summaryrefslogtreecommitdiff
path: root/include/linux/ti_wilink_st.h
AgeCommit message (Collapse)AuthorFilesLines
2016-07-17drivers: misc: ti-st: Use int instead of fuzzy char for callback statusGeert Uytterhoeven1-1/+1
On mips and parisc: drivers/bluetooth/btwilink.c: In function 'ti_st_open': drivers/bluetooth/btwilink.c:174:21: warning: overflow in implicit constant conversion [-Woverflow] hst->reg_status = -EINPROGRESS; drivers/nfc/nfcwilink.c: In function 'nfcwilink_open': drivers/nfc/nfcwilink.c:396:31: warning: overflow in implicit constant conversion [-Woverflow] drv->st_register_cb_status = -EINPROGRESS; There are actually two issues: 1. Whether "char" is signed or unsigned depends on the architecture. As the completion callback data is used to pass a (negative) error code, it should always be signed. 2. EINPROGRESS is 150 on mips, 245 on parisc. Hence -EINPROGRESS doesn't fit in a signed 8-bit number. Change the callback status from "char" to "int" to fix these. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-09-21ti-st: use worker instead of calling st_int_write in wake upMuhammad Hamza Farooq1-0/+1
The wake up method is called with the port lock held. The st_int_write method calls port->ops->write with tries to acquire the lock again, causing CPU to wait infinitely. Right way to do is to write data to port in worker thread. Signed-off-by: Muhammad Hamza Farooq <mfarooq@visteon.com> Signed-off-by: Jacob Siverskog <jacob@teenage.engineering> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-05Revert "ti-st: add device tree support"Rob Herring1-1/+0
This reverts commit 46d0d33350e9b32642d745a8b46a954910196b4d. This binding is horrible and never should have been merged. It is not documented nor are there any in tree users, so reverting it will not break anything we care about. Lets revert it before we do have users. The problems with it are: - It is not documented. - The GPIO connection is described with a custom property and uses Linux GPIO numbering. - The UART connection is described using the Linux tty device name. Cc: Gigi Joseph <gigi.joseph@ti.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-02-04ti-st: clean up data types (fix harmless memory corruption)Dan Carpenter1-6/+6
The big issue here is: of_property_read_u32(np, "flow_cntrl", (u32 *)&dt_pdata->flow_cntrl); "->flow_cntrl" is a char so when we write a 32 bit number to it then it corrupts past the end of the char. It's probably hard to notice because the struct has padding so the code works on little endian systems. But on a big endian system the code would fail and on a 64 bit, big endian systems then "nshutdown_gpio" and "baud_rate" would be buggy as well. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-12ti-st: add device tree supportGigi Joseph1-0/+1
When using device tree, driver configuration data need to be read from device node. Add support for getting the platform data information from the device tree information stored in the .dtb file in case it exists. Signed-off-by: Eyal Reizer <eyalr@ti.com> Signed-off-by: bvijay <bvijay@ti.com> Diff rendering mode:inlineside by side Signed-off-by: Gigi Joseph <gigi.joseph@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-24misc: st_kim: Increase size of dev_name buffer to incorporate terminationLee Jones1-1/+1
Calling strncpy with a maximum size argument of 32 bytes on destination array kim_gdata->dev_name of size 32 bytes might leave the destination string unterminated. Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-08-16drivers/misc/ti-st: remove sparse warningsPavan Savoy1-1/+2
remove sparse warnings by assigning right storage specifiers to functions and also clean-up the declarations in the include/linux/ti_wilink_st.h Signed-off-by: Pavan Savoy <pavan_savoy@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-05-10ARM: OMAP: WiLink platform data for the PandaBoardMircea Gherzan1-0/+2
The "uim" deamon requires sysfs entries that are filled in using this platform data. Signed-off-by: Mircea Gherzan <mgherzan@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-08-23drivers:misc:ti-st: platform hooks for chip statesPavan Savoy1-1/+26
Certain platform specific or Host-WiLink Interface specific actions would be required to be taken when the chip is being enabled and after the chip is disabled such as configuration of the mux modes for the GPIO of host connected to the nshutdown of the chip or relinquishing UART after the chip is disabled. Similar actions can also be taken when the chip is in deep sleep or when the chip is awake. Performance enhancements such as configuring the host to run faster when chip is awake and slower when chip is asleep can also be made here. Signed-off-by: Pavan Savoy <pavan_savoy@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-23drivers:misc:ti-st: handle delayed tty receivePavan Savoy1-1/+2
