| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Use low order bit of skb->_skb_dst to tell dst is not refcounted.
Change _skb_dst to _skb_refdst to make sure all uses are catched.
skb_dst() returns the dst, regardless of noref bit set or not, but
with a lockdep check to make sure a noref dst is not given if current
user is not rcu protected.
New skb_dst_set_noref() helper to set an notrefcounted dst on a skb.
(with lockdep check)
skb_dst_drop() drops a reference only if skb dst was refcounted.
skb_dst_force() helper is used to force a refcount on dst, when skb
is queued and not anymore RCU protected.
Use skb_dst_force() in __sk_add_backlog(), __dev_xmit_skb() if
!IFF_XMIT_DST_RELEASE or skb enqueued on qdisc queue, in
sock_queue_rcv_skb(), in __nf_queue().
Use skb_dst_force() in dev_requeue_skb().
Note: dst_use_noref() still dirties dst, we might transform it
later to do one dirtying per jiffies.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
include/linux/if_link.h
|
|
Now we have a set of nested attributes:
IFLA_VFINFO_LIST (NESTED)
IFLA_VF_INFO (NESTED)
IFLA_VF_MAC
IFLA_VF_VLAN
IFLA_VF_TX_RATE
This allows a single set to operate on multiple attributes if desired.
Among other things, it means a dump can be replayed to set state.
The current interface has yet to be released, so this seems like
something to consider for 2.6.34.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With RPS inclusion, skb timestamping is not consistent in RX path.
If netif_receive_skb() is used, its deferred after RPS dispatch.
If netif_rx() is used, its done before RPS dispatch.
This can give strange tcpdump timestamps results.
I think timestamping should be done as soon as possible in the receive
path, to get meaningful values (ie timestamps taken at the time packet
was delivered by NIC driver to our stack), even if NAPI already can
defer timestamping a bit (RPS can help to reduce the gap)
Tom Herbert prefer to sample timestamps after RPS dispatch. In case
sampling is expensive (HPET/acpi_pm on x86), this makes sense.
Let admins switch from one mode to another, using a new
sysctl, /proc/sys/net/core/netdev_tstamp_prequeue
Its default value (1), means timestamps are taken as soon as possible,
before backlog queueing, giving accurate timestamps.
Setting a 0 value permits to sample timestamps when processing backlog,
after RPS dispatch, to lower the load of the pre-RPS cpu.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now there's null check here and also again in the hook. Looking at bridge bits
which are simmilar, port structure is rcu_dereferenced right away in
handle_bridge and passed to hook. Looks nicer.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new function can be used to read/write large bitmaps via /proc. A
comma separated range format is used for compact output and input
(e.g. 1,3-4,10-10).
Writing into the file will first reset the bitmap then update it
based on the given input.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-next-2.6
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kaber/ipmr-2.6
|
|
Eliminate comments in TIPC's main API files that are either obsolete,
incorrect, misleading, or unhelpful. It also adds in one new comment.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Provide initial support for displaying overall TIPC status/statistics
information at runtime. Currently, only version info for the TIPC
kernel module is displayed.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
Documentation/feature-removal-schedule.txt
drivers/net/wireless/ath/ar9170/usb.c
drivers/scsi/iscsi_tcp.c
net/ipv4/ipmr.c
|
|
Originally, commit d899bf7b ("procfs: provide stack information for
threads") attempted to introduce a new feature for showing where the
threadstack was located and how many pages are being utilized by the
stack.
Commit c44972f1 ("procfs: disable per-task stack usage on NOMMU") was
applied to fix the NO_MMU case.
Commit 89240ba0 ("x86, fs: Fix x86 procfs stack information for threads on
64-bit") was applied to fix a bug in ia32 executables being loaded.
Commit 9ebd4eba7 ("procfs: fix /proc/<pid>/stat stack pointer for kernel
threads") was applied to fix a bug which had kernel threads printing a
userland stack address.
Commit 1306d603f ('proc: partially revert "procfs: provide stack
information for threads"') was then applied to revert the stack pages
being used to solve a significant performance regression.
This patch nearly undoes the effect of all these patches.
The reason for reverting these is it provides an unusable value in
field 28. For x86_64, a fork will result in the task->stack_start
value being updated to the current user top of stack and not the stack
start address. This unpredictability of the stack_start value makes
it worthless. That includes the intended use of showing how much stack
space a thread has.
Other architectures will get different values. As an example, ia64
gets 0. The do_fork() and copy_process() functions appear to treat the
stack_start and stack_size parameters as architecture specific.
