Age | Commit message (Collapse) | Author | Files | Lines |
|
[ Upstream commit 617f5db1a626f18d5cbb7c7faf7bf8f9ea12be78 ]
The cited commit aimed to ensure that Virtual Functions (VFs) assign a
queue affinity to a Queue Pair (QP) to distribute traffic when
the LAG master creates a hardware LAG. If the affinity was set while
the hardware was not in LAG, the firmware would ignore the affinity value.
However, this commit unintentionally assigned an affinity to QPs on the LAG
master's VPORT even if the RDMA device was not marked as LAG-enabled.
In most cases, this was not an issue because when the hardware entered
hardware LAG configuration, the RDMA device of the LAG master would be
destroyed and a new one would be created, marked as LAG-enabled.
The problem arises when a user configures Equal-Cost Multipath (ECMP).
In ECMP mode, traffic can be directed to different physical ports based on
the queue affinity, which is intended for use by VPORTS other than the
E-Switch manager. ECMP mode is supported only if both E-Switch managers are
in switchdev mode and the appropriate route is configured via IP. In this
configuration, the RDMA device is not destroyed, and we retain the RDMA
device that is not marked as LAG-enabled.
To ensure correct behavior, Send Queues (SQs) opened by the E-Switch
manager through verbs should be assigned strict affinity. This means they
will only be able to communicate through the native physical port
associated with the E-Switch manager. This will prevent the firmware from
assigning affinity and will not allow the SQs to be remapped in case of
failover.
Fixes: 802dcc7fc5ec ("RDMA/mlx5: Support TX port affinity for VF drivers in LAG mode")
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://lore.kernel.org/r/425b05f4da840bc684b0f7e8ebf61aeb5cef09b0.1685960567.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c7dd225bc224726c22db08e680bf787f60ebdee3 upstream.
SW Steering uses RC QP for writing STEs to ICM. This writingis done in LB
(loopback), and FL (force-loopback) QP is preferred for performance. FL is
available when RoCE is enabled or disabled based on RoCE caps.
This patch adds reading of FL capability from HCA caps in addition to the
existing reading from RoCE caps, thus fixing the case where we didn't
have loopback enabled when RoCE was disabled.
Fixes: 7304d603a57a ("net/mlx5: DR, Add support for force-loopback QP")
Signed-off-by: Itamar Gozlan <igozlan@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3e358ea8614ddfbc59ca7a3f5dff5dde2b350b2c ]
Commit cited in "fixes" tag added bulk support for flow counters but it
didn't account that's also possible to query a counter using a non-base id
if the counter was allocated as bulk.
When a user performs a query, validate the flow counter id given in the
mailbox is inside the valid range taking bulk value into account.
Fixes: 208d70f562e5 ("IB/mlx5: Support flow counters offset for bulk counters")
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Link: https://lore.kernel.org/r/79d7fbe291690128e44672418934256254d93115.1681377114.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9965bbebae59b3563a4d95e4aed121e8965dfdc2 ]
Currently, each core device has VF pages counter which stores number of
fw pages used by its VFs and SFs.
The current design led to a hang when performing firmware reset on DPU,
where the DPU PFs stalled in sriov unload flow due to waiting on release
of SFs pages instead of waiting on only VFs pages.
Thus, Add a separate counter for SF firmware pages, which will prevent
the stall scenario described above.
Fixes: 1958fc2f0712 ("net/mlx5: SF, Add auxiliary device driver")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c3bdbaea654d8df39112de33037106134a520dc7 ]
Currently, an independent page counter is used for tracking memory usage
for each function type such as VF, PF and host PF (DPU).
For better code-readibilty, use a single array that stores
the number of allocated memory pages for each function type.
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: 9965bbebae59 ("net/mlx5: Expose SF firmware pages counter")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit da2e552b469a0cd130ff70a88ccc4139da428a65 ]
Command may fail while driver is reloading and can't accept FW commands
till command interface is reinitialized. Such command failure is being
logged to command stats. This results in NULL pointer access as command
stats structure is being freed and reallocated during mlx5 devlink
reload (see kernel log below).
Fix it by making command stats statically allocated on driver probe.
Kernel log:
[ 2394.808802] BUG: unable to handle kernel paging request at 000000000002a9c0
[ 2394.810610] PGD 0 P4D 0
[ 2394.811811] Oops: 0002 [#1] SMP NOPTI
...
[ 2394.815482] RIP: 0010:native_queued_spin_lock_slowpath+0x183/0x1d0
...
