fix return of set the new channel count")
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Co-developed-by: Dawid Wesierski <dawidx.wesierski@intel.com>
Signed-off-by: Dawid Wesierski <dawidx.wesierski@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
If the system tries to close the netdev while iavf_reset_task() is
running, __LINK_STATE_START will be cleared and netif_running() will
return false in iavf_reinit_interrupt_scheme(). This will result in
iavf_free_traffic_irqs() not being called and a leak as follows:
[7632.489326] remove_proc_entry: removing non-empty directory 'irq/999', leaking at least 'iavf-enp24s0f0v0-TxRx-0'
[7632.490214] WARNING: CPU: 0 PID: 10 at fs/proc/generic.c:718 remove_proc_entry+0x19b/0x1b0
is shown when pci_disable_msix() is later called. Fix by using the
internal adapter state. The traffic IRQs will always exist if
state == __IAVF_RUNNING.
Fixes: 5b36e8d04b44 ("i40evf: Enable VF to request an alternate queue allocation")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
If we set channels greater during iavf_remove(), and waiting reset done
would be timeout, then returned with error but changed num_active_queues
directly, that will lead to OOB like the following logs. Because the
num_active_queues is greater than tx/rx_rings[] allocated actually.
Reproducer:
[root@host ~]# cat repro.sh
#!/bin/bash
pf_dbsf="0000:41:00.0"
vf0_dbsf="0000:41:02.0"
g_pids=()
function do_set_numvf()
{
echo 2 >/sys/bus/pci/devices/${pf_dbsf}/sriov_numvfs
sleep $((RANDOM%3+1))
echo 0 >/sys/bus/pci/devices/${pf_dbsf}/sriov_numvfs
sleep $((RANDOM%3+1))
}
function do_set_channel()
{
local nic=$(ls -1 --indicator-style=none /sys/bus/pci/devices/${vf0_dbsf}/net/)
[ -z "$nic" ] && { sleep $((RANDOM%3)) ; return 1; }
ifconfig $nic 192.168.18.5 netmask 255.255.255.0
ifconfig $nic up
ethtool -L $nic combined 1
ethtool -L $nic combined 4
sleep $((RANDOM%3))
}
function on_exit()
{
local pid
for pid in "${g_pids[@]}"; do
kill -0 "$pid" &>/dev/null && kill "$pid" &>/dev/null
done
g_pids=()
}
trap "on_exit; exit" EXIT
while :; do do_set_numvf ; done &
g_pids+=($!)
while :; do do_set_channel ; done &
g_pids+=($!)
wait
Result:
[ 3506.152887] iavf 0000:41:02.0: Removing device
[ 3510.400799] ==================================================================
[ 3510.400820] BUG: KASAN: slab-out-of-bounds in iavf_free_all_tx_resources+0x156/0x160 [iavf]
[ 3510.400823] Read of size 8 at addr ffff88b6f9311008 by task repro.sh/55536
[ 3510.400823]
[ 3510.400830] CPU: 101 PID: 55536 Comm: repro.sh Kdump: loaded Tainted: G O --------- -t - 4.18.0 #1
[ 3510.400832] Hardware name: Powerleader PR2008AL/H12DSi-N6, BIOS 2.0 04/09/2021
[ 3510.400835] Call Trace:
[ 3510.400851] dump_stack+0x71/0xab
[ 3510.400860] print_address_description+0x6b/0x290
[ 3510.400865] ? iavf_free_all_tx_resources+0x156/0x160 [iavf]
[ 3510.400868] kasan_report+0x14a/0x2b0