I only partially reverted c44972f1 ("procfs: disable per-task stack usage
on NOMMU") . If I had completely reverted it, I would have had to change
mm/Makefile only build pagewalk.o when CONFIG_PROC_PAGE_MONITOR is
configured. Since I could not test the builds without significant effort,
I decided to not change mm/Makefile.
I only partially reverted 89240ba0 ("x86, fs: Fix x86 procfs stack
information for threads on 64-bit") . I left the KSTK_ESP() change in
place as that seemed worthwhile.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Stefani Seibold <stefani@seibold.net>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
Conflicts:
drivers/net/wireless/ath/ar9170/main.c
|
|
|
|
Since xt_action_param is writable, let's use it. The pointer to
'bool hotdrop' always worried (8 bytes (64-bit) to write 1 byte!).
Surprisingly results in a reduction in size:
text data bss filename
5457066 692730 357892 vmlinux.o-prev
5456554 692730 357892 vmlinux.o
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
|
|
In future, layer-3 matches will be an xt module of their own, and
need to set the fragoff and thoff fields. Adding more pointers would
needlessy increase memory requirements (esp. so for 64-bit, where
pointers are wider).
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
|
|
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
|
|
The structures carried - besides match/target - almost the same data.
It is possible to combine them, as extensions are evaluated serially,
and so, the callers end up a little smaller.
text data bss filename
-15318 740 104 net/ipv4/netfilter/ip_tables.o
+15286 740 104 net/ipv4/netfilter/ip_tables.o
-15333 540 152 net/ipv6/netfilter/ip6_tables.o
+15269 540 152 net/ipv6/netfilter/ip6_tables.o
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
|
|
This patch adds support for multiple independant multicast routing instances,
named "tables".
Userspace multicast routing daemons can bind to a specific table instance by
issuing a setsockopt call using a new option MRT6_TABLE. The table number is
stored in the raw socket data and affects all following ip6mr setsockopt(),
getsockopt() and ioctl() calls. By default, a single table (RT6_TABLE_DFLT)
is created with a default routing rule pointing to it. Newly created pim6reg
devices have the table number appended ("pim6regX"), with the exception of
devices created in the default table, which are named just "pim6reg" for
compatibility reasons.
Packets are directed to a specific table instance using routing rules,
similar to how regular routing rules work. Currently iif, oif and mark
are supported as keys, source and destination addresses could be supported
additionally.
Example usage:
- bind pimd/xorp/... to a specific table:
uint32_t table = 123;
setsockopt(fd, SOL_IPV6, MRT6_TABLE, &table, sizeof(table));
- create routing rules directing packets to the new table:
# ip -6 mrule add iif eth0 lookup 123
# ip -6 mrule add oif eth0 lookup 123
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
Now that cache entries in unres_queue don't need to be distinguished by their
network namespace pointer anymore, we can remove it from struct mfc6_cache
add pass the namespace as function argument to the functions that need it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
Conflicts:
net/bridge/br_device.c
net/bridge/br_forward.c
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: create rcu_my_thread_group_empty() wrapper
memcg: css_id() must be called under rcu_read_lock()
cgroup: Check task_lock in task_subsys_state()
sched: Fix an RCU warning in print_task()
cgroup: Fix an RCU warning in alloc_css_id()
cgroup: Fix an RCU warning in cgroup_path()
KEYS: Fix an RCU warning in the reading of user keys
KEYS: Fix an RCU warning
|
|
Currently (all tested with hwsim) you can do stupid
things like setting up an AP on a certain channel,
then adding another virtual interface and making
that associate on another channel -- this will make
the beaconing to move channel but obviously without
the necessary IEs data update.
In order to improve this situation, first make the
configuration APIs (cfg80211 and nl80211) aware of
multi-channel operation -- we'll eventually need
that in the future anyway. There's one userland API
change and one API addition. The API change is that
now SET_WIPHY must be called with virtual interface
index rather than only wiphy index in order to take
effect for that interface -- luckily all current
users (hostapd) do that. For monitor interfaces, the
old setting is preserved, but monitors are always
slaved to other devices anyway so no guarantees.
The second userland API change is the introduction
of a per virtual interface SET_CHANNEL command, that
hostapd should use going forward to make it easier
to understand what's going on (it can automatically
detect a kernel with this command).
Other than mac80211, no existing cfg80211 drivers
are affected by this change because they only allow
a single virtual interface.
mac80211, however, now needs to be aware that the
channel settings are per interface now, and needs
to disallow (for now) real multi-channel operation,
which is another important part of this patch.
One of the immediate benefits is that you can now
start hostapd to operate on a hardware that already
has a connection on another virtual interface, as
long as you specify the same channel.