[ 2394.829505] Call Trace:
[ 2394.830667] _raw_spin_lock_irq+0x23/0x26
[ 2394.831858] cmd_status_err+0x55/0x110 [mlx5_core]
[ 2394.833020] mlx5_access_reg+0xe7/0x150 [mlx5_core]
[ 2394.834175] mlx5_query_port_ptys+0x78/0xa0 [mlx5_core]
[ 2394.835337] mlx5e_ethtool_get_link_ksettings+0x74/0x590 [mlx5_core]
[ 2394.836454] ? kmem_cache_alloc_trace+0x140/0x1c0
[ 2394.837562] __rh_call_get_link_ksettings+0x33/0x100
[ 2394.838663] ? __rtnl_unlock+0x25/0x50
[ 2394.839755] __ethtool_get_link_ksettings+0x72/0x150
[ 2394.840862] duplex_show+0x6e/0xc0
[ 2394.841963] dev_attr_show+0x1c/0x40
[ 2394.843048] sysfs_kf_seq_show+0x9b/0x100
[ 2394.844123] seq_read+0x153/0x410
[ 2394.845187] vfs_read+0x91/0x140
[ 2394.846226] ksys_read+0x4f/0xb0
[ 2394.847234] do_syscall_64+0x5b/0x1a0
[ 2394.848228] entry_SYSCALL_64_after_hwframe+0x65/0xca
Fixes: 34f46ae0d4b3 ("net/mlx5: Add command failures data to debugfs")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1f0ae22ab470946143485a02cc1cd7e05c0f9120 ]
Fix SRIOV VST mode behavior to insert cvlan when a guest tag is already
present in the frame. Previous VST mode behavior was to drop packets or
override existing tag, depending on the device version.
In this patch we fix this behavior by correctly building the HW steering
rule with a push vlan action, or for older devices we ask the FW to stack
the vlan when a vlan is already present.
Fixes: 07bab9502641 ("net/mlx5: E-Switch, Refactor eswitch ingress acl codes")
Fixes: dfcb1ed3c331 ("net/mlx5: E-Switch, Vport ingress/egress ACLs rules for VST mode")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
While moving to new CMD API (quiet API), some pre-existing flows may call the new API
function that in case of error, returns the error instead of printing it as previously done.
For such flows we bring back the print but to tracepoint this time for sys admins to
have the ability to check for errors especially for commands using the new quiet API.
Tracepoint output example:
devlink-1333 [001] ..... 822.746922: mlx5_cmd: ACCESS_REG(0x805) op_mod(0x0) failed, status bad resource(0x5), syndrome (0xb06e1f), err(-22)
Fixes: f23519e542e5 ("net/mlx5: cmdif, Add new api for command execution")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
mlx5_cmd_cleanup_async_ctx should return only after all its callback
handlers were completed. Before this patch, the below race between
mlx5_cmd_cleanup_async_ctx and mlx5_cmd_exec_cb_handler was possible and
lead to a use-after-free:
1. mlx5_cmd_cleanup_async_ctx is called while num_inflight is 2 (i.e.
elevated by 1, a single inflight callback).
2. mlx5_cmd_cleanup_async_ctx decreases num_inflight to 1.
3. mlx5_cmd_exec_cb_handler is called, decreases num_inflight to 0 and
is about to call wake_up().
4. mlx5_cmd_cleanup_async_ctx calls wait_event, which returns
immediately as the condition (num_inflight == 0) holds.
5. mlx5_cmd_cleanup_async_ctx returns.
6. The caller of mlx5_cmd_cleanup_async_ctx frees the mlx5_async_ctx
object.
7. mlx5_cmd_exec_cb_handler goes on and calls wake_up() on the freed
object.
Fix it by syncing using a completion object. Mark it completed when
num_inflight reaches 0.
Trace:
BUG: KASAN: use-after-free in do_raw_spin_lock+0x23d/0x270
Read of size 4 at addr ffff888139cd12f4 by task swapper/5/0
CPU: 5 PID: 0 Comm: swapper/5 Not tainted 6.0.0-rc3_for_upstream_debug_2022_08_30_13_10 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0x57/0x7d
print_report.cold+0x2d5/0x684
? do_raw_spin_lock+0x23d/0x270
kasan_report+0xb1/0x1a0
? do_raw_spin_lock+0x23d/0x270
do_raw_spin_lock+0x23d/0x270
? rwlock_bug.part.0+0x90/0x90
? __delete_object+0xb8/0x100
? lock_downgrade+0x6e0/0x6e0
_raw_spin_lock_irqsave+0x43/0x60
? __wake_up_common_lock+0xb9/0x140