[ 3510.400873] iavf_free_all_tx_resources+0x156/0x160 [iavf]
[ 3510.400880] iavf_remove+0x2b6/0xc70 [iavf]
[ 3510.400884] ? iavf_free_all_rx_resources+0x160/0x160 [iavf]
[ 3510.400891] ? wait_woken+0x1d0/0x1d0
[ 3510.400895] ? notifier_call_chain+0xc1/0x130
[ 3510.400903] pci_device_remove+0xa8/0x1f0
[ 3510.400910] device_release_driver_internal+0x1c6/0x460
[ 3510.400916] pci_stop_bus_device+0x101/0x150
[ 3510.400919] pci_stop_and_remove_bus_device+0xe/0x20
[ 3510.400924] pci_iov_remove_virtfn+0x187/0x420
[ 3510.400927] ? pci_iov_add_virtfn+0xe10/0xe10
[ 3510.400929] ? pci_get_subsys+0x90/0x90
[ 3510.400932] sriov_disable+0xed/0x3e0
[ 3510.400936] ? bus_find_device+0x12d/0x1a0
[ 3510.400953] i40e_free_vfs+0x754/0x1210 [i40e]
[ 3510.400966] ? i40e_reset_all_vfs+0x880/0x880 [i40e]
[ 3510.400968] ? pci_get_device+0x7c/0x90
[ 3510.400970] ? pci_get_subsys+0x90/0x90
[ 3510.400982] ? pci_vfs_assigned.part.7+0x144/0x210
[ 3510.400987] ? __mutex_lock_slowpath+0x10/0x10
[ 3510.400996] i40e_pci_sriov_configure+0x1fa/0x2e0 [i40e]
[ 3510.401001] sriov_numvfs_store+0x214/0x290
[ 3510.401005] ? sriov_totalvfs_show+0x30/0x30
[ 3510.401007] ? __mutex_lock_slowpath+0x10/0x10
[ 3510.401011] ? __check_object_size+0x15a/0x350
[ 3510.401018] kernfs_fop_write+0x280/0x3f0
[ 3510.401022] vfs_write+0x145/0x440
[ 3510.401025] ksys_write+0xab/0x160
[ 3510.401028] ? __ia32_sys_read+0xb0/0xb0
[ 3510.401031] ? fput_many+0x1a/0x120
[ 3510.401032] ? filp_close+0xf0/0x130
[ 3510.401038] do_syscall_64+0xa0/0x370
[ 3510.401041] ? page_fault+0x8/0x30
[ 3510.401043] entry_SYSCALL_64_after_hwframe+0x65/0xca
[ 3510.401073] RIP: 0033:0x7f3a9bb842c0
[ 3510.401079] Code: 73 01 c3 48 8b 0d d8 cb 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 89 24 2d 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 fe dd 01 00 48 89 04 24
[ 3510.401080] RSP: 002b:00007ffc05f1fe18 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 3510.401083] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007f3a9bb842c0
[ 3510.401085] RDX: 0000000000000002 RSI: 0000000002327408 RDI: 0000000000000001
[ 3510.401086] RBP: 0000000002327408 R08: 00007f3a9be53780 R09: 00007f3a9c8a4700
[ 3510.401086] R10: 0000000000000001 R11: 0000000000000246 R12: 0000000000000002
[ 3510.401087] R13: 0000000000000001 R14: 00007f3a9be52620 R15: 0000000000000001
[ 3510.401090]
[ 3510.401093] Allocated by task 76795:
[ 3510.401098] kasan_kmalloc+0xa6/0xd0
[ 3510.401099] __kmalloc+0xfb/0x200
[ 3510.401104] iavf_init_interrupt_scheme+0x26f/0x1310 [iavf]
[ 3510.401108] iavf_watchdog_task+0x1d58/0x4050 [iavf]
[ 3510.401114] process_one_work+0x56a/0x11f0
[ 3510.401115] worker_thread+0x8f/0xf40
[ 3510.401117] kthread+0x2a0/0x390
[ 3510.401119] ret_from_fork+0x1f/0x40
[ 3510.401122] 0xffffffffffffffff
[ 3510.401123]
In timeout handling, we should keep the original num_active_queues
and reset num_req_queues to 0.