Note that two things are left unhandled (this is an
improvement -- not a complete fix):
* different HT/no-HT modes
currently you could start an HT AP and then
connect to a non-HT network on the same channel
which would configure the hardware for no HT;
that can be fixed fairly easily
* CSA
An AP we're connected to on a virtual interface
might indicate switching channels, and in that
case we would follow it, regardless of how many
other interfaces are operating; this requires
more effort to fix but is pretty rare after all
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
eth_type_trans() & get_rps_cpus() currently need two 64bytes cache
lines in packet to compute rxhash.
Increasing NET_SKB_PAD from 32 to 64 reduces the need to one cache
line only, and makes RPS faster.
NET_IP_ALIGN(2) + ethernet_header(14) + IP_header(20/40) + ports(8)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some RCU-lockdep splat repairs need to know whether they are running
in a single-threaded process. Unfortunately, the thread_group_empty()
primitive is defined in sched.h, and can induce #include hell. This
commit therefore introduces a rcu_my_thread_group_empty() wrapper that
is defined in rcupdate.c, thus avoiding the need to include sched.h
everywhere.
Signed-off-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This whole patchset is for adding netpoll support to bridge and bonding
devices. I already tested it for bridge, bonding, bridge over bonding,
and bonding over bridge. It looks fine now.
To make bridge and bonding support netpoll, we need to adjust
some netpoll generic code. This patch does the following things:
1) introduce two new priv_flags for struct net_device:
IFF_IN_NETPOLL which identifies we are processing a netpoll;
IFF_DISABLE_NETPOLL is used to disable netpoll support for a device
at run-time;
2) introduce one new method for netdev_ops:
->ndo_netpoll_cleanup() is used to clean up netpoll when a device is
removed.
3) introduce netpoll_poll_dev() which takes a struct net_device * parameter;
export netpoll_send_skb() and netpoll_poll_dev() which will be used later;
4) hide a pointer to struct netpoll in struct netpoll_info, ditto.
5) introduce ->real_dev for struct netpoll.
6) introduce a new status NETDEV_BONDING_DESLAE, which is used to disable
netconsole before releasing a slave, to avoid deadlocks.
Cc: David Miller <davem@davemloft.net>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
Conflicts:
drivers/net/wireless/libertas_tf/cmd.c
drivers/net/wireless/libertas_tf/main.c
|
|
With following patch I can reach maximum rate of my pktgen+udpsink
simulator :
- 'old' machine : dual quad core E5450 @3.00GHz
- 64 UDP rx flows (only differ by destination port)
- RPS enabled, NIC interrupts serviced on cpu0
- rps dispatched on 7 other cores. (~130.000 IPI per second)
- SLAB allocator (faster than SLUB in this workload)
- tg3 NIC
- 1.080.000 pps without a single drop at NIC level.
Idea is to add two prefetchw() calls in __alloc_skb(), one to prefetch
first sk_buff cache line, the second to prefetch the shinfo part.
Also using one memset() to initialize all skb_shared_info fields instead
of one by one to reduce number of instructions, using long word moves.
All skb_shared_info fields before 'dataref' are cleared in
__alloc_skb().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Expand task_subsys_state()'s rcu_dereference_check() to include the full
locking rule as documented in Documentation/cgroups/cgroups.txt by adding
a check for task->alloc_lock being held.
This fixes an RCU false positive when resuming from suspend. The warning
comes from freezer cgroup in cgroup_freezing_or_frozen().
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
Using a single list for all userspace devices leads to a dead lock
on multiplexed buses in some circumstances (mux chip instantiated
from userspace). This is solved by using a separate list for each
bus segment.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Michael Lawnick <ml.lawnick@gmx.de>
|
|
Add hlist_for_each_entry_rcu_bh() and
hlist_for_each_entry_continue_rcu_bh() macros, and use them in
ipv6_get_ifaddr(), if6_get_first() and if6_get_next() to fix lockdeps
warnings.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
virtio added mergeable buffers mode where 2 bytes of extra info is put
after vnet header but before actual data (tun does not need this data).
In hindsight, it would have been better to add the new info *before* the
packet: as it is, users need a lot of tricky code to skip the extra 2
bytes in the middle of the iovec, and in fact applications seem to get
it wrong, and only work with specific iovec layout. The fact we might
need to split iovec also means we might in theory overflow iovec max
size.
This patch adds a simpler way for applications to handle this,
and future proofs the interface against further extensions,
by making the size of the virtio net header configurable
from userspace. As a result, tun driver will simply
skip the extra 2 bytes on both input and output.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Per cpu variable softnet_data.total was shared between IRQ and SoftIRQ context
without any protection. And enqueue_to_backlog should update the netdev_rx_stat
of the target CPU.