__wake_up_common_lock+0xb9/0x140
? __wake_up_common+0x650/0x650
? destroy_tis_callback+0x53/0x70 [mlx5_core]
? kasan_set_track+0x21/0x30
? destroy_tis_callback+0x53/0x70 [mlx5_core]
? kfree+0x1ba/0x520
? do_raw_spin_unlock+0x54/0x220
mlx5_cmd_exec_cb_handler+0x136/0x1a0 [mlx5_core]
? mlx5_cmd_cleanup_async_ctx+0x220/0x220 [mlx5_core]
? mlx5_cmd_cleanup_async_ctx+0x220/0x220 [mlx5_core]
mlx5_cmd_comp_handler+0x65a/0x12b0 [mlx5_core]
? dump_command+0xcc0/0xcc0 [mlx5_core]
? lockdep_hardirqs_on_prepare+0x400/0x400
? cmd_comp_notifier+0x7e/0xb0 [mlx5_core]
cmd_comp_notifier+0x7e/0xb0 [mlx5_core]
atomic_notifier_call_chain+0xd7/0x1d0
mlx5_eq_async_int+0x3ce/0xa20 [mlx5_core]
atomic_notifier_call_chain+0xd7/0x1d0
? irq_release+0x140/0x140 [mlx5_core]
irq_int_handler+0x19/0x30 [mlx5_core]
__handle_irq_event_percpu+0x1f2/0x620
handle_irq_event+0xb2/0x1d0
handle_edge_irq+0x21e/0xb00
__common_interrupt+0x79/0x1a0
common_interrupt+0x78/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
RIP: 0010:default_idle+0x42/0x60
Code: c1 83 e0 07 48 c1 e9 03 83 c0 03 0f b6 14 11 38 d0 7c 04 84 d2 75 14 8b 05 eb 47 22 02 85 c0 7e 07 0f 00 2d e0 9f 48 00 fb f4 <c3> 48 c7 c7 80 08 7f 85 e8 d1 d3 3e fe eb de 66 66 2e 0f 1f 84 00
RSP: 0018:ffff888100dbfdf0 EFLAGS: 00000242
RAX: 0000000000000001 RBX: ffffffff84ecbd48 RCX: 1ffffffff0afe110
RDX: 0000000000000004 RSI: 0000000000000000 RDI: ffffffff835cc9bc
RBP: 0000000000000005 R08: 0000000000000001 R09: ffff88881dec4ac3
R10: ffffed1103bd8958 R11: 0000017d0ca571c9 R12: 0000000000000005
R13: ffffffff84f024e0 R14: 0000000000000000 R15: dffffc0000000000
? default_idle_call+0xcc/0x450
default_idle_call+0xec/0x450
do_idle+0x394/0x450
? arch_cpu_idle_exit+0x40/0x40
? do_idle+0x17/0x450
cpu_startup_entry+0x19/0x20
start_secondary+0x221/0x2b0
? set_cpu_sibling_map+0x2070/0x2070
secondary_startup_64_no_verify+0xcd/0xdb
</TASK>
Allocated by task 49502:
kasan_save_stack+0x1e/0x40
__kasan_kmalloc+0x81/0xa0
kvmalloc_node+0x48/0xe0
mlx5e_bulk_async_init+0x35/0x110 [mlx5_core]
mlx5e_tls_priv_tx_list_cleanup+0x84/0x3e0 [mlx5_core]
mlx5e_ktls_cleanup_tx+0x38f/0x760 [mlx5_core]
mlx5e_cleanup_nic_tx+0xa7/0x100 [mlx5_core]
mlx5e_detach_netdev+0x1ca/0x2b0 [mlx5_core]
mlx5e_suspend+0xdb/0x140 [mlx5_core]
mlx5e_remove+0x89/0x190 [mlx5_core]
auxiliary_bus_remove+0x52/0x70
device_release_driver_internal+0x40f/0x650
driver_detach+0xc1/0x180
bus_remove_driver+0x125/0x2f0
auxiliary_driver_unregister+0x16/0x50
mlx5e_cleanup+0x26/0x30 [mlx5_core]
cleanup+0xc/0x4e [mlx5_core]
__x64_sys_delete_module+0x2b5/0x450
do_syscall_64+0x3d/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Freed by task 49502:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_set_free_info+0x20/0x30
____kasan_slab_free+0x11d/0x1b0
kfree+0x1ba/0x520
mlx5e_tls_priv_tx_list_cleanup+0x2e7/0x3e0 [mlx5_core]
mlx5e_ktls_cleanup_tx+0x38f/0x760 [mlx5_core]
mlx5e_cleanup_nic_tx+0xa7/0x100 [mlx5_core]
mlx5e_detach_netdev+0x1ca/0x2b0 [mlx5_core]
mlx5e_suspend+0xdb/0x140 [mlx5_core]
mlx5e_remove+0x89/0x190 [mlx5_core]
auxiliary_bus_remove+0x52/0x70
device_release_driver_internal+0x40f/0x650
driver_detach+0xc1/0x180
bus_remove_driver+0x125/0x2f0
auxiliary_driver_unregister+0x16/0x50
mlx5e_cleanup+0x26/0x30 [mlx5_core]
cleanup+0xc/0x4e [mlx5_core]
__x64_sys_delete_module+0x2b5/0x450
do_syscall_64+0x3d/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes: e355477ed9e4 ("net/mlx5: Make mlx5_cmd_exec_cb() a safe API")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-8-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull rdma updates from Jason Gunthorpe:
"Not a big list of changes this cycle, mostly small things. The new
MANA rdma driver should come next cycle along with a bunch of work on
rxe.