Fixes: 4e5e6b5d9d13 ("iavf: Fix return of set the new channel count")
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Cc: Donglin Peng <pengdonglin@sangfor.com.cn>
Cc: Huang Cun <huangcun@sangfor.com.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
We do netif_napi_add() for all allocated q_vectors[], but potentially
do netif_napi_del() for part of them, then kfree q_vectors and leave
invalid pointers at dev->napi_list.
Reproducer:
[root@host ~]# cat repro.sh
#!/bin/bash
pf_dbsf="0000:41:00.0"
vf0_dbsf="0000:41:02.0"
g_pids=()
function do_set_numvf()
{
echo 2 >/sys/bus/pci/devices/${pf_dbsf}/sriov_numvfs
sleep $((RANDOM%3+1))
echo 0 >/sys/bus/pci/devices/${pf_dbsf}/sriov_numvfs
sleep $((RANDOM%3+1))
}
function do_set_channel()
{
local nic=$(ls -1 --indicator-style=none /sys/bus/pci/devices/${vf0_dbsf}/net/)
[ -z "$nic" ] && { sleep $((RANDOM%3)) ; return 1; }
ifconfig $nic 192.168.18.5 netmask 255.255.255.0
ifconfig $nic up
ethtool -L $nic combined 1
ethtool -L $nic combined 4
sleep $((RANDOM%3))
}
function on_exit()
{
local pid
for pid in "${g_pids[@]}"; do
kill -0 "$pid" &>/dev/null && kill "$pid" &>/dev/null
done
g_pids=()
}
trap "on_exit; exit" EXIT
while :; do do_set_numvf ; done &
g_pids+=($!)
while :; do do_set_channel ; done &
g_pids+=($!)
wait
Result:
[ 4093.900222] ==================================================================
[ 4093.900230] BUG: KASAN: use-after-free in free_netdev+0x308/0x390
[ 4093.900232] Read of size 8 at addr ffff88b4dc145640 by task repro.sh/6699
[ 4093.900233]
[ 4093.900236] CPU: 10 PID: 6699 Comm: repro.sh Kdump: loaded Tainted: G O --------- -t - 4.18.0 #1
[ 4093.900238] Hardware name: Powerleader PR2008AL/H12DSi-N6, BIOS 2.0 04/09/2021
[ 4093.900239] Call Trace:
[ 4093.900244] dump_stack+0x71/0xab
[ 4093.900249] print_address_description+0x6b/0x290
[ 4093.900251] ? free_netdev+0x308/0x390
[ 4093.900252] kasan_report+0x14a/0x2b0
[ 4093.900254] free_netdev+0x308/0x390
[ 4093.900261] iavf_remove+0x825/0xd20 [iavf]
[ 4093.900265] pci_device_remove+0xa8/0x1f0
[ 4093.900268] device_release_driver_internal+0x1c6/0x460
[ 4093.900271] pci_stop_bus_device+0x101/0x150
[ 4093.900273] pci_stop_and_remove_bus_device+0xe/0x20
[ 4093.900275] pci_iov_remove_virtfn+0x187/0x420
[ 4093.900277] ? pci_iov_add_virtfn+0xe10/0xe10
[ 4093.900278] ? pci_get_subsys+0x90/0x90
[ 4093.900280] sriov_disable+0xed/0x3e0
[ 4093.900282] ? bus_find_device+0x12d/0x1a0
[ 4093.900290] i40e_free_vfs+0x754/0x1210 [i40e]
[ 4093.900298] ? i40e_reset_all_vfs+0x880/0x880 [i40e]
[ 4093.900299] ? pci_get_device+0x7c/0x90
[ 4093.900300] ? pci_get_subsys+0x90/0x90
[ 4093.900306] ? pci_vfs_assigned.part.7+0x144/0x210
[ 4093.900309] ? __mutex_lock_slowpath+0x10/0x10
[ 4093.900315] i40e_pci_sriov_configure+0x1fa/0x2e0 [i40e]
[ 4093.900318] sriov_numvfs_store+0x214/0x290
[ 4093.900320] ? sriov_totalvfs_show+0x30/0x30
[ 4093.900321] ? __mutex_lock_slowpath+0x10/0x10
[ 4093.900323] ? __check_object_size+0x15a/0x350
[ 4093.900326] kernfs_fop_write+0x280/0x3f0
[ 4093.900329] vfs_write+0x145/0x440
[ 4093.900330] ksys_write+0xab/0x160
[ 4093.900332] ? __ia32_sys_read+0xb0/0xb0