This patch renames softnet_data.total to softnet_data.processed: the number of
packets processed in uppper levels(IP stacks).
softnet_stat data is moved into softnet_data.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
include/linux/netdevice.h | 17 +++++++----------
net/core/dev.c | 26 ++++++++++++--------------
net/sched/sch_generic.c | 2 +-
3 files changed, 20 insertions(+), 25 deletions(-)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 6be8ac2f ("[NET]: uninline skb_pull, de-bloats a lot")
we uninlined skb_pull.
But in some critical paths it makes sense to inline this thing
and it helps performance significantly.
Create an skb_pull_inline() so that we can do this in a way that
serves also as annotation.
Based upon a patch by Eric Dumazet.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sk_callback_lock rwlock actually protects sk->sk_sleep pointer, so we
need two atomic operations (and associated dirtying) per incoming
packet.
RCU conversion is pretty much needed :
1) Add a new structure, called "struct socket_wq" to hold all fields
that will need rcu_read_lock() protection (currently: a
wait_queue_head_t and a struct fasync_struct pointer).
[Future patch will add a list anchor for wakeup coalescing]
2) Attach one of such structure to each "struct socket" created in
sock_alloc_inode().
3) Respect RCU grace period when freeing a "struct socket_wq"
4) Change sk_sleep pointer in "struct sock" by sk_wq, pointer to "struct
socket_wq"
5) Change sk_sleep() function to use new sk->sk_wq instead of
sk->sk_sleep
6) Change sk_has_sleeper() to wq_has_sleeper() that must be used inside
a rcu_read_lock() section.
7) Change all sk_has_sleeper() callers to :
- Use rcu_read_lock() instead of read_lock(&sk->sk_callback_lock)
- Use wq_has_sleeper() to eventually wakeup tasks.
- Use rcu_read_unlock() instead of read_unlock(&sk->sk_callback_lock)
8) sock_wake_async() is modified to use rcu protection as well.
9) Exceptions :
macvtap, drivers/net/tun.c, af_unix use integrated "struct socket_wq"
instead of dynamically allocated ones. They dont need rcu freeing.
Some cleanups or followups are probably needed, (possible
sk_callback_lock conversion to a spinlock for example...).
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
[added compatibility macros so we can convert things easier - gregkh]
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
nfs: fix memory leak in nfs_get_sb with CONFIG_NFS_V4
nfs: fix some issues in nfs41_proc_reclaim_complete()
NFS: Ensure that nfs_wb_page() waits for Pg_writeback to clear
NFS: Fix an unstable write data integrity race
nfs: testing for null instead of ERR_PTR()
NFS: rsize and wsize settings ignored on v4 mounts
NFSv4: Don't attempt an atomic open if the file is a mountpoint
SUNRPC: Fix a bug in rpcauth_prune_expired
|
|
Changes:
This is a complete re-write of the socket layer. Making the socket
implementation more aligned with the other socket layers and using more
of the support functions available in sock.c. Lots of code is copied
from af_unix (and some from af_irda).
Non-blocking mode should be working as well.
Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
coda: move backing-dev.h kernel include inside __KERNEL__
mtd: ensure that bdi entries are properly initialized and registered
Move mtd_bdi_*mappable to mtdcore.c
btrfs: convert to using bdi_setup_and_register()
Catch filesystems lacking s_bdi
drbd: Terminate a connection early if sending the protocol fails
drbd: fix memory leak
Fix JFFS2 sync silent failure
smbfs: add bdi backing to mount session
ncpfs: add bdi backing to mount session
exofs: add bdi backing to mount session
ecryptfs: add bdi backing to mount session
coda: add bdi backing to mount session
cifs: add bdi backing to mount session
afs: add bdi backing to mount session.
9p: add bdi backing to mount session
bdi: add helper function for doing init and register of a bdi for a file system
block: ensure jiffies wrap is handled correctly in blk_rq_timed_out_timer
|
|
Otherwise we must export backing-dev.h as well, which doesn't make
any sense.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
batch skb dequeueing from softnet input_pkt_queue to reduce potential lock
contention when RPS is enabled.
Note: in the worst case, the number of packets in a softnet_data may
be double of netdev_max_backlog.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
reimplement softnet_data.output_queue as a FIFO queue to keep the
fairness among the qdiscs rescheduled.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
----
include/linux/netdevice.h | 1 +
net/core/dev.c | 22 ++++++++++++----------
2 files changed, 13 insertions(+), 10 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is used to configure APs to not bridge traffic between connected stations.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kaber/ipmr-2.6
|