Summary:
- Small bug fixes in mlx5, efa, rxe, hns, irdma, erdma, siw
- rts tracing improvements
- Code improvements: strlscpy conversion, unused parameter, spelling
mistakes, unused variables, flex arrays
- restrack device details report for hns
- Simplify struct device initialization in SRP
- Eliminate the never-used service_mask support in IB CM
- Make rxe not print to the console for some kinds of network packets
- Asymetric paths and router support in the CM through netlink
messages
- DMABUF importer support for mlx5devx umem's"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (84 commits)
RDMA/rxe: Remove error/warning messages from packet receiver path
RDMA/usnic: fix set-but-not-unused variable 'flags' warning
IB/hfi1: Use skb_put_data() instead of skb_put/memcpy pair
RDMA/hns: Unified Log Printing Style
RDMA/hns: Replacing magic number with macros in apply_func_caps()
RDMA/hns: Repacing 'dseg_len' by macros in fill_ext_sge_inl_data()
RDMA/hns: Remove redundant 'max_srq_desc_sz' in caps
RDMA/hns: Remove redundant 'num_mtt_segs' and 'max_extend_sg'
RDMA/hns: Remove redundant 'phy_addr' in hns_roce_hem_list_find_mtt()
RDMA/hns: Remove redundant 'use_lowmem' argument from hns_roce_init_hem_table()
RDMA/hns: Remove redundant 'bt_level' for hem_list_alloc_item()
RDMA/hns: Remove redundant 'attr_mask' in modify_qp_init_to_init()
RDMA/hns: Remove unnecessary brackets when getting point
RDMA/hns: Remove unnecessary braces for single statement blocks
RDMA/hns: Cleanup for a spelling error of Asynchronous
IB/rdmavt: Add __init/__exit annotations to module init/exit funcs
RDMA/rxe: Remove redundant num_sge fields
RDMA/mlx5: Enable ATS support for MRs and umems
RDMA/mlx5: Add support for dmabuf to devx umem
RDMA/core: Add UVERBS_ATTR_RAW_FD
...
|
|
Trvial merge conflicts against rdma.git for-rc resolved matching
linux-next:
drivers/infiniband/hw/hns/hns_roce_hw_v2.c
drivers/infiniband/hw/hns/hns_roce_main.c
https://lore.kernel.org/r/20220929124005.105149-1-broonie@kernel.org
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Start health poll at earlier stage, so if fw fatal issue occurred before
or during initialization commands such as init_hca or set_hca_cap the
poll health can detect and indicate that the driver is already in error
state.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the rx_oversize_pkts_buffer counter to ethtool statistics.
This counter exposes the number of dropped received packets due to
length which arrived to RQ and exceed software buffer size allocated by
the device for incoming traffic. It might imply that the device MTU is
larger than the software buffers size.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Instead of passing the unaligned flag, pass an enum that indicates the
UMR mode. The next commit will add the third mode (KLM for certain
configurations of XSK), which will be added to this enum instead of
adding another bool flag everywhere.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
UMR MTTs used in striding RQ have certain alignment requirements. While
it's guaranteed to work when UMR pages are aligned to the UMR page size,
in practice it works then UMR pages are aligned to 8 bytes. However,
it's still not enough flexibility for the unaligned mode of XSK. This
patch leverages KSM to map UMR pages without alignment requirements,
when unaligned XSK is active. The downside is that KSM entries are twice
as big as MTTs, which limits the maximum WQE size, so regular RQs and
aligned XSK continue using MTTs.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This commit allows striding RQ to determine MTT page size at runtime,
instead of sticking to the compile-time PAGE_SIZE. This functionality
will be used by a following commit that adjusts the MTT page size to the
XSK frame size.
Stick with PAGE_SIZE for XSK on legacy RQ, as frag_stride is not used in
data path, it only helps calculate how pages are partitioned into
fragments, and PAGE_SIZE will ensure each fragment starts at the
beginning of a new allocation unit (XSK frame).
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the capability that will allow the driver to determine the minimal
MTT page size to be able to map the smallest possible pages in XSK. The
older firmwares that don't have this capability default to 12 (i.e.
4096-byte pages).
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
updates from mlx5-next 2022-09-24
Updates form mlx5-next including[1]:
1) HW definitions and support for NPPS clock settings.
2) various cleanups
3) Enable hash mode by default for all NICs
4) page tracker and advanced virtualization HW definitions for vfio
[1] https://lore.kernel.org/netdev/20220907233636.388475-1-saeed@kernel.org/
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Remove from FPGA IFC file not-needed definitions
net/mlx5: Remove unused structs
net/mlx5: Remove unused functions
net/mlx5: detect and enable bypass port select flow table
net/mlx5: Lag, enable hash mode by default for all NICs
net/mlx5: Lag, set active ports if support bypass port select flow table
RDMA/mlx5: Don't set tx affinity when lag is in hash mode
net/mlx5: add IFC bits for bypassing port select flow table
net/mlx5: Add support for NPPS with real time mode
net/mlx5: Expose NPPS related registers
net/mlx5: Query ADV_VIRTUALIZATION capabilities
net/mlx5: Introduce ifc bits for page tracker
RDMA/mlx5: Move function mlx5_core_query_ib_ppcnt() to mlx5_ib
====================
Link: https://lore.kernel.org/all/20220927201906.234015-1-saeed@kernel.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move IP layout bits definitions to be close to the place that actually
uses it, together with removal extra defines that not in-use.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Remove structs which are no longer used in the driver:
mlx5dr_cmd_qp_create_attr
mlx5_fs_dr_ns
mlx5_pas
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Remove functions which are no longer used in the driver:
mlx5e_ipsec_is_tx_flow
mlx5_health_flush
get_cqe_enhanced_num_mini_cqes
get_cqe_l3_hdr_type
mlx5_health_flush
mlx5_fs_is_ipsec_flow
_mlx5_fs_is_outer_ipproto_flow
mlx5_fs_is_outer_tcp_flow
mlx5_fs_is_outer_udp_flow
mlx5_fs_is_vxlan_flow
mlx5_fs_is_outer_ipsec_flow
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In hash mode, without setting tx affinity explicitly, the port select
flow table decides which port is used for the traffic.