When certain technologies shutdown their interface without waiting for the acknowledgement from the chip. The receive_buf from the TTY would be invoked a while after the relevant technology is unregistered. This patch introduces a new flag "is_registered" which maintains the state of protocols BT, FM or GPS and thereby removes the need to clear the protocol data from ST when protocols gets unregistered. This fixes corner cases when HCI RESET is sent down from bluetooth stack and the receive_buf is called from tty after 250ms before which bluetooth would have unregistered from the system. OR - when FM application decides to close down the device without sending a power-off FM command resulting in some RDS data or interrupt data coming in after the driver is unregistered. Signed-off-by: Pavan Savoy <pavan_savoy@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-04drivers:misc: ti-st: remove multiple gpio handlingPavan Savoy1-17/+2
TI shared transport driver previously intended to expose rfkill entries for each of the protocol gpio that the chip would have. However now in case such gpios exist, which requires to be enabled for a specific protocol, the responsibility lay on protocol driver. This patch removes the request/free of multiple gpios, rfkill struct references and also removes the chip_toggle function. Signed-off-by: Pavan Savoy <pavan_savoy@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-04drivers:misc: ti-st: firmware download optimizationPavan Savoy1-0/+6
To fasten the process of firmware download, the chip allows disabling of the command complete event generation from host. In these cases, only few very essential commands would have the command complete events and hence the wait associated with them. So now the driver would wait for a command complete event, only when it comes across a wait event during firmware parsing. This would also mean we need to skip not just the change baud rate command but also the wait for it. Signed-off-by: Pavan Savoy <pavan_savoy@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-04drivers:misc: ti-st: move from rfkill to sysfsPavan Savoy1-2/+17
The communication between ST KIM and UIM was interfaced over the /dev/rfkill device node. Move the interface to a simpler less abusive sysfs entry mechanism and document it in Documentation/ABI/testing/ under sysfs-platform-kim. Shared transport driver would now read the UART details originally received by bootloader or firmware as platform data. The data read will be shared over sysfs entries for the user-space UIM or other n/w manager/plugins to be read, and assist the driver by opening up the UART, setting the baud-rate and installing the line discipline. Signed-off-by: Pavan Savoy <pavan_savoy@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-04drivers:misc: ti-st: register with channel IDsPavan Savoy1-12/+28
The architecture of shared transport had begun with individual protocols like bluetooth, fm and gps telling the shared transport what sort of protocol they are and then expecting the ST driver to parse the incoming data from chip and forward data only relevant to the protocol drivers. This change would mean each protocol drivers would also send information to ST driver as to how to intrepret their protocol data coming out of the chip. Signed-off-by: Pavan Savoy <pavan_savoy@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-14drivers: misc: ti-st: fix review commentsPavan Savoy1-2/+0
Based on comments from Jiri Slaby, drop the register storage specifier, remove the unused code, cleanup the const to non-const type casting. Also make the line discipline ops structure static, since its a singleton, unmodified structure which need not be in heap. Reported-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Pavan Savoy <pavan_savoy@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-05staging: ti-st: mv ti_wilink_st headerPavan Savoy1-0/+402
Move the header to a standard linux device driver location. This should pave the way for other drivers to be moved into the relevant directories. ti_wilink_st.h is a common header file used by the TI's shared transport device driver for WiLink chipsets. Each individual protocol drivers like bluetooth driver, FM V4L2 driver and GPS drivers will make use of this header. Signed-off-by: Pavan Savoy <pavan_savoy@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>