[ 4093.900334] ? fput_many+0x1a/0x120
[ 4093.900335] ? filp_close+0xf0/0x130
[ 4093.900338] do_syscall_64+0xa0/0x370
[ 4093.900339] ? page_fault+0x8/0x30
[ 4093.900341] entry_SYSCALL_64_after_hwframe+0x65/0xca
[ 4093.900357] RIP: 0033:0x7f16ad4d22c0
[ 4093.900359] Code: 73 01 c3 48 8b 0d d8 cb 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 89 24 2d 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 fe dd 01 00 48 89 04 24
[ 4093.900360] RSP: 002b:00007ffd6491b7f8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 4093.900362] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007f16ad4d22c0
[ 4093.900363] RDX: 0000000000000002 RSI: 0000000001a41408 RDI: 0000000000000001
[ 4093.900364] RBP: 0000000001a41408 R08: 00007f16ad7a1780 R09: 00007f16ae1f2700
[ 4093.900364] R10: 0000000000000001 R11: 0000000000000246 R12: 0000000000000002
[ 4093.900365] R13: 0000000000000001 R14: 00007f16ad7a0620 R15: 0000000000000001
[ 4093.900367]
[ 4093.900368] Allocated by task 820:
[ 4093.900371] kasan_kmalloc+0xa6/0xd0
[ 4093.900373] __kmalloc+0xfb/0x200
[ 4093.900376] iavf_init_interrupt_scheme+0x63b/0x1320 [iavf]
[ 4093.900380] iavf_watchdog_task+0x3d51/0x52c0 [iavf]
[ 4093.900382] process_one_work+0x56a/0x11f0
[ 4093.900383] worker_thread+0x8f/0xf40
[ 4093.900384] kthread+0x2a0/0x390
[ 4093.900385] ret_from_fork+0x1f/0x40
[ 4093.900387] 0xffffffffffffffff
[ 4093.900387]
[ 4093.900388] Freed by task 6699:
[ 4093.900390] __kasan_slab_free+0x137/0x190
[ 4093.900391] kfree+0x8b/0x1b0
[ 4093.900394] iavf_free_q_vectors+0x11d/0x1a0 [iavf]
[ 4093.900397] iavf_remove+0x35a/0xd20 [iavf]
[ 4093.900399] pci_device_remove+0xa8/0x1f0
[ 4093.900400] device_release_driver_internal+0x1c6/0x460
[ 4093.900401] pci_stop_bus_device+0x101/0x150
[ 4093.900402] pci_stop_and_remove_bus_device+0xe/0x20
[ 4093.900403] pci_iov_remove_virtfn+0x187/0x420
[ 4093.900404] sriov_disable+0xed/0x3e0
[ 4093.900409] i40e_free_vfs+0x754/0x1210 [i40e]
[ 4093.900415] i40e_pci_sriov_configure+0x1fa/0x2e0 [i40e]
[ 4093.900416] sriov_numvfs_store+0x214/0x290
[ 4093.900417] kernfs_fop_write+0x280/0x3f0
[ 4093.900418] vfs_write+0x145/0x440
[ 4093.900419] ksys_write+0xab/0x160
[ 4093.900420] do_syscall_64+0xa0/0x370
[ 4093.900421] entry_SYSCALL_64_after_hwframe+0x65/0xca
[ 4093.900422] 0xffffffffffffffff
[ 4093.900422]
[ 4093.900424] The buggy address belongs to the object at ffff88b4dc144200
which belongs to the cache kmalloc-8k of size 8192
[ 4093.900425] The buggy address is located 5184 bytes inside of
8192-byte region [ffff88b4dc144200, ffff88b4dc146200)
[ 4093.900425] The buggy address belongs to the page:
[ 4093.900427] page:ffffea00d3705000 refcount:1 mapcount:0 mapping:ffff88bf04415c80 index:0x0 compound_mapcount: 0
[ 4093.900430] flags: 0x10000000008100(slab|head)
[ 4093.900433] raw: 0010000000008100 dead000000000100 dead000000000200 ffff88bf04415c80
[ 4093.900434] raw: 0000000000000000 0000000000030003 00000001ffffffff 0000000000000000
[ 4093.900434] page dumped because: kasan: bad access detected
[ 4093.900435]
[ 4093.900435] Memory state around the buggy address:
[ 4093.900436] ffff88b4dc145500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 4093.900437] ffff88b4dc145580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 4093.900438] >ffff88b4dc145600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 4093.900438] ^
[ 4093.900439] ffff88b4dc145680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 4093.900440] ffff88b4dc145700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 4093.900440] ==================================================================
Although the patch #2 (of 2) can avoid the issue triggered by this
repro.sh, there still are other potential risks that if num_active_queues
is changed to less than allocated q_vectors[] by unexpected, the
mismatched netif_napi_add/del() can also cause UAF.
Since we actually call netif_napi_add() for all allocated q_vectors
unconditionally in iavf_alloc_q_vectors(), so we should fix it by
letting netif_napi_del() match to netif_napi_add().
Fixes: 5eae00c57f5e ("i40evf: main driver core")
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Cc: Donglin Peng <pengdonglin@sangfor.com.cn>
Cc: Huang Cun <huangcun@sangfor.com.cn>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This reverts commit 88e9664434c994e97a9f6f8cdd1535495c660cea.
__diag_ignore_all() only works for GCC 8 or later.
-Woverride-init (from -Wextra, enabled in i915 Makefile) combined with
CONFIG_WERROR=y or W=e breaks the build for older GCC.
With i386_defconfig and x86_64_defconfig enabling CONFIG_WERROR=y by
default, we really need to roll back the change.
An alternative would be to disable -Woverride-init in the Makefile for
GCC <8, but the revert seems like the safest bet now.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8768
Reported-by: John Garry <john.g.garry@oracle.com>
References: https://lore.kernel.org/r/ad2601c0-84bb-c574-3702-a83ff8faf98c@oracle.com
References: https://lore.kernel.org/r/87wmzezns4.fsf@intel.com
Fixes: 88e9664434c9 ("drm/i915: use localized __diag_ignore_all() instead of per file")
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Tested-by: John Garry <john.g.garry@oracle.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230711110214.25093-1-jani.nikula@intel.com
(cherry picked from commit 290d161045753240f2100b8f44660426ecc97be5)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
Arrays passed to reg_in_range_table should end with empty record.
The patch solves KASAN detected bug with signature:
BUG: KASAN: global-out-of-bounds in xehp_is_valid_b_counter_addr+0x2c7/0x350 [i915]
Read of size 4 at addr ffffffffa1555d90 by task perf/1518
CPU: 4 PID: 1518 Comm: perf Tainted: G U 6.4.0-kasan_438-g3303d06107f3+ #1
Hardware name: Intel Corporation Meteor Lake Client Platform/MTL-P DDR5 SODIMM SBS RVP, BIOS MTLPFWI1.R00.3223.D80.2305311348 05/31/2023
Call Trace:
<TASK>
...
xehp_is_valid_b_counter_addr+0x2c7/0x350 [i915]
Fixes: 0fa9349dda03 ("drm/i915/perf: complete programming whitelisting for XEHPSDV")
Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230711153410.1224997-1-andrzej.hajda@intel.com
(cherry picked from commit 2f42c5afb34b5696cf5fe79e744f99be9b218798)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|