If port_select_flow_table_bypass capability is supported and tx affinity
is set explicitly for QP/TIS, they will be added into the explicit affinity
table in FW to check which port is used for the traffic.
1. The overloaded explicit affinity table may affect performance.
To avoid this, do not set tx affinity explicitly by default.
2. The packets of the same flow need to be transmitted on the same port.
Because the packets of the same flow use different QPs in slow & fast
path, it shouldn't set tx affinity explicitly for these QPs.
Signed-off-by: Liu, Changcheng <jerrliu@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
port_select_flow_table_bypass - When set, device supports
bypass port select flow table.
active_port - Bitmask indicates the current active ports
in PORT_SELECT_FT LAG.
MLX5_SET_HCA_CAP_OP_MODE_PORT_SELECTION - op_mod to operate
PORT_SELECTION_Capabilities.
Signed-off-by: Liu, Changcheng <jerrliu@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add support for setting NPPS. NPPS is currently available in
REAL_TIME_CLOCK mode only. In addition allow the user to set the pulse
duration.
When NPPS pulse duration is not set explicitly by the user, driver set
it to 50% of the NPPS period.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add management capability bits indicating firmware may support N pulses
per second. Add corresponding fields in MTPPS register.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Allows telling a mkey to use PCI ATS for DMA that flows through it.
Link: https://lore.kernel.org/r/1-v1-bd147097458e+ede-umem_dmabuf_jgg@nvidia.com
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Merge net/mlx5 dependencies for device DMA logging.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
MACsec EPN splits the packet number (PN) into two 32-bits fields,
epn_lsb (32 least significant bits (LSBs) of PN) and epn_msb (32
most significant bits (MSBs) of PN).
Epn_msb bits are managed by SW and for that HW is required to send
an object change event of type EPN event notifying the SW to update
the epn_msb in addition, once epn_msb is updated SW update HW with
the new epn_msb value for HW to perform replay protection.
To prevent HW from stopping while handling the event, SW manages
another bit for HW called epn_overlap, HW uses the latter to get
an indication regarding how to read the epn_msb value correctly
while still receiving packets.
Add epn event handling that updates the epn_overlap and epn_msb for
every 2^31 packets according to the following logic:
if epn_lsb crosses 2^31 (half sequence number wraparound) upon HW
relevant event, SW updates the esn_overlap value to OLD (value = 1).
When the epn_lsb crosses 2^32 (full sequence number wraparound)
upon HW relevant event, SW updates the esn_overlap to NEW
(value = 0) and increment the esn_msb.
When using MACsec EPN a salt and short secure channel id (ssci)
needs to be provided by the user, when offloading EPN need to pass
this salt and ssci to the HW to be used in the initial vector (IV)
calculations.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
protection
Add ifc bits related to advanced steering operations (ASO) and general
object modify for macsec to use as part of offloading EPN and replay
protection features.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix ifc fields name to be consistent with the device spec document.
Fixes: 8385c51ff5bc ("net/mlx5: Introduce MACsec Connect-X offload hardware bits and structures")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
drivers/net/ethernet/freescale/fec.h
7b15515fc1ca ("Revert "fec: Restart PPS after link state change"")
40c79ce13b03 ("net: fec: add stop mode support for imx8 platform")
https://lore.kernel.org/all/20220921105337.62b41047@canb.auug.org.au/
drivers/pinctrl/pinctrl-ocelot.c
c297561bc98a ("pinctrl: ocelot: Fix interrupt controller")
181f604b33cd ("pinctrl: ocelot: add ability to be used in a non-mmio configuration")
https://lore.kernel.org/all/20220921110032.7cd28114@canb.auug.org.au/
tools/testing/selftests/drivers/net/bonding/Makefile
bbb774d921e2 ("net: Add tests for bonding and team address list management")
152e8ec77640 ("selftests/bonding: add a test for bonding lladdr target")
https://lore.kernel.org/all/20220921110437.5b7dbd82@canb.auug.org.au/
drivers/net/can/usb/gs_usb.c
5440428b3da6 ("can: gs_usb: gs_can_open(): fix race dev->can.state condition")
45dfa45f52e6 ("can: gs_usb: add RX and TX hardware timestamp support")
https://lore.kernel.org/all/84f45a7d-92b6-4dc5-d7a1-072152fab6ff@tessares.net/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull rdma fixes from Jason Gunthorpe:
"Many bug fixes in several drivers:
- Fix misuse of the DMA API in rtrs
- Several irdma issues: hung task due to SQ flushing, incorrect
capability reporting to userspace, improper error handling for MW
corners, touching an uninitialized SGL for during invalidation.
- hns was using the wrong page size limits for the HW, an incorrect
calculation of wqe_shift causing WQE corruption, and mis computed a
timer id.
- Fix a crash in SRP triggered by blktests
- Fix compiler errors by calling virt_to_page() with the proper type
in siw
- Userspace triggerable deadlock in ODP
- mlx5 could use the wrong profile due to some driver loading races,
counters were not working in some device configurations, and a
crash on error unwind"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/irdma: Report RNR NAK generation in device caps
RDMA/irdma: Use s/g array in post send only when its valid
RDMA/irdma: Return correct WC error for bind operation failure
RDMA/irdma: Return error on MR deregister CQP failure
RDMA/irdma: Report the correct max cqes from query device
MAINTAINERS: Update maintainers of HiSilicon RoCE
RDMA/mlx5: Fix UMR cleanup on error flow of driver init
RDMA/mlx5: Set local port to one when accessing counters
RDMA/mlx5: Rely on RoCE fw cap instead of devlink when setting profile
IB/core: Fix a nested dead lock as part of ODP flow
RDMA/siw: Pass a pointer to virt_to_page()
RDMA/srp: Set scmnd->result only when scmnd is not NULL
RDMA/hns: Remove the num_qpc_timer variable
RDMA/hns: Fix wrong fixed value of qp->rq.wqe_shift
RDMA/hns: Fix supported page size
RDMA/cma: Fix arguments order in net device validation
RDMA/irdma: Fix drain SQ hang with no completion
RDMA/rtrs-srv: Pass the correct number of entries for dma mapped SGL
RDMA/rtrs-clt: Use the right sg_cnt after ib_dma_map_sg
|
|
Add new namespace for MACsec RX flows.
Encrypted MACsec packets should be first decrypted and stripped
from MACsec header and then continues with the kernel's steering
pipeline.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tx flow steering consists of two flow tables (FTs).
The first FT (crypto table) has two fixed rules:
One default miss rule so non MACsec offloaded packets bypass the MACSec
tables, another rule to make sure that MACsec key exchange (MKE) traffic
passes unencrypted as expected (matched of ethertype).
On each new MACsec offload flow, a new MACsec rule is added.
This rule is matched on metadata_reg_a (which contains the id of the
flow) and invokes the MACsec offload action on match.
The second FT (check table) has two fixed rules:
One rule for verifying that the previous offload actions were
finished successfully and packet need to be transmitted.
Another default rule for dropping packets that were failed in the
offload actions.
The MACsec FTs should be created on demand when the first MACsec rule is
added and destroyed when the last MACsec rule is deleted.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changed EGRESS_KERNEL namespace to EGRESS_IPSEC and add new
namespace for MACsec TX.
This namespace should be the last namespace for transmitted packets.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add MACsec offload related IFC structs, layouts and enumerations.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to support MACsec offload (and maybe some other crypto features
in the future), generalize flow action parameters / defines to be used by
crypto offlaods other than IPsec.
The following changes made:
ipsec_obj_id field at flow action context was changed to crypto_obj_id,
intreduced a new crypto_type field where IPsec is the default zero type
for backward compatibility.
Action ipsec_decrypt was changed to crypto_decrypt.
Action ipsec_encrypt was changed to crypto_encrypt.
IPsec offload code was updated accordingly for backward compatibility.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
esp_id is no longer in used
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Query ADV_VIRTUALIZATION capabilities which provide information for
advanced virtualization related features.
Current capabilities refer to the page tracker object which is used for
tracking the pages that are dirtied by the device.
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://lore.kernel.org/r/20220905105852.26398-3-yishaih@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Introduce ifc related stuff to enable using page tracker.
A page tracker is a dirty page tracking object used by the device to
report the tracking log.
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://lore.kernel.org/r/20220905105852.26398-2-yishaih@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Perform merge of Mellanox shared branch.
* mlx5-next:
RDMA/mlx5: Move function mlx5_core_query_ib_ppcnt() to mlx5_ib
|
|
This patch doesn't change any functionality, but move one function
to mlx5_ib because it is not used by mlx5_core.
The actual fix is in the next patch.
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Chris Mi <cmi@nvidia.com>
Link: https://lore.kernel.org/r/fd47b9138412bd94ed30f838026cbb4cf3878150.1661763871.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
When the RDMA auxiliary driver probes, it sets its profile based on
devlink driverinit value. The latter might not be in sync with FW yet
(In case devlink reload is not performed), thus causing a mismatch
between RDMA driver and FW. This results in the following FW syndrome
when the RDMA driver tries to adjust RoCE state, which fails the probe:
"0xC1F678 | modify_nic_vport_context: roce_en set on a vport that
doesn't support roce"
To prevent this, select the PF profile based on FW RoCE capability
instead of relying on devlink driverinit value.
To provide backward compatibility of the RoCE disable feature, on older
FW's where roce_rw is not set (FW RoCE capability is read-only), keep
the current behavior e.g., rely on devlink driverinit value.
Fixes: fbfa97b4d79f ("net/mlx5: Disable roce at HCA level")
Reviewed-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Michael Guralnik <michaelgur@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Link: https://lore.kernel.org/r/cb34ce9a1df4a24c135cb804db87f7d2418bd6cc.1661763459.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Add a lock_class_key per mlx5 device to avoid a false positive
"possible circular locking dependency" warning by lockdep, on flows
which lock more than one mlx5 device, such as adding SF.
kernel log:
======================================================
WARNING: possible circular locking dependency detected
5.19.0-rc8+ #2 Not tainted
------------------------------------------------------
kworker/u20:0/8 is trying to acquire lock:
ffff88812dfe0d98 (&dev->intf_state_mutex){+.+.}-{3:3}, at: mlx5_init_one+0x2e/0x490 [mlx5_core]
but task is already holding lock:
ffff888101aa7898 (&(¬ifier->n_head)->rwsem){++++}-{3:3}, at: blocking_notifier_call_chain+0x5a/0x130
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&(¬ifier->n_head)->rwsem){++++}-{3:3}:
down_write+0x90/0x150
blocking_notifier_chain_register+0x53/0xa0
mlx5_sf_table_init+0x369/0x4a0 [mlx5_core]
mlx5_init_one+0x261/0x490 [mlx5_core]
probe_one+0x430/0x680 [mlx5_core]
local_pci_probe+0xd6/0x170
work_for_cpu_fn+0x4e/0xa0
process_one_work+0x7c2/0x1340
worker_thread+0x6f6/0xec0
kthread+0x28f/0x330
ret_from_fork+0x1f/0x30
-> #0 (&dev->intf_state_mutex){+.+.}-{3:3}:
__lock_acquire+0x2fc7/0x6720
lock_acquire+0x1c1/0x550
__mutex_lock+0x12c/0x14b0
mlx5_init_one+0x2e/0x490 [mlx5_core]
mlx5_sf_dev_probe+0x29c/0x370 [mlx5_core]
auxiliary_bus_probe+0x9d/0xe0
really_probe+0x1e0/0xaa0
__driver_probe_device+0x219/0x480
driver_probe_device+0x49/0x130
__device_attach_driver+0x1b8/0x280
bus_for_each_drv+0x123/0x1a0
__device_attach+0x1a3/0x460
bus_probe_device+0x1a2/0x260
device_add+0x9b1/0x1b40
__auxiliary_device_add+0x88/0xc0
mlx5_sf_dev_state_change_handler+0x67e/0x9d0 [mlx5_core]
blocking_notifier_call_chain+0xd5/0x130
mlx5_vhca_state_work_handler+0x2b0/0x3f0 [mlx5_core]
process_one_work+0x7c2/0x1340
worker_thread+0x59d/0xec0
kthread+0x28f/0x330
ret_from_fork+0x1f/0x30
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&(¬ifier->n_head)->rwsem);
lock(&dev->intf_state_mutex);
lock(&(¬ifier->n_head)->rwsem);
lock(&dev->intf_state_mutex);
*** DEADLOCK ***
4 locks held by kworker/u20:0/8:
#0: ffff888150612938 ((wq_completion)mlx5_events){+.+.}-{0:0}, at: process_one_work+0x6e2/0x1340
#1: ffff888100cafdb8 ((work_completion)(&work->work)#3){+.+.}-{0:0}, at: process_one_work+0x70f/0x1340
#2: ffff888101aa7898 (&(¬ifier->n_head)->rwsem){++++}-{3:3}, at: blocking_notifier_call_chain+0x5a/0x130
#3: ffff88813682d0e8 (&dev->mutex){....}-{3:3}, at:__device_attach+0x76/0x460
stack backtrace:
CPU: 6 PID: 8 Comm: kworker/u20:0 Not tainted 5.19.0-rc8+
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Workqueue: mlx5_events mlx5_vhca_state_work_handler [mlx5_core]
Call Trace:
<TASK>
dump_stack_lvl+0x57/0x7d
check_noncircular+0x278/0x300
? print_circular_bug+0x460/0x460
? lock_chain_count+0x20/0x20
? register_lock_class+0x1880/0x1880
__lock_acquire+0x2fc7/0x6720
? register_lock_class+0x1880/0x1880
? register_lock_class+0x1880/0x1880
lock_acquire+0x1c1/0x550
? mlx5_init_one+0x2e/0x490 [mlx5_core]
? lockdep_hardirqs_on_prepare+0x400/0x400
__mutex_lock+0x12c/0x14b0
? mlx5_init_one+0x2e/0x490 [mlx5_core]
? mlx5_init_one+0x2e/0x490 [mlx5_core]
? _raw_read_unlock+0x1f/0x30
? mutex_lock_io_nested+0x1320/0x1320
? __ioremap_caller.constprop.0+0x306/0x490
? mlx5_sf_dev_probe+0x269/0x370 [mlx5_core]
? iounmap+0x160/0x160
mlx5_init_one+0x2e/0x490 [mlx5_core]
mlx5_sf_dev_probe+0x29c/0x370 [mlx5_core]
? mlx5_sf_dev_remove+0x130/0x130 [mlx5_core]
auxiliary_bus_probe+0x9d/0xe0
really_probe+0x1e0/0xaa0
__driver_probe_device+0x219/0x480
? auxiliary_match_id+0xe9/0x140
driver_probe_device+0x49/0x130
__device_attach_driver+0x1b8/0x280
? driver_allows_async_probing+0x140/0x140
bus_for_each_drv+0x123/0x1a0
? bus_for_each_dev+0x1a0/0x1a0
? lockdep_hardirqs_on_prepare+0x286/0x400
? trace_hardirqs_on+0x2d/0x100
__device_attach+0x1a3/0x460
? device_driver_attach+0x1e0/0x1e0
? kobject_uevent_env+0x22d/0xf10
bus_probe_device+0x1a2/0x260
device_add+0x9b1/0x1b40
? dev_set_name+0xab/0xe0
? __fw_devlink_link_to_suppliers+0x260/0x260
? memset+0x20/0x40
? lockdep_init_map_type+0x21a/0x7d0
__auxiliary_device_add+0x88/0xc0
? auxiliary_device_init+0x86/0xa0
mlx5_sf_dev_state_change_handler+0x67e/0x9d0 [mlx5_core]
blocking_notifier_call_chain+0xd5/0x130
mlx5_vhca_state_work_handler+0x2b0/0x3f0 [mlx5_core]
? mlx5_vhca_event_arm+0x100/0x100 [mlx5_core]
? lock_downgrade+0x6e0/0x6e0
? lockdep_hardirqs_on_prepare+0x286/0x400
process_one_work+0x7c2/0x1340
? lockdep_hardirqs_on_prepare+0x400/0x400
? pwq_dec_nr_in_flight+0x230/0x230
? rwlock_bug.part.0+0x90/0x90
worker_thread+0x59d/0xec0
? process_one_work+0x1340/0x1340
kthread+0x28f/0x330
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
</TASK>
Fixes: 6a3273217469 ("net/mlx5: SF, Port function state change support")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Pull virtio updates from Michael Tsirkin:
- A huge patchset supporting vq resize using the new vq reset
capability
- Features, fixes, and cleanups all over the place
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (88 commits)
vdpa/mlx5: Fix possible uninitialized return value
vdpa_sim_blk: add support for discard and write-zeroes
vdpa_sim_blk: add support for VIRTIO_BLK_T_FLUSH
vdpa_sim_blk: make vdpasim_blk_check_range usable by other requests
vdpa_sim_blk: check if sector is 0 for commands other than read or write
vdpa_sim: Implement suspend vdpa op
vhost-vdpa: uAPI to suspend the device
vhost-vdpa: introduce SUSPEND backend feature bit
vdpa: Add suspend operation
virtio-blk: Avoid use-after-free on suspend/resume
virtio_vdpa: support the arg sizes of find_vqs()
vhost-vdpa: Call ida_simple_remove() when failed
vDPA: fix 'cast to restricted le16' warnings in vdpa.c
vDPA: !FEATURES_OK should not block querying device config space
vDPA/ifcvf: support userspace to query features and MQ of a management device
vDPA/ifcvf: get_config_size should return a value no greater than dev implementation
vhost scsi: Allow user to control num virtqueues
vhost-scsi: Fix max number of virtqueues
vdpa/mlx5: Support different address spaces for control and data
vdpa/mlx5: Implement susupend virtqueue callback
...
|
|
Implement the suspend callback allowing to suspend the virtqueues so
they stop processing descriptors. This is required to allow to query a
consistent state of the virtqueue while live migration is taking place.
Signed-off-by: Eli Cohen <elic@nvidia.com>
Message-Id: <20220714113927.85729-2-elic@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Pull rdma updates from Jason Gunthorpe:
"This cycle we got a new RDMA driver "ERDMA" for the Alibaba cloud
environment. Otherwise the changes are dominated by rxe fixes.
There is another RDMA driver on the list that might get merged next
cycle, 'MANA' for the Azure cloud environment.
Summary:
- Bug fixes and small features for irdma, hns, siw, qedr, hfi1, mlx5
- General spelling/grammer fixes
- rdma cm can follow changes in neighbours for control packets
- Significant amounts of rxe fixes and spec compliance changes
- Use the modern NAPI API
- Use the bitmap API instead of open coding
- Performance improvements for rtrs
- Add the ERDMA driver for Alibaba cloud
- Fix a use after free bug in SRP"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (99 commits)
RDMA/ib_srpt: Unify checking rdma_cm_id condition in srpt_cm_req_recv()
RDMA/rxe: Fix error unwind in rxe_create_qp()
RDMA/mlx5: Add missing check for return value in get namespace flow
RDMA/rxe: Split qp state for requester and completer
RDMA/rxe: Generate error completion for error requester QP state
RDMA/rxe: Update wqe_index for each wqe error completion
RDMA/srpt: Fix a use-after-free
RDMA/srpt: Introduce a reference count in struct srpt_device
RDMA/srpt: Duplicate port name members
IB/qib: Fix repeated "in" within comments
RDMA/erdma: Add driver to kernel build environment
RDMA/erdma: Add the ABI definitions
RDMA/erdma: Add the erdma module
RDMA/erdma: Add connection management (CM) support
RDMA/erdma: Add verbs implementation
RDMA/erdma: Add verbs header file
RDMA/erdma: Add event queue implementation
RDMA/erdma: Add cmdq implementation
RDMA/erdma: Add main include file
RDMA/erdma: Add the hardware related definitions
...
|
|
After replacing the MR cache with an Mkey cache, rename the variables and
functions to fit the new meaning.
Link: https://lore.kernel.org/r/20220726071911.122765-6-michaelgur@nvidia.com
Signed-off-by: Aharon Landau <aharonl@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Add capability field which indicates the mask for wqe_counter which
connects between loopback CQE and the original WQE. With this connection
the driver can identify lost of the loopback CQE and reply PTP
synchronization with timestamp given in the original CQE.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add UID field to flow table attributes to allow creating flow tables
with a non default (zero) uid.